skge: fiber related fixes
Subsystems (2)
cover skge: fiber related fixes
These patches address the problems that were causing a fiber connected SysKonnect board to revert to have performance problems. They fix flow control, duplex, and irq masking issues.
--
Stephen Hemminger <[email protected]>
PATCH 1/4 skge: fix stuck irq when fiber down
The PHY interrupt from the internal fiber is getting stuck on when the link is down. Add code to handle the transition and mask it.
--- drivers/net/skge.c | 53 +++++++++++++++++++++++++++++++++++------------------ drivers/net/skge.h | 3 ++- 2 files changed, 37 insertions(+), 19 deletions(-)
drivers/net/skge.c +35 -18
@@ -884,6 +884,29 @@ static void skge_link_down(struct skge_p printk(KERN_INFO PFX "%s: Link is down.\n", skge->netdev->name); } + +static void xm_link_down (struct skge_hw *hw,int port) +{ +struct net_device *dev = hw->dev[port]; +struct skge_port *skge =netdev_priv (dev); +u16 cmd, msk; + +if (hw->phy_type ==SK_PHY_XMAC ) { + msk =xm_read16 (hw, port,XM_IMSK ); + msk |=XM_IS_INP_ASS |XM_IS_LIPA_RC |XM_IS_RX_PAGE |XM_IS_AND ; +xm_write16 (hw, port,XM_IMSK , msk); + } + + cmd =xm_read16 (hw, port,XM_MMU_CMD ); + cmd &= ~(XM_MMU_ENA_RX |XM_MMU_ENA_TX ); +xm_write16 (hw, port,XM_MMU_CMD , cmd); +/* dummy read to ensure writing */ + (void )xm_read16 (hw, port,XM_MMU_CMD ); + +if (netif_carrier_ok (dev)) +skge_link_down (skge); +} +static int __xm_phy_read (struct skge_hw *hw,int port,u16 reg,u16 *val) {int i;
@@ -1008,14 +1031,7 @@ static void bcom_check_link(struct skge_ status =xm_phy_read (hw, port,PHY_BCOM_STAT );if ((status &PHY_ST_LSYNC ) ==0 ) { -u16 cmd =xm_read16 (hw, port,XM_MMU_CMD ); - cmd &= ~(XM_MMU_ENA_RX |XM_MMU_ENA_TX ); -xm_write16 (hw, port,XM_MMU_CMD , cmd); -/* dummy read to ensure writing */ - (void )xm_read16 (hw, port,XM_MMU_CMD ); - -if (netif_carrier_ok (dev)) -skge_link_down (skge); +xm_link_down (hw, port);return ; }
@@ -1235,14 +1251,7 @@ static void xm_check_link(struct net_dev status =xm_phy_read (hw, port,PHY_XMAC_STAT );if ((status &PHY_ST_LSYNC ) ==0 ) { -u16 cmd =xm_read16 (hw, port,XM_MMU_CMD ); - cmd &= ~(XM_MMU_ENA_RX |XM_MMU_ENA_TX ); -xm_write16 (hw, port,XM_MMU_CMD , cmd); -/* dummy read to ensure writing */ - (void )xm_read16 (hw, port,XM_MMU_CMD ); - -if (netif_carrier_ok (dev)) -skge_link_down (skge); +xm_link_down (hw, port);return ; }
@@ -1568,6 +1577,10 @@ static void genesis_mac_intr(struct skge printk(KERN_DEBUG PFX "%s: mac interrupt status 0x%x\n", skge->netdev->name, status); +if (hw->phy_type ==SK_PHY_XMAC && + (status & (XM_IS_INP_ASS |XM_IS_LIPA_RC ))) +xm_link_down (hw, port); +if (status &XM_IS_TXF_UR ) {xm_write32 (hw, port,XM_MODE ,XM_MD_FTF ); ++skge->net_stats.tx_fifo_errors;
@@ -1582,7 +1595,7 @@ static void genesis_link_up(struct skge_ {struct skge_hw *hw = skge->hw;int port = skge->port; -u16 cmd; +u16 cmd, msk;u32 mode; cmd =xm_read16 (hw, port,XM_MMU_CMD );
@@ -1631,7 +1644,11 @@ static void genesis_link_up(struct skge_ }xm_write32 (hw, port,XM_MODE , mode); -xm_write16 (hw, port,XM_IMSK ,XM_DEF_MSK ); + msk =XM_DEF_MSK ; +if (hw->phy_type !=SK_PHY_XMAC ) + msk |=XM_IS_INP_ASS ;/* disable GP0 interrupt bit */ + +xm_write16 (hw, port,XM_IMSK , msk);xm_read16 (hw, port,XM_ISRC );/* get MMU Command Reg. */
