Skip to contentSkip to conversation

Is ircomm possible with smsc_ircc2?

DISCUSSION Andrey Borzenkov 2 participants 2 messages Nov 19, 2006 – Nov 27, 2006

lore
Share & tools
lore
#0 lore raw

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

I have Toshiba Portege 4000, which apparently needs smsc_ircc2 driver. Driver seems to load OK:

Detected unconfigured Toshiba laptop with ALi ISA bridge SMSC IrDA chip, pre-configuring device.
Activated ALi 1533 ISA bridge port 0x02e8.
Activated ALi 1533 ISA bridge port 0x02f8.
found SMC SuperIO Chip (devid=0x5a rev=00 base=0x002e): LPC47N227 smsc_superio_flat(): IrDA not enabled
smsc_superio_flat(): fir: 0x2f8, sir: 0x2e8, dma: 03, irq: 7, mode: 0x02 SMsC IrDA Controller found
IrCC version 2.0, firport 0x2f8, sirport 0x2e8 dma=3, irq=7
No transceiver found. Defaulting to Fast pin select

and it registers irda0 interface but no /dev/ircomm* ever appears. I need them (or at least I /think/ I need them) for SynCE (for installing programs in my Pocket LOOX).

What is missing? Do I need additional driver? How can I access ircomm on this HW?

TIA

- -andrey
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.5 (GNU/Linux)

iD8DBQFFYBLvR6LMutpd94wRAkuOAKC1f7GQ0AeL9xHcJEsMNn0AT9MIOQCglvcL YEZSnauoxed4K8uPpAMdKtw=
=jU1k
-----END PGP SIGNATURE-----

#1 lore raw
Quoted 15 lines · Andrey Borzenkov

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

I have Toshiba Portege 4000, which apparently needs smsc_ircc2 driver. Driver seems to load OK:

Detected unconfigured Toshiba laptop with ALi ISA bridge SMSC IrDA chip, pre-configuring device. Activated ALi 1533 ISA bridge port 0x02e8.
Activated ALi 1533 ISA bridge port 0x02f8.
found SMC SuperIO Chip (devid=0x5a rev=00 base=0x002e): LPC47N227 smsc_superio_flat(): IrDA not enabled
smsc_superio_flat(): fir: 0x2f8, sir: 0x2e8, dma: 03, irq: 7, mode: 0x02
SMsC IrDA Controller found
IrCC version 2.0, firport 0x2f8, sirport 0x2e8 dma=3, irq=7
No transceiver found. Defaulting to Fast pin select

Quoted 3 lines

and it registers irda0 interface but no /dev/ircomm* ever appears. I need them (or at least I /think/ I need them) for SynCE (for installing programs in my Pocket LOOX).

What is missing? Do I need additional driver? How can I access ircomm on this HW?

You probably need to load the ircomm-tty and ircomm modules on top of irda stack for /dev/ircomm*.

Best regards,
hinko

Signature · 7 lines
ČETRTA POT, d.o.o., Kranj
Planina 3
4000 Kranj
Slovenija
Tel. +386 (0) 4 280 66 37
E-mail: [email protected]
Http: www.cetrtapot.si