2.6.19-rc5 x86_64 irq 22: nobody cared
Hi,
2.6.19-rc5 does not boot properly, I have tried pci=routeirq, irpoll without success.
Full details (.config, dmesg, /proc/interrupts) are in http://olivn.trollprod.org/2.6.19-rc5-irq.tar.gz
Olivier
System: ASUS M2N32-SLI, AMD64 X2 Dual Core 4600
kernel 2.6.9-rc5
irq 22: nobody cared (try booting with the "irqpoll" option)
Call Trace: <IRQ> [<ffffffff80259055>] __report_bad_irq+0x35/0x90 [<ffffffff802592d3>] note_interrupt+0x223/0x280 [<ffffffff80259d41>] handle_fasteoi_irq+0xb1/0xf0 [<ffffffff8020b17c>] call_softirq+0x1c/0x30 [<ffffffff8020d1ba>] do_IRQ+0x8a/0xe0 [<ffffffff8020a571>] ret_from_intr+0x0/0xa <EOI>
handlers:
[<ffffffff8807f150>] (nv_generic_interrupt+0x0/0xc0 [sata_nv]) Disabling IRQ #22
CPU0 CPU1
0: 223 45540 IO-APIC-edge timer 1: 1 402 IO-APIC-edge i8042 6: 1 4 IO-APIC-edge floppy 8: 0 0 IO-APIC-edge rtc 9: 0 0 IO-APIC-fasteoi acpi 12: 0 103 IO-APIC-edge i8042 14: 7 140 IO-APIC-edge ide0 16: 0 0 IO-APIC-fasteoi libata 17: 0 10 IO-APIC-fasteoi bttv0 20: 0 20 IO-APIC-fasteoi ehci_hcd:usb1 21: 0 0 IO-APIC-fasteoi libata 22: 214 99786 IO-APIC-fasteoi libata, HDA Intel 23: 76 6230 IO-APIC-fasteoi libata, ohci_hcd:usb2 308: 5 3169 PCI-MSI-edge eth1 309: 0 10 PCI-MSI-edge eth1 310: 0 44 PCI-MSI-edge eth1 311: 1 3193 PCI-MSI-edge eth0 312: 0 0 PCI-MSI-edge eth0 313: 0 1 PCI-MSI-edge eth0 NMI: 64 68 LOC: 45716 45691 ERR: 0
kernel 2.6.19-rc5 with pci=routeirq
irq 21: nobody cared (try booting with the "irqpoll" option)
Call Trace: <IRQ> [<ffffffff80259055>] __report_bad_irq+0x35/0x90 [<ffffffff802592d3>] note_interrupt+0x223/0x280 [<ffffffff80259d41>] handle_fasteoi_irq+0xb1/0xf0 [<ffffffff8020b17c>] call_softirq+0x1c/0x30 [<ffffffff8020d1ba>] do_IRQ+0x8a/0xe0 [<ffffffff802092f0>] default_idle+0x0/0x50 [<ffffffff8020a571>] ret_from_intr+0x0/0xa <EOI> [<ffffffff80209319>] default_idle+0x29/0x50 [<ffffffff8020939b>] cpu_idle+0x5b/0x80 [<ffffffff8050039c>] start_secondary+0x50c/0x520
handlers:
[<ffffffff880e6fd0>] (usb_hcd_irq+0x0/0x60 [usbcore]) Disabling IRQ #21
CPU0 CPU1
0: 214 24856 IO-APIC-edge timer 1: 0 359 IO-APIC-edge i8042 6: 0 5 IO-APIC-edge floppy 8: 0 0 IO-APIC-edge rtc 9: 0 0 IO-APIC-fasteoi acpi 12: 0 103 IO-APIC-edge i8042 14: 0 128 IO-APIC-edge ide0 16: 0 0 IO-APIC-fasteoi libata 17: 1 2 IO-APIC-fasteoi bttv0 20: 22 6469 IO-APIC-fasteoi libata 21: 11 99989 IO-APIC-fasteoi ehci_hcd:usb2, HDA Intel 22: 0 1 IO-APIC-fasteoi libata, ohci_hcd:usb1 23: 0 0 IO-APIC-fasteoi libata 308: 8 2378 PCI-MSI-edge eth1 309: 0 9 PCI-MSI-edge eth1 310: 0 9 PCI-MSI-edge eth1 311: 4 2401 PCI-MSI-edge eth0 312: 0 0 PCI-MSI-edge eth0 313: 0 1 PCI-MSI-edge eth0 NMI: 74 47 LOC: 25024 24991 ERR: 0
kernel 2.6.19-rc5 with irqpoll
Hang during boot
(See screenshot in http://olivn.trollprod.org/2.6.19-rc5-irq.tar.gz)
kernel 2.6.18 (works without any problem)
CPU0 CPU1
0: 1590 998089 IO-APIC-edge timer 1: 2 657 IO-APIC-edge i8042 6: 0 5 IO-APIC-edge floppy 8: 0 0 IO-APIC-edge rtc 9: 0 0 IO-APIC-level acpi 12: 194 59353 IO-APIC-edge i8042 14: 13 6381 IO-APIC-edge ide0 50: 0 0 IO-APIC-level libata 58: 0 0 IO-APIC-level libata 66: 109 181425 IO-APIC-level libata, nvidia 74: 41 963 IO-APIC-level ehci_hcd:usb1, HDA Intel 82: 4 6 IO-APIC-level bttv0 90: 0 0 PCI-MSI-X eth0 98: 3 0 PCI-MSI-X eth0 106: 212234 0 PCI-MSI-X eth0 114: 532 0 PCI-MSI-X eth1 122: 445 0 PCI-MSI-X eth1 130: 212217 0 PCI-MSI-X eth1 233: 73 23009 IO-APIC-level libata, ohci_hcd:usb2 NMI: 99 104 LOC: 999684 999664 ERR: 0 MIS: 0
Quoted 1 line · Olivier Nicolas
Hi,
Hi Olivier,
Quoted 5 lines
2.6.19-rc5 does not boot properly, I have tried pci=routeirq, irpoll without success.