drivers/net/skge.h +2 -1
@@ -2195,7 +2195,8 @@ enum { XM_IS_RX_COMP = 1<<0, /* Bit 0: Frame Rx Complete */ }; -#define XM_DEF_MSK (~(XM_IS_RXC_OV | XM_IS_TXC_OV | XM_IS_RXF_OV | XM_IS_TXF_UR)) +#define XM_DEF_MSK (~(XM_IS_INP_ASS | XM_IS_LIPA_RC | \ + XM_IS_RXF_OV | XM_IS_TXF_UR))/* XM_HW_CFG 16 bit r/w Hardware Config Register */
--
Stephen Hemminger <[email protected]>
PATCH 2/4 skge: pause mapping for fiber
In reply to Stephen HemmingerDo correct mapping of pause and duplex when using 1000BaseX fiber versions of the board.
--- drivers/net/skge.c | 38 +++++++++++++++++++++----------------- 1 file changed, 21 insertions(+), 17 deletions(-)
drivers/net/skge.c +21 -17
@@ -197,8 +197,8 @@ static u32 skge_supported_modes(const stelse if (hw->chip_id ==CHIP_ID_YUKON ) supported &= ~SUPPORTED_1000baseT_Half; }else - supported = SUPPORTED_1000baseT_Full |SUPPORTED_FIBRE - | SUPPORTED_Autoneg; + supported = SUPPORTED_1000baseT_Full | SUPPORTED_1000baseT_Half + |SUPPORTED_FIBRE | SUPPORTED_Autoneg;return supported; }
@@ -1018,6 +1018,14 @@ static const u16 phy_pause_map[] = { [FLOW_MODE_REM_SEND] = PHY_AN_PAUSE_CAP | PHY_AN_PAUSE_ASYM, }; +/* special defines for FIBER (88E1011S only) */ +static const u16 fiber_pause_map[] = { + [FLOW_MODE_NONE ] =PHY_X_P_NO_PAUSE , + [FLOW_MODE_LOC_SEND ] =PHY_X_P_ASYM_MD , + [FLOW_MODE_SYMMETRIC ] =PHY_X_P_SYM_MD , + [FLOW_MODE_REM_SEND ] =PHY_X_P_BOTH_MD , +}; +/* Check status of Broadcom phy link */ static void bcom_check_link (struct skge_hw *hw,int port)
@@ -1207,17 +1215,7 @@ static void xm_phy_init(struct skge_portif (skge->advertising & ADVERTISED_1000baseT_Full) ctrl |=PHY_X_AN_FD ; -switch (skge->flow_control) { -case FLOW_MODE_NONE : - ctrl |=PHY_X_P_NO_PAUSE ; -break ; -case FLOW_MODE_LOC_SEND : - ctrl |=PHY_X_P_ASYM_MD ; -break ; -case FLOW_MODE_SYMMETRIC : - ctrl |=PHY_X_P_BOTH_MD ; -break ; - } + ctrl |= fiber_pause_map[skge->flow_control];xm_phy_write (hw, port,PHY_XMAC_AUNE_ADV , ctrl);
@@ -1796,11 +1794,17 @@ static void yukon_init(struct skge_hw *h adv |=PHY_M_AN_10_FD ;if (skge->advertising & ADVERTISED_10baseT_Half) adv |=PHY_M_AN_10_HD ; - }else /* special defines for FIBER (88E1011S only) */ - adv |=PHY_M_AN_1000X_AHD |PHY_M_AN_1000X_AFD ; -/* Set Flow-control capabilities */ - adv |= phy_pause_map[skge->flow_control]; +/* Set Flow-control capabilities */ + adv |= phy_pause_map[skge->flow_control]; + }else { +if (skge->advertising & ADVERTISED_1000baseT_Full) + adv |=PHY_M_AN_1000X_AFD ; +if (skge->advertising & ADVERTISED_1000baseT_Half) + adv |=PHY_M_AN_1000X_AHD ; + + adv |= fiber_pause_map[skge->flow_control]; + }/* Restart Auto-negotiation */ ctrl |=PHY_CT_ANE |PHY_CT_RE_CFG ;
--
Stephen Hemminger <[email protected]>
PATCH 3/4 skge: better flow control negotiation
In reply to Stephen HemmingerDo flow control negotiation properly. Don't let auto negotiation status limit renegotiation. Separate desired pause values from the result of auto negotiation.
