Skip to contentSkip to conversation

sky2: version 1.9 patches

PATCH New Stephen Hemminger 1 participant 13 messages Oct 11, 2006 – Oct 16, 2006

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

cover sky2: version 1.9 patches

Several little patches to sky2 driver. Mostly having to do with PHY handling and flow control.

#1 lore raw

PATCH 1/10 sky2: MSI test is only a warning

Some motherboards don't implement MSI correctly. The driver handles this but the warning is too verbose and overly cautious.

drivers/net/sky2.c +3 -3
@@ -3326,9 +3326,8 @@
 
 	if (!hw->msi_detected) {
 		/* MSI test failed, go back to INTx mode */
-		printk(KERN_WARNING PFX "%s: No interrupt was generated using MSI, "
-		       "switching to INTx mode. Please report this failure to "
-		       "the PCI maintainer and include system chipset information.\n",
+		printk(KERN_INFO PFX "%s: No interrupt generated using MSI, "
+		       "switching to INTx mode.\n",
 		       pci_name(pdev));
 
 		err = -EOPNOTSUPP;
@@ -3336,6 +3335,7 @@
 	}
 
 	sky2_write32(hw, B0_IMSK, 0);
+	sky2_read32(hw, B0_IMSK);
 
 	free_irq(pdev->irq, hw);
 

--
Stephen Hemminger <[email protected]>

#2 lore raw

PATCH 2/10 sky2: turn of workaround timer

In reply to Stephen Hemminger

The workaround timer is not needed in most systems with proper IRQ routing and by perodically waking up it adds to laptop power consumption.

---
 drivers/net/sky2.c |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/net/sky2.c +2 -2
@@ -96,9 +96,9 @@
 module_param(disable_msi, int, 0);
 MODULE_PARM_DESC(disable_msi, "Disable Message Signaled Interrupt (MSI)");
 
-static int idle_timeout = 100;
+static int idle_timeout = 0;
 module_param(idle_timeout, int, 0);
-MODULE_PARM_DESC(idle_timeout, "Idle timeout workaround for lost interrupts (ms)");
+MODULE_PARM_DESC(idle_timeout, "Watchdog timer for lost interrupts (ms)");
 
 static const struct pci_device_id sky2_id_table[] = {
 	{ PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9000) },

--
Stephen Hemminger <[email protected]>

#3 lore raw

PATCH 3/10 sky2: phy irq on shutdown

In reply to Stephen Hemminger

When PHY is turned off on shutdown, it causes the IRQ to get stuck on. Make sure and disable the IRQ first, and if IRQ occurs when device is not running, don't access PHY because that will hang.

drivers/net/sky2.c +8 -8
@@ -1499,6 +1499,11 @@
 	/* Stop more packets from being queued */
 	netif_stop_queue(dev);
 
+	/* Disable port IRQ */
+	imask = sky2_read32(hw, B0_IMSK);
+	imask &= ~portirq_msk[port];
+	sky2_write32(hw, B0_IMSK, imask);
+
 	sky2_gmac_reset(hw, port);
 
 	/* Stop transmitter */
@@ -1549,11 +1554,6 @@
 	sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_SET);
 	sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_RST_SET);
 
-	/* Disable port IRQ */
-	imask = sky2_read32(hw, B0_IMSK);
-	imask &= ~portirq_msk[port];
-	sky2_write32(hw, B0_IMSK, imask);
-
 	sky2_phy_power(hw, port, 0);
 
 	/* turn off LED's */
@@ -1750,13 +1750,13 @@
 	struct sky2_port *sky2 = netdev_priv(dev);
 	u16 istatus, phystat;
 
+	if (!netif_running(dev))
+		return;
+
 	spin_lock(&sky2->phy_lock);
 	istatus = gm_phy_read(hw, port, PHY_MARV_INT_STAT);
 	phystat = gm_phy_read(hw, port, PHY_MARV_PHY_STAT);
 
-	if (!netif_running(dev))
-		goto out;
-
 	if (netif_msg_intr(sky2))
 		printk(KERN_INFO PFX "%s: phy interrupt status 0x%x 0x%x\n",
 		       sky2->netdev->name, istatus, phystat);

