Add mpc8272ads to powerpc
Subsystems (2)
cover Add mpc8272ads to powerpc
The following series adds support for the Freescale mpc8272ads board under arch/powerpc. Assuming 8560 series applied.
Relevant patches are also available in git:/git.kernel.org/pub/scm/linux/kernel/git/vitb/linux-2.6-PQ.git in testing branch.
--
Sincerely, Vitaly
PATCH 1/3 POWERPC: Added devicetree for mpc8272ads board
This adds current dts file used with MPC8272ADS,
introducing new mdio bitbang defines, as well as
fully-CPM2-SoC board design.
---
arch/powerpc/boot/dts/mpc8272ads.dts | 236 ++++++++++++++++++++++++++++++++++ 1 files changed, 236 insertions(+), 0 deletions(-)
arch/powerpc/boot/dts/mpc8272ads.dts new file +236 -0
@@ -0,0 +1,236 @@ +/* + * MPC8272 ADS Device Tree Source + * + * Copyright 2005 Freescale Semiconductor Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + + +/* +/memreserve/ 00000000 4000000; +*/ + +/ { + model = "MPC8272ADS"; + compatible = "MPC8260ADS"; + #address-cells = <1>; + #size-cells = <1>; + linux,phandle = <100>; + + cpus { + #cpus = <1>; + #address-cells = <1>; + #size-cells = <0>; + linux,phandle = <200>; + + PowerPC,8272@0 { + device_type = "cpu"; + reg = <0>; + d-cache-line-size = <20>; // 32 bytes + i-cache-line-size = <20>; // 32 bytes + d-cache-size = <4000>; // L1, 16K + i-cache-size = <4000>; // L1, 16K + timebase-frequency = <17d7840>; + bus-frequency = <5f5e100>; + clock-frequency = <17D78400>; + 32-bit; + linux,phandle = <201>; + linux,boot-cpu; + }; + }; + + interrupt-controller@f8200000 { + linux,phandle = <f8200000>; + #address-cells = <0>; + #interrupt-cells = <2>; + interrupt-controller; + reg = <f8200000 f8200004>; + built-in; + device_type = "pci-pic"; + }; + memory { + device_type = "memory"; + linux,phandle = <300>; + reg = <00000000 4000000 f4500000 00000020>; + }; + + chosen { + name = "chosen"; + bootargs = "root=/dev/nfs rw ip=on"; + linux,stdout-path = "/dev/ttyCPM0"; + linux,platform = <0>; + interrupt-controller = <10c00>; + linux,phandle = <400>; + }; + + soc8272@f0000000 { + #address-cells = <1>; + #size-cells = <1>; + #interrupt-cells = <2>; + device_type = "soc"; + ranges = < 0 0 2 00000000 f0000000 00053000>; + reg = <f0000000 0>; + + mdio@0 { + device_type = "mdio"; + compatible = "fs_enet"; + reg = <0 0>; + linux,phandle = <24520>; + #address-cells = <1>; + #size-cells = <0>; + ethernet-phy@0 { + linux,phandle = <2452000>; + interrupt-parent = <10c00>; + interrupts = <19 1>; + reg = <0>; + bitbang = [ 12 12 13 02 02 01 ]; + device_type = "ethernet-phy"; + }; + ethernet-phy@1 { + linux,phandle = <2452001>; + interrupt-parent = <10c00>; + interrupts = <19 1>; + bitbang = [ 12 12 13 02 02 01 ]; + reg = <3>; + device_type = "ethernet-phy"; + }; + }; + + ethernet@24000 { + #address-cells = <1>; + #size-cells = <0>; + device_type = "network"; + device-id = <2>; + compatible = "fs_enet"; + model = "FCC"; + reg = <11300 20 8400 100 11380 30>; + mac-address = [ 00 11 2F 99 43 54 ]; + interrupts = <20 2>; + interrupt-parent = <10c00>; + phy-handle = <2452000>; + rx-clock = <13>; + tx-clock = <12>; + }; + + ethernet@25000 { + device_type = "network"; + device-id = <3>; + compatible = "fs_enet"; + model = "FCC"; + reg = <11320 20 8500 100 113b0 30>; + mac-address = [ 00 11 2F 99 44 54 ]; + interrupts = <21 2>; + interrupt-parent = <10c00>; + phy-handle = <2452001>; + rx-clock = <17>; + tx-clock = <18>; + }; + + cpm@f0000000 { + linux,phandle = <f0000000>; + #address-cells = <1>; + #size-cells = <1>; + #interrupt-cells = <2>; + device_type = "cpm"; + model = "CPM2"; + ranges = <00000000 00000000 3ffff>; + reg = <10d80 3280>; + command-proc = <119c0>; + brg-frequency = <17D7840>; + cpm_clk = <BEBC200>; + + scc@11a00 { + device_type = "serial"; + compatible = "cpm_uart"; + model = "SCC"; + device-id = <2>; + reg = <11a00 20 8000 100>; + current-speed = <1c200>; + interrupts = <28 2>; + interrupt-parent = <10c00>; + clock-setup = <0 00ffffff>; + rx-clock = <1>; + tx-clock = <1>; + }; + + scc@11a60 { + device_type = "serial"; + compatible = "cpm_uart"; + model = "SCC"; + device-id = <5>; + reg = <11a60 20 8300 100>; + current-speed = <1c200>; + interrupts = <2b 2>; + interrupt-parent = <10c00>; + clock-setup = <1b ffffff00>; + rx-clock = <4>; + tx-clock = <4>; + }; + + }; + interrupt-controller@10c00 { + linux,phandle = <10c00>; + #address-cells = <0>; + #interrupt-cells = <2>; + interrupt-controller; + reg = <10c00 80>; + built-in; + device_type = "cpm-pic"; + }; + pci@0500 { + linux,phandle = <0500>; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + compatible = "8272"; + device_type = "pci"; + reg = <10430 4dc>; + clock-frequency = <3f940aa>; + interrupt-map-mask = <f800 0 0 7>; + interrupt-map = < + + /* IDSEL 0x16 */ + b000 0 0 1 f8200000 40 0 + b000 0 0 2 f8200000 41 0 + b000 0 0 3 f8200000 42 0 + b000 0 0 4 f8200000 43 0 + + /* IDSEL 0x17 */ + b800 0 0 1 f8200000 43 0 + b800 0 0 2 f8200000 40 0 + b800 0 0 3 f8200000 41 0 + b800 0 0 4 f8200000 42 0 + + /* IDSEL 0x18 */ + c000 0 0 1 f8200000 42 0 + c000 0 0 2 f8200000 43 0 + c000 0 0 3 f8200000 40 0 + c000 0 0 4 f8200000 41 0>; + interrupt-parent = <10c00>; + interrupts = <14 3>; + bus-range = <0 0>; + ranges = <02000000 0 80000000 80000000 0 40000000 + 01000000 0 00000000 f6000000 0 02000000>; + }; + +/* May need to remove if on a part without crypto engine */ + crypto@30000 { + device_type = "crypto"; + model = "SEC2"; + compatible = "talitos"; + reg = <30000 10000>; + interrupts = <b 0>; + interrupt-parent = <10c00>; + num-channels = <4>; + channel-fifo-len = <18>; + exec-units-mask = <0000007e>; +/* desc mask is for rev1.x, we need runtime fixup for >=2.x */ + descriptor-types-mask = <01010ebf>; + }; + + }; +};
Re: [PATCH 1/3] POWERPC: Added devicetree for mpc8272ads board
Quoted 31 lines · Vitaly Bordug
This adds current dts file used with MPC8272ADS,
introducing new mdio bitbang defines, as well as
fully-CPM2-SoC board design.Signed-off-by Vitaly Bordug <[email protected]>---
arch/powerpc/boot/dts/mpc8272ads.dts | 236 +++++++++++++++++++++++ +++++++++++ 1 files changed, 236 insertions(+), 0 deletions(-)arch/powerpc/boot/dts/mpc8272ads.dts new file +6
-0@@ -0,0 +1,236 @@ +/* + * MPC8272 ADS Device Tree Source + * + * Copyright 2005 Freescale Semiconductor Inc. + * + * This program is free software; you can redistribute it and/ormodify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
arch/powerpc/boot/dts/mpc8272ads.dts line 15
Quoted 5 lines
arch/powerpc/boot/dts/mpc8272ads.dts new file +5
-0+ + +/* +/memreserve/ 00000000 4000000; +*/
Is this needed?
Quoted 14 lines
arch/powerpc/boot/dts/mpc8272ads.dts new file +14
-0+ +/ { + model = "MPC8272ADS"; + compatible = "MPC8260ADS"; + #address-cells = <1>; + #size-cells = <1>; + linux,phandle = <100>; + + cpus { + #cpus = <1>; + #address-cells = <1>; + #size-cells = <0>; + linux,phandle = <200>; +
arch/powerpc/boot/dts/mpc8272ads.dts line 39
Quoted 10 lines
arch/powerpc/boot/dts/mpc8272ads.dts new file +10
-0+ PowerPC,8272@0 { + device_type = "cpu"; + reg = <0>; + d-cache-line-size = <20>; // 32 bytes + i-cache-line-size = <20>; // 32 bytes + d-cache-size = <4000>; // L1, 16K + i-cache-size = <4000>; // L1, 16K + timebase-frequency = <17d7840>; + bus-frequency = <5f5e100>; + clock-frequency = <17D78400>;
Are the freq's really fixed? if not having these values as 0, maybe be better.
Quoted 14 lines
arch/powerpc/boot/dts/mpc8272ads.dts new file +14
-0+ 32-bit; + linux,phandle = <201>; + linux,boot-cpu; + }; + }; + + interrupt-controller@f8200000 { + linux,phandle = <f8200000>; + #address-cells = <0>; + #interrupt-cells = <2>; + interrupt-controller; + reg = <f8200000 f8200004>; + built-in; + device_type = "pci-pic";
arch/powerpc/boot/dts/mpc8272ads.dts line 63
Quoted 10 lines
arch/powerpc/boot/dts/mpc8272ads.dts new file +10
-0+ }; + memory { + device_type = "memory"; + linux,phandle = <300>; + reg = <00000000 4000000 f4500000 00000020>; + }; + + chosen { + name = "chosen"; + bootargs = "root=/dev/nfs rw ip=on";
Seems bad form to put bootargs in the .dts directly like this.
Quoted 1 line
+ linux,stdout-path = "
/dev/ttyCPM0";
I thought this was the 'of' path, not a dev path.
