Skip to contentSkip to conversation

trying pata_ali in 2.6.19

DISCUSSION ron moncreiff 2 participants 2 messages Dec 1, 2006

lore
Share & tools
lore
#0 lore raw

// I have tried out the new pata options in the 2.6.19 kernel and had some problems. // // So here's the skinny. I am using the asrock 939dual - sataII mobo. lspci reports // // the IDE interface thus: //

00:12.0 IDE interface: ALi Corporation M5229 IDE (rev c7)

// It works fine under the old regime //
// Here's what hdparm -i /dev/hda returns: //

/dev/hda:

Model=ST380011A, FwRev=8.01, SerialNo=5JVQHHJ9
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% } RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4 BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=156301488 IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}

PIO modes:  pio0 pio1 pio2 pio3 pio4
DMA modes:  mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5

AdvancedPM=no WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 2: ATA/ATAPI-1 ATA/ATAPI-2 ATA/ATAPI-3 ATA/ATAPI-4 ATA/ATAPI-5 ATA/ATAPI-6

* signifies the current active mode

// and /dev/hdb: //

/dev/hdb:

Model=PIONEER DVD-RW DVR-108, FwRev=1.10, SerialNo= Config={ Fixed Removeable DTR<=5Mbs DTR>10Mbs nonMagnetic } RawCHS=0/0/0, TrkSize=0, SectSize=0, ECCbytes=0 BuffType=13395, BuffSize=64kB, MaxMultSect=0
(maybe): CurCHS=0/0/0, CurSects=0, LBA=yes, LBAsects=0 IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}

PIO modes:  pio0 pio1 pio2 pio3 pio4
DMA modes:  mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 *udma4

AdvancedPM=no
Drive conforms to: Unspecified: ATA/ATAPI-2 ATA/ATAPI-3 ATA/ATAPI-4 ATA/ATAPI-5

* signifies the current active mode

// Here's what happens on the command line when I modprobe the module and then lsmod. //

frontman ata # modprobe -v pata_ali
insmod /lib/modules/2.6.19-gentoo/kernel/drivers/ata/pata_ali.ko Segmentation fault
frontman ata # lsmod

Module                  Size  Used by
pata_ali                7714  1
snd_seq_midi            6048  0
rtc                     9972  0
snd_ens1371            18752  0
snd_rawmidi            17824  2 snd_seq_midi,snd_ens1371
snd_ac97_codec         90084  1 snd_ens1371
snd_ac97_bus            1856  1 snd_ac97_codec
k8temp                  4352  0

// here's the tail end of dmesg after the modprobe //

BUG: unable to handle kernel NULL pointer dereference at virtual address 00000020
printing eip:
f8ba0823
*pde = 00000000
Oops: 0000 [#1]
PREEMPT
Modules linked in: pata_ali snd_seq_midi rtc snd_ens1371 snd_rawmidi snd_ac97_codec snd_ac97_bus k8temp
CPU:    0
EIP:    0060:[<f8ba0823>]    Not tainted VLI
EFLAGS: 00010246   (2.6.19-gentoo #5)

EIP is at ali_init_one+0x1ba/0x2f7 [pata_ali]
eax: ef47fe1a ebx: 00000000 ecx: f7cb84b0 edx: 00000001
esi: f7cbcc00 edi: f7cb8400 ebp: f6f5f9a0 esp: ef47fe08
ds: 007b es: 007b ss: 0068
Process modprobe (pid: 4770, ti=ef47e000 task=f1a25a70 task.ti=ef47e000)

Stack: 000010b9 00001533 00000079 ef47fe1a c7c11734 f8ba1734 f8ba1700 f7cbcc00
      c024b556 f7cbcc00 f8ba09bc f7cbcc48 f7cbcc48 f8ba1734 c02a9dce 
f7cbcc48
      c17df0c0 000000d0 c036d1de f7cbcc48 ef47fe84 c02a9fa1 f8ba1734 
c02a9fef
Call Trace:
[<c024b556>] pci_device_probe+0x44/0x68
[<c02a9dce>] really_probe+0x3c/0xe4
[<c036d1de>] klist_next+0x57/0x95
[<c02a9fa1>] __driver_attach+0x0/0x81
[<c02a9fef>] __driver_attach+0x4e/0x81
[<c02a93b6>] bus_for_each_dev+0x51/0x78
[<c02a9cd8>] driver_attach+0x26/0x2a
[<c02a9fa1>] __driver_attach+0x0/0x81
[<c02a9739>] bus_add_driver+0x66/0x18d
[<c02aa1f3>] driver_register+0x80/0x8d
[<c024b6ec>] __pci_register_driver+0x63/0x86
[<f8ba3017>] ali_init+0x17/0x1a [pata_ali]
[<c012f670>] sys_init_module+0x1471/0x1628
[<c0102a69>] sysenter_past_esp+0x56/0x79
=======================
Code: 00 c7 04 24 b9 10 00 00 e8 06 b4 6a c7 85 ff 89 c3 74 64 66 81 7f 24 b9 10 75 5c 8d 44 24 12 c7 44 24 08 79 00 00 00 89 44 24 0c <8b> 43 20 89 44 24 04 8b 43 10 89 04 24 e8 b1 63 6a c7 80 7c 24
EIP: [<f8ba0823>] ali_init_one+0x1ba/0x2f7 [pata_ali] SS:ESP 0068:ef47fe08

// Just for yuks I took a look at the pata_ali.c code at // http://kernel.org/git/?p=linux/kernel/git/torvalds/linux-2.6.git;a=blob;h=1d695df5860a3ac44fc77476847d88f50927d7fb;f=drivers/ata/pata_ali.c // // and noticed that starting at line 510 there are a bunch of "static struct ata_port_info info_20" like structure //
// declarations (definitions ?) that seem to reference various revisions of the chip. Mine is a c7 and there's no //
// structure for that one. Could this be the problem?

TIA, Ron
[email protected]

#1 lore raw
Quoted 5 lines · On Thu, 30 Nov 2006 22:14:49 -0800 ron moncreiff <[email protected]> wrote:

// I have tried out the new pata options in the 2.6.19 kernel and had some problems. //
// So here's the skinny. I am using the asrock 939dual - sataII mobo. lspci reports //
// the IDE interface thus: //

As you've no doubt noticed it isn't supposed to oops. Can you send me an lspci -vxx of your system and in the mean time I will go and stare at the code and see what is going on.

Quoted 3 lines

// declarations (definitions ?) that seem to reference various revisions of the chip. Mine is a c7 and there's no //
// structure for that one. Could this be the problem?

C7 is quite new but the info blocks cover ranges of versions not specific versions. It shouldn't be the cause but...

Alan