--
Stephen Hemminger <[email protected]>

#4 lore raw

PATCH 4/10 sky2: fiber pause bits

In reply to Stephen Hemminger

The advertisement bits for flow control are located in different location on fiber (1000baseX)

drivers/net/sky2.c +19 -8
@@ -384,20 +384,31 @@
 				adv |= PHY_M_AN_10_FD;
 			if (sky2->advertising & ADVERTISED_10baseT_Half)
 				adv |= PHY_M_AN_10_HD;
+
+			/* desired flow control */
+			if (sky2->tx_pause && sky2->rx_pause)	/* both */
+				adv |= PHY_M_AN_PC | PHY_M_AN_ASP;
+			else if (sky2->tx_pause)
+				adv |= PHY_M_AN_ASP;
+			else if (sky2->rx_pause)
+				adv |= PHY_M_AN_PC;
+
+
 		} else {	/* special defines for FIBER (88E1040S only) */
 			if (sky2->advertising & ADVERTISED_1000baseT_Full)
 				adv |= PHY_M_AN_1000X_AFD;
 			if (sky2->advertising & ADVERTISED_1000baseT_Half)
 				adv |= PHY_M_AN_1000X_AHD;
-		}
 
-		/* Set Flow-control capabilities */
-		if (sky2->tx_pause && sky2->rx_pause)
-			adv |= PHY_AN_PAUSE_CAP;	/* symmetric */
-		else if (sky2->rx_pause && !sky2->tx_pause)
-			adv |= PHY_AN_PAUSE_ASYM | PHY_AN_PAUSE_CAP;
-		else if (!sky2->rx_pause && sky2->tx_pause)
-			adv |= PHY_AN_PAUSE_ASYM;	/* local */
+			if (sky2->tx_pause && sky2->rx_pause)	/* both */
+ 				adv |= PHY_M_P_BOTH_MD_X;
+			else if (sky2->tx_pause)
+				adv |= PHY_M_P_ASYM_MD_X;
+			else if (sky2->rx_pause)
+ 				adv |= PHY_M_P_SYM_MD_X;
+			else
+				adv |= PHY_M_P_NO_PAUSE_X;
+		}
 
 		/* Restart Auto-negotiation */
 		ctrl |= PHY_CT_ANE | PHY_CT_RE_CFG;

--
Stephen Hemminger <[email protected]>

#5 lore raw

PATCH 5/10 sky2: advertising register 16 bits

In reply to Stephen Hemminger

The advertising bits (from ethtool.h) fit in 16 bits.

drivers/net/sky2.h +1 -1
@@ -1860,7 +1860,7 @@
 
 	dma_addr_t	     rx_le_map;
 	dma_addr_t	     tx_le_map;
-	u32		     advertising;	/* ADVERTISED_ bits */
+	u16		     advertising;	/* ADVERTISED_ bits */
 	u16		     speed;	/* SPEED_1000, SPEED_100, ... */
 	u8		     autoneg;	/* AUTONEG_ENABLE, AUTONEG_DISABLE */
 	u8		     duplex;	/* DUPLEX_HALF, DUPLEX_FULL */

--
Stephen Hemminger <[email protected]>

#6 lore raw

PATCH 6/10 sky2: use duplex result bits

In reply to Stephen Hemminger

The result of duplex negotiation is avaliable in the phy status register, so use that to simplify code and avoid rereading the PHY.

---
 drivers/net/sky2.c |   21 +--------------------
 1 file changed, 1 insertion(+), 20 deletions(-)
drivers/net/sky2.c +1 -20
@@ -1714,26 +1714,7 @@
 	}
 
 	sky2->speed = sky2_phy_speed(hw, aux);
-	if (sky2->speed == SPEED_1000) {
-		u16 ctl2 = gm_phy_read(hw, port, PHY_MARV_1000T_CTRL);
-		u16 lpa2 = gm_phy_read(hw, port, PHY_MARV_1000T_STAT);
-		if (lpa2  & PHY_B_1000S_MSF) {
-			printk(KERN_ERR PFX "%s: master/slave fault",
-			       sky2->netdev->name);
-			return -1;
-		}
-
-		if ((ctl2 & PHY_M_1000C_AFD) && (lpa2 & PHY_B_1000S_LP_FD))
-			sky2->duplex = DUPLEX_FULL;
-		else
-			sky2->duplex = DUPLEX_HALF;
-	} else {
-		u16 adv = gm_phy_read(hw, port, PHY_MARV_AUNE_ADV);
-		if ((aux & adv) & PHY_AN_FULL)
-			sky2->duplex = DUPLEX_FULL;
-		else
-			sky2->duplex = DUPLEX_HALF;
-	}
+	sky2->duplex = (aux & PHY_M_PS_FULL_DUP) ? DUPLEX_FULL : DUPLEX_HALF;
 
