Skip to contentSkip to conversation

add numa node information to struct device

PATCH In review Christoph Hellwig 2 participants 2 messages Nov 15, 2006

Subsystems (5)
lore
Share & tools
lore
#0 lore raw

PATCH 2/3 add numa node information to struct device

For node-aware skb allocations we need information about the node in struct net_device or struct device. Davem suggested to put it into struct device which this patch does.

In particular:

- struct device gets a new int numa_node member if CONFIG_NUMA is set
- there are two new helpers, dev_to_node and set_dev_node to transparently deal with the non-numa case
- for pci devices the node-info is set to the value we get from pcibus_to_node.

Note that for some architectures pcibus_to_node doesn't work yet at the time we call it currently. This is harmless and will just mean skb allocations aren't node-local on this architectures until the implementation of pcibus_to_node on these architectures have been updated (There are patches for x86 and x86_64 floating around)

include/linux/device.h +11 -0
Index: linux-2.6/include/linux/device.h
===================================================================
@@ -347,6 +347,9 @@
 					   BIOS data),reserved for device core*/
 	struct dev_pm_info	power;
 
+#ifdef CONFIG_NUMA
+	int		numa_node;	/* NUMA node this device is close to */
+#endif
 	u64		*dma_mask;	/* dma mask (if dma'able device) */
 	u64		coherent_dma_mask;/* Like dma_mask, but for
 					     alloc_coherent mappings as
@@ -368,6 +371,14 @@
 	void	(*release)(struct device * dev);
 };
 
+#ifdef CONFIG_NUMA
+#define dev_to_node(dev)	((dev)->numa_node)
+#define set_dev_node(dev, node)	((dev)->numa_node = node)
+#else
+#define dev_to_node(dev)	(-1)
+#define set_dev_node(dev, node)	do { } while (0)
+#endif
+
 static inline void *
 dev_get_drvdata (struct device *dev)
 {
drivers/base/core.c +1 -0
Index: linux-2.6/drivers/base/core.c
===================================================================
@@ -381,6 +381,7 @@
 	INIT_LIST_HEAD(&dev->node);
 	init_MUTEX(&dev->sem);
 	device_init_wakeup(dev, 0);
+	set_dev_node(dev, -1);
 }
 
 /**
drivers/pci/probe.c +1 -0
Index: linux-2.6/drivers/pci/probe.c
===================================================================
@@ -846,6 +846,7 @@
 	dev->dev.release = pci_release_dev;
 	pci_dev_get(dev);
 
+	set_dev_node(&dev->dev, pcibus_to_node(bus));
 	dev->dev.dma_mask = &dev->dma_mask;
 	dev->dev.coherent_dma_mask = 0xffffffffull;
 

--
To unsubscribe, send a message with 'unsubscribe linux-mm' in the body to [email protected]. For more info on Linux MM,
see: http://www.linux-mm.org/ .
Don't email: <a href=mailto:"[email protected]"> [email protected] </a>

#1 lore raw

include/linux/device.h line 380

Quoted 7 lines · On Wed, 15 Nov 2006 18:37:01 +0100 Christoph Hellwig <[email protected]> wrote:
include/linux/device.h +7 -0
+#ifdef CONFIG_NUMA
+#define dev_to_node(dev)	((dev)->numa_node)
+#define set_dev_node(dev, node)	((dev)->numa_node = node)
+#else
+#define dev_to_node(dev)	(-1)
+#define set_dev_node(dev, node)	do { } while (0)
+#endif

minor point: using inlines here would give typechecking, prevent possible unused-var warnings, etc.

Maybe there was a reason for not doing that.

<does it>

No doubt I'll find out ;)

--
To unsubscribe, send a message with 'unsubscribe linux-mm' in the body to [email protected]. For more info on Linux MM,
see: http://www.linux-mm.org/ .
Don't email: <a href=mailto:"[email protected]"> [email protected] </a>