Skip to contentSkip to conversation

IPMI: Add maintenance mode

PATCH In review Corey Minyard 1 participant 1 message Dec 2, 2006 IPMI

lore
Share & tools
lore
#0 lore raw

PATCH 5/12 IPMI: Add maintenance mode

Some commands and operations on a BMC can cause the BMC to "go away" for a while. This can cause the automatic flag processing and other things of that nature to timeout and generate annoying logs, or possibly cause other bad things to happen when in firmware update mode.

This patch adds detection of those commands (cold reset, warm reset, and any firmware command) and turns off automatic processing for 30 seconds. It also add a manual override either way.

drivers/char/ipmi/ipmi_devintf.c +25 -0
Index: linux-2.6.19-rc6/drivers/char/ipmi/ipmi_devintf.c
===================================================================
@@ -596,6 +596,31 @@ static int ipmi_ioctl(struct inode  *ino
 		rv = 0;
 		break;
 	}
+
+	case IPMICTL_GET_MAINTENANCE_MODE_CMD:
+	{
+		int mode;
+
+		mode = ipmi_get_maintenance_mode(priv->user);
+		if (copy_to_user(arg, &mode, sizeof(mode))) {
+			rv = -EFAULT;
+			break;
+		}
+		rv = 0;
+		break;
+	}
+
+	case IPMICTL_SET_MAINTENANCE_MODE_CMD:
+	{
+		int mode;
+
+		if (copy_from_user(&mode, arg, sizeof(mode))) {
+			rv = -EFAULT;
+			break;
+		}
+		rv = ipmi_set_maintenance_mode(priv->user, mode);
+		break;
+	}
 	}
   
 	return rv;
drivers/char/ipmi/ipmi_msghandler.c +116 -1

165 lines not on this page · raw message

drivers/char/ipmi/ipmi_si_intf.c +9 -0
Index: linux-2.6.19-rc6/drivers/char/ipmi/ipmi_si_intf.c
===================================================================
@@ -949,12 +949,21 @@ static int smi_start_processing(void    
 	return 0;
 }
 
+static void set_maintenance_mode(void *send_info, int enable)
+{
+	struct smi_info   *smi_info = send_info;
+
+	if (!enable)
+		atomic_set(&smi_info->req_events, 0);
+}
+
 static struct ipmi_smi_handlers handlers =
 {
 	.owner                  = THIS_MODULE,
 	.start_processing       = smi_start_processing,
 	.sender			= sender,
 	.request_events		= request_events,
+	.set_maintenance_mode   = set_maintenance_mode,
 	.set_run_to_completion  = set_run_to_completion,
 	.poll			= poll,
 };
include/linux/ipmi.h +45 -0

61 lines not on this page · raw message

include/linux/ipmi_msgdefs.h +5 -0
Index: linux-2.6.19-rc6/include/linux/ipmi_msgdefs.h
===================================================================
@@ -46,6 +46,8 @@
 #define IPMI_NETFN_APP_REQUEST			0x06
 #define IPMI_NETFN_APP_RESPONSE			0x07
 #define IPMI_GET_DEVICE_ID_CMD		0x01
+#define IPMI_COLD_RESET_CMD		0x02
+#define IPMI_WARM_RESET_CMD		0x03
 #define IPMI_CLEAR_MSG_FLAGS_CMD	0x30
 #define IPMI_GET_DEVICE_GUID_CMD	0x08
 #define IPMI_GET_MSG_FLAGS_CMD		0x31
@@ -60,6 +62,9 @@
 #define IPMI_NETFN_STORAGE_RESPONSE		0x0b
 #define IPMI_ADD_SEL_ENTRY_CMD		0x44
 
+#define IPMI_NETFN_FIRMWARE_REQUEST		0x08
+#define IPMI_NETFN_FIRMWARE_RESPONSE		0x09
+
 /* The default slave address */
 #define IPMI_BMC_SLAVE_ADDR	0x20
 
include/linux/ipmi_smi.h +7 -0
Index: linux-2.6.19-rc6/include/linux/ipmi_smi.h
===================================================================
@@ -115,6 +115,13 @@ struct ipmi_smi_handlers
 	   poll for operations during things like crash dumps. */
 	void (*poll)(void *send_info);
 
+	/* Enable/disable firmware maintenance mode.  Note that this
+	   is *not* the modes defined, this is simply an on/off
+	   setting.  The message handler does the mode handling.  Note
+	   that this is called from interupt context, so it cannot
+	   block. */
+	void (*set_maintenance_mode)(void *send_info, int enable);
+
 	/* Tell the handler that we are using it/not using it.  The
 	   message handler get the modules that this handler belongs
 	   to; this function lets the SMI claim any modules that it