 	/* Pause bits are offset (9..8) */
 	if (hw->chip_id == CHIP_ID_YUKON_XL || hw->chip_id == CHIP_ID_YUKON_EC_U)

--
Stephen Hemminger <[email protected]>

#7 lore raw

PATCH 7/10 sky2: dont reset PHY twice

In reply to Stephen Hemminger

Don't need to reset PHY twice on startup.

drivers/net/sky2.c +1 -12
@@ -356,16 +356,7 @@
 		gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
 	}
 
-	ctrl = gm_phy_read(hw, port, PHY_MARV_CTRL);
-	if (sky2->autoneg == AUTONEG_DISABLE)
-		ctrl &= ~PHY_CT_ANE;
-	else
-		ctrl |= PHY_CT_ANE;
-
-	ctrl |= PHY_CT_RESET;
-	gm_phy_write(hw, port, PHY_MARV_CTRL, ctrl);
-
-	ctrl = 0;
+	ctrl = PHY_CT_RESET;
 	ct1000 = 0;
 	adv = PHY_AN_CSMA;
 	reg = 0;
@@ -450,8 +441,6 @@
 			sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_ON);
 		else
 			sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_OFF);
-
-		ctrl |= PHY_CT_RESET;
 	}
 
 	gma_write16(hw, port, GM_GP_CTRL, reg);

--
Stephen Hemminger <[email protected]>

#8 lore raw

PATCH 8/10 sky2: flow control setting fixes

In reply to Stephen Hemminger

The result of flow control negotiation should not limit the next negotiatition. If board is plugged into an old half duplex 10Mbit port, without pause, then replugged into a gigabit port, it should negotiate what is desired, not inherit that last negotiation.

P.s: many other drivers have this bug.

---
 drivers/net/sky2.c |  132 ++++++++++++++++++++++++++++++-----------------------
 drivers/net/sky2.h |   13 ++++-
 2 files changed, 86 insertions(+), 59 deletions(-)
drivers/net/sky2.c +72 -43
@@ -284,6 +284,31 @@
 	gma_write16(hw, port, GM_RX_CTRL, reg);
 }
 
+/* flow control to advertise bits */
+static const u16 copper_fc_adv[] = {
+	[FC_NONE]	= 0,
+	[FC_TX]		= PHY_M_AN_ASP,
+	[FC_RX]		= PHY_M_AN_PC,
+	[FC_BOTH]	= PHY_M_AN_PC | PHY_M_AN_ASP,
+};
+
+/* flow control to advertise bits when using 1000BaseX */
+static const u16 fiber_fc_adv[] = {
+	[FC_BOTH] = PHY_M_P_BOTH_MD_X,
+	[FC_TX]   = PHY_M_P_ASYM_MD_X,
+	[FC_RX]	  = PHY_M_P_SYM_MD_X,
+	[FC_NONE] = PHY_M_P_NO_PAUSE_X,
+};
+
+/* flow control to GMA disable bits */
+static const u16 gm_fc_disable[] = {
+	[FC_NONE] = GM_GPCR_FC_RX_DIS | GM_GPCR_FC_TX_DIS,
+	[FC_TX]	  = GM_GPCR_FC_RX_DIS,
+	[FC_RX]	  = GM_GPCR_FC_TX_DIS,
+	[FC_BOTH] = 0,
+};
+
+
 static void sky2_phy_init(struct sky2_hw *hw, unsigned port)
 {
 	struct sky2_port *sky2 = netdev_priv(hw->dev[port]);
@@ -376,29 +401,14 @@
 			if (sky2->advertising & ADVERTISED_10baseT_Half)
 				adv |= PHY_M_AN_10_HD;
 
-			/* desired flow control */
-			if (sky2->tx_pause && sky2->rx_pause)	/* both */
-				adv |= PHY_M_AN_PC | PHY_M_AN_ASP;
-			else if (sky2->tx_pause)
-				adv |= PHY_M_AN_ASP;
-			else if (sky2->rx_pause)
-				adv |= PHY_M_AN_PC;
-
-
+			adv |= copper_fc_adv[sky2->flow_mode];
 		} else {	/* special defines for FIBER (88E1040S only) */
 			if (sky2->advertising & ADVERTISED_1000baseT_Full)
 				adv |= PHY_M_AN_1000X_AFD;
 			if (sky2->advertising & ADVERTISED_1000baseT_Half)
 				adv |= PHY_M_AN_1000X_AHD;
 