Quoted 109 lines
arch/powerpc/boot/dts/mpc8272ads.dts new file +109
-0+ linux,platform = <0>; + interrupt-controller = <10c00>; + linux,phandle = <400>; + }; + + soc8272@f0000000 { + #address-cells = <1>; + #size-cells = <1>; + #interrupt-cells = <2>; + device_type = "soc"; + ranges = < 0 0 2 00000000 f0000000 00053000>; + reg = <f0000000 0>; + + mdio@0 { + device_type = "mdio"; + compatible = "fs_enet"; + reg = <0 0>; + linux,phandle = <24520>; + #address-cells = <1>; + #size-cells = <0>; + ethernet-phy@0 { + linux,phandle = <2452000>; + interrupt-parent = <10c00>; + interrupts = <19 1>; + reg = <0>; + bitbang = [ 12 12 13 02 02 01 ]; + device_type = "ethernet-phy"; + }; + ethernet-phy@1 { + linux,phandle = <2452001>; + interrupt-parent = <10c00>; + interrupts = <19 1>; + bitbang = [ 12 12 13 02 02 01 ]; + reg = <3>; + device_type = "ethernet-phy"; + }; + }; + + ethernet@24000 { + #address-cells = <1>; + #size-cells = <0>; + device_type = "network"; + device-id = <2>; + compatible = "fs_enet"; + model = "FCC"; + reg = <11300 20 8400 100 11380 30>; + mac-address = [ 00 11 2F 99 43 54 ]; + interrupts = <20 2>; + interrupt-parent = <10c00>; + phy-handle = <2452000>; + rx-clock = <13>; + tx-clock = <12>; + }; + + ethernet@25000 { + device_type = "network"; + device-id = <3>; + compatible = "fs_enet"; + model = "FCC"; + reg = <11320 20 8500 100 113b0 30>; + mac-address = [ 00 11 2F 99 44 54 ]; + interrupts = <21 2>; + interrupt-parent = <10c00>; + phy-handle = <2452001>; + rx-clock = <17>; + tx-clock = <18>; + }; + + cpm@f0000000 { + linux,phandle = <f0000000>; + #address-cells = <1>; + #size-cells = <1>; + #interrupt-cells = <2>; + device_type = "cpm"; + model = "CPM2"; + ranges = <00000000 00000000 3ffff>; + reg = <10d80 3280>; + command-proc = <119c0>; + brg-frequency = <17D7840>; + cpm_clk = <BEBC200>; + + scc@11a00 { + device_type = "serial"; + compatible = "cpm_uart"; + model = "SCC"; + device-id = <2>; + reg = <11a00 20 8000 100>; + current-speed = <1c200>; + interrupts = <28 2>; + interrupt-parent = <10c00>; + clock-setup = <0 00ffffff>; + rx-clock = <1>; + tx-clock = <1>; + }; + + scc@11a60 { + device_type = "serial"; + compatible = "cpm_uart"; + model = "SCC"; + device-id = <5>; + reg = <11a60 20 8300 100>; + current-speed = <1c200>; + interrupts = <2b 2>; + interrupt-parent = <10c00>; + clock-setup = <1b ffffff00>; + rx-clock = <4>; + tx-clock = <4>; + }; +
arch/powerpc/boot/dts/mpc8272ads.dts line 183
Quoted 10 lines
arch/powerpc/boot/dts/mpc8272ads.dts new file +10
-0+ }; + interrupt-controller@10c00 { + linux,phandle = <10c00>; + #address-cells = <0>; + #interrupt-cells = <2>; + interrupt-controller; + reg = <10c00 80>; + built-in; + device_type = "cpm-pic"; + };
Do we need to distinguish cpm2-pic from cpm-pic (8xx)?
Quoted 55 lines
arch/powerpc/boot/dts/mpc8272ads.dts new file +33
-0+ pci@0500 { + linux,phandle = <0500>; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + compatible = "8272"; + device_type = "pci"; + reg = <10430 4dc>; + clock-frequency = <3f940aa>; + interrupt-map-mask = <f800 0 0 7>; + interrupt-map = < + + /* IDSEL 0x16 */ + b000 0 0 1 f8200000 40 0 + b000 0 0 2 f8200000 41 0 + b000 0 0 3 f8200000 42 0 + b000 0 0 4 f8200000 43 0 + + /* IDSEL 0x17 */ + b800 0 0 1 f8200000 43 0 + b800 0 0 2 f8200000 40 0 + b800 0 0 3 f8200000 41 0 + b800 0 0 4 f8200000 42 0 + + /* IDSEL 0x18 */ + c000 0 0 1 f8200000 42 0 + c000 0 0 2 f8200000 43 0 + c000 0 0 3 f8200000 40 0 + c000 0 0 4 f8200000 41 0>; + interrupt-parent = <10c00>; + interrupts = <14 3>; + bus-range = <0 0>; + ranges = <02000000 0 80000000 80000000 040000000
+ 01000000 0 00000000f60000000
02000000>;arch/powerpc/boot/dts/mpc8272ads.dts new file +19
-0+ }; + +/* May need to remove if on a part without crypto engine */ + crypto@30000 { + device_type = "crypto"; + model = "SEC2"; + compatible = "talitos"; + reg = <30000 10000>; + interrupts = <b 0>; + interrupt-parent = <10c00>; + num-channels = <4>; + channel-fifo-len = <18>; + exec-units-mask = <0000007e>; +/* desc mask is for rev1.x, we need runtime fixup for >=2.x */ + descriptor-types-mask = <01010ebf>; + }; + + }; +};
Re: [PATCH 1/3] POWERPC: Added devicetree for mpc8272ads board
Kumar,
Thanks a lot for extracting some time and glance at this approach... My comments below.
