Skip to contentSkip to conversation

libata: use FLUSH_EXT only when driver is larger than LBA28 limit

PATCH In review Tejun Heo 3 participants 5 messages Nov 10, 2006 – Nov 14, 2006 libata

lore
Share & tools
lore

Tejun Heo

author
#0 lore raw

PATCH 1/1 libata: use FLUSH_EXT only when driver is larger than LBA28 limit

Many drives support LBA48 even when its capacity is smaller than 1<<28, as LBA48 is required for many functionalities. FLUSH_EXT is mandatory for drives w/ LBA48 support.

Interestingly, at least one of such drives (ST960812A) has problems dealing with FLUSH_EXT. It eventually completes the command but takes around 7 seconds to finish in many cases thus drastically slowing down IO transactions. This seems to be a firmware bug which sneaked into production probably because no other ATA driver including linux IDE issues FLUSH_EXT to drives which report support for LBA48 & FLUSH_EXT but is smaller than 1<<28 blocks.

This patch adds ATA_DFLAG_FLUSH_EXT which is set iff the drive supports LBA48 & FLUSH_EXT and is larger than LBA28 limit. Both cache flush paths are updated to issue FLUSH_EXT only when the flag is set. Note that the changed behavior is more inline with the rest of libata. libata prefers shorter commands whenever possible.

Cc Danny Kukawka <[email protected]>
Cc Stefan Seyfried <[email protected]>
drivers/ata/libata-core.c +5 -1
index 9fdb266..669ee26 100644
@@ -1457,6 +1457,10 @@ int ata_dev_configure(struct ata_device
 			if (ata_id_has_lba48(id)) {
 				dev->flags |= ATA_DFLAG_LBA48;
 				lba_desc = "LBA48";
+
+				if (ata_id_u64(id, 100) >= (1UL << 28) &&
+				    ata_id_has_flush_ext(id))
+					dev->flags |= ATA_DFLAG_FLUSH_EXT;
 			}
 
 			/* config NCQ */
@@ -5128,7 +5132,7 @@ int ata_flush_cache(struct ata_device *d
 	if (!ata_try_flush_cache(dev))
 		return 0;
 
-	if (ata_id_has_flush_ext(dev->id))
+	if (dev->flags & ATA_DFLAG_FLUSH_EXT)
 		cmd = ATA_CMD_FLUSH_EXT;
 	else
 		cmd = ATA_CMD_FLUSH;
drivers/ata/libata-scsi.c +1 -2
index a0b6ee1..2be51c6 100644
@@ -1027,8 +1027,7 @@ static unsigned int ata_scsi_flush_xlat(
 	tf->flags |= ATA_TFLAG_DEVICE;
 	tf->protocol = ATA_PROT_NODATA;
 
-	if ((qc->dev->flags & ATA_DFLAG_LBA48) &&
-	    (ata_id_has_flush_ext(qc->dev->id)))
+	if (qc->dev->flags & ATA_DFLAG_FLUSH_EXT)
 		tf->command = ATA_CMD_FLUSH_EXT;
 	else
 		tf->command = ATA_CMD_FLUSH;
include/linux/libata.h +1 -0
index 0d0ddea..36e233c 100644
@@ -140,6 +140,7 @@ enum {
 	ATA_DFLAG_LBA48		= (1 << 1), /* device supports LBA48 */
 	ATA_DFLAG_CDB_INTR	= (1 << 2), /* device asserts INTRQ when ready for CDB */
 	ATA_DFLAG_NCQ		= (1 << 3), /* device supports NCQ */
+	ATA_DFLAG_FLUSH_EXT	= (1 << 4), /* do FLUSH_EXT instead of FLUSH */
 	ATA_DFLAG_CFG_MASK	= (1 << 8) - 1,
 
 	ATA_DFLAG_PIO		= (1 << 8), /* device limited to PIO mode */
author
#1 lore raw
Quoted 12 lines · Tejun Heo

Many drives support LBA48 even when its capacity is smaller than 1<<28, as LBA48 is required for many functionalities. FLUSH_EXT is mandatory for drives w/ LBA48 support.

Interestingly, at least one of such drives (ST960812A) has problems dealing with FLUSH_EXT. It eventually completes the command but takes around 7 seconds to finish in many cases thus drastically slowing down IO transactions. This seems to be a firmware bug which sneaked into production probably because no other ATA driver including linux IDE issues FLUSH_EXT to drives which report support for LBA48 & FLUSH_EXT but is smaller than 1<<28 blocks.

Quoted 5 lines

This patch adds ATA_DFLAG_FLUSH_EXT which is set iff the drive supports LBA48 & FLUSH_EXT and is larger than LBA28 limit. Both cache flush paths are updated to issue FLUSH_EXT only when the flag is set. Note that the changed behavior is more inline with the rest of libata. libata prefers shorter commands whenever possible.

Jeff, I think this should go into #uptream-fixes, too. We shouldn't have issued FLUSH_EXT to < 1<<28 devices in the first place.

Thanks.

Signature · 1 line
tejun
#2 lore raw
In reply to Tejun Heo
Quoted 7 lines · Tejun Heo

Interestingly, at least one of such drives (ST960812A) has problems dealing with FLUSH_EXT. It eventually completes the command but takes around 7 seconds to finish in many cases thus drastically slowing down IO transactions. This seems to be a firmware bug which sneaked into production probably because no other ATA driver including linux IDE issues FLUSH_EXT to drives which report support for LBA48 & FLUSH_EXT but is smaller than 1<<28 blocks.