-			if (sky2->tx_pause && sky2->rx_pause)	/* both */
- 				adv |= PHY_M_P_BOTH_MD_X;
-			else if (sky2->tx_pause)
-				adv |= PHY_M_P_ASYM_MD_X;
-			else if (sky2->rx_pause)
- 				adv |= PHY_M_P_SYM_MD_X;
-			else
-				adv |= PHY_M_P_NO_PAUSE_X;
+			adv |= fiber_fc_adv[sky2->flow_mode];
 		}
 
 		/* Restart Auto-negotiation */
@@ -424,20 +434,14 @@
 		if (sky2->duplex == DUPLEX_FULL) {
 			reg |= GM_GPCR_DUP_FULL;
 			ctrl |= PHY_CT_DUP_MD;
-		} else if (sky2->speed != SPEED_1000 && hw->chip_id != CHIP_ID_YUKON_EC_U) {
-			/* Turn off flow control for 10/100mbps */
-			sky2->rx_pause = 0;
-			sky2->tx_pause = 0;
-		}
+		} else if (sky2->speed < SPEED_1000)
+			sky2->flow_mode = FC_NONE;
 
-		if (!sky2->rx_pause)
-			reg |= GM_GPCR_FC_RX_DIS;
 
-		if (!sky2->tx_pause)
-			reg |= GM_GPCR_FC_TX_DIS;
+ 		reg |= gm_fc_disable[sky2->flow_mode];
 
 		/* Forward pause packets to GMAC? */
-		if (sky2->tx_pause || sky2->rx_pause)
+		if (sky2->flow_mode & FC_RX)
 			sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_ON);
 		else
 			sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_OFF);
@@ -1605,6 +1609,12 @@
 	struct sky2_hw *hw = sky2->hw;
 	unsigned port = sky2->port;
 	u16 reg;
+	static const char *fc_name[] = {
+		[FC_NONE]	= "none",
+		[FC_TX]		= "tx",
+		[FC_RX]		= "rx",
+		[FC_BOTH]	= "both",
+	};
 
 	/* enable Rx/Tx */
 	reg = gma_read16(hw, port, GM_GP_CTRL);
@@ -1648,8 +1658,7 @@
 		       "%s: Link is up at %d Mbps, %s duplex, flow control %s\n",
 		       sky2->netdev->name, sky2->speed,
 		       sky2->duplex == DUPLEX_FULL ? "full" : "half",
-		       (sky2->tx_pause && sky2->rx_pause) ? "both" :
-		       sky2->tx_pause ? "tx" : sky2->rx_pause ? "rx" : "none");
+		       fc_name[sky2->flow_status]);
 }
 
 static void sky2_link_down(struct sky2_port *sky2)
@@ -1664,7 +1673,7 @@
 	reg &= ~(GM_GPCR_RX_ENA | GM_GPCR_TX_ENA);
 	gma_write16(hw, port, GM_GP_CTRL, reg);
 
-	if (sky2->rx_pause && !sky2->tx_pause) {
+	if (sky2->flow_status == FC_RX) {
 		/* restore Asymmetric Pause bit */
 		gm_phy_write(hw, port, PHY_MARV_AUNE_ADV,
 			     gm_phy_read(hw, port, PHY_MARV_AUNE_ADV)
@@ -1683,6 +1692,14 @@
 	sky2_phy_init(hw, port);
 }
 
+static enum flow_control sky2_flow(int rx, int tx)
+{
+	if (rx)
+		return tx ? FC_BOTH : FC_RX;
+	else
+		return tx ? FC_TX : FC_NONE;
+}
+
 static int sky2_autoneg_done(struct sky2_port *sky2, u16 aux)
 {
 	struct sky2_hw *hw = sky2->hw;
@@ -1709,14 +1726,14 @@
 	if (hw->chip_id == CHIP_ID_YUKON_XL || hw->chip_id == CHIP_ID_YUKON_EC_U)
 		aux >>= 6;
 
-	sky2->rx_pause = (aux & PHY_M_PS_RX_P_EN) != 0;
-	sky2->tx_pause = (aux & PHY_M_PS_TX_P_EN) != 0;
+	sky2->flow_status = sky2_flow(aux & PHY_M_PS_RX_P_EN,
+				      aux & PHY_M_PS_TX_P_EN);
 
