Skip to contentSkip to conversation

HDA Intel sound driver fails on Acer notebook

DISCUSSION Chuck Ebbert 4 participants 7 messages Dec 3, 2006 – Feb 19, 2007

lore
Share & tools
lore
#0 lore raw

The HDA Intel sound driver still fails to load on my Acer Aspire 5102 notebook (Turion64 X2, ATI chipset):

Here is the PCI info while running x86_64. I tried i386 and x86_64 and it fails on both:

00:14.2 Audio device: ATI Technologies Inc Unknown device 437b (rev 01)
Subsystem: Acer Incorporated [ALI] Unknown device 009f
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size 08
Interrupt: pin ? routed to IRQ 16
Region 0: Memory at c0000000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
00: 02 10 7b 43 06 00 10 04 01 00 03 04 08 40 00 00
10: 04 00 00 c0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 25 10 9f 00
30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 00 00 00
40: 00 00 02 40 00 00 00 00 00 00 00 00 00 00 00 00
50: 01 60 42 c8 00 00 00 00 00 00 00 00 00 00 00 00
60: 05 00 80 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

On i386 I get this after doing
insmod snd-hda-codec.ko ; insmod snd-hda-intel.ko

Dec  1 17:38:29 ac kernel: ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 18
Dec  1 17:38:29 ac kernel: codec_mask = 0xb
Dec  1 17:38:30 ac kernel: hda_codec: PCI 1025:9f, codec config 5 is selected
Dec  1 17:38:31 ac kernel: hda_intel: azx_get_response timeout, switching to polling mode...
Dec  1 17:38:32 ac kernel: hda_intel: azx_get_response timeout, switching to single_cmd mode...
Dec  1 17:38:32 ac kernel: hda-intel: get_response timeout: IRS=0x0
Dec  1 17:38:36 ac last message repeated 24618 times
Dec  1 17:38:36 ac kernel: hda_codec: invalid dep_range_val 0:7fff
Dec  1 17:38:36 ac kernel: hda_codec: invalid dep_range_val 0:7fff
Dec  1 17:38:36 ac kernel: hda-intel: get_response timeout: IRS=0x0
Dec  1 17:38:36 ac kernel: hda_codec: invalid dep_range_val 0:7fff
Dec  1 17:38:36 ac kernel: hda_codec: invalid dep_range_val 0:7fff
Dec  1 17:38:36 ac kernel: hda-intel: get_response timeout: IRS=0x0

The last three lines repeat many thousands of times, followed by:

Dec  1 17:38:39 ac kernel: hda_generic: no proper input path found
Dec  1 17:38:39 ac kernel: hda_generic: no proper output path found
Dec  1 17:38:39 ac kernel: hda_generic: no PCM found

Looking at /proc/interrupts, I see exactly 110 interrupts were processed by the driver while all this was happening:

18: 0 110 IO-APIC-fasteoi HDA Intel

On x86_64 I forgot to enable verbose messages, so there's less information but it fails the same way.

Signature · 8 lines
Chuck
"Even supernovas have their duller moments."

-------------------------------------------------------------------------
Take Surveys. Earn Cash. Influence the Future of IT
Join SourceForge.net's Techsay panel and you'll get the chance to share your
opinions on IT & business topics through brief surveys - and earn cash
http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV
#1 lore raw

FWIW, I'm having problems with this same laptop as well (i386). Same number of interrupts in /proc/interrupts. Interestingly, OSS output works (mostly), but all of the ALSA commands fail:

tony@maus:~$ amixer -d scontrols
amixer: Mixer default load error: Invalid argument
tony@maus:~$ aplay ./test.wav
ALSA lib confmisc.c:1105:(snd_func_refer) Unable to find definition
'defaults.pcm.dmix_format'
ALSA lib conf.c:3500:(_snd_config_evaluate) function snd_func_refer
returned error: No such file or directory
ALSA lib conf.c:3957:(snd_config_expand) Args evaluate error: No such file
or directory
ALSA lib pcm.c:2143:(snd_pcm_open_noupdate) Unknown PCM dmix:0
aplay: main:550: audio open error: No such file or directory

However, this is running 1.0.13. I have yet to test with the 1.0.14rc1 pre-packages that were posted earlier today.