Full details (.config, dmesg,
/proc/interrupts) are in
http://olivn.trollprod.org/2.6.19-rc5-irq.tar.gz
thanks for your report!
I might be wrong, but looking at the dmesg:
- irq 22 is the hda_intel IRQ
- the "irq 22: nobody cared" is immediately before the "hda_intel: No response from codec, disabling MSI..."
- in the routeirq case, the hda_intel IRQ as well as the IRQ in the error message change to 21
So it might be related to the hda_intel MSI check.
If this was a wrong guess, other interesting messages in the dmesg are:
<-- snip -->
...
PCI: Using MMCONFIG at f0000000
PCI: No mmconfig possible on device 00:18
...
PCI: Setting latency timer of device 0000:00:03.0 to 64 pcie_portdrv_probe->Dev[02fd:10de] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:03.0:pcie00]
Allocate Port Service[0000:00:03.0:pcie03]
PCI: Setting latency timer of device 0000:00:04.0 to 64 pcie_portdrv_probe->Dev[02fb:10de] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:04.0:pcie00]
Allocate Port Service[0000:00:04.0:pcie03]
PCI: Setting latency timer of device 0000:00:12.0 to 64 pcie_portdrv_probe->Dev[0376:10de] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:12.0:pcie00]
Allocate Port Service[0000:00:12.0:pcie03]
PCI: Setting latency timer of device 0000:00:14.0 to 64 pcie_portdrv_probe->Dev[0374:10de] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:14.0:pcie00]
Allocate Port Service[0000:00:14.0:pcie03]
PCI: Setting latency timer of device 0000:00:16.0 to 64 pcie_portdrv_probe->Dev[0375:10de] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:16.0:pcie00]
Allocate Port Service[0000:00:16.0:pcie03]
PCI: Setting latency timer of device 0000:00:17.0 to 64 pcie_portdrv_probe->Dev[0377:10de] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:17.0:pcie00]
Allocate Port Service[0000:00:17.0:pcie03]
...