-	if (sky2->duplex == DUPLEX_HALF && sky2->speed != SPEED_1000
+	if (sky2->duplex == DUPLEX_HALF && sky2->speed < SPEED_1000
 	    && hw->chip_id != CHIP_ID_YUKON_EC_U)
-		sky2->rx_pause = sky2->tx_pause = 0;
+		sky2->flow_status = FC_NONE;
 
-	if (sky2->rx_pause || sky2->tx_pause)
+	if (aux & PHY_M_PS_RX_P_EN)
 		sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_ON);
 	else
 		sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_OFF);
@@ -2729,7 +2746,7 @@
 {
 	struct sky2_port *sky2 = netdev_priv(dev);
 
-	if (sky2->autoneg != AUTONEG_ENABLE)
+	if (!netif_running(dev) || sky2->autoneg != AUTONEG_ENABLE)
 		return -EINVAL;
 
 	sky2_phy_reinit(sky2);
@@ -2971,8 +2988,20 @@
 {
 	struct sky2_port *sky2 = netdev_priv(dev);
 
-	ecmd->tx_pause = sky2->tx_pause;
-	ecmd->rx_pause = sky2->rx_pause;
+	switch (sky2->flow_mode) {
+	case FC_NONE:
+		ecmd->tx_pause = ecmd->rx_pause = 0;
+		break;
+	case FC_TX:
+		ecmd->tx_pause = 1, ecmd->rx_pause = 0;
+		break;
+	case FC_RX:
+		ecmd->tx_pause = 0, ecmd->rx_pause = 1;
+		break;
+	case FC_BOTH:
+		ecmd->tx_pause = ecmd->rx_pause = 1;
+	}
+
 	ecmd->autoneg = sky2->autoneg;
 }
 
@@ -2982,10 +3011,10 @@
 	struct sky2_port *sky2 = netdev_priv(dev);
 
 	sky2->autoneg = ecmd->autoneg;
-	sky2->tx_pause = ecmd->tx_pause != 0;
-	sky2->rx_pause = ecmd->rx_pause != 0;
+	sky2->flow_mode = sky2_flow(ecmd->rx_pause, ecmd->tx_pause);
 
-	sky2_phy_reinit(sky2);
+	if (netif_running(dev))
+		sky2_phy_reinit(sky2);
 
 	return 0;
 }
@@ -3215,8 +3244,8 @@
 
 	/* Auto speed and flow control */
 	sky2->autoneg = AUTONEG_ENABLE;
-	sky2->tx_pause = 1;
-	sky2->rx_pause = 1;
+	sky2->flow_mode = FC_BOTH;
+
 	sky2->duplex = -1;
 	sky2->speed = -1;
 	sky2->advertising = sky2_supported_modes(hw);
drivers/net/sky2.h +9 -2
@@ -1828,6 +1828,13 @@
 	dma_addr_t	frag_addr[ETH_JUMBO_MTU >> PAGE_SHIFT];
 };
 
+enum flow_control {
+	FC_NONE	= 0,
+	FC_TX	= 1,
+	FC_RX	= 2,
+	FC_BOTH	= 3,
+};
+
 struct sky2_port {
 	struct sky2_hw	     *hw;
 	struct net_device    *netdev;
@@ -1864,9 +1871,9 @@
 	u16		     speed;	/* SPEED_1000, SPEED_100, ... */
 	u8		     autoneg;	/* AUTONEG_ENABLE, AUTONEG_DISABLE */
 	u8		     duplex;	/* DUPLEX_HALF, DUPLEX_FULL */
-	u8		     rx_pause;
-	u8		     tx_pause;
 	u8		     rx_csum;
+ 	enum flow_control    flow_mode;
+ 	enum flow_control    flow_status;
 
 	struct net_device_stats net_stats;
 

--
Stephen Hemminger <[email protected]>

#9 lore raw

PATCH 9/10 sky2: no message on rx fifo overflow

In reply to Stephen Hemminger

Under high load it is possible to make the receiver FIFO get overloaded. The driver/hardware recover properly, so there is no reason to fill the log with lots of extra messages, just update counter.