--- drivers/net/skge.c | 129 ++++++++++++++++++++++++++++++++--------------------- drivers/net/skge.h | 22 ++++++--- 2 files changed, 95 insertions(+), 56 deletions(-)
drivers/net/skge.c +78 -51
@@ -487,31 +487,37 @@ static void skge_get_pauseparam(struct n {struct skge_port *skge =netdev_priv (dev); - ecmd->tx_pause = (skge->flow_control ==FLOW_MODE_LOC_SEND ) - || (skge->flow_control ==FLOW_MODE_SYMMETRIC ); - ecmd->rx_pause = (skge->flow_control ==FLOW_MODE_REM_SEND ) - || (skge->flow_control ==FLOW_MODE_SYMMETRIC ); + ecmd->rx_pause = (skge->flow_control ==FLOW_MODE_SYMMETRIC ) + || (skge->flow_control ==FLOW_MODE_SYM_OR_REM ); + ecmd->tx_pause = ecmd->rx_pause || (skge->flow_control ==FLOW_MODE_LOC_SEND ); - ecmd->autoneg = skge->autoneg; + ecmd->autoneg = ecmd->rx_pause || ecmd->tx_pause; }static int skge_set_pauseparam (struct net_device *dev,struct ethtool_pauseparam *ecmd) {struct skge_port *skge =netdev_priv (dev); +struct ethtool_pauseparam old; - skge->autoneg = ecmd->autoneg; -if (ecmd->rx_pause && ecmd->tx_pause) - skge->flow_control =FLOW_MODE_SYMMETRIC ; -else if (ecmd->rx_pause && !ecmd->tx_pause) - skge->flow_control =FLOW_MODE_REM_SEND ; -else if (!ecmd->rx_pause && ecmd->tx_pause) - skge->flow_control =FLOW_MODE_LOC_SEND ; -else - skge->flow_control =FLOW_MODE_NONE ; +skge_get_pauseparam (dev, &old); + +if (ecmd->autoneg != old.autoneg) + skge->flow_control = ecmd->autoneg ?FLOW_MODE_NONE :FLOW_MODE_SYMMETRIC ; +else { +if (ecmd->rx_pause && ecmd->tx_pause) + skge->flow_control =FLOW_MODE_SYMMETRIC ; +else if (ecmd->rx_pause && !ecmd->tx_pause) + skge->flow_control =FLOW_MODE_SYM_OR_REM ; +else if (!ecmd->rx_pause && ecmd->tx_pause) + skge->flow_control =FLOW_MODE_LOC_SEND ; +else + skge->flow_control =FLOW_MODE_NONE ; + }if (netif_running (dev))skge_phy_reset (skge); +return 0 ; }
@@ -854,6 +860,23 @@ static int skge_rx_fill(struct net_devicreturn 0 ; } +static const char *skge_pause (enum pause_status status) +{ +switch (status) { +case FLOW_STAT_NONE : +return "none" ; +case FLOW_STAT_REM_SEND : +return "rx only" ; +case FLOW_STAT_LOC_SEND : +return "tx_only" ; +case FLOW_STAT_SYMMETRIC :/* Both station may send PAUSE */ +return "both" ; +default : +return "indeterminated" ; + } +} + +static void skge_link_up (struct skge_port *skge) { skge_write8(skge->hw, SK_REG(skge->port, LNK_LED_REG),
