EtherIP tunnel driver (RFC 3378)
Subsystems (2)
PATCH 1/1 EtherIP tunnel driver (RFC 3378)
This driver implements the tunneling of Ethernet packets over IPv4 networks for Linux. It uses the protocol defined in RFC 3378. The protocol is also implemented by various BSD derivates and the Linux driver is interoperable with them (tested with NetBSD). The driver is also tested on different hardware platforms (currently i386 and 32bit HP-PA)
include/linux/in.h +1 -0
@@ -40,6 +40,7 @@ enum {IPPROTO_ESP =50 ,/* Encapsulation Security Payload protocol */ IPPROTO_AH =51 ,/* Authentication Header protocol */ +IPPROTO_ETHERIP =97 ,/* Ethernet over IPv4 protocol */ IPPROTO_PIM =103 ,/* Protocol Independent Multicast */ IPPROTO_COMP = 108, /* Compression Header protocol */
net/ipv4/etherip.c +546 -0
546 lines not on this page · raw message
net/ipv4/Kconfig +14 -0
@@ -272,6 +272,20 @@ config NET_IPGRE_BROADCAST Network), but can be distributed all over the Internet. If you want to do that, say Y here and to "IP multicast routing" below. +config NET_ETHERIP + tristate "IP: Ethernet over IP tunneling (experimental)" + help + Tunneling means encapsulating data of one protocol type within + another protocol and sending it over a channel that understands the + encapsulating protocol. This tunnel driver implements the + encapsulation of Ethernet frames into IP packets using the EtherIP + protocol defined in RFC 3378. This is especially usefull together with + the bridging code to build distributed OSI Layer 2 networks. + + To configure tunnels an extra tool is required. You can download + it from http://zlug.fh-zwickau.de/~joro/projects/ under the + EtherIP section. If unsure, say N. + config IP_MROUTE bool "IP: multicast routing" depends on IP_MULTICAST
net/ipv4/Makefile +1 -0
@@ -17,6 +17,7 @@ obj-$(CONFIG_PROC_FS) += proc.o obj-$(CONFIG_IP_MULTIPLE_TABLES) += fib_rules.o obj-$(CONFIG_IP_MROUTE) += ipmr.o obj-$(CONFIG_NET_IPIP) += ipip.o +obj-$(CONFIG_NET_ETHERIP) += etherip.o obj-$(CONFIG_NET_IPGRE) += ip_gre.o obj-$(CONFIG_SYN_COOKIES) += syncookies.o obj-$(CONFIG_INET_AH) += ah4.o
There are lots of whitespace errors (trailing whitespace, whitespace following opening parens, no whitespace after comma, ...) which I'm going to ignore below, please fix them anyway.
Quoted 85 lines · Joerg Roedel
diff -uprN -X linux-2.6.17.13/Documentation/dontdiff
linux-2.6.17.13-vanilla/net/ipv4/etherip.clinux-2.6.17.13/net/ipv4/etherip.cnet/ipv4/etherip.c +81
-0@@ -0,0 +1,546 @@ +/* +* etherip.c: Ethernet over IPv4 tunnel driver (according to RFC3378) +* +* This driver could be used to tunnel Ethernet packets through IPv4 +* networks. This is especially usefull together with the bridging +* code in Linux. +* +* This code was written with an eye on the IPIP driver in linux from +* Sam Lantinga. Thanks for the great work. +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License +* version 2 (no later version) as published by the +* Free Software Foundation. +* +*/ + +#include <linux/capability.h> +#include <linux/init.h> +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/types.h> +#include <linux/mutex.h> +#include <linux/netdevice.h> +#include <linux/etherdevice.h> +#include <linux/skbuff.h> +#include <linux/ip.h> +#include <linux/if_tunnel.h> +#include <linux/list.h> +#include <linux/string.h> +#include <linux/netfilter_ipv4.h> +#include <net/ip.h> +#include <net/protocol.h> +#include <net/route.h> +#include <net/ipip.h> +#include <net/xfrm.h> + +MODULE_LICENSE ("GPL" ); +MODULE_AUTHOR ("Joerg Roedel <[email protected]>" ); +MODULE_DESCRIPTION ("Ethernet over IPv4 tunnel driver" ); + +/* +* These 2 defines are taken from ipip.c - if it's good enough for them +* it's good enough for me. +*/ +#define HASH_SIZE 16 +#define HASH (addr) ((addr^(addr>>4))&0xF) + +#define ETHERIP_HEADER ((u16)0x0300) +#define ETHERIP_HLEN 2 + +#define BANNER1 "etherip: Ethernet over IPv4 tunneling driver\n" +#define BANNER2 "etherip: (C) 2006 by Joerg Roedel <[email protected]>\n" + +struct etherip_tunnel { +struct list_head list; +struct net_device *dev; +struct net_device_stats stats; +struct ip_tunnel_parm parms; +unsigned int recursion; +}; + +static struct net_device *etherip_tunnel_dev; +static struct list_head tunnels[HASH_SIZE ]; + +static DEFINE_RWLOCK (etherip_lock); + +static void etherip_tunnel_setup (struct net_device *dev); + +/* add a tunnel to the hash */ +static void etherip_tunnel_add (struct etherip_tunnel *tun) +{ +unsigned h =HASH (tun->parms.iph.daddr); +list_add_tail (&tun->list, &tunnels[h]); +} + +/* delete a tunnel from the hash*/ +static void etherip_tunnel_del (struct etherip_tunnel *tun) +{ +list_del (&tun->list); +}
net/ipv4/etherip.c line 91
Quoted 10 lines
net/ipv4/etherip.c +10
-0+ +/* find a tunnel in the hash by parameters from userspace */ +static struct etherip_tunnel *etherip_tunnel_find (struct ip_tunnel_parm *p) +{ +struct list_head *ptr; +struct etherip_tunnel *ret; +unsigned h =HASH (p->iph.daddr); + +list_for_each (ptr, &tunnels[h]) { + ret = list_entry(ptr, struct etherip_tunnel, list);
Again, please use list_for_each_entry
Quoted 53 lines
net/ipv4/etherip.c +53
-0+if (ret->parms.iph.daddr == p->iph.daddr) { +return ret; + } + } + +return NULL ; +} + +/* find a tunnel by its destination address */ +static struct etherip_tunnel *etherip_tunnel_locate (u32 remote) +{ +struct list_head *ptr; +struct etherip_tunnel *ret; +unsigned h =HASH (remote); + +list_for_each (ptr, &tunnels[h]) { + ret = list_entry(ptr, struct etherip_tunnel, list); +if (ret->parms.iph.daddr == remote) { +return ret; + } + } + +return NULL ; +} + +/* netdevice start function */ +static int etherip_tunnel_open (struct net_device *dev) +{ +netif_start_queue (dev); +return 0 ; +} + +/* netdevice stop function */ +static int etherip_tunnel_stop (struct net_device *dev) +{ +netif_stop_queue (dev); +return 0 ; +} + +/* netdevice hard_start_xmit function +* it gets an Ethernet packet in skb and encapsulates it in another IP +* packet */ +static int etherip_tunnel_xmit (struct sk_buff *skb,struct net_device *dev) +{ +struct etherip_tunnel *tunnel =netdev_priv (dev); +struct rtable *rt; +struct iphdr *iph; +struct flowi fl; +struct net_device *tdev; +int max_headroom; +struct net_device_stats *stats = &tunnel->stats; + +if (tunnel->recursion++) {
net/ipv4/etherip.c line 154
Quoted 10 lines
net/ipv4/etherip.c +10
-0+ tunnel->stats.collisions++; + goto tx_error; + } + + fl.oif = fl.iif =0 ; + fl.proto =IPPROTO_ETHERIP ; + fl.nl_u.ip4_u.daddr = tunnel->parms.iph.daddr; + fl.nl_u.ip4_u.saddr = tunnel->parms.iph.saddr; + fl.nl_u.ip4_u.fwmark =0 ; + fl.nl_u.ip4_u.tos =0 ;
This still leaves the entire uli_u part as well as flags uninitialized. Just use memset or initialize the entire structure at once. fl.oif should be set to parms.link.