Quoted 58 lines · Chuck Ebbert

The HDA Intel sound driver still fails to load on my Acer Aspire 5102 notebook (Turion64 X2, ATI chipset):

Here is the PCI info while running x86_64. I tried i386 and x86_64 and it fails on both:

00:14.2 Audio device: ATI Technologies Inc Unknown device 437b (rev 01)
Subsystem: Acer Incorporated [ALI] Unknown device 009f
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size 08
Interrupt: pin ? routed to IRQ 16
Region 0: Memory at c0000000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
00: 02 10 7b 43 06 00 10 04 01 00 03 04 08 40 00 00
10: 04 00 00 c0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 25 10 9f 00
30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 00 00 00
40: 00 00 02 40 00 00 00 00 00 00 00 00 00 00 00 00
50: 01 60 42 c8 00 00 00 00 00 00 00 00 00 00 00 00
60: 05 00 80 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

On i386 I get this after doing
insmod snd-hda-codec.ko ; insmod snd-hda-intel.ko

Dec  1 17:38:29 ac kernel: ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 18
Dec  1 17:38:29 ac kernel: codec_mask = 0xb
Dec  1 17:38:30 ac kernel: hda_codec: PCI 1025:9f, codec config 5 is selected
Dec  1 17:38:31 ac kernel: hda_intel: azx_get_response timeout, switching to polling mode...
Dec  1 17:38:32 ac kernel: hda_intel: azx_get_response timeout, switching to single_cmd mode...
Dec  1 17:38:32 ac kernel: hda-intel: get_response timeout: IRS=0x0
Dec  1 17:38:36 ac last message repeated 24618 times
Dec  1 17:38:36 ac kernel: hda_codec: invalid dep_range_val 0:7fff
Dec  1 17:38:36 ac kernel: hda_codec: invalid dep_range_val 0:7fff
Dec  1 17:38:36 ac kernel: hda-intel: get_response timeout: IRS=0x0
Dec  1 17:38:36 ac kernel: hda_codec: invalid dep_range_val 0:7fff
Dec  1 17:38:36 ac kernel: hda_codec: invalid dep_range_val 0:7fff
Dec  1 17:38:36 ac kernel: hda-intel: get_response timeout: IRS=0x0

The last three lines repeat many thousands of times, followed by:

Dec  1 17:38:39 ac kernel: hda_generic: no proper input path found
Dec  1 17:38:39 ac kernel: hda_generic: no proper output path found
Dec  1 17:38:39 ac kernel: hda_generic: no PCM found
Quoted 8 lines

Looking at /proc/interrupts, I see exactly 110 interrupts were processed by the driver while all this was happening:

18: 0 110 IO-APIC-fasteoi HDA Intel

On x86_64 I forgot to enable verbose messages, so there's less information but it fails the same way.

-------------------------------------------------------------------------
Take Surveys. Earn Cash. Influence the Future of IT
Join SourceForge.net's Techsay panel and you'll get the chance to share your opinions on IT & business topics through brief surveys - and earn cash
http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV

#2 lore raw

Re: HDA Intel sound driver fails on Acer notebook - UPDATE, PROGRESS!

There is some definite progress with the recent driver snapshots (since 1.0.14rc2). Using alsa-driver-hg20070217.tar.bz2, amixer and gnome-alsamixer both work, and after setting up xmms to use the software mixer, it's working as well.

This is a big step forward - it's the first time I've been able to boot this laptop and reliably have sound under Linux. Up until now, it's been hit-or-miss whether OSS emulation would emit sound, perhaps at a very low level, etc., and none of the alsa tools worked at all.