Quoted 34 lines · On Thu, 21 Sep 2006 23:55:36 -0500 Kumar Gala wrote:
Quoted 31 lines · Vitaly Bordug
This adds current dts file used with MPC8272ADS,
introducing new mdio bitbang defines, as well as
fully-CPM2-SoC board design.Signed-off-by Vitaly Bordug <[email protected]>---
arch/powerpc/boot/dts/mpc8272ads.dts | 236 +++++++++++++++++++++++ +++++++++++ 1 files changed, 236 insertions(+), 0 deletions(-)arch/powerpc/ renamed from arch/powerpc/boot/dts/mpc8272ads.dts +0
-0
boot/dts/mpc8272ads.dts
new file mode 100644
index 0000000..6d72b7darch/powerpc/boot/dts/mpc8272ads.dts new file +6
-0@@ -0,0 +1,236 @@ +/* + * MPC8272 ADS Device Tree Source + * + * Copyright 2005 Freescale Semiconductor Inc. + * + * This program is free software; you can redistribute it and/ormodify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
Quoted 9 lines
arch/powerpc/boot/dts/mpc8272ads.dts line 15
Quoted 6 lines
+ */
arch/powerpc/boot/dts/mpc8272ads.dts new file +5
-0+ + +/* +/memreserve/ 00000000 4000000; +*/Is this needed?
not necessarily-will clean up.
Quoted 19 lines
Quoted 19 lines
arch/powerpc/boot/dts/mpc8272ads.dts new file +19
-0+ +/ { + model = "MPC8272ADS"; + compatible = "MPC8260ADS"; + #address-cells = <1>; + #size-cells = <1>; + linux,phandle = <100>; + + cpus { + #cpus = <1>; + #address-cells = <1>; + #size-cells = <0>; + linux,phandle = <200>; + + PowerPC,8272@0 { + device_type = "cpu"; + reg = <0>; + d-cache-line-size = <20>; // 32 bytes + i-cache-line-size = <20>; // 32 bytes
Quoted 9 lines
arch/powerpc/boot/dts/mpc8272ads.dts line 39
Quoted 5 lines
arch/powerpc/boot/dts/mpc8272ads.dts new file +5
-0+ d-cache-size = <4000>; // L1, 16K + i-cache-size = <4000>; // L1, 16K + timebase-frequency = <17d7840>; + bus-frequency = <5f5e100>; + clock-frequency = <17D78400>;Are the freq's really fixed? if not having these values as 0, maybe be better.
On some path u-boot messed the frequencies, that's why here resides fixed approach. Eventually will be put back to <0> once it will definitely work.
Quoted 27 lines
Quoted 14 lines
arch/powerpc/boot/dts/mpc8272ads.dts new file +14
-0+ 32-bit; + linux,phandle = <201>; + linux,boot-cpu; + }; + }; + + interrupt-controller@f8200000 { + linux,phandle = <f8200000>; + #address-cells = <0>; + #interrupt-cells = <2>; + interrupt-controller; + reg = <f8200000 f8200004>; + built-in; + device_type = "pci-pic";arch/powerpc/boot/dts/mpc8272ads.dts line 63
Quoted 10 lines
arch/powerpc/boot/dts/mpc8272ads.dts new file +10
-0+ }; + memory { + device_type = "memory"; + linux,phandle = <300>; + reg = <00000000 4000000 f4500000 00000020>; + }; + + chosen { + name = "chosen"; + bootargs = "root=/dev/nfs rw ip=on";Seems bad form to put bootargs in the .dts directly like this.
Quoted 4 lines
Quoted 1 line
+ linux,stdout-path = "
/dev/ttyCPM0";I thought this was the 'of' path, not a dev path.
I was about to remove the upper stuff, and at the last moment missed that. Will clean up.
Quoted 113 lines
Quoted 113 lines
arch/powerpc/boot/dts/mpc8272ads.dts new file +113
-0+ linux,platform = <0>; + interrupt-controller = <10c00>; + linux,phandle = <400>; + }; + + soc8272@f0000000 { + #address-cells = <1>; + #size-cells = <1>; + #interrupt-cells = <2>; + device_type = "soc"; + ranges = < 0 0 2 00000000 f0000000 00053000>; + reg = <f0000000 0>; + + mdio@0 { + device_type = "mdio"; + compatible = "fs_enet"; + reg = <0 0>; + linux,phandle = <24520>; + #address-cells = <1>; + #size-cells = <0>; + ethernet-phy@0 { + linux,phandle = <2452000>; + interrupt-parent = <10c00>; + interrupts = <19 1>; + reg = <0>; + bitbang = [ 12 12 13 02 02 01 ]; + device_type = "ethernet-phy"; + }; + ethernet-phy@1 { + linux,phandle = <2452001>; + interrupt-parent = <10c00>; + interrupts = <19 1>; + bitbang = [ 12 12 13 02 02 01 ]; + reg = <3>; + device_type = "ethernet-phy"; + }; + }; + + ethernet@24000 { + #address-cells = <1>; + #size-cells = <0>; + device_type = "network"; + device-id = <2>; + compatible = "fs_enet"; + model = "FCC"; + reg = <11300 20 8400 100 11380 30>; + mac-address = [ 00 11 2F 99 43 54 ]; + interrupts = <20 2>; + interrupt-parent = <10c00>; + phy-handle = <2452000>; + rx-clock = <13>; + tx-clock = <12>; + }; + + ethernet@25000 { + device_type = "network"; + device-id = <3>; + compatible = "fs_enet"; + model = "FCC"; + reg = <11320 20 8500 100 113b0 30>; + mac-address = [ 00 11 2F 99 44 54 ]; + interrupts = <21 2>; + interrupt-parent = <10c00>; + phy-handle = <2452001>; + rx-clock = <17>; + tx-clock = <18>; + }; + + cpm@f0000000 { + linux,phandle = <f0000000>; + #address-cells = <1>; + #size-cells = <1>; + #interrupt-cells = <2>; + device_type = "cpm"; + model = "CPM2"; + ranges = <00000000 00000000 3ffff>; + reg = <10d80 3280>; + command-proc = <119c0>; + brg-frequency = <17D7840>; + cpm_clk = <BEBC200>; + + scc@11a00 { + device_type = "serial"; + compatible = "cpm_uart"; + model = "SCC"; + device-id = <2>; + reg = <11a00 20 8000 100>; + current-speed = <1c200>; + interrupts = <28 2>; + interrupt-parent = <10c00>; + clock-setup = <0 00ffffff>; + rx-clock = <1>; + tx-clock = <1>; + }; + + scc@11a60 { + device_type = "serial"; + compatible = "cpm_uart"; + model = "SCC"; + device-id = <5>; + reg = <11a60 20 8300 100>; + current-speed = <1c200>; + interrupts = <2b 2>; + interrupt-parent = <10c00>; + clock-setup = <1b ffffff00>; + rx-clock = <4>; + tx-clock = <4>; + }; + + }; + interrupt-controller@10c00 { + linux,phandle = <10c00>; + #address-cells = <0>;
Quoted 9 lines
arch/powerpc/boot/dts/mpc8272ads.dts line 183
Quoted 6 lines
arch/powerpc/boot/dts/mpc8272ads.dts new file +6
-0+ #interrupt-cells = <2>; + interrupt-controller; + reg = <10c00 80>; + built-in; + device_type = "cpm-pic"; + };Do we need to distinguish cpm2-pic from cpm-pic (8xx)?
IIRC, no, but I'll double-check.
Quoted 47 lines
Quoted 47 lines
arch/powerpc/boot/dts/mpc8272ads.dts new file +33
-0+ pci@0500 { + linux,phandle = <0500>; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + compatible = "8272"; + device_type = "pci"; + reg = <10430 4dc>; + clock-frequency = <3f940aa>; + interrupt-map-mask = <f800 0 0 7>; + interrupt-map = < + + /* IDSEL 0x16 */ + b000 0 0 1 f8200000 40 0 + b000 0 0 2 f8200000 41 0 + b000 0 0 3 f8200000 42 0 + b000 0 0 4 f8200000 43 0 + + /* IDSEL 0x17 */ + b800 0 0 1 f8200000 43 0 + b800 0 0 2 f8200000 40 0 + b800 0 0 3 f8200000 41 0 + b800 0 0 4 f8200000 42 0 + + /* IDSEL 0x18 */ + c000 0 0 1 f8200000 42 0 + c000 0 0 2 f8200000 43 0 + c000 0 0 3 f8200000 40 0 + c000 0 0 4 f8200000 41 0>; + interrupt-parent = <10c00>; + interrupts = <14 3>; + bus-range = <0 0>; + ranges = <02000000 0 80000000 80000000 040000000
+ 01000000 0 00000000f60000000
02000000>;arch/powerpc/boot/dts/mpc8272ads.dts new file +11
-0+ }; + +/* May need to remove if on a part without crypto engine */ + crypto@30000 { + device_type = "crypto"; + model = "SEC2"; + compatible = "talitos"; + reg = <30000 10000>; + interrupts = <b 0>; + interrupt-parent = <10c00>; + num-channels = <4>;
Quoted 10 lines
arch/powerpc/boot/dts/mpc8272ads.dts line 236
Quoted 8 lines
arch/powerpc/boot/dts/mpc8272ads.dts new file +8
-0+ channel-fifo-len = <18>; + exec-units-mask = <0000007e>; +/* desc mask is for rev1.x, we need runtime fixup for >=2.x */ + descriptor-types-mask = <01010ebf>; + }; + + }; +};
Sincerely, Vitaly
PATCH 2/3 POWERPC: 8272ads merge to powerpc: common stuff
In reply to Vitaly BordugThis has modules of common directories related to the mpc8272ADS board, mainly common cpm2 changes and fsl_soc.c portions related to the bitbang MDIO and other mechanisms specific for this family.
---
arch/powerpc/Kconfig | 1 + arch/powerpc/sysdev/cpm2_pic.c | 2 + arch/powerpc/sysdev/cpm2_pic.h | 2 + arch/powerpc/sysdev/fsl_soc.c | 68 ++++++++++++++++++++++++++++++++++++---- 4 files changed, 64 insertions(+), 9 deletions(-)
arch/powerpc/Kconfig +1 -0
@@ -594,6 +594,7 @@ endmenu source arch/powerpc/platforms/embedded6xx/Kconfig source arch/powerpc/platforms/4xx/Kconfig +source arch/powerpc/platforms/82xx/Kconfig source arch/powerpc/platforms/83xx/Kconfig source arch/powerpc/platforms/85xx/Kconfig source arch/powerpc/platforms/86xx/Kconfig
arch/powerpc/sysdev/cpm2_pic.c +1 -1
@@ -147,7 +147,7 @@ static struct irq_chip cpm2_pic = { .end = cpm2_end_irq, }; -int cpm2_get_irq (struct pt_regs *regs) +unsigned int cpm2_get_irq (struct pt_regs *regs) {int irq;unsigned long bits;
arch/powerpc/sysdev/cpm2_pic.h +1 -1
@@ -3,7 +3,7 @@ #define _PPC_KERNEL_CPM2_Hextern intctl_cpm2_t *cpm2_intctl; -extern int cpm2_get_irq (struct pt_regs *regs); +extern unsigned int cpm2_get_irq (struct pt_regs *regs);extern void cpm2_pic_init (struct device_node *);
arch/powerpc/sysdev/fsl_soc.c +61 -7
106 lines not on this page · raw message
PATCH 3/3 POWERPC: mpc8272ads merge: board-specific/platform stuff
In reply to Vitaly BordugThis intruduces 82xx family in arch/powerpc/platforms,
and has all the board-specific code to represent regression-less transaction from ppc. The functionality is apparently the same, including PCI controller.