Quoted 27 lines
net/ipv4/etherip.c +27
-0+ +if (ip_route_output_key (&rt, &fl)) { + tunnel->stats.tx_carrier_errors++; + goto tx_error_icmp; + } + + tdev = rt->u.dst.dev; +if (tdev == dev) { +ip_rt_put (rt); + tunnel->stats.collisions++; + goto tx_error; + } + + max_headroom = (LL_RESERVED_SPACE (tdev)+sizeof (struct iphdr ) + +ETHERIP_HLEN ); + +if (skb_headroom (skb) < max_headroom ||skb_cloned (skb) + ||skb_shared (skb)) { +struct sk_buff *n_skb =skb_realloc_headroom (skb,max_headroom); +if (!n_skb) { +ip_rt_put (rt); +dev_kfree_skb (skb); + tunnel->stats.tx_dropped++; +return 0 ; + } +if (skb->sk) +skb_set_owner_w (n_skb, skb->sk);
net/ipv4/etherip.c line 191
Quoted 10 lines
net/ipv4/etherip.c +10
-0+dev_kfree_skb (skb); + skb = n_skb; + } + + skb->h.raw = skb->nh.raw; + skb->nh.raw =skb_push (skb,sizeof (struct iphdr )+ETHERIP_HLEN ); +memset (&(IPCB (skb)->opt),0 ,sizeof (IPCB (skb)->opt)); +IPCB (skb)->flags &= ~(IPSKB_XFRM_TUNNEL_SIZE |IPSKB_XFRM_TRANSFORMED | +IPSKB_REROUTED ); +dst_release (skb->dst);
Still no propagation of the pmtu to the original dst_entry.
Quoted 47 lines
net/ipv4/etherip.c +47
-0+ skb->dst = &rt->u.dst; + +/* Build the IP header for the outgoing packet +* +* Note: This driver never sets the DF flag on outgoing packets +* to ensure that the tunnel provides the full Ethernet MTU. +* This behavior guarantees that protocols can be +* encapsulated within the Ethernet packet which do not +* know the concept of a path MTU +*/ + iph = skb->nh.iph; + iph->version =4 ; + iph->ihl =sizeof (struct iphdr )>>2 ; + iph->frag_off =0 ; + iph->protocol =IPPROTO_ETHERIP ; + iph->tos =0 ; + iph->daddr = rt->rt_dst; + iph->saddr = rt->rt_src; + iph->ttl = tunnel->parms.iph.ttl; +if (iph->ttl ==0 ) + iph->ttl =dst_metric (&rt->u.dst,RTAX_HOPLIMIT ); + +/* add the 16bit etherip header after the ip header */ + *((u16 *)(skb->nh.raw +sizeof (struct iphdr ))) =ntohs (ETHERIP_HEADER ); +nf_reset (skb); +IPTUNNEL_XMIT (); + tunnel->dev->trans_start = jiffies; + tunnel->recursion--; + +return 0 ; + +tx_error_icmp: +dst_link_failure (skb); + +tx_error: + tunnel->stats.tx_errors++; +dev_kfree_skb (skb); + tunnel->recursion--; +return 0 ; +} + +/* get statistics callback */ +static struct net_device_stats *etherip_tunnel_stats (struct net_device *dev) +{ +struct etherip_tunnel *ethip =netdev_priv (dev); +return ðip->stats; +}
net/ipv4/etherip.c line 248
Quoted 10 lines
net/ipv4/etherip.c +10
-0+ +/* checks parameters the driver gets from userspace */ +static int etherip_param_check (struct ip_tunnel_parm *p) +{ +if ((p->iph.version !=4 ) + || (p->iph.protocol !=IPPROTO_ETHERIP ) + || (p->iph.ihl !=5 ) + || (p->iph.daddr ==INADDR_ANY ) + ||MULTICAST (p->iph.daddr)) +return -EINVAL ;
Lots of unnecessary parens (here and elsewhere). It also becomes more readable IMO if you put the || at the end of the line and align the conditions:
if (p->iph.version != 4 ||
p->iph.protocol != IPPROTO_ETHERIP ||
p->iph.ihl != 4 ||...
