Skip to contentSkip to conversation

sata_sil driver dev 0 failed to IDENTIFY (INIT_DEV_PARAMS failed)

DISCUSSION Eric Schoeller 2 participants 2 messages Aug 14, 2006

lore
Share & tools
lore
#0 lore raw

howdy,

i am using the sata_sil driver with a Silicon Image, Inc. SiI 3112 Controller and have recently started receiving these messages on driver load:

[17179867.424000] libata version 1.20 loaded.
[17179958.936000] sata_sil 0000:02:0b.0: version 0.9
[17179958.936000] ACPI: PCI Interrupt 0000:02:0b.0[A] -> Link [LNKA] ->
GSI 3 (level, low) -> IRQ 3
[17179958.936000] ata1: SATA max UDMA/100 cmd 0xD0838080 ctl 0xD083808A
bmdma 0xD0838000 irq 3
[17179958.936000] ata2: SATA max UDMA/100 cmd 0xD08380C0 ctl 0xD08380CA bmdma 0xD0838008 irq 3
[17179966.296000] ata1 is slow to respond, please be patient
[17179975.928000] ata1: SATA link up 1.5 Gbps (SStatus 113)
[17179975.928000] ata1: dev 0 failed to IDENTIFY (INIT_DEV_PARAMS failed)
[17179975.928000] scsi0 : sata_sil
[17179976.132000] ata2: SATA link down (SStatus 0)

As a result, the maxtor 250gb drive fails to be detected :(
I'm roughly 1900 miles away from this box so I have no ability to physically inspect the device. I'm worried that the drive is blown (sure wish smartmontools was compatible with libata so I might have seen this coming sooner!) but after checking the usual sources I'm still not entirely sure what this error message means exactly.

Any insights are greatly appreciated!

Eric Schoeller
Linux 2.6.17.8 #1 SMP Sun Aug 13 17:49:13 MDT 2006 i686 Intel(R) Pentium(R) 4 CPU 1400MHz GNU/Linux

#1 lore raw
Quoted 19 lines · Eric Schoeller

howdy,

i am using the sata_sil driver with a Silicon Image, Inc. SiI 3112 Controller and have recently started receiving these messages on driver load:

[17179867.424000] libata version 1.20 loaded.
[17179958.936000] sata_sil 0000:02:0b.0: version 0.9
[17179958.936000] ACPI: PCI Interrupt 0000:02:0b.0[A] -> Link [LNKA] ->
GSI 3 (level, low) -> IRQ 3
[17179958.936000] ata1: SATA max UDMA/100 cmd 0xD0838080 ctl 0xD083808A
bmdma 0xD0838000 irq 3
[17179958.936000] ata2: SATA max UDMA/100 cmd 0xD08380C0 ctl 0xD08380CA bmdma 0xD0838008 irq 3
[17179966.296000] ata1 is slow to respond, please be patient
[17179975.928000] ata1: SATA link up 1.5 Gbps (SStatus 113)
[17179975.928000] ata1: dev 0 failed to IDENTIFY (INIT_DEV_PARAMS failed)
[17179975.928000] scsi0 : sata_sil
[17179976.132000] ata2: SATA link down (SStatus 0)
Quoted 5 lines

As a result, the maxtor 250gb drive fails to be detected :(
I'm roughly 1900 miles away from this box so I have no ability to physically inspect the device. I'm worried that the drive is blown (sure wish smartmontools was compatible with libata so I might have seen this coming sooner!) but after checking the usual sources I'm still not

smartmontools works just fine with libata, and has for quite a while.

Quoted 1 line

Any insights are greatly appreciated!

Switch out the drive and/or cable and see what happens...

Jeff