Skip to contentSkip to conversation

"Int 6: CR2" on bootup w/ 2.6.18-rc7-mm1

DISCUSSION Bernhard Rosenkraenzer 4 participants 4 messages Sep 21, 2006

lore
Share & tools
lore
#0 lore raw

This happens when trying to boot 2.6.18-rc7-mm1 on a truly ancient (Pentium 1) box:

Uncompressing Linux... Ok, booting the kernel.

Int 6: CR2 00000000 err 00000000 EIP c0381719 CS 00000060 flags 00010046

Stack: 00000000 c036f4d1 00000000 c0100199 000001b8 0505c600 00c036cc 001f0fc3

(No further details even with initcall_debug loglevel=7). c0381719 appears to be in ACPI code -- but the Int 6 error happens even with acpi=off.

#1 lore raw
Quoted 11 lines · On Thu, 21 Sep 2006 14:12:08 +0200 Bernhard Rosenkraenzer <[email protected]>…

This happens when trying to boot 2.6.18-rc7-mm1 on a truly ancient (Pentium 1) box:

Uncompressing Linux... Ok, booting the kernel.

Int 6: CR2 00000000 err 00000000 EIP c0381719 CS 00000060 flags 00010046

Stack: 00000000 c036f4d1 00000000 c0100199 000001b8 0505c600 00c036cc 001f0fc3

(No further details even with initcall_debug loglevel=7). c0381719 appears to be in ACPI code -- but the Int 6 error happens even with acpi=off.

Well Chuck's new early-fault handler has gone and handled an early fault.

I assume that machine runs 2.6.18 OK with the same .config?

#2 lore raw
Quoted 13 lines · Andrew Morton
Quoted 8 lines · On Thu, 21 Sep 2006 14:12:08 +0200 Bernhard Rosenkraenzer <[email protected]>…

This happens when trying to boot 2.6.18-rc7-mm1 on a truly ancient (Pentium 1)
box:

Uncompressing Linux... Ok, booting the kernel.

Int 6: CR2 00000000 err 00000000 EIP c0381719 CS 00000060 flags 00010046

Stack: 00000000 c036f4d1 00000000 c0100199 000001b8 0505c600 00c036cc

001f0fc3

Quoted 1 line
Quoted 8 lines
Quoted 3 lines

(No further details even with initcall_debug loglevel=7). c0381719 appears to be in ACPI code -- but the Int 6 error happens even with acpi=off.

Well Chuck's new early-fault handler has gone and handled an early fault.

I assume that machine runs 2.6.18 OK with the same .config? -

Interrupt 6 is an invalid opcode interrupt. The caller might check the kind of CPU for which the kernel was compiled. You can't boot a '486 with '686 opcodes. "Truly ancient" probably explains it all.

Cheers,
Dick Johnson
Penguin : Linux version 2.6.16.24 on an i686 machine (5592.66 BogoMips). New book: http://www.AbominableFirebug.com/
_


****************************************************************
The information transmitted in this message is confidential and may be privileged. Any review, retransmission, dissemination, or other use of this information by persons or entities other than the intended recipient is prohibited. If you are not the intended recipient, please notify Analogic Corporation immediately - by replying to this message or by sending an email to [email protected] - and destroy all copies of this information, including any attachments, without reading or disclosing them.

Thank you.

#3 lore raw
In reply to Andrew Morton
Quoted 11 lines · Andrew Morton
Quoted 8 lines · On Thu, 21 Sep 2006 14:12:08 +0200 Bernhard Rosenkraenzer <[email protected]>…

This happens when trying to boot 2.6.18-rc7-mm1 on a truly ancient (Pentium 1) box:

Uncompressing Linux... Ok, booting the kernel.

Int 6: CR2 00000000 err 00000000 EIP c0381719 CS 00000060 flags 00010046

Stack: 00000000 c036f4d1 00000000 c0100199 000001b8 0505c600 00c036cc 001f0fc3
Quoted 7 lines
Quoted 3 lines

(No further details even with initcall_debug loglevel=7). c0381719 appears to be in ACPI code -- but the Int 6 error happens even with acpi=off.

Well Chuck's new early-fault handler has gone and handled an early fault.

I assume that machine runs 2.6.18 OK with the same .config?

Int 6 is invalid op. Can you do

gdb vmlinux
disassemble 0x<number behind EIP>?

and send the full output?

-Andi