To keep those interested from having to browse the thread, this is regarding an Acer Aspire 5102 WMLi, with a Realtek ALC883, using the hda-intel driver.
I'm using the stock Debian kernel that's currently in etch (2.6.18-3).

Many thanks to the ALSA developers!
tony

Quoted 17 lines · tony mancill

FWIW, I'm having problems with this same laptop as well (i386). Same number of interrupts in /proc/interrupts. Interestingly, OSS output works (mostly), but all of the ALSA commands fail:

tony@maus:~$ amixer -d scontrols
amixer: Mixer default load error: Invalid argument
tony@maus:~$ aplay ./test.wav
ALSA lib confmisc.c:1105:(snd_func_refer) Unable to find definition
'defaults.pcm.dmix_format'
ALSA lib conf.c:3500:(_snd_config_evaluate) function snd_func_refer
returned error: No such file or directory
ALSA lib conf.c:3957:(snd_config_expand) Args evaluate error: No such file
or directory
ALSA lib pcm.c:2143:(snd_pcm_open_noupdate) Unknown PCM dmix:0
aplay: main:550: audio open error: No such file or directory
Quoted 73 lines

However, this is running 1.0.13. I have yet to test with the 1.0.14rc1 pre-packages that were posted earlier today.

Quoted 66 lines · Chuck Ebbert

The HDA Intel sound driver still fails to load on my Acer Aspire 5102 notebook (Turion64 X2, ATI chipset):

Here is the PCI info while running x86_64. I tried i386 and x86_64 and it fails on both:

00:14.2 Audio device: ATI Technologies Inc Unknown device 437b (rev 01)
Subsystem: Acer Incorporated [ALI] Unknown device 009f
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size 08
Interrupt: pin ? routed to IRQ 16
Region 0: Memory at c0000000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
00: 02 10 7b 43 06 00 10 04 01 00 03 04 08 40 00 00
10: 04 00 00 c0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 25 10 9f 00
30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 00 00 00
40: 00 00 02 40 00 00 00 00 00 00 00 00 00 00 00 00
50: 01 60 42 c8 00 00 00 00 00 00 00 00 00 00 00 00
60: 05 00 80 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

On i386 I get this after doing
insmod snd-hda-codec.ko ; insmod snd-hda-intel.ko

Dec  1 17:38:29 ac kernel: ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 18
Dec  1 17:38:29 ac kernel: codec_mask = 0xb
Dec  1 17:38:30 ac kernel: hda_codec: PCI 1025:9f, codec config 5 is selected
Dec  1 17:38:31 ac kernel: hda_intel: azx_get_response timeout, switching to polling mode...
Dec  1 17:38:32 ac kernel: hda_intel: azx_get_response timeout, switching to single_cmd mode...
Dec  1 17:38:32 ac kernel: hda-intel: get_response timeout: IRS=0x0
Dec  1 17:38:36 ac last message repeated 24618 times
Dec  1 17:38:36 ac kernel: hda_codec: invalid dep_range_val 0:7fff
Dec  1 17:38:36 ac kernel: hda_codec: invalid dep_range_val 0:7fff
Dec  1 17:38:36 ac kernel: hda-intel: get_response timeout: IRS=0x0
Dec  1 17:38:36 ac kernel: hda_codec: invalid dep_range_val 0:7fff
Dec  1 17:38:36 ac kernel: hda_codec: invalid dep_range_val 0:7fff
Dec  1 17:38:36 ac kernel: hda-intel: get_response timeout: IRS=0x0

The last three lines repeat many thousands of times, followed by:

Dec  1 17:38:39 ac kernel: hda_generic: no proper input path found
Dec  1 17:38:39 ac kernel: hda_generic: no proper output path found
Dec  1 17:38:39 ac kernel: hda_generic: no PCM found

Looking at /proc/interrupts, I see exactly 110 interrupts were processed by the driver while all this was happening:

18: 0 110 IO-APIC-fasteoi HDA Intel

On x86_64 I forgot to enable verbose messages, so there's less information but it fails the same way.