---
arch/powerpc/Kconfig | 1 arch/powerpc/boot/dts/mpc8272ads.dts | 236 ---------------------------------- arch/powerpc/sysdev/cpm2_pic.c | 2 arch/powerpc/sysdev/cpm2_pic.h | 2 arch/powerpc/sysdev/fsl_soc.c | 68 +--------- 5 files changed, 9 insertions(+), 300 deletions(-)
arch/powerpc/Kconfig +0 -1
@@ -594,7 +594,6 @@ endmenu source arch/powerpc/platforms/embedded6xx/Kconfig source arch/powerpc/platforms/4xx/Kconfig -source arch/powerpc/platforms/82xx/Kconfig source arch/powerpc/platforms/83xx/Kconfig source arch/powerpc/platforms/85xx/Kconfig source arch/powerpc/platforms/86xx/Kconfig
arch/powerpc/boot/dts/mpc8272ads.dts deleted +0 -236
236 lines not on this page · raw message
arch/powerpc/sysdev/cpm2_pic.c +1 -1
@@ -147,7 +147,7 @@ static struct irq_chip cpm2_pic = { .end = cpm2_end_irq, }; -unsigned int cpm2_get_irq (struct pt_regs *regs) +int cpm2_get_irq (struct pt_regs *regs) {int irq;unsigned long bits;
arch/powerpc/sysdev/cpm2_pic.h +1 -1
@@ -3,7 +3,7 @@ #define _PPC_KERNEL_CPM2_Hextern intctl_cpm2_t *cpm2_intctl; -extern unsigned int cpm2_get_irq (struct pt_regs *regs); +extern int cpm2_get_irq (struct pt_regs *regs);extern void cpm2_pic_init (struct device_node *);
arch/powerpc/sysdev/fsl_soc.c +7 -61
106 lines not on this page · raw message
Re: [PATCH 3/3] POWERPC: mpc8272ads merge: board-specific/platform stuff
Paul,
Sorry, this patch is broken - something screwed up git commit it seems... I'll resend ASAP.
-Vitaly
Quoted 418 lines · On Fri, 22 Sep 2006 06:48:44 +0400 Vitaly Bordug <[email protected]> wrote:
This intruduces 82xx family in
arch/powerpc/platforms,
and has all the board-specific code to represent regression-less transaction from ppc. The functionality is apparently the same, including PCI controller.Signed-off-by Vitaly Bordug <[email protected]>---
arch/powerpc/Kconfig | 1 arch/powerpc/boot/dts/mpc8272ads.dts | 236 ---------------------------------- arch/powerpc/sysdev/cpm2_pic.c | 2 arch/powerpc/sysdev/cpm2_pic.h | 2 arch/powerpc/sysdev/fsl_soc.c | 68 +--------- 5 files changed, 9 insertions(+), 300 deletions(-)arch/powerpc/Kconfig +0
-1@@ -594,7 +594,6 @@ endmenu source arch/powerpc/platforms/embedded6xx/Kconfig source arch/powerpc/platforms/4xx/Kconfig -source arch/powerpc/platforms/82xx/Kconfig source arch/powerpc/platforms/83xx/Kconfig source arch/powerpc/platforms/85xx/Kconfig source arch/powerpc/platforms/86xx/Kconfigarch/powerpc/boot/dts/mpc8272ads.dts deleted +0
-236@@ -1,236 +0,0 @@ -/* - * MPC8272 ADS Device Tree Source - * - * Copyright 2005 Freescale Semiconductor Inc. - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - */ - - -/* -/memreserve/ 00000000 4000000; -*/ - -/ { - model = "MPC8272ADS"; - compatible = "MPC8260ADS"; - #address-cells = <1>; - #size-cells = <1>; - linux,phandle = <100>; - - cpus { - #cpus = <1>; - #address-cells = <1>; - #size-cells = <0>; - linux,phandle = <200>; - - PowerPC,8272@0 { - device_type = "cpu"; - reg = <0>; - d-cache-line-size = <20>; // 32 bytes - i-cache-line-size = <20>; // 32 bytes - d-cache-size = <4000>; // L1, 16K - i-cache-size = <4000>; // L1, 16K - timebase-frequency = <17d7840>; - bus-frequency = <5f5e100>; - clock-frequency = <17D78400>; - 32-bit; - linux,phandle = <201>; - linux,boot-cpu; - }; - }; - - interrupt-controller@f8200000 { - linux,phandle = <f8200000>; - #address-cells = <0>; - #interrupt-cells = <2>; - interrupt-controller; - reg = <f8200000 f8200004>; - built-in; - device_type = "pci-pic"; - }; - memory { - device_type = "memory"; - linux,phandle = <300>; - reg = <00000000 4000000 f4500000 00000020>; - }; - - chosen { - name = "chosen"; - bootargs = "root=/dev/nfs rw ip=on"; - linux,stdout-path = "/dev/ttyCPM0"; - linux,platform = <0>; - interrupt-controller = <10c00>; - linux,phandle = <400>; - }; - - soc8272@f0000000 { - #address-cells = <1>; - #size-cells = <1>; - #interrupt-cells = <2>; - device_type = "soc"; - ranges = < 0 0 2 00000000 f0000000 00053000>; - reg = <f0000000 0>; - - mdio@0 { - device_type = "mdio"; - compatible = "fs_enet"; - reg = <0 0>; - linux,phandle = <24520>; - #address-cells = <1>; - #size-cells = <0>; - ethernet-phy@0 { - linux,phandle = <2452000>; - interrupt-parent = <10c00>; - interrupts = <19 1>; - reg = <0>; - bitbang = [ 12 12 13 02 02 01 ]; - device_type = "ethernet-phy"; - }; - ethernet-phy@1 { - linux,phandle = <2452001>; - interrupt-parent = <10c00>; - interrupts = <19 1>; - bitbang = [ 12 12 13 02 02 01 ]; - reg = <3>; - device_type = "ethernet-phy"; - }; - }; - - ethernet@24000 { - #address-cells = <1>; - #size-cells = <0>; - device_type = "network"; - device-id = <2>; - compatible = "fs_enet"; - model = "FCC"; - reg = <11300 20 8400 100 11380 30>; - mac-address = [ 00 11 2F 99 43 54 ]; - interrupts = <20 2>; - interrupt-parent = <10c00>; - phy-handle = <2452000>; - rx-clock = <13>; - tx-clock = <12>; - }; - - ethernet@25000 { - device_type = "network"; - device-id = <3>; - compatible = "fs_enet"; - model = "FCC"; - reg = <11320 20 8500 100 113b0 30>; - mac-address = [ 00 11 2F 99 44 54 ]; - interrupts = <21 2>; - interrupt-parent = <10c00>; - phy-handle = <2452001>; - rx-clock = <17>; - tx-clock = <18>; - }; - - cpm@f0000000 { - linux,phandle = <f0000000>; - #address-cells = <1>; - #size-cells = <1>; - #interrupt-cells = <2>; - device_type = "cpm"; - model = "CPM2"; - ranges = <00000000 00000000 3ffff>; - reg = <10d80 3280>; - command-proc = <119c0>; - brg-frequency = <17D7840>; - cpm_clk = <BEBC200>; - - scc@11a00 { - device_type = "serial"; - compatible = "cpm_uart"; - model = "SCC"; - device-id = <2>; - reg = <11a00 20 8000 100>; - current-speed = <1c200>; - interrupts = <28 2>; - interrupt-parent = <10c00>; - clock-setup = <0 00ffffff>; - rx-clock = <1>; - tx-clock = <1>; - }; - - scc@11a60 { - device_type = "serial"; - compatible = "cpm_uart"; - model = "SCC"; - device-id = <5>; - reg = <11a60 20 8300 100>; - current-speed = <1c200>; - interrupts = <2b 2>; - interrupt-parent = <10c00>; - clock-setup = <1b ffffff00>; - rx-clock = <4>; - tx-clock = <4>; - }; - - }; - interrupt-controller@10c00 { - linux,phandle = <10c00>; - #address-cells = <0>; - #interrupt-cells = <2>; - interrupt-controller; - reg = <10c00 80>; - built-in; - device_type = "cpm-pic"; - }; - pci@0500 { - linux,phandle = <0500>; - #interrupt-cells = <1>; - #size-cells = <2>; - #address-cells = <3>; - compatible = "8272"; - device_type = "pci"; - reg = <10430 4dc>; - clock-frequency = <3f940aa>; - interrupt-map-mask = <f800 0 0 7>; - interrupt-map = < - - /* IDSEL 0x16 */ - b000 0 0 1 f8200000 40 0 - b000 0 0 2 f8200000 41 0 - b000 0 0 3 f8200000 42 0 - b000 0 0 4 f8200000 43 0 - - /* IDSEL 0x17 */ - b800 0 0 1 f8200000 43 0 - b800 0 0 2 f8200000 40 0 - b800 0 0 3 f8200000 41 0 - b800 0 0 4 f8200000 42 0 - - /* IDSEL 0x18 */ - c000 0 0 1 f8200000 42 0 - c000 0 0 2 f8200000 43 0 - c000 0 0 3 f8200000 40 0 - c000 0 0 4 f8200000 41 0>; - interrupt-parent = <10c00>; - interrupts = <14 3>; - bus-range = <0 0>; - ranges = <02000000 0 80000000 80000000 0 40000000 - 01000000 0 00000000 f6000000 0 02000000>; - }; - -/* May need to remove if on a part without crypto engine */ - crypto@30000 { - device_type = "crypto"; - model = "SEC2"; - compatible = "talitos"; - reg = <30000 10000>; - interrupts = <b 0>; - interrupt-parent = <10c00>; - num-channels = <4>; - channel-fifo-len = <18>; - exec-units-mask = <0000007e>; -/* desc mask is for rev1.x, we need runtime fixup for >=2.x */ - descriptor-types-mask = <01010ebf>; - }; - - }; -};arch/powerpc/sysdev/cpm2_pic.c +1
