Skip to contentSkip to conversation

Can't get it working on Mobile Coppermine 1Ghz - i440BX - please help...

DISCUSSION Johny the Ripper 3 participants 5 messages Sep 13, 2006 – Sep 14, 2006

lore
Share & tools
lore
#0 lore raw

I started a thread on the gentoo forums, but I didn't get a reply... I hope you guys can help me out, I searched the internet and forums a lot, don't know why it isn't working... Here's the gentoo thread:

http://forums.gentoo.org/viewtopic-t-497427.html

If you have a clue of where I could begin to continue to search, please post it...

thx

__________________________________________________
Do You Yahoo!?
Tired of spam? Yahoo! Mail has the best spam protection around
http://mail.yahoo.com

#1 lore raw
Quoted 10 lines · Johny the Ripper

I started a thread on the gentoo forums, but I didn't get a reply... I hope you guys can help me out, I searched the internet and forums a lot, don't know why it isn't working... Here's the gentoo thread:

http://forums.gentoo.org/viewtopic-t-497427.html

If you have a clue of where I could begin to continue to search, please post it...

http://www.poupinou.org/cpufreq/

Perhaps doing something like that:

modprobe speedstep-smi smi_port=0xb2 smi_cmd=0x82 smi_sig=1 will help resolve that issue?

If that don't work, please provide output from speedstep-detect that can be found here:
ftp://ftp.poupinou.org/cpufreq/speedstep-detect.tar.gz

Cheers,

Signature · 4 lines
Bruno Ducrot

--  Which is worse:  ignorance or apathy?
--  Don't know.  Don't care.
#2 lore raw

Same problem for me:
I have a 700MHz Mobile Coppermine on i440BX

Quoted 1 line
Quoted 1 line

http://forums.gentoo.org/viewtopic-t-497427.html

my /proc/cpuinfo differs only in:
stepping : 6
cpu MHz : 697.028
bogomips : 1395.44

I'm running Debian sid with kernel 2.6.17. Here is uname -a :
Linux rzm-lohner-lt 2.6.17-2-686 #1 SMP Thu Aug 31 12:53:18 UTC 2006 i686 GNU/Linux

Everything necessery for speedstep should be enabled in the kernel config in my opinion.

Quoted 10 lines
Quoted 3 lines

If you have a clue of where I could begin to continue to search, please post it...

http://www.poupinou.org/cpufreq/

Perhaps doing something like that:

modprobe speedstep-smi smi_port=0xb2 smi_cmd=0x82 smi_sig=1 will help resolve that issue?

trying: modprobe speedstep-smi smi_port=0xb2 smi_cmd=0x82 smi_sig=1
gives:
FATAL: Error inserting speedstep_smi (/lib/modules/2.6.17-2-686/kernel/arch/i386/kernel/cpu/cpufreq/speedstep-smi.ko): No such device

Quoted 4 lines

If that don't work, please provide output from speedstep-detect that can be found here:
ftp://ftp.poupinou.org/cpufreq/speedstep-detect.tar.gz

I'll send the output of speedstep-detect to Bruno in a second...

Rudolf

Signature · 5 lines
Rudolf Lohner  -  Universitaet Karlsruhe (TH)
Rechenzentrum,  Zirkel 2,   D-76128 Karlsruhe
Phone: +49-721-608-6958,   Fax: +49-721-32550
E-Mail:     [email protected]
http://www.rz.uni-karlsruhe.de/~Rudolf.Lohner
#3 lore raw

Hi,

Thank you Bruno, with the module params you specified I have it running now :)
However, it still doesn't do everything I wanted, but I suspect this has to do with hardware limitations... My goal was to use the "ondemand" governor, but I cannot start it. I can set the frequency manually and load the powersave, performance and userspace governors -- but not the ondemand governor :( Is this normal?

For Rudolf: I have seen this error too. With me it occurs when you have set the speedstep setting in your bios to "disabled". I have 4 options in my bios for speedstep (max performance, battery optimized, auto and disabled) and selected "auto". The module should then load fine.

greetz,
Johny

--- Rudolf Lohner <[email protected]>

Quoted 27 lines · wrote:

Same problem for me:
I have a 700MHz Mobile Coppermine on i440BX

Quoted 1 line
Quoted 1 line

http://forums.gentoo.org/viewtopic-t-497427.html

my /proc/cpuinfo differs only in:
stepping : 6
cpu MHz : 697.028
bogomips : 1395.44

I'm running Debian sid with kernel 2.6.17. Here is uname -a :
Linux rzm-lohner-lt 2.6.17-2-686 #1 SMP Thu Aug 31 12:53:18 UTC 2006 i686 GNU/Linux

Everything necessery for speedstep should be enabled in the
kernel config in my opinion.

Quoted 1 line
Quoted 1 line

If you have a clue of where I could begin to

continue

Quoted 7 lines
Quoted 2 lines

to search, please post it...

http://www.poupinou.org/cpufreq/

Perhaps doing something like that:

Quoted 9 lines
Quoted 1 line

modprobe speedstep-smi smi_port=0xb2 smi_cmd=0x82

smi_sig=1

Quoted 1 line

will help resolve that issue?

trying: modprobe speedstep-smi smi_port=0xb2
smi_cmd=0x82 smi_sig=1
gives:
FATAL: Error inserting speedstep_smi

(/lib/modules/2.6.17-2-686/kernel/arch/i386/kernel/cpu/cpufreq/speedstep-smi.ko):

Quoted 8 lines

No such device

Quoted 2 lines

If that don't work, please provide output from

speedstep-detect

Quoted 2 lines

that can be found here:

ftp://ftp.poupinou.org/cpufreq/speedstep-detect.tar.gz

Quoted 13 lines

I'll send the output of speedstep-detect to Bruno in a second...

Rudolf

Signature · 5 lines
Rudolf Lohner  -  Universitaet Karlsruhe (TH)
Rechenzentrum,  Zirkel 2,   D-76128 Karlsruhe
Phone: +49-721-608-6958,   Fax: +49-721-32550
E-Mail:     [email protected]
http://www.rz.uni-karlsruhe.de/~Rudolf.Lohner

__________________________________________________
Do You Yahoo!?
Tired of spam? Yahoo! Mail has the best spam protection around
http://mail.yahoo.com

#4 lore raw
Quoted 12 lines · Johny the Ripper

Hi,

Thank you Bruno, with the module params you specified I have it running now :)
However, it still doesn't do everything I wanted, but I suspect this has to do with hardware limitations... My goal was to use the "ondemand" governor, but I cannot start it. I can set the frequency manually and load the powersave, performance and userspace governors -- but not the ondemand governor :( Is this normal?

Yes. The problem with speedstep smi is that we don't know exactly how much time at transition will take. I've see some mail about adding such information for that driver, but nothing reach mainstream AFAIK.

More precisely, you have to modify that line:

	policy->cpuinfo.transition_latency = CPUFREQ_ETERNAL;

with something like that:

	policy->cpuinfo.transition_latency = 100000;

Actually I *really* don't know if that's correct, but it should be close enough to the real one, hopefully, even though I don't count the bus stuff, memory cache invalidation and so on..

Quoted 6 lines

For Rudolf: I have seen this error too. With me it occurs when you have set the speedstep setting in your bios to "disabled". I have 4 options in my bios for speedstep (max performance, battery optimized, auto and disabled) and selected "auto". The module should then load fine.

Ah yes. I always forget that issue :)

Signature · 4 lines
Bruno Ducrot

--  Which is worse:  ignorance or apathy?
--  Don't know.  Don't care.