PCI: Cannot allocate resource region 7 of bridge 0000:00:04.0
I get these messages with 2.6.18-rc4 on i386:
PCI: Cannot allocate resource region 7 of bridge 0000:00:04.0
PCI: Cannot allocate resource region 8 of bridge 0000:00:04.0
PCI: Cannot allocate resource region 9 of bridge 0000:00:04.0
PCI: Cannot allocate resource region 7 of bridge 0000:00:05.0
PCI: Cannot allocate resource region 8 of bridge 0000:00:05.0
For these PCI bridges:
00:04.0 PCI bridge: ATI Technologies Inc Unknown device 5a36 (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=02, subordinate=03, sec-latency=0
Capabilities: [50] Power Management version 3
Capabilities: [58] Express Root Port (Slot-) IRQ 0
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable+
Capabilities: [b0] #0d [0000]
Capabilities: [b8] HyperTransport: MSI Mapping
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Virtual Channel
00:05.0 PCI bridge: ATI Technologies Inc Unknown device 5a37 (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=04, subordinate=05, sec-latency=0
Capabilities: [50] Power Management version 3
Capabilities: [58] Express Root Port (Slot-) IRQ 0
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable+
Capabilities: [b0] #0d [0000]
Capabilities: [b8] HyperTransport: MSI Mapping
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Virtual Channel
Adding some debug:
arch/i386/pci/i386.c +4 -1
@@ -100,6 +100,7 @@struct pci_dev *dev;int idx;struct resource *r, *pr; +int ret;/* Depth-First Search on bus tree */ list_for_each_entry (bus, bus_list, node) {
@@ -109,8 +110,10 @@if (!r->flags)continue ; pr =pci_find_parent_resource (dev, r); -if (!r->start || !pr ||request_resource (pr, r) <0 ) { + ret =0 ; +if (!r->start || !pr || (ret =request_resource (pr, r)) <0 ) {printk (KERN_ERR "PCI: Cannot allocate resource region %d of bridge %s\n" , idx,pci_name (dev)); +printk (KERN_ERR "PCI: start = %p, parent = %p, ret = %d\n" , r->start, pr, ret);/* Something is wrong with the region. Invalidate the resource to prevent child resource allocations in this range. */
r->start is zero in every case.
Some PCI debug messages for one bridge:
PCI: Using MMCONFIG
...
PCI: Scanning behind PCI bridge 0000:00:04.0, config 030200, pass 0
PCI: Scanning bus 0000:02
PCI: Fixups for bus 0000:02
PCI: Bus scan for 0000:02 returning with max=02
...
PCI: Scanning behind PCI bridge 0000:00:04.0, config 030200, pass 1
...
PCI: Bridge: 0000:00:04.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
...
PCI: Enabling bus mastering for device 0000:00:04.0
PCI: Setting latency timer of device 0000:00:04.0 to 64
...
PCI: Setting latency timer of device 0000:00:04.0 to 64 pcie_portdrv_probe->Dev[5a36:1002] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:04.0:pcie00]
PM: Adding info for pci_express:0000:00:04.0:pcie00 Allocate Port Service[0000:00:04.0:pcie01]
PM: Adding info for pci_express:0000:00:04.0:pcie01 Allocate Port Service[0000:00:04.0:pcie03]
PM: Adding info for pci_express:0000:00:04.0:pcie03
It says (twice) it is setting latency timer to 64 yet lspci says it's zero.
I tried pci=nobios. What else should I try?
Signature · 1 line
Chuck