-1@@ -147,7 +147,7 @@ static struct irq_chip cpm2_pic = { .end = cpm2_end_irq, }; -unsigned int cpm2_get_irq (struct pt_regs *regs) +int cpm2_get_irq (struct pt_regs *regs) {int irq;unsigned long bits;arch/powerpc/sysdev/cpm2_pic.h +1
-1@@ -3,7 +3,7 @@ #define _PPC_KERNEL_CPM2_Hextern intctl_cpm2_t *cpm2_intctl; -extern unsigned int cpm2_get_irq (struct pt_regs *regs); +extern int cpm2_get_irq (struct pt_regs *regs);extern void cpm2_pic_init (struct device_node *);arch/powerpc/sysdev/fsl_soc.c +7
-61@@ -37,7 +37,6 @@ #include <mm/mmu_decl.h>#include <asm/cpm2.h> extern void init_fcc_ioports (struct fs_platform_info *); -extern void init_scc_ioports (struct fs_uart_platform_info *);static phys_addr_t immrbase =-1 ;phys_addr_t get_immrbase (void )@@ -567,7 +566,7 @@ static int __init fs_enet_of_init(void)struct resource r[4 ];struct device_node *phy, *mdio;struct fs_platform_info fs_enet_data; -const unsigned int *id, *phy_addr, phy_irq; +const unsigned int *id, *phy_addr;const void *mac_addr;const phandle *ph;const char *model;@@ -589,7 +588,6 @@ static int __init fs_enet_of_init(void)if (ret) goto err; r[2 ].name = fcc_regs_c; - fs_enet_data.fcc_regs_c = r[2 ].start; r[3 ].start = r[3 ].end =irq_of_parse_and_map (np,0 ); r[3 ].flags =IORESOURCE_IRQ ;@@ -622,8 +620,6 @@ static int __init fs_enet_of_init(void) phy_addr =get_property (phy,"reg" ,NULL ); fs_enet_data.phy_addr = *phy_addr; - phy_irq =get_property (phy,"interrupts" ,NULL ); - id =get_property (np,"device-id" ,NULL ); fs_enet_data.fs_no = *id;strcpy (fs_enet_data.fs_type, model);@@ -641,7 +637,6 @@ static int __init fs_enet_of_init(void)if (strstr (model,"FCC" )) {int fcc_index = *id -1 ; -unsigned char * mdio_bb_prop; fs_enet_data.dpram_offset = (u32 )cpm_dpram_addr (0 ); fs_enet_data.rx_ring =32 ;@@ -657,63 +652,14 @@ static int __init fs_enet_of_init(void) (u32)res.start, fs_enet_data.phy_addr); fs_enet_data.bus_id = (char *)&bus_id[(*id)]; fs_enet_data.init_ioports = init_fcc_ioports; + } - mdio_bb_prop =get_property (phy,"bitbang" ,NULL ); -if (mdio_bb_prop) { -struct platform_device *fs_enet_mdio_bb_dev; -struct fs_mii_bb_platform_info fs_enet_mdio_bb_data; - - fs_enet_mdio_bb_dev = -platform_device_register_simple ("fsl-bb-mdio" , - i,NULL ,0 ); -memset (&fs_enet_mdio_bb_data,0 , -sizeof (struct fs_mii_bb_platform_info )); - fs_enet_mdio_bb_data.mdio_dat.bit = - mdio_bb_prop[0 ]; - fs_enet_mdio_bb_data.mdio_dir.bit = - mdio_bb_prop[1 ]; - fs_enet_mdio_bb_data.mdc_dat.bit = - mdio_bb_prop[2 ]; - fs_enet_mdio_bb_data.mdio_port = - mdio_bb_prop[3 ]; - fs_enet_mdio_bb_data.mdc_port = - mdio_bb_prop[4 ]; - fs_enet_mdio_bb_data.delay = - mdio_bb_prop[5 ]; - - fs_enet_mdio_bb_data.irq[0 ] = phy_irq[0 ]; - fs_enet_mdio_bb_data.irq[1 ] =-1 ; - fs_enet_mdio_bb_data.irq[2 ] =-1 ; - fs_enet_mdio_bb_data.irq[3 ] = phy_irq[0 ]; - fs_enet_mdio_bb_data.irq[31 ] =-1 ; - - fs_enet_mdio_bb_data.mdio_dat.offset = - (u32)&cpm2_immr->im_ioport.iop_pdatc; - fs_enet_mdio_bb_data.mdio_dir.offset = - (u32)&cpm2_immr->im_ioport.iop_pdirc; - fs_enet_mdio_bb_data.mdc_dat.offset = - (u32)&cpm2_immr->im_ioport.iop_pdatc; - - ret =platform_device_add_data ( - fs_enet_mdio_bb_dev, - &fs_enet_mdio_bb_data, -sizeof (struct fs_mii_bb_platform_info )); -if (ret) - goto unreg; - }else { -printk (KERN_ERR -"mii-properties isn't found in device tree\n" ); - ret = -ENODEV ; - goto unreg; - } - } - -of_node_put (phy); -of_node_put (mdio); +of_node_put (phy); +of_node_put (mdio); - ret =platform_device_add_data (fs_enet_dev, &fs_enet_data, -sizeof (struct -fs_platform_info )); + ret =platform_device_add_data (fs_enet_dev, &fs_enet_data, +sizeof (struct +fs_platform_info ));if (ret) goto unreg; }_______________________________________________
Linuxppc-dev mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-dev
Signature · 2 lines
Sincerely, Vitaly