<-- snip -->
Quoted 127 lines
Olivier
System: ASUS M2N32-SLI, AMD64 X2 Dual Core 4600
kernel 2.6.9-rc5
irq 22: nobody cared (try booting with the "irqpoll" option)
Call Trace: <IRQ> [<ffffffff80259055>] __report_bad_irq+0x35/0x90 [<ffffffff802592d3>] note_interrupt+0x223/0x280 [<ffffffff80259d41>] handle_fasteoi_irq+0xb1/0xf0 [<ffffffff8020b17c>] call_softirq+0x1c/0x30 [<ffffffff8020d1ba>] do_IRQ+0x8a/0xe0 [<ffffffff8020a571>] ret_from_intr+0x0/0xa <EOI>handlers:
[<ffffffff8807f150>] (nv_generic_interrupt+0x0/0xc0[sata_nv]) Disabling IRQ #22CPU0 CPU1
0: 223 45540 IO-APIC-edge timer 1: 1 402 IO-APIC-edge i8042 6: 1 4 IO-APIC-edge floppy 8: 0 0 IO-APIC-edge rtc 9: 0 0 IO-APIC-fasteoi acpi 12: 0 103 IO-APIC-edge i8042 14: 7 140 IO-APIC-edge ide0 16: 0 0 IO-APIC-fasteoi libata 17: 0 10 IO-APIC-fasteoi bttv0 20: 0 20 IO-APIC-fasteoi ehci_hcd:usb1 21: 0 0 IO-APIC-fasteoi libata 22: 214 99786 IO-APIC-fasteoi libata, HDA Intel 23: 76 6230 IO-APIC-fasteoi libata, ohci_hcd:usb2 308: 5 3169 PCI-MSI-edge eth1 309: 0 10 PCI-MSI-edge eth1 310: 0 44 PCI-MSI-edge eth1 311: 1 3193 PCI-MSI-edge eth0 312: 0 0 PCI-MSI-edge eth0 313: 0 1 PCI-MSI-edge eth0 NMI: 64 68 LOC: 45716 45691 ERR: 0kernel 2.6.19-rc5 with pci=routeirq
irq 21: nobody cared (try booting with the "irqpoll" option)
Call Trace: <IRQ> [<ffffffff80259055>] __report_bad_irq+0x35/0x90 [<ffffffff802592d3>] note_interrupt+0x223/0x280 [<ffffffff80259d41>] handle_fasteoi_irq+0xb1/0xf0 [<ffffffff8020b17c>] call_softirq+0x1c/0x30 [<ffffffff8020d1ba>] do_IRQ+0x8a/0xe0 [<ffffffff802092f0>] default_idle+0x0/0x50 [<ffffffff8020a571>] ret_from_intr+0x0/0xa <EOI> [<ffffffff80209319>] default_idle+0x29/0x50 [<ffffffff8020939b>] cpu_idle+0x5b/0x80 [<ffffffff8050039c>] start_secondary+0x50c/0x520handlers:
[<ffffffff880e6fd0>] (usb_hcd_irq+0x0/0x60[usbcore]) Disabling IRQ #21CPU0 CPU1
0: 214 24856 IO-APIC-edge timer 1: 0 359 IO-APIC-edge i8042 6: 0 5 IO-APIC-edge floppy 8: 0 0 IO-APIC-edge rtc 9: 0 0 IO-APIC-fasteoi acpi 12: 0 103 IO-APIC-edge i8042 14: 0 128 IO-APIC-edge ide0 16: 0 0 IO-APIC-fasteoi libata 17: 1 2 IO-APIC-fasteoi bttv0 20: 22 6469 IO-APIC-fasteoi libata 21: 11 99989 IO-APIC-fasteoi ehci_hcd:usb2, HDA Intel 22: 0 1 IO-APIC-fasteoi libata, ohci_hcd:usb1 23: 0 0 IO-APIC-fasteoi libata 308: 8 2378 PCI-MSI-edge eth1 309: 0 9 PCI-MSI-edge eth1 310: 0 9 PCI-MSI-edge eth1 311: 4 2401 PCI-MSI-edge eth0 312: 0 0 PCI-MSI-edge eth0 313: 0 1 PCI-MSI-edge eth0 NMI: 74 47 LOC: 25024 24991 ERR: 0kernel 2.6.19-rc5 with irqpoll
Hang during boot
(See screenshot in http://olivn.trollprod.org/2.6.19-rc5-irq.tar.gz)kernel 2.6.18 (works without any problem)
CPU0 CPU1
0: 1590 998089 IO-APIC-edge timer 1: 2 657 IO-APIC-edge i8042 6: 0 5 IO-APIC-edge floppy 8: 0 0 IO-APIC-edge rtc 9: 0 0 IO-APIC-level acpi 12: 194 59353 IO-APIC-edge i8042 14: 13 6381 IO-APIC-edge ide0 50: 0 0 IO-APIC-level libata 58: 0 0 IO-APIC-level libata 66: 109 181425 IO-APIC-level libata, nvidia 74: 41 963 IO-APIC-level ehci_hcd:usb1, HDA Intel 82: 4 6 IO-APIC-level bttv0 90: 0 0 PCI-MSI-X eth0 98: 3 0 PCI-MSI-X eth0 106: 212234 0 PCI-MSI-X eth0 114: 532 0 PCI-MSI-X eth1 122: 445 0 PCI-MSI-X eth1 130: 212217 0 PCI-MSI-X eth1 233: 73 23009 IO-APIC-level libata, ohci_hcd:usb2 NMI: 99 104 LOC: 999684 999664 ERR: 0 MIS: 0
olivier,
lspci -vvxxx please.
it seems usb and audio share the interrtupts by ioapic.
YH
Quoted 7 lines · Yinghai Lu
olivier,
lspci -vvxxx please.
it seems usb and audio share the interrtupts by ioapic.
YH
lspci -vvxxx is available at http://olivn.trollprod.org/lspci.gz
2.6.19-rc5 can be booted properly on my system if "notsc" parameter is used.
Could it be related to http://lkml.org/lkml/2006/10/27/141 as I'm usage a dual core AMD64 ?