Well, thats just my taste, but a single tab is in my opinion the worst of all choices since it fails to make the distinction between the condition and the following expression visible.
Quoted 16 lines
net/ipv4/etherip.c +16
-0+ +return 0 ; +} + +/* central ioctl function for all netdevices this driver manages +* it allows to create, delete, modify a tunnel and fetch tunnel +* information */ +static int etherip_tunnel_ioctl (struct net_device *dev,struct ifreq *ifr, +int cmd) +{ +int err =0 ; +struct ip_tunnel_parm p; +struct net_device *new_dev; +char *dev_name; +struct etherip_tunnel *t; +
net/ipv4/etherip.c line 274
Quoted 10 lines
net/ipv4/etherip.c +10
-0+ +switch (cmd) { +case SIOCGETTUNNEL : + err = -EINVAL ; +if (dev == etherip_tunnel_dev) + goto out; + t =netdev_priv (dev); +if (copy_to_user (ifr->ifr_ifru.ifru_data, &t->parms, +sizeof (t->parms))) + err = -EFAULT ;
break
Quoted 51 lines
net/ipv4/etherip.c +51
-0+ err =0 ; +break ; +case SIOCADDTUNNEL : + err = -EINVAL ; +if (dev != etherip_tunnel_dev) + goto out; + +case SIOCCHGTUNNEL : + err = -EPERM ; +if (!capable (CAP_NET_ADMIN )) + goto out; + + err = -EFAULT ; +if (copy_from_user (&p, ifr->ifr_ifru.ifru_data, +sizeof (p))) + goto out; + +if ((err =etherip_param_check (&p)) <0 ) + goto out; + + t =etherip_tunnel_find (&p); + + err = -EEXIST ; +if ((t !=NULL ) && (t->dev != dev)) + goto out; + +if (cmd ==SIOCADDTUNNEL ) { + + p.name[IFNAMSIZ -1 ] =0 ; + dev_name = p.name; +if (dev_name[0 ] ==0 ) + dev_name ="ethip%d" ; + + err = -ENOMEM ; + new_dev =alloc_netdev ( +sizeof (struct etherip_tunnel ), + dev_name, + etherip_tunnel_setup); + +if (new_dev ==NULL ) + goto out; + +if (strchr (new_dev->name,'%' )) { + err =dev_alloc_name ( new_dev, new_dev->name); +if (err <0 ) + goto add_err; + } + + t =netdev_priv (new_dev); + t->dev = new_dev; +strncpy (p.name, new_dev->name,IFNAMSIZ );
net/ipv4/etherip.c line 335
Quoted 10 lines
net/ipv4/etherip.c +10
-0+memcpy (&(t->parms), &p,sizeof (p)); + + err =register_netdevice (new_dev); +if (err <0 ) + goto add_err; + + err = -EFAULT ; +if (copy_to_user (ifr->ifr_ifru.ifru_data, &p, +sizeof (p))) + goto add_err;
You can't just free the device once its registered.
net/ipv4/etherip.c line 337
Quoted 2 lines
net/ipv4/etherip.c +2
-0+ +write_lock (ðerip_lock);
Needs bh protection.
