Skip to contentSkip to conversation

Problem with USB storage devices, error -110

DISCUSSION Jan-Hendrik Zab 3 participants 4 messages Aug 31, 2006 – Sep 1, 2006

lore
Share & tools
lore
#0 lore raw

Hello,
any USB storage devices (like an external USB HDD) that I connect to the USB PCI adaptor card fail to be 'recognized' correctly by the kernel. The dmesg output looks like this:

usb 3-1: new full speed USB device using uhci_hcd and address 2 usb usb2: suspend_rh (auto-stop)
usb 3-1: ep0 maxpacket = 8
usb 3-1: khubd timed out on ep0in len=-8/18
usb 3-1: device descriptor read/all, error -110
usb 3-1: new full speed USB device using uhci_hcd and address 3 usb 3-1: khubd timed out on ep0in len=-8/64
usb 3-1: khubd timed out on ep0in len=-8/64
usb 3-1: khubd timed out on ep0in len=-8/64
usb 3-1: device descriptor read/64, error -110
usb 3-1: khubd timed out on ep0in len=-8/64
usb 3-1: khubd timed out on ep0in len=-8/64
usb 3-1: khubd timed out on ep0in len=-8/64
usb 3-1: device descriptor read/64, error -110
usb 3-1: new full speed USB device using uhci_hcd and address 4

I've also uploaded the complete dmesg output to:
http://v3ng34nce.org/dmesg_output.bz2

The computer where the problem appears is running kernel 2.6.18-rc5 now, after showing similar errors under the 'unstable' SMP Debian kernel 2.6.17-1-686.

Greets,
Jan-Hendrik Zab

Signature · 3 lines
| Jan-Hendrik Zab
| +49 (0)1773392888
| http://www.v3ng34nce.org
#1 lore raw
Quoted 21 lines · Jan-Hendrik Zab

Hello,
any USB storage devices (like an external USB HDD) that I connect to the USB PCI adaptor card fail to be 'recognized' correctly by the kernel. The dmesg output looks like this:

usb 3-1: new full speed USB device using uhci_hcd and address 2 usb usb2: suspend_rh (auto-stop)
usb 3-1: ep0 maxpacket = 8
usb 3-1: khubd timed out on ep0in len=-8/18
usb 3-1: device descriptor read/all, error -110
usb 3-1: new full speed USB device using uhci_hcd and address 3 usb 3-1: khubd timed out on ep0in len=-8/64
usb 3-1: khubd timed out on ep0in len=-8/64
usb 3-1: khubd timed out on ep0in len=-8/64
usb 3-1: device descriptor read/64, error -110
usb 3-1: khubd timed out on ep0in len=-8/64
usb 3-1: khubd timed out on ep0in len=-8/64
usb 3-1: khubd timed out on ep0in len=-8/64
usb 3-1: device descriptor read/64, error -110
usb 3-1: new full speed USB device using uhci_hcd and address 4

Quoted 6 lines

I've also uploaded the complete dmesg output to:
http://v3ng34nce.org/dmesg_output.bz2

The computer where the problem appears is running kernel 2.6.18-rc5 now, after showing similar errors under the 'unstable' SMP Debian kernel 2.6.17-1-686.

It seems pretty clear that the UHCI controller hardware on your PCI card isn't working. The "len=-8/64" messages are a dead giveaway; you can't get a negative length with a timeout failure if the controller is working right. At least, not unless you have some other USB devices already attached to the same controller and using up all the bandwidth.

The fact that it fails in the same way with all the USB devices you attach is another indicator that the controller is bad.

Alan Stern

#2 lore raw
Quoted 11 lines

Subject: Re: [linux-usb-devel] Problem with USB storage devices, error -110

It seems pretty clear that the UHCI controller hardware on your PCI card isn't working. The "len=-8/64" messages are a dead giveaway; you can't get a negative length with a timeout failure if the controller is working right. At least, not unless you have some other USB devices already attached to the same controller and using up all the bandwidth.

The fact that it fails in the same way with all the USB devices you attach is another indicator that the controller is bad.

BTW, error 110 is ETIMEDOUT. I have had that on one buggy USB mp3 player too - so it's not always the USB host controller.

Jan Engelhardt

#3 lore raw
In reply to Alan Stern
Quoted 9 lines · On Fri, 1 Sep 2006 10:12:35 -0400 (EDT) Alan Stern <[email protected]>…

It seems pretty clear that the UHCI controller hardware on your PCI card isn't working. The "len=-8/64" messages are a dead giveaway; you can't get a negative length with a timeout failure if the controller is working right. At least, not unless you have some other USB devices already attached to the same controller and using up all the bandwidth.

The fact that it fails in the same way with all the USB devices you attach is another indicator that the controller is bad.

Thanks for the answers. :)

There is also a HP Deskjet 5652 attached to the card which is recognized correctly and works just fine, as long as I do not insert any USB storage device. Of course the printer is just a USB 1.1 device. So I've tried without the ehci_hcd module loaded and everything seemed to work as it should. (Well, sorry for not trying this earlier.) So, at least the UHCI part seems to work as long as there are no EHCI 'functions' involved.
I'll try to get a new adaptor card then.

Greets,
Jan-Hendrik Zab