Note that i'm quite sure that i have seen this on more than this single drive. It might be that those were all seagates, though.

Signature · 3 lines
Stefan Seyfried
QA / R&D Team Mobile Devices        |              "Any ideas, John?"
SUSE LINUX Products GmbH, Nürnberg  | "Well, surrounding them's out." 
author
#3 lore raw

PATCH 1/1 libata: use FLUSH_EXT only when driver is larger than LBA28 limit

In reply to Tejun Heo

Many drives support LBA48 even when its capacity is smaller than 1<<28, as LBA48 is required for many functionalities. FLUSH_EXT is mandatory for drives w/ LBA48 support.

Interestingly, at least one of such drives (ST960812A) has problems dealing with FLUSH_EXT. It eventually completes the command but takes around 7 seconds to finish in many cases thus drastically slowing down IO transactions. This seems to be a firmware bug which sneaked into production probably because no other ATA driver including linux IDE issues FLUSH_EXT to drives which report support for LBA48 & FLUSH_EXT but is smaller than 1<<28 blocks.

This patch adds ATA_DFLAG_FLUSH_EXT which is set iff the drive supports LBA48 & FLUSH_EXT and is larger than LBA28 limit. Both cache flush paths are updated to issue FLUSH_EXT only when the flag is set. Note that the changed behavior is more inline with the rest of libata. libata prefers shorter commands whenever possible.

Cc Danny Kukawka <[email protected]>
Cc Stefan Seyfried <[email protected]>

---

* In ata_dev_configure(), use dev->n_sectors instead of reading it directly from id.

drivers/ata/libata-core.c +5 -1
index 9fdb266..e161036 100644
@@ -1457,6 +1457,10 @@ int ata_dev_configure(struct ata_device
 			if (ata_id_has_lba48(id)) {
 				dev->flags |= ATA_DFLAG_LBA48;
 				lba_desc = "LBA48";
+
+				if (dev->n_sectors >= (1UL << 28) &&
+				    ata_id_has_flush_ext(id))
+					dev->flags |= ATA_DFLAG_FLUSH_EXT;
 			}
 
 			/* config NCQ */
@@ -5128,7 +5132,7 @@ int ata_flush_cache(struct ata_device *d
 	if (!ata_try_flush_cache(dev))
 		return 0;
 
-	if (ata_id_has_flush_ext(dev->id))
+	if (dev->flags & ATA_DFLAG_FLUSH_EXT)
 		cmd = ATA_CMD_FLUSH_EXT;
 	else
 		cmd = ATA_CMD_FLUSH;
drivers/ata/libata-scsi.c +1 -2
index a0b6ee1..2be51c6 100644
@@ -1027,8 +1027,7 @@ static unsigned int ata_scsi_flush_xlat(
 	tf->flags |= ATA_TFLAG_DEVICE;
 	tf->protocol = ATA_PROT_NODATA;
 
-	if ((qc->dev->flags & ATA_DFLAG_LBA48) &&
-	    (ata_id_has_flush_ext(qc->dev->id)))
+	if (qc->dev->flags & ATA_DFLAG_FLUSH_EXT)
 		tf->command = ATA_CMD_FLUSH_EXT;
 	else
 		tf->command = ATA_CMD_FLUSH;
include/linux/libata.h +1 -0
index 0d0ddea..36e233c 100644
@@ -140,6 +140,7 @@ enum {
 	ATA_DFLAG_LBA48		= (1 << 1), /* device supports LBA48 */
 	ATA_DFLAG_CDB_INTR	= (1 << 2), /* device asserts INTRQ when ready for CDB */
 	ATA_DFLAG_NCQ		= (1 << 3), /* device supports NCQ */
+	ATA_DFLAG_FLUSH_EXT	= (1 << 4), /* do FLUSH_EXT instead of FLUSH */
 	ATA_DFLAG_CFG_MASK	= (1 << 8) - 1,
 
 	ATA_DFLAG_PIO		= (1 << 8), /* device limited to PIO mode */
#4 lore raw
Quoted 18 lines · Tejun Heo

Many drives support LBA48 even when its capacity is smaller than 1<<28, as LBA48 is required for many functionalities. FLUSH_EXT is mandatory for drives w/ LBA48 support.

Interestingly, at least one of such drives (ST960812A) has problems dealing with FLUSH_EXT. It eventually completes the command but takes around 7 seconds to finish in many cases thus drastically slowing down IO transactions. This seems to be a firmware bug which sneaked into production probably because no other ATA driver including linux IDE issues FLUSH_EXT to drives which report support for LBA48 & FLUSH_EXT but is smaller than 1<<28 blocks.

This patch adds ATA_DFLAG_FLUSH_EXT which is set iff the drive supports LBA48 & FLUSH_EXT and is larger than LBA28 limit. Both cache flush paths are updated to issue FLUSH_EXT only when the flag is set. Note that the changed behavior is more inline with the rest of libata. libata prefers shorter commands whenever possible.

Quoted 7 lines
Cc Danny Kukawka <[email protected]>
Cc Stefan Seyfried <[email protected]>

---

* In ata_dev_configure(), use dev->n_sectors instead of reading it directly from id.

applied to #upstream -- I think this wants more testing than 2.6.19-rc5 will allow