@@ -862,16 +885,13 @@ static void skge_link_up(struct skge_pornetif_carrier_on (skge->netdev);netif_wake_queue (skge->netdev); -if (netif_msg_link (skge)) +if (netif_msg_link (skge)) { printk(KERN_INFO PFX"%s: Link is up at %d Mbps, %s duplex, flow control %s\n" , skge->netdev->name, skge->speed, skge->duplex ==DUPLEX_FULL ?"full" :"half" , - (skge->flow_control ==FLOW_MODE_NONE ) ?"none" : - (skge->flow_control ==FLOW_MODE_LOC_SEND ) ?"tx only" : - (skge->flow_control ==FLOW_MODE_REM_SEND ) ?"rx only" : - (skge->flow_control ==FLOW_MODE_SYMMETRIC ) ?"tx and rx" : -"unknown" ); + skge_pause(skge->flow_status)); + } }static void skge_link_down (struct skge_port *skge)
@@ -1015,7 +1035,7 @@ static const u16 phy_pause_map[] = { [FLOW_MODE_NONE] = 0, [FLOW_MODE_LOC_SEND] = PHY_AN_PAUSE_ASYM, [FLOW_MODE_SYMMETRIC] = PHY_AN_PAUSE_CAP, - [FLOW_MODE_REM_SEND] = PHY_AN_PAUSE_CAP | PHY_AN_PAUSE_ASYM, + [FLOW_MODE_SYM_OR_REM] = PHY_AN_PAUSE_CAP | PHY_AN_PAUSE_ASYM, };/* special defines for FIBER (88E1011S only) */
@@ -1023,7 +1043,7 @@ static const u16 fiber_pause_map[] = { [FLOW_MODE_NONE] = PHY_X_P_NO_PAUSE, [FLOW_MODE_LOC_SEND] = PHY_X_P_ASYM_MD, [FLOW_MODE_SYMMETRIC] = PHY_X_P_SYM_MD, - [FLOW_MODE_REM_SEND] = PHY_X_P_BOTH_MD, + [FLOW_MODE_SYM_OR_REM] = PHY_X_P_BOTH_MD, };
@@ -1072,20 +1092,19 @@ static void bcom_check_link(struct skge_return ; } -/* We are using IEEE 802.3z/D5.0 Table 37-4 */ switch (aux &PHY_B_AS_PAUSE_MSK ) {case PHY_B_AS_PAUSE_MSK : - skge->flow_control =FLOW_MODE_SYMMETRIC ; + skge->flow_status =FLOW_STAT_SYMMETRIC ;break ;case PHY_B_AS_PRR : - skge->flow_control =FLOW_MODE_REM_SEND ; + skge->flow_status =FLOW_STAT_REM_SEND ;break ;case PHY_B_AS_PRT : - skge->flow_control =FLOW_MODE_LOC_SEND ; + skge->flow_status =FLOW_STAT_LOC_SEND ;break ;default : - skge->flow_control =FLOW_MODE_NONE ; + skge->flow_status =FLOW_STAT_NONE ; } skge->speed =SPEED_1000 ; }
@@ -1283,15 +1302,20 @@ static void xm_check_link(struct net_dev }/* We are using IEEE 802.3z/D5.0 Table 37-4 */ -if (lpa &PHY_X_P_SYM_MD ) - skge->flow_control =FLOW_MODE_SYMMETRIC ; -else if ((lpa &PHY_X_RS_PAUSE ) ==PHY_X_P_ASYM_MD ) - skge->flow_control =FLOW_MODE_REM_SEND ; -else if ((lpa &PHY_X_RS_PAUSE ) ==PHY_X_P_BOTH_MD ) - skge->flow_control =FLOW_MODE_LOC_SEND ; +if ((skge->flow_control ==FLOW_MODE_SYMMETRIC || + skge->flow_control ==FLOW_MODE_SYM_OR_REM ) && + (lpa &PHY_X_P_SYM_MD )) + skge->flow_status =FLOW_STAT_SYMMETRIC ; +else if (skge->flow_control ==FLOW_MODE_SYM_OR_REM && + (lpa &PHY_X_RS_PAUSE ) ==PHY_X_P_ASYM_MD ) +/* Enable PAUSE receive, disable PAUSE transmit */ + skge->flow_status =FLOW_STAT_REM_SEND ; +else if (skge->flow_control ==FLOW_MODE_LOC_SEND && + (lpa &PHY_X_RS_PAUSE ) ==PHY_X_P_BOTH_MD ) +/* Disable PAUSE receive, enable PAUSE transmit */ + skge->flow_status =FLOW_STAT_LOC_SEND ;else - skge->flow_control =FLOW_MODE_NONE ; - + skge->flow_status =FLOW_STAT_NONE ; skge->speed =SPEED_1000 ; }