-------------------------------------------------------------------------
Take Surveys. Earn Cash. Influence the Future of IT
Join SourceForge.net's Techsay panel and you'll get the chance to share your opinions on IT & business topics through brief surveys-and earn cash
http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV

#3 lore raw
In reply to Chuck Ebbert

Hi,

sorry for the late reply since I've been on vacation.

At Sun, 3 Dec 2006 02:30:34 -0500,

Quoted 36 lines · Chuck Ebbert

The HDA Intel sound driver still fails to load on my Acer Aspire 5102 notebook (Turion64 X2, ATI chipset):

Here is the PCI info while running x86_64. I tried i386 and x86_64 and it fails on both:

00:14.2 Audio device: ATI Technologies Inc Unknown device 437b (rev 01)
Subsystem: Acer Incorporated [ALI] Unknown device 009f
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size 08
Interrupt: pin ? routed to IRQ 16
Region 0: Memory at c0000000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
00: 02 10 7b 43 06 00 10 04 01 00 03 04 08 40 00 00
10: 04 00 00 c0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 25 10 9f 00
30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 00 00 00
40: 00 00 02 40 00 00 00 00 00 00 00 00 00 00 00 00
50: 01 60 42 c8 00 00 00 00 00 00 00 00 00 00 00 00
60: 05 00 80 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Quoted 8 lines

On i386 I get this after doing
insmod snd-hda-codec.ko ; insmod snd-hda-intel.ko

Dec  1 17:38:29 ac kernel: ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 18
Dec  1 17:38:29 ac kernel: codec_mask = 0xb
Dec  1 17:38:30 ac kernel: hda_codec: PCI 1025:9f, codec config 5 is selected
Dec  1 17:38:31 ac kernel: hda_intel: azx_get_response timeout, switching to polling mode...
Dec  1 17:38:32 ac kernel: hda_intel: azx_get_response timeout, switching to single_cmd mode...

These messages are scary. It means that the communication between the controller chip and the codec chip doesn't work, usually incorrect IRQ handling, and often due to broken BIOS or ACPI support. Any change if you pass pci=noacpi or acpi=off boot option?

Anyway, you can try alsa-git patch in mm tree. It's a better support code for Acer laptops, and this might work slightly differently.

Takashi

-------------------------------------------------------------------------
Take Surveys. Earn Cash. Influence the Future of IT
Join SourceForge.net's Techsay panel and you'll get the chance to share your opinions on IT & business topics through brief surveys - and earn cash
http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV

#4 lore raw

FWIW, using pci=noacpi seems to break the USB controller on this laptop. I get "device not accepting address xx, error -110.

In addition, neither the onboard nor the wireless NIC work anymore with this option. For the onboard, you see that the link is up, but then get "NETDEV WATCHDOG: eth0: transmit timed out."

acpi=off is worse - the boot hangs trying to load acpi/thermal.ko.

I've tested with both 1.0.13 and and 1.0.14rc1. I don't get exactly the same kernel logging (I'm using a Debian 2.6.18 kernel), but kern.log contains:

Dec 19 17:39:43 maus kernel: : hda_codec: invalid dep_range_val 0:7fff
Dec 19 17:39:43 maus kernel: ALSA /home/tony/alsa-driver-1.0.14rc1/pci/hda/hda_codec.c:216: hda_codec: invalid dep_range_val 0:7fff
Dec 19 17:39:43 maus last message repeated 279 times
Dec 19 17:39:43 maus kernel: hda_codec: num_steps = 0 for NID=0xd
Dec 19 17:39:43 maus kernel: hda_codec: num_steps = 0 for NID=0x9
Dec 19 17:39:43 maus kernel: hda_codec: num_steps = 0 for NID=0xd
Dec 19 17:39:43 maus last message repeated 20 times
Dec 19 17:39:43 maus kernel: hda_codec: num_steps = 0 for NID=0x9

Thanks in advance for any assistance. I hope you enjoyed your vacation.