Quoted 117 lines
net/ipv4/etherip.c +117
-0+etherip_tunnel_add (t); +write_unlock (ðerip_lock); + + }else { + err = -EINVAL ; +if ((t =netdev_priv (dev)) ==NULL ) + goto out; +if (dev == etherip_tunnel_dev) + goto out; +write_lock (ðerip_lock); +memcpy (&(t->parms), &p,sizeof (p)); +write_unlock (ðerip_lock); + } + + err =0 ; +break ; +add_err: +free_netdev (new_dev); + goto out; + +case SIOCDELTUNNEL : + err = -EPERM ; +if (!capable (CAP_NET_ADMIN )) + goto out; + + err = -EINVAL ; +if (dev == etherip_tunnel_dev) + goto out; + + t =netdev_priv (dev); + +write_lock (ðerip_lock); +etherip_tunnel_del (t); +write_unlock (ðerip_lock); + +unregister_netdevice (t->dev); + err =0 ; + +break ; +default : + err = -EINVAL ; + } + +out: +return err; +} + +/* device init function - called via register_netdevice +* The tunnel is registered as an Ethernet device. This allows +* the tunnel to be added to a bridge */ +static void etherip_tunnel_setup (struct net_device *dev) +{ +SET_MODULE_OWNER (dev); + dev->open = etherip_tunnel_open; + dev->hard_start_xmit = etherip_tunnel_xmit; + dev->stop = etherip_tunnel_stop; + dev->get_stats = etherip_tunnel_stats; + dev->do_ioctl = etherip_tunnel_ioctl; + dev->destructor = free_netdev; + +ether_setup (dev); + dev->tx_queue_len =0 ; +random_ether_addr (dev->dev_addr); +} + +/* receive function for EtherIP packets +* Does some basic checks on the MAC addresses and +* interface modes */ +static int etherip_rcv (struct sk_buff *skb) +{ +struct iphdr *iph; +struct ethhdr *ehdr; +struct etherip_tunnel *tunnel; +struct net_device *dev; + + iph = skb->nh.iph; + +read_lock (ðerip_lock); + tunnel =etherip_tunnel_locate (iph->saddr); +if (tunnel ==NULL ) + goto drop; + + dev = tunnel->dev; +secpath_reset (skb); +memset (&(IPCB (skb)->opt),0 ,sizeof (struct ip_options )); +skb_pull (skb, (skb->nh.raw - skb->data) + +sizeof (struct iphdr ) +ETHERIP_HLEN ); + ehdr = (struct ethhdr *)skb->data; + skb->dev = dev; + skb->pkt_type =PACKET_HOST ; + skb->protocol =eth_type_trans (skb, tunnel->dev); + skb->ip_summed =CHECKSUM_UNNECESSARY ; +dst_release (skb->dst); + skb->dst =NULL ; + +/* do some checks */ +if (skb->pkt_type ==PACKET_HOST || skb->pkt_type ==PACKET_BROADCAST ) + goto accept; + +if (skb->pkt_type ==PACKET_MULTICAST && + (dev->mc_count >0 || dev->flags &IFF_ALLMULTI )) + goto accept; + +if (skb->pkt_type ==PACKET_OTHERHOST && dev->flags &IFF_PROMISC ) + goto accept; + + goto drop; + +accept: + tunnel->dev->last_rx = jiffies; + tunnel->stats.rx_packets++; + tunnel->stats.rx_bytes += skb->len; +nf_reset (skb); +netif_rx (skb); +read_unlock (ðerip_lock); +return 0 ; +
net/ipv4/etherip.c line 464
Quoted 10 lines
net/ipv4/etherip.c +10
-0+drop: +read_unlock (ðerip_lock); +kfree_skb (skb); +return 0 ; +} + +static struct net_protocol etherip_protocol = { + .handler = etherip_rcv, + .err_handler =0 , + .no_policy =1 ,
This is wrong, you don't do any policy checks in your code.
Quoted 82 lines
net/ipv4/etherip.c +82
-0+}; + +/* module init function +* initializes the EtherIP protocol (97) and registers the initial +* device */ +static int __init etherip_init (void ) +{ +int err, i; +struct etherip_tunnel *p; + + printk(KERN_INFO BANNER1); + printk(KERN_INFO BANNER2); + +for (i=0 ;i<HASH_SIZE ;++i) +INIT_LIST_HEAD (&tunnels[i]); + +if (inet_add_protocol (ðerip_protocol,IPPROTO_ETHERIP )) { +printk (KERN_ERR "etherip: can't add protocol\n" ); +return -EAGAIN ; + } + + etherip_tunnel_dev =alloc_netdev (sizeof (struct etherip_tunnel ), +"ethip0" , + etherip_tunnel_setup); + +if (!etherip_tunnel_dev) { + err = -ENOMEM ; + goto err2; + } + + p =netdev_priv (etherip_tunnel_dev); + p->dev = etherip_tunnel_dev; + +if ((err =register_netdev (etherip_tunnel_dev))) + goto err1; + +out: +return err; +err1: +free_netdev (etherip_tunnel_dev); +err2: +inet_del_protocol (ðerip_protocol,IPPROTO_ETHERIP ); + goto out; +} + +/* destroy all tunnels */ +static void __exit etherip_destroy_tunnels(void) +{ +int i; +struct list_head *ptr; +struct etherip_tunnel *tun; + +for (i=0 ;i<HASH_SIZE ;++i) { +/* +ptr = tunnels[i].next; +while (ptr != &(tunnels[i])) { +ret = list_entry(ptr, struct etherip_tunnel, list); +ptr = ptr->next; +unregister_netdevice(ret->dev); +}*/ +list_for_each (ptr, &tunnels[i]) { + tun = list_entry(ptr, struct etherip_tunnel, list); + ptr = ptr->prev; +etherip_tunnel_del (tun); +unregister_netdevice (tun->dev); + } + } +} + +/* module cleanup function */ +static void __exit etherip_exit(void) +{ +rtnl_lock (); +etherip_destroy_tunnels (); +unregister_netdevice (etherip_tunnel_dev); +rtnl_unlock (); +if (inet_del_protocol (ðerip_protocol,IPPROTO_ETHERIP )) +printk (KERN_ERR "etherip: can't remove protocol\n" ); +} + +module_init (etherip_init); +module_exit (etherip_exit);
net/ipv4/Kconfig config NET_IPGRE_BROADCAST · line 287
Quoted 3 lines · Joerg Roedel
net/ipv4/Kconfig +3
-0+ To configure tunnels an extra tool is required. You can download + it from http://zlug.fh-zwickau.de/~joro/projects/ under the + EtherIP section. If unsure, say N.
To obtain a list of tunnels, this tool calls SIOCGETTUNNEL (SIOCDEVPRIVATE + 0) for every device in /proc/net/dev. I don't think this is safe, but I don't have a solution for you.
Is there a reason why you have a separate tool rather than modifying iproute2?
I don't know if you are aware of this older etherip patch by Lennert
Buytenhek: http://www.wantstofly.org/~buytenh/etherip/
Quoted 9 lines · On Thu, 14 Sep 2006 11:21:22 +1000 Philip Craig <[email protected]> wrote:
net/ipv4/Kconfig config NET_IPGRE_BROADCAST · line 287
Quoted 3 lines · Joerg Roedel
net/ipv4/Kconfig +3
-0+ To configure tunnels an extra tool is required. You can download + it from http://zlug.fh-zwickau.de/~joro/projects/ under the + EtherIP section. If unsure, say N.To obtain a list of tunnels, this tool calls SIOCGETTUNNEL (SIOCDEVPRIVATE + 0) for every device in
/proc/net/dev. I don't think this is safe, but I don't have a solution for you.
Quoted 5 lines
Is there a reason why you have a separate tool rather than modifying iproute2?
I don't know if you are aware of this older etherip patch by Lennert
Buytenhek: http://www.wantstofly.org/~buytenh/etherip/
SIOCDEVPRIVATE usage makes it hard to do 32 bit compatibility layer.
Quoted 8 lines · Philip Craig
net/ipv4/Kconfig config NET_IPGRE_BROADCAST · line 287
Quoted 3 lines · Joerg Roedel
net/ipv4/Kconfig +3
-0+ To configure tunnels an extra tool is required. You can download + it from http://zlug.fh-zwickau.de/~joro/projects/ under the + EtherIP section. If unsure, say N.To obtain a list of tunnels, this tool calls SIOCGETTUNNEL (SIOCDEVPRIVATE + 0) for every device in
/proc/net/dev. I don't think this is safe, but I don't have a solution for you.
You are right. But this is the way the ipip driver does it. In the case of ipip it is safe, because it is visible as a tunnel interface to userspace. But my driver registers its devices as Ethernet (it has to, otherwise the devices will not be usable in a bridge). There is no safe way to distinguish between real Ethernet devices and devices registered by my driver. I think about implementing an ioctl to fetch a list of all EtherIP tunnel devices from the driver.
Quoted 2 lines
Is there a reason why you have a separate tool rather than modifying iproute2?
I wrote an own tool for testing. At development I wanted to concentrate on the driver and not how to modify iproute2. But when the driver becomes stable and may be included I will add it to iproute2.