@@ -1602,8 +1626,8 @@ static void genesis_link_up(struct skge_* enabling pause frame reception is required for 1000BT * because the XMAC is not reset if the link is going down */ -if (skge->flow_control ==FLOW_MODE_NONE || - skge->flow_control ==FLOW_MODE_LOC_SEND ) +if (skge->flow_status ==FLOW_STAT_NONE || + skge->flow_status ==FLOW_STAT_LOC_SEND )/* Disable Pause Frame Reception */ cmd |=XM_MMU_IGN_PF ;else
@@ -1613,8 +1637,8 @@ static void genesis_link_up(struct skge_xm_write16 (hw, port,XM_MMU_CMD , cmd); mode =xm_read32 (hw, port,XM_MODE ); -if (skge->flow_control ==FLOW_MODE_SYMMETRIC || - skge->flow_control ==FLOW_MODE_LOC_SEND ) { +if (skge->flow_status==FLOW_STAT_SYMMETRIC || + skge->flow_status ==FLOW_STAT_LOC_SEND ) {/* * Configure Pause Frame Generation * Use internal and external Pause Frame Generation.
@@ -1938,6 +1962,11 @@ static void yukon_mac_init(struct skge_hcase FLOW_MODE_LOC_SEND :/* disable Rx flow-control */ reg |=GM_GPCR_FC_RX_DIS |GM_GPCR_AU_FCT_DIS ; +break ; +case FLOW_MODE_SYMMETRIC : +case FLOW_MODE_SYM_OR_REM : +/* enable Tx & Rx flow-control */ +break ; }gma_write16 (hw, port,GM_GP_CTRL , reg);
@@ -2132,13 +2161,11 @@ static void yukon_link_down(struct skge_ ctrl &= ~(GM_GPCR_RX_ENA |GM_GPCR_TX_ENA );gma_write16 (hw, port,GM_GP_CTRL , ctrl); -if (skge->flow_control ==FLOW_MODE_REM_SEND ) { +if (skge->flow_status ==FLOW_STAT_REM_SEND ) { + ctrl =gm_phy_read (hw, port,PHY_MARV_AUNE_ADV ); + ctrl |=PHY_M_AN_ASP ;/* restore Asymmetric Pause bit */ -gm_phy_write (hw, port,PHY_MARV_AUNE_ADV , -gm_phy_read (hw, port, -PHY_MARV_AUNE_ADV ) - |PHY_M_AN_ASP ); - +gm_phy_write (hw, port,PHY_MARV_AUNE_ADV , ctrl); }yukon_reset (hw, port);
@@ -2185,19 +2212,19 @@ static void yukon_phy_intr(struct skge_p/* We are using IEEE 802.3z/D5.0 Table 37-4 */ switch (phystat &PHY_M_PS_PAUSE_MSK ) {case PHY_M_PS_PAUSE_MSK : - skge->flow_control =FLOW_MODE_SYMMETRIC ; + skge->flow_status =FLOW_STAT_SYMMETRIC ;break ;case PHY_M_PS_RX_P_EN : - skge->flow_control =FLOW_MODE_REM_SEND ; + skge->flow_status =FLOW_STAT_REM_SEND ;break ;case PHY_M_PS_TX_P_EN : - skge->flow_control =FLOW_MODE_LOC_SEND ; + skge->flow_status =FLOW_STAT_LOC_SEND ;break ;default : - skge->flow_control =FLOW_MODE_NONE ; + skge->flow_status =FLOW_STAT_NONE ; } -if (skge->flow_control ==FLOW_MODE_NONE || +if (skge->flow_status ==FLOW_STAT_NONE || (skge->speed <SPEED_1000 && skge->duplex ==DUPLEX_HALF ))skge_write8 (hw,SK_REG (port,GMAC_CTRL ),GMC_PAUSE_OFF );else