---
 drivers/net/sky2.c |    6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)
drivers/net/sky2.c +4 -2
@@ -2014,6 +2014,10 @@
 
 error:
 	++sky2->net_stats.rx_errors;
+	if (status & GMR_FS_RX_FF_OV) {
+		sky2->net_stats.rx_fifo_errors++;
+		goto resubmit;
+	}
 
 	if (netif_msg_rx_err(sky2) && net_ratelimit())
 		printk(KERN_INFO PFX "%s: rx error, status 0x%x length %d\n",
@@ -2025,8 +2029,6 @@
 		sky2->net_stats.rx_frame_errors++;
 	if (status & GMR_FS_CRC_ERR)
 		sky2->net_stats.rx_crc_errors++;
-	if (status & GMR_FS_RX_FF_OV)
-		sky2->net_stats.rx_fifo_errors++;
 
 	goto resubmit;
 }

--
Stephen Hemminger <[email protected]>

#11 lore raw

PATCH 1/2 sky2: multicast pause frame receive

When using flow control, the PHY needs to accept multicast pause frames. Without this fix, these frames were getting discarded by the PHY before doing any flow control.

This maybe related to http://bugzilla.kernel.org/show_bug.cgi?id=6839

---
 drivers/net/sky2.c |   24 ++++++++++++++++++------
 1 file changed, 18 insertions(+), 6 deletions(-)
drivers/net/sky2.c +18 -6
@@ -2850,6 +2850,14 @@
 	return 0;
 }
 
+static void inline sky2_add_filter(u8 filter[8], const u8 *addr)
+{
+	u32 bit;
+
+	bit = ether_crc(ETH_ALEN, addr) & 63;
+	filter[bit >> 3] |= 1 << (bit & 7);
+}
+
 static void sky2_set_multicast(struct net_device *dev)
 {
 	struct sky2_port *sky2 = netdev_priv(dev);
@@ -2858,7 +2866,10 @@
 	struct dev_mc_list *list = dev->mc_list;
 	u16 reg;
 	u8 filter[8];
+	int rx_pause;
+	static const u8 pause_mc_addr[ETH_ALEN] = { 0x1, 0x80, 0xc2, 0x0, 0x0, 0x1 };
 
+	rx_pause = (sky2->flow_status == FC_RX || sky2->flow_status == FC_BOTH);
 	memset(filter, 0, sizeof(filter));
 
 	reg = gma_read16(hw, port, GM_RX_CTRL);
@@ -2866,18 +2877,19 @@
 
 	if (dev->flags & IFF_PROMISC)	/* promiscuous */
 		reg &= ~(GM_RXCR_UCF_ENA | GM_RXCR_MCF_ENA);
-	else if ((dev->flags & IFF_ALLMULTI) || dev->mc_count > 16)	/* all multicast */
+	else if (dev->flags & IFF_ALLMULTI)
 		memset(filter, 0xff, sizeof(filter));
-	else if (dev->mc_count == 0)	/* no multicast */
+	else if (dev->mc_count == 0 && !rx_pause)
 		reg &= ~GM_RXCR_MCF_ENA;
 	else {
 		int i;
 		reg |= GM_RXCR_MCF_ENA;
 
-		for (i = 0; list && i < dev->mc_count; i++, list = list->next) {
-			u32 bit = ether_crc(ETH_ALEN, list->dmi_addr) & 0x3f;
-			filter[bit / 8] |= 1 << (bit % 8);
-		}
+		if (rx_pause)
+			sky2_add_filter(filter, pause_mc_addr);
+
+		for (i = 0; list && i < dev->mc_count; i++, list = list->next)
+			sky2_add_filter(filter, list->dmi_addr);
 	}
 
 	gma_write16(hw, port, GM_MC_ADDR_H1,
#12 lore raw

PATCH 2/2 sky2: don't process pause frames in recveiver.

In reply to Stephen Hemminger

This reverts earlier change that attempted to fix flow control; but was broken.

Device needs to discard pause frames at the receive DMA engine, otherwise the pause frames get received and passed up the stack!

---
 drivers/net/sky2.h |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/net/sky2.h +1 -1
@@ -1576,7 +1576,7 @@
 
 	GMR_FS_ANY_ERR	= GMR_FS_RX_FF_OV | GMR_FS_CRC_ERR |
 			  GMR_FS_FRAGMENT | GMR_FS_LONG_ERR |
-		  	  GMR_FS_MII_ERR | GMR_FS_BAD_FC |
+		  	  GMR_FS_MII_ERR | GMR_FS_GOOD_FC | GMR_FS_BAD_FC |
 			  GMR_FS_UN_SIZE | GMR_FS_JABBER,
 };