Olivier
At Thu, 9 Nov 2006 07:49:56 +0100,
Quoted 15 lines · Adrian Bunk
Quoted 1 line · Olivier Nicolas
Hi,
Hi Olivier,
Quoted 5 lines
2.6.19-rc5 does not boot properly, I have tried pci=routeirq, irpoll without success.
Full details (.config, dmesg,
/proc/interrupts) are in
http://olivn.trollprod.org/2.6.19-rc5-irq.tar.gzthanks for your report!
Quoted 8 lines
I might be wrong, but looking at the dmesg:
- irq 22 is thehda_intelIRQ
- the "irq 22: nobody cared" is immediately before the "hda_intel: No response from codec, disabling MSI..."
- in the routeirq case, thehda_intelIRQ as well as the IRQ in the error message change to 21So it might be related to the
hda_intelMSI check.
To disable MSI from the beginning, set disable_msi=1 module option for snd-hda-intel.
Takashi
Takashi,
You are right, setting disable_msi=1 as an option for snd-hda-intel module solve my problem.
Thanks
Olivier
Quoted 26 lines · Takashi Iwai
At Thu, 9 Nov 2006 07:49:56 +0100,
Quoted 10 lines · Adrian Bunk
Quoted 1 line · Olivier Nicolas
Hi,
Hi Olivier,
Quoted 3 lines
2.6.19-rc5 does not boot properly, I have tried pci=routeirq, irpoll without success.
Full details (.config, dmesg,
/proc/interrupts) are in http://olivn.trollprod.org/2.6.19-rc5-irq.tar.gzthanks for your report!
Quoted 8 lines
I might be wrong, but looking at the dmesg:
- irq 22 is thehda_intelIRQ
- the "irq 22: nobody cared" is immediately before the "hda_intel: No response from codec, disabling MSI..."
- in the routeirq case, thehda_intelIRQ as well as the IRQ in the error message change to 21So it might be related to the
hda_intelMSI check.To disable MSI from the beginning, set disable_msi=1 module option for snd-hda-intel.
Takashi
Quoted 14 lines · On Thu, 9 Nov 2006 07:49:56 +0100 Adrian Bunk <[email protected]> wrote:
Quoted 1 line · Olivier Nicolas
Hi,
Hi Olivier,
Quoted 5 lines
2.6.19-rc5 does not boot properly, I have tried pci=routeirq, irpoll without success.
Full details (.config, dmesg,
/proc/interrupts) are in
http://olivn.trollprod.org/2.6.19-rc5-irq.tar.gzthanks for your report!
Quoted 8 lines
I might be wrong, but looking at the dmesg:
- irq 22 is thehda_intelIRQ
- the "irq 22: nobody cared" is immediately before the "hda_intel: No response from codec, disabling MSI..."
- in the routeirq case, thehda_intelIRQ as well as the IRQ in the error message change to 21So it might be related to the
hda_intelMSI check.
More likely the MSI management routines don't work for disabling MSI. I am debugging a problem where MSI doesn't work across suspend/resume, I suspect the base MSI code needs fixing.
Signature · 1 line
Stephen Hemminger <[email protected]>
Quoted 24 lines · Stephen Hemminger
Quoted 21 lines · On Thu, 9 Nov 2006 07:49:56 +0100 Adrian Bunk <[email protected]> wrote:
Quoted 1 line · Olivier Nicolas
Hi,
Hi Olivier,
Quoted 5 lines
2.6.19-rc5 does not boot properly, I have tried pci=routeirq, irpoll without success.
Full details (.config, dmesg,
/proc/interrupts) are in
http://olivn.trollprod.org/2.6.19-rc5-irq.tar.gzthanks for your report!
I might be wrong, but looking at the dmesg:
- irq 22 is thehda_intelIRQ
- the "irq 22: nobody cared" is immediately before the "hda_intel: No response from codec, disabling MSI..."
- in the routeirq case, thehda_intelIRQ as well as the IRQ in the error message change to 21
Quoted 3 lines
Quoted 1 line
So it might be related to the
hda_intelMSI check.More likely the MSI management routines don't work for disabling MSI.
Well brand new MSI handling could be buggy, the disable hypothesis doesn't make much sense on boot up.
Quoted 2 lines
I am debugging a problem where MSI doesn't work across suspend/resume, I suspect the base MSI code needs fixing.
Rethinking the interfaces maybe I don't think the code is broken I think most likely it is just not designed to do the right thing. I remember thinking how horrible that code is, when I read through it.
Eric
Quoted 4 lines · Olivier Nicolas
Hi,
2.6.19-rc5 does not boot properly, I have tried pci=routeirq, irpoll without success.
Still a problem with pci=nomsi removing all those MSI NICs from the picture? pci=nommconf is also popular these days:-)
-Len