Thanks,
tony

Quoted 55 lines · Takashi Iwai

Hi,

sorry for the late reply since I've been on vacation.

At Sun, 3 Dec 2006 02:30:34 -0500,

Quoted 35 lines · Chuck Ebbert

The HDA Intel sound driver still fails to load on my Acer Aspire 5102 notebook (Turion64 X2, ATI chipset):

Here is the PCI info while running x86_64. I tried i386 and x86_64 and it fails on both:

00:14.2 Audio device: ATI Technologies Inc Unknown device 437b (rev 01)
Subsystem: Acer Incorporated [ALI] Unknown device 009f
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size 08
Interrupt: pin ? routed to IRQ 16
Region 0: Memory at c0000000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
00: 02 10 7b 43 06 00 10 04 01 00 03 04 08 40 00 00
10: 04 00 00 c0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 25 10 9f 00
30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 00 00 00
40: 00 00 02 40 00 00 00 00 00 00 00 00 00 00 00 00
50: 01 60 42 c8 00 00 00 00 00 00 00 00 00 00 00 00
60: 05 00 80 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Quoted 8 lines

On i386 I get this after doing
insmod snd-hda-codec.ko ; insmod snd-hda-intel.ko

Dec  1 17:38:29 ac kernel: ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 18
Dec  1 17:38:29 ac kernel: codec_mask = 0xb
Dec  1 17:38:30 ac kernel: hda_codec: PCI 1025:9f, codec config 5 is selected
Dec  1 17:38:31 ac kernel: hda_intel: azx_get_response timeout, switching to polling mode...
Dec  1 17:38:32 ac kernel: hda_intel: azx_get_response timeout, switching to single_cmd mode...

These messages are scary. It means that the communication between the controller chip and the codec chip doesn't work, usually incorrect IRQ handling, and often due to broken BIOS or ACPI support. Any change if you pass pci=noacpi or acpi=off boot option?

Quoted 5 lines

Anyway, you can try alsa-git patch in mm tree. It's a better support code for Acer laptops, and this might work slightly differently.

Takashi

-------------------------------------------------------------------------
Take Surveys. Earn Cash. Influence the Future of IT
Join SourceForge.net's Techsay panel and you'll get the chance to share your opinions on IT & business topics through brief surveys - and earn cash
http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV

#5 lore raw
Quoted 2 lines · tony mancill

FWIW, using pci=noacpi seems to break the USB controller on this laptop. I get "device not accepting address xx, error -110.

Strange. I'm using an Acer Aspire 1640Z and the sound works perfectly. Of course Kubuntu was the only distro I could find that did OOB, but that's besides the point. In a quick look through /etc on my laptop I wasn't able to see how they do this. But after doing a quick check on Google the reports vary from this being a patched bug in ALSA to being easily solved by ensuring that the needed sound modules are loaded in the proper order.

An alternate solution to this is to load the snd-hda-intel module with the parameter "model=laptop"

Quoted 7 lines

In addition, neither the onboard nor the wireless NIC work anymore with this option. For the onboard, you see that the link is up, but then get "NETDEV WATCHDOG: eth0: transmit timed out."

acpi=off is worse - the boot hangs trying to load acpi/thermal.ko.

From personal experience I can say that ACPI is needed for Acer notebooks with

the centrino chipset to function properly.

Quoted 3 lines

I've tested with both 1.0.13 and and 1.0.14rc1. I don't get exactly the same kernel logging (I'm using a Debian 2.6.18 kernel), but kern.log contains:

I had the same problem when I tried Debian on this laptop. I don't recommend it for laptops, since there are several common pieces of hardware found on laptops that need firmware not shipped by Debian. This includes the ipw2200 firmware - which most Acer laptops need, because they ship with that wireless card.

