speedstep-ich issue
Upgrading kernel form version 2.6.17.2 to 2.6.18 the cpufreq system makes
strange things.. looking at dmesg (with debugging enabled for cpufreq) it seems that after a while the system recognizes only one step of frequency (the slowest) .. The CPU is a P3 that can change the frequency from 730 MHz to 1.1 GHz, using the speedstep-ich driver. Tell me if you need more informations..
Quoted 6 lines · Marco cusmai
Upgrading kernel form version 2.6.17.2 to 2.6.18 the cpufreq system makes
strange things.. looking at dmesg (with debugging enabled for cpufreq) it seems that after a while the system recognizes only one step of frequency (the slowest) .. The CPU is a P3 that can change the frequency from 730 MHz to 1.1 GHz, using the speedstep-ich driver. Tell me if you need more informations..
probably dmesg output and some kind of evidence of the problem you're reporting would be appreciated.
Regards
Signature · 2 lines
mattia :wq!
Quoted 8 lines · Mattia Dongili
Quoted 6 lines · Marco cusmai
Upgrading kernel form version 2.6.17.2 to 2.6.18 the cpufreq system makes
strange things.. looking at dmesg (with debugging enabled for cpufreq)
it seems that after a while the system recognizes only one step of frequency (the slowest) .. The CPU is a P3 that can change the frequency from 730 MHz to 1.1 GHz, using the speedstep-ich driver. Tell me if you need more informations..
Quoted 4 lines
probably dmesg output and some kind of evidence of the problem you're reporting would be appreciated.
Regards
Here it is some dmesg output with cpufreq.debug=2
speedstep-lib: x86: 6, model: b
speedstep-lib: ebx is 6
speedstep-ich: pmbase is 0x1000
speedstep-lib: trying to determine both speeds
speedstep-lib: P3 - MSR_IA32_EBL_CR_POWERON: 0xcd840020 0x0
speedstep-lib: speed is 1130500
speedstep-lib: previous speed is 1130500
speedstep-ich: read at pmbase 0x1000 + 0x50 returned 0x0
speedstep-ich: writing 0x1 to pmbase 0x1000 + 0x50
speedstep-ich: read at pmbase 0x1000 + 0x50 returned 0x1
speedstep-lib: P3 - MSR_IA32_EBL_CR_POWERON: 0xc5040020 0x0
speedstep-lib: speed is 731500
speedstep-ich: change to 731 MHz succeeded
speedstep-lib: P3 - MSR_IA32_EBL_CR_POWERON: 0xc5040020 0x0
speedstep-lib: speed is 731500
speedstep-lib: low speed is 731500
speedstep-ich: read at pmbase 0x1000 + 0x50 returned 0x1
speedstep-ich: writing 0x0 to pmbase 0x1000 + 0x50
speedstep-ich: read at pmbase 0x1000 + 0x50 returned 0x0
speedstep-lib: P3 - MSR_IA32_EBL_CR_POWERON: 0xcd840020 0x0
speedstep-lib: speed is 1130500
speedstep-ich: change to 1130 MHz succeeded
speedstep-lib: P3 - MSR_IA32_EBL_CR_POWERON: 0xcd840020 0x0
speedstep-lib: speed is 1130500
speedstep-lib: high speed is 1130500
speedstep-lib: transition latency is 0 uSec
speedstep: frequency transition measured seems out of range (0 nSec), falling back to a safe one of 500000 nSec.