Quoted 2 lines
I don't know if you are aware of this older etherip patch by Lennert
Buytenhek: http://www.wantstofly.org/~buytenh/etherip/
I found this patch after I wrote my own and read the discussions about it. The patch by Lennert Buytenhek has the same problem of identifing tunnel devices. Futhermore, his driver handles ICMP and cares about the payload of the Ethernet packet it transmits (it looks, if the payload ist IPv4 or IPv6). Further it is configurable to set the DF flag in outgoing packets. First I think the handling of layer 3 protocols is beyond the scope of tunnel which transmits layer 2 packets. Second this behavior may break the transport of non-IP payload in the Ethernet packets since the Ethernet payload protocol may not know the concept of a path MTU and needs the full Ethernet MTU of 1500. This is the reason my driver never sets the DF flag in outgoing packets.
Regards,
Joerg Roedel
Quoted 13 lines · Joerg Roedel
Quoted 9 lines · Philip Craig
net/ipv4/Kconfig config NET_IPGRE_BROADCAST · line 287
Quoted 3 lines · Joerg Roedel
net/ipv4/Kconfig +3
-0+ To configure tunnels an extra tool is required. You can download + it from http://zlug.fh-zwickau.de/~joro/projects/ under the + EtherIP section. If unsure, say N.To obtain a list of tunnels, this tool calls SIOCGETTUNNEL (SIOCDEVPRIVATE + 0) for every device in
/proc/net/dev. I don't think this is safe, but I don't have a solution for you.
Quoted 7 lines
You are right. But this is the way the ipip driver does it. In the case of ipip it is safe, because it is visible as a tunnel interface to userspace. But my driver registers its devices as Ethernet (it has to, otherwise the devices will not be usable in a bridge). There is no safe way to distinguish between real Ethernet devices and devices registered by my driver. I think about implementing an ioctl to fetch a list of all EtherIP tunnel devices from the driver.
Just do what ipip and gre do, use a network device with a fixed name for the ioctl (you already have the ethip0 device for this purpose it appears).
Quoted 7 lines
Quoted 2 lines
Is there a reason why you have a separate tool rather than modifying iproute2?
I wrote an own tool for testing. At development I wanted to concentrate on the driver and not how to modify iproute2. But when the driver becomes stable and may be included I will add it to iproute2.
The iproute changes are only a few lines, just add the ethip0 device to the do_add, do_del, ... commands and set the protocol to IPPROTO_ETHERIP when an etherip tunnel is requested.
Quoted 21 lines · Patrick McHardy
Quoted 11 lines · Joerg Roedel
Quoted 8 lines · Philip Craig
net/ipv4/Kconfig config NET_IPGRE_BROADCAST · line 287
Quoted 3 lines · Joerg Roedel
net/ipv4/Kconfig +3
-0+ To configure tunnels an extra tool is required. You can download + it from http://zlug.fh-zwickau.de/~joro/projects/ under the + EtherIP section. If unsure, say N.To obtain a list of tunnels, this tool calls SIOCGETTUNNEL (SIOCDEVPRIVATE + 0) for every device in
/proc/net/dev. I don't think this is safe, but I don't have a solution for you.Quoted 7 lines
You are right. But this is the way the ipip driver does it. In the case of ipip it is safe, because it is visible as a tunnel interface to userspace. But my driver registers its devices as Ethernet (it has to, otherwise the devices will not be usable in a bridge). There is no safe way to distinguish between real Ethernet devices and devices registered by my driver. I think about implementing an ioctl to fetch a list of all EtherIP tunnel devices from the driver.
Quoted 3 lines
Just do what ipip and gre do, use a network device with a fixed name for the ioctl (you already have the ethip0 device for this purpose it appears).
That fixed name device isn't used to get a list of tunnels. Instead, ipip and gre read /proc/net/dev, and check for ARPHRD_TUNNEL or ARPHRD_IPGRE. This won't work for etherip because it uses ARPHRD_ETHER, which isn't specific to etherip tunnels. A new ioctl to get a list could be added (this ioctl would use the fixed name device), is that acceptable?