@@ -3420,7 +3447,7 @@ static struct net_device *skge_devinit(s/* Auto speed and flow control */ skge->autoneg =AUTONEG_ENABLE ; - skge->flow_control =FLOW_MODE_SYMMETRIC ; + skge->flow_control =FLOW_MODE_SYM_OR_REM ; skge->duplex =-1 ; skge->speed =-1 ; skge->advertising =skge_supported_modes (hw);
drivers/net/skge.h +17 -5
@@ -2427,13 +2427,24 @@ struct skge_hw {struct mutex phy_mutex; }; -enum { -FLOW_MODE_NONE =0 ,/* No Flow-Control */ -FLOW_MODE_LOC_SEND =1 ,/* Local station sends PAUSE */ -FLOW_MODE_REM_SEND =2 ,/* Symmetric or just remote */ +enum pause_control { +FLOW_MODE_NONE =1 ,/* No Flow-Control */ +FLOW_MODE_LOC_SEND =2 ,/* Local station sends PAUSE */ FLOW_MODE_SYMMETRIC =3 ,/* Both stations may send PAUSE */ +FLOW_MODE_SYM_OR_REM =4 ,/* Both stations may send PAUSE or +* just the remote station may send PAUSE +*/ }; +enum pause_status { +FLOW_STAT_INDETERMINATED =0 ,/* indeterminated */ +FLOW_STAT_NONE ,/* No Flow Control */ +FLOW_STAT_REM_SEND ,/* Remote Station sends PAUSE */ +FLOW_STAT_LOC_SEND ,/* Local station sends PAUSE */ +FLOW_STAT_SYMMETRIC ,/* Both station may send PAUSE */ +}; + +struct skge_port {u32 msg_enable;struct skge_hw *hw;
@@ -2446,9 +2457,10 @@ struct skge_port {struct net_device_stats net_stats;struct work_struct link_thread; +enum pause_control flow_control; +enum pause_status flow_status;u8 rx_csum;u8 blink_on; -u8 flow_control;u8 wol;u8 autoneg;/* AUTONEG_ENABLE, AUTONEG_DISABLE */ u8 duplex;/* DUPLEX_HALF, DUPLEX_FULL */
--
Stephen Hemminger <[email protected]>
PATCH 4/4 skge: version 1.9
In reply to Stephen HemmingerWant to be able to track downstream impact of fiber related fixes.
drivers/net/skge.c +1 -1
@@ -43,7 +43,7 @@#include "skge.h" #define DRV_NAME "skge" -#define DRV_VERSION "1.8" +#define DRV_VERSION "1.9"#define PFX DRV_NAME " "#define DEFAULT_TX_RING_SIZE 128
--
Stephen Hemminger <[email protected]>
Re: [PATCH 4/4] skge: version 1.9
The skge 1.9 patch is looking good on older syskonnect fiber cards. Stability issues seem to be taken care of and performance is good. There are some strange interactions with bonding, however. If I try to put both interfaces of an sk-9844 into a bonded interface, I only see traffic from one of them. If I try to config the bonded interface down, the system hangs. If I tcpdump either of the individual interfaces (before bonding them) I see all the expected traffic.