speedstep-lib: P3 - MSR_IA32_EBL_CR_POWERON: 0xcd840020 0x0
speedstep-lib: speed is 1130500
speedstep-ich: detected 1130500 kHz as current frequency
speedstep-ich: currently at high speed setting - 1130 MHz
speedstep-lib: P3 - MSR_IA32_EBL_CR_POWERON: 0xcd840020 0x0
speedstep-lib: speed is 1130500
speedstep-ich: detected 1130500 kHz as current frequency
speedstep-ich: transiting from 1130500 to 1130500 kHz
Here starts the userspace program (cpufreqd):
speedstep-lib: P3 - MSR_IA32_EBL_CR_POWERON: 0xcd840020 0x0
speedstep-lib: speed is 1130500
speedstep-ich: detected 1130500 kHz as current frequency
speedstep-ich: transiting from 1130500 to 1130500 kHz
speedstep-lib: P3 - MSR_IA32_EBL_CR_POWERON: 0xcd840020 0x0
speedstep-lib: speed is 1130500
speedstep-ich: detected 1130500 kHz as current frequency
speedstep-ich: transiting from 1130500 to 731500 kHz
speedstep-ich: read at pmbase 0x1000 + 0x50 returned 0x0
speedstep-ich: writing 0x1 to pmbase 0x1000 + 0x50
speedstep-ich: read at pmbase 0x1000 + 0x50 returned 0x1
speedstep-lib: P3 - MSR_IA32_EBL_CR_POWERON: 0xc5040020 0x0
speedstep-lib: speed is 731500
speedstep-ich: change to 731 MHz succeeded
speedstep-lib: P3 - MSR_IA32_EBL_CR_POWERON: 0xc5040020 0x0
speedstep-lib: speed is 731500
speedstep-ich: detected 731500 kHz as current frequency
speedstep-ich: transiting from 731500 to 731500 kHz
speedstep-lib: P3 - MSR_IA32_EBL_CR_POWERON: 0xc5040020 0x0
speedstep-lib: speed is 731500
speedstep-ich: detected 731500 kHz as current frequency
speedstep-ich: transiting from 731500 to 731500 kHz
from now on the frequency stays on 731500 kHz..
I've tried to read informations from the sys interface:
cat scaling_available_frequencies : 1130500 731500 cat scaling_min_freq : 731500
cat scaling_max_freq : 731500
trying to change frequency through scaling_setspeed does nothing.
I've also noticed these errors during ACPI startup
acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5decode_hpp: Could not get hotplug parameters. Use defaults
acpiphp: Slot [1] registeredacpiphp_ibm: ibm_find_acpi_device: Failed to get device information<3>acpiphp_ibm: ibm_find_acpi_device: Failed to get device information<3>acpiphp_ibm: ibm_acpiphp_init: acpi_walk_namespace failed
Hi,
Quoted 3 lines · Marco cusmai
cat
scaling_available_frequencies: 1130500 731500 catscaling_min_freq: 731500
catscaling_max_freq: 731500
Yes, then it won't scale any more -- the CPU will only be set to a value between scaling_min_freq and scaling_max_freq. Therefore, please check the configuration file for cpufreqd (or any other cpufreq daemon you're running).
Thanks,
Dominik
Quoted 8 lines · Dominik Brodowski
Hi,
Quoted 3 lines · Marco cusmai
cat
scaling_available_frequencies: 1130500 731500 catscaling_min_freq: 731500
catscaling_max_freq: 731500
Quoted 8 lines
Yes, then it won't scale any more -- the CPU will only be set to a value between
scaling_min_freqandscaling_max_freq. Therefore, please check the configuration file for cpufreqd (or any other cpufreq daemon you're running).Thanks,
Dominik
For my tests I've already disabled the cpufreqd deamon at startup.. The results are the same.
I've also tried the following:
echo 1130500 > scaling_setspeed
cat scaling_cur_freq : 731500
The governor I actualy use is "userspace". Even with "performance" the freq stays low
Quoted 18 lines · Marco Cusmai
Quoted 8 lines · Dominik Brodowski
Hi,
Quoted 3 lines · Marco cusmai
cat
scaling_available_frequencies: 1130500 731500 catscaling_min_freq: 731500
catscaling_max_freq: 731500Quoted 9 lines
Yes, then it won't scale any more -- the CPU will only be set to a value between
scaling_min_freqandscaling_max_freq. Therefore, please check the
configuration file for cpufreqd (or any other cpufreq daemon you're running).Thanks,
Dominik
Quoted 6 lines
For my tests I've already disabled the cpufreqd deamon at startup.. The results are the same.
I've also tried the following:echo 1130500 >
scaling_setspeed
catscaling_cur_freq: 731500
try this before:
$ echo 1130500 > scaling_max_freq
As explained, scaling_max_freq and scaling_min_freq define the upper and lower limit to which the processor is bound (this is a software enforced limit), so if this limit is MAX=MIN=731500 then the kernel won't allow 1130500.
Signature · 2 lines
mattia :wq!