Quoted 88 lines
Dec 19 17:39:43 maus kernel: : hda_codec: invalid dep_range_val 0:7fff
Dec 19 17:39:43 maus kernel: ALSA
/home/tony/alsa-driver-1.0.14rc1/pci/hda/hda_codec.c:216: hda_codec:
invalid dep_range_val 0:7fff Dec 19 17:39:43 maus last message repeated 279
times
Dec 19 17:39:43 maus kernel: hda_codec: num_steps = 0 for NID=0xd
Dec 19 17:39:43 maus kernel: hda_codec: num_steps = 0 for NID=0x9
Dec 19 17:39:43 maus kernel: hda_codec: num_steps = 0 for NID=0xd
Dec 19 17:39:43 maus last message repeated 20 times
Dec 19 17:39:43 maus kernel: hda_codec: num_steps = 0 for NID=0x9

Thanks in advance for any assistance. I hope you enjoyed your vacation.

Thanks,
tony

Quoted 59 lines · Takashi Iwai

Hi,

sorry for the late reply since I've been on vacation.

At Sun, 3 Dec 2006 02:30:34 -0500,

Quoted 40 lines · Chuck Ebbert

The HDA Intel sound driver still fails to load on my Acer Aspire 5102 notebook (Turion64 X2, ATI chipset):

Here is the PCI info while running x86_64. I tried i386 and x86_64 and it fails on both:

00:14.2 Audio device: ATI Technologies Inc Unknown device 437b (rev 01)
Subsystem: Acer Incorporated [ALI] Unknown device 009f
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency:
64, Cache Line Size 08
Interrupt: pin ? routed to IRQ 16
Region 0: Memory at c0000000 (64-bit, non-prefetchable)
[size=16K] Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA
PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: 64bit+
Queue=0/0 Enable- Address: 0000000000000000 Data: 0000
00: 02 10 7b 43 06 00 10 04 01 00 03 04 08 40 00 00
10: 04 00 00 c0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 25 10 9f 00
30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 00 00 00
40: 00 00 02 40 00 00 00 00 00 00 00 00 00 00 00 00
50: 01 60 42 c8 00 00 00 00 00 00 00 00 00 00 00 00
60: 05 00 80 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

On i386 I get this after doing
insmod snd-hda-codec.ko ; insmod snd-hda-intel.ko

Quoted 6 lines
Dec  1 17:38:29 ac kernel: ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16
(level, low) -> IRQ 18 Dec  1 17:38:29 ac kernel: codec_mask = 0xb
Dec  1 17:38:30 ac kernel: hda_codec: PCI 1025:9f, codec config 5 is

selected Dec 1 17:38:31 ac kernel: hda_intel: azx_get_response timeout, switching to polling mode... Dec 1 17:38:32 ac kernel: hda_intel:
azx_get_response timeout, switching to single_cmd mode...

These messages are scary. It means that the communication between the controller chip and the codec chip doesn't work, usually incorrect IRQ handling, and often due to broken BIOS or ACPI support. Any change if you pass pci=noacpi or acpi=off boot option?

Quoted 5 lines

Anyway, you can try alsa-git patch in mm tree. It's a better support code for Acer laptops, and this might work slightly differently.

Takashi

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

#6 lore raw
In reply to tony mancill
Quoted 2 lines · tony mancill

FWIW, using pci=noacpi seems to break the USB controller on this laptop. I get "device not accepting address xx, error -110.

Strange. I'm using an Acer Aspire 1640Z and the sound works perfectly. Of course Kubuntu was the only distro I could find that did OOB, but that's besides the point. In a quick look through /etc on my laptop I wasn't able to see how they do this. But after doing a quick check on Google the reports vary from this being a patched bug in ALSA to being easily solved by ensuring that the needed sound modules are loaded in the proper order.

An alternate solution to this is to load the snd-hda-intel module with the parameter "model=laptop"

Quoted 7 lines

In addition, neither the onboard nor the wireless NIC work anymore with this option. For the onboard, you see that the link is up, but then get "NETDEV WATCHDOG: eth0: transmit timed out."

acpi=off is worse - the boot hangs trying to load acpi/thermal.ko.

From personal experience I can say that ACPI is needed for Acer notebooks with

the centrino chipset to function properly.