Mike Stone
Re: [PATCH 4/4] skge: version 1.9
Quoted 9 lines · On Tue, 07 Nov 2006 08:25:07 -0500 Michael Stone <[email protected]> wrote:
The skge 1.9 patch is looking good on older syskonnect fiber cards. Stability issues seem to be taken care of and performance is good. There are some strange interactions with bonding, however. If I try to put both interfaces of an sk-9844 into a bonded interface, I only see traffic from one of them. If I try to config the bonded interface down, the system hangs. If I tcpdump either of the individual interfaces (before bonding them) I see all the expected traffic.
Mike Stone
Which form of bonding link checking are you using. It could be that bonding MII checking is confused.
Signature · 1 line
Stephen Hemminger <[email protected]>
Re: [PATCH 4/4] skge: version 1.9
Quoted 2 lines · Stephen Hemminger
Which form of bonding link checking are you using. It could be that bonding MII checking is confused.
I'm not specifying anything, just "ifenslave bond0 eth2 eth3"
Mike Stone
Re: [PATCH 4/4] skge: version 1.9
Quoted 7 lines · On Tue, 07 Nov 2006 13:58:31 -0500 Michael Stone <[email protected]> wrote:
Quoted 2 lines · Stephen Hemminger
Which form of bonding link checking are you using. It could be that bonding MII checking is confused.
I'm not specifying anything, just "ifenslave bond0 eth2 eth3"
Mike Stone
Do both ports report carrier present?
ethtool eth2
ethtool eth3
Signature · 1 line
Stephen Hemminger <[email protected]>
Re: [PATCH 4/4] skge: version 1.9
Quoted 3 lines · Stephen Hemminger
Do both ports report carrier present?
ethtool eth2
ethtool eth3
Link detected? yes
Mike Stone
Re: [PATCH 4/4] skge: version 1.9
In reply to Michael StoneQuoted 7 lines · Michael Stone
The skge 1.9 patch is looking good on older syskonnect fiber cards. Stability issues seem to be taken care of and performance is good. There are some strange interactions with bonding, however. If I try to put both interfaces of an sk-9844 into a bonded interface, I only see traffic from one of them. If I try to config the bonded interface down, the system hangs. If I tcpdump either of the individual interfaces (before bonding them) I see all the expected traffic.
Can you provide some bonding configuration details? Which mode,
options, etc, as well as the relevant bits from dmesg (you can send it to me privately if it's huge)? I don't have any skge hardware, so I'm not able to test this locally.
-J
---
-Jay Vosburgh, IBM Linux Technology Center, [email protected]
Re: [PATCH 4/4] skge: version 1.9
Quoted 3 lines · Jay Vosburgh
Can you provide some bonding configuration details? Which mode,
options, etc, as well as the relevant bits from dmesg (you can send it to me privately if it's huge)?
I think I sent another message that I'm just doing ifenslave bond0 eth2
ifenslave bond0 eth3
with no particular options set. The application is a network sniffer, and the cards are forced to 1000Mbps/full duplex because the other end doesn't negotiate. What's the relevant part of dmesg?
Mike Stone
Re: [PATCH 4/4] skge: version 1.9
Quoted 7 lines · Michael Stone
Quoted 3 lines · Jay Vosburgh
Can you provide some bonding configuration details? Which mode,
options, etc, as well as the relevant bits from dmesg (you can send it to me privately if it's huge)?I think I sent another message that I'm just doing ifenslave bond0 eth2 ifenslave bond0 eth3 with no particular options set.
I was thinking of the options to the bonding driver (probably in
the network configuration or /etc/modprobe.conf); a reasonable set of information is in /proc/net/bonding/bond0, so that's a good place to start, along with whatever "uname -a" prints (kernel version, architecture, mostly).
[...] The application is a network sniffer, and
Quoted 2 lines
the cards are forced to 1000Mbps/full duplex because the other end doesn't negotiate. What's the relevant part of dmesg?
Well, pretty much anything from the bonding driver or the
ethernet driver.
-J
---
-Jay Vosburgh, IBM Linux Technology Center, [email protected]