Quoted 26 lines · Philip Craig
Quoted 21 lines · Patrick McHardy
Quoted 11 lines · Joerg Roedel
Quoted 8 lines · Philip Craig
net/ipv4/Kconfig config NET_IPGRE_BROADCAST · line 287
Quoted 3 lines · Joerg Roedel
net/ipv4/Kconfig +3
-0+ To configure tunnels an extra tool is required. You can download + it from http://zlug.fh-zwickau.de/~joro/projects/ under the + EtherIP section. If unsure, say N.To obtain a list of tunnels, this tool calls SIOCGETTUNNEL (SIOCDEVPRIVATE + 0) for every device in
/proc/net/dev. I don't think this is safe, but I don't have a solution for you.Quoted 7 lines
You are right. But this is the way the ipip driver does it. In the case of ipip it is safe, because it is visible as a tunnel interface to userspace. But my driver registers its devices as Ethernet (it has to, otherwise the devices will not be usable in a bridge). There is no safe way to distinguish between real Ethernet devices and devices registered by my driver. I think about implementing an ioctl to fetch a list of all EtherIP tunnel devices from the driver.
Quoted 3 lines
Just do what ipip and gre do, use a network device with a fixed name for the ioctl (you already have the ethip0 device for this purpose it appears).
Quoted 5 lines
That fixed name device isn't used to get a list of tunnels. Instead, ipip and gre read
/proc/net/dev, and check forARPHRD_TUNNELorARPHRD_IPGRE. This won't work for etherip because it usesARPHRD_ETHER, which isn't specific to etherip tunnels. A new ioctl to get a list could be added (this ioctl would use the fixed name device), is that acceptable?
The problem is that the ethip0 device also uses ARPHDR_ETHER. The usage of that device is also unsafe. As I see the situation there are 2 solutions for this problem. First use some other Type identifier for ethip0. But this is only a quick hack. I think about a new device type ARPHRD_ETHERIP. This makes the tunnel devices incompatible with the bridging code. But I think it is possible to convince the bridge code to accept the special tunnel devices too.
Unfortunately I didn't saw the problem when implementing the driver...
Regards,
Joerg Roedel
Quoted 2 lines · Joerg Roedel
This driver implements the tunneling of Ethernet packets over IPv4 networks for Linux. It uses the protocol defined in RFC 3378.
Check out the thread "[PATCH][RFC] etherip: Ethernet-in-IPv4 tunneling" that was on netdev in January of 2005 -- a number of arguments against etherip (and for tunneling ethernet in GRE) were raised back then.
One of the most significant ones, IMHO:
Quoted 5 lines
Another argument against etherip would be that OpenBSD apparently mis-implemented etherip by putting the etherip version nibble in the second nibble of the etherip header instead of the first, which would probably prevent the linux and OpenBSD versions from interoperating, negating the advantage of using etherip in the first place.
cheers,
Lennert
Quoted 3 lines · Lennert Buytenhek
Check out the thread "[PATCH][RFC] etherip: Ethernet-in-IPv4 tunneling" that was on netdev in January of 2005 -- a number of arguments against etherip (and for tunneling ethernet in GRE) were raised back then.
I read this thread some weeks ago. I think there are reasons to have both variants in the kernel. Since both versions are implemented in different operatins systems and devices, having both will Linux make interoperable with all of them. In fact, the only implementers for EtherIP I found were various BSD derivates. I actually implemented this driver upon request of a BSD user who wanted interoperability of the NetBSD EtherIP implementation with Linux.
Quoted 8 lines
One of the most significant ones, IMHO:
Quoted 5 lines
Another argument against etherip would be that OpenBSD apparently mis-implemented etherip by putting the etherip version nibble in the second nibble of the etherip header instead of the first, which would probably prevent the linux and OpenBSD versions from interoperating, negating the advantage of using etherip in the first place.
I think this is not really a mistake in the OpenBSD implementation. In my opinion, the RFC is unclear at this point. I focused on interoperability in my implementation and did it the same way as OpenBSD (as NetBSD does also, AFAIK FreeBSD has also an EtherIP implementation,
but I don't tested it). This is the reason why my driver does not check
the value of the incoming EtherIP header too.
Regards,
Joerg Roedel