Quoted 3 lines

I've tested with both 1.0.13 and and 1.0.14rc1. I don't get exactly the same kernel logging (I'm using a Debian 2.6.18 kernel), but kern.log contains:

I had the same problem when I tried Debian on this laptop. I don't recommend it for laptops, since there are several common pieces of hardware found on laptops that need firmware not shipped by Debian. This includes the ipw2200 firmware - which most Acer laptops need, because they ship with that wireless card.

Quoted 81 lines
Dec 19 17:39:43 maus kernel: : hda_codec: invalid dep_range_val 0:7fff
Dec 19 17:39:43 maus kernel: ALSA
/home/tony/alsa-driver-1.0.14rc1/pci/hda/hda_codec.c:216: hda_codec:
invalid dep_range_val 0:7fff Dec 19 17:39:43 maus last message repeated 279
times
Dec 19 17:39:43 maus kernel: hda_codec: num_steps = 0 for NID=0xd
Dec 19 17:39:43 maus kernel: hda_codec: num_steps = 0 for NID=0x9
Dec 19 17:39:43 maus kernel: hda_codec: num_steps = 0 for NID=0xd
Dec 19 17:39:43 maus last message repeated 20 times
Dec 19 17:39:43 maus kernel: hda_codec: num_steps = 0 for NID=0x9

Thanks in advance for any assistance. I hope you enjoyed your vacation.

Thanks,
tony

Quoted 63 lines · Takashi Iwai

Hi,

sorry for the late reply since I've been on vacation.

At Sun, 3 Dec 2006 02:30:34 -0500,

Quoted 40 lines · Chuck Ebbert

The HDA Intel sound driver still fails to load on my Acer Aspire 5102 notebook (Turion64 X2, ATI chipset):

Here is the PCI info while running x86_64. I tried i386 and x86_64 and it fails on both:

00:14.2 Audio device: ATI Technologies Inc Unknown device 437b (rev 01)
Subsystem: Acer Incorporated [ALI] Unknown device 009f
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency:
64, Cache Line Size 08
Interrupt: pin ? routed to IRQ 16
Region 0: Memory at c0000000 (64-bit, non-prefetchable)
[size=16K] Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA
PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: 64bit+
Queue=0/0 Enable- Address: 0000000000000000 Data: 0000
00: 02 10 7b 43 06 00 10 04 01 00 03 04 08 40 00 00
10: 04 00 00 c0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 25 10 9f 00
30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 00 00 00
40: 00 00 02 40 00 00 00 00 00 00 00 00 00 00 00 00
50: 01 60 42 c8 00 00 00 00 00 00 00 00 00 00 00 00
60: 05 00 80 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

On i386 I get this after doing
insmod snd-hda-codec.ko ; insmod snd-hda-intel.ko

Quoted 6 lines
Dec  1 17:38:29 ac kernel: ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16
(level, low) -> IRQ 18 Dec  1 17:38:29 ac kernel: codec_mask = 0xb
Dec  1 17:38:30 ac kernel: hda_codec: PCI 1025:9f, codec config 5 is

selected Dec 1 17:38:31 ac kernel: hda_intel: azx_get_response timeout, switching to polling mode... Dec 1 17:38:32 ac kernel: hda_intel:
azx_get_response timeout, switching to single_cmd mode...

These messages are scary. It means that the communication between the controller chip and the codec chip doesn't work, usually incorrect IRQ handling, and often due to broken BIOS or ACPI support. Any change if you pass pci=noacpi or acpi=off boot option?

Anyway, you can try alsa-git patch in mm tree. It's a better support code for Acer laptops, and this might work slightly differently.

Quoted 7 lines
Quoted 1 line

Takashi

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

-------------------------------------------------------------------------
Take Surveys. Earn Cash. Influence the Future of IT
Join SourceForge.net's Techsay panel and you'll get the chance to share your opinions on IT & business topics through brief surveys - and earn cash
http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV