Skip to contentSkip to conversation

driver for SMSC SCH311x

PATCH In review Marcin Dawidowicz 6 participants 9 messages Jul 24, 2006 – Jun 21, 2007 Hardware monitoring

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 driver for SMSC SCH311x

Hello,

Below you find my SMSC SCH311x chips driver. Currently, it supports voltage, temperature inputs and alarms. There is not implemented support for fans and pwm control (I couldn't test it on my hardware).

Thanks for your feedback,
Marcin

Signed-off-by Marcin Dawidowicz <Marcin.Dawidowicz at kontron.pl>
drivers/hwmon/Kconfig +11 -0
diff -uprN -X ./linux-2.6.18-rc2-vanilla/Documentation/dontdiff linux-2.6.18-rc2-vanilla/drivers/hwmon/Kconfig linux-2.6.18-rc2-sch311x/drivers/hwmon/Kconfig
@@ -396,6 +396,17 @@ config SENSORS_SMSC47B397
 	  This driver can also be built as a module.  If so, the module
 	  will be called smsc47b397.
 
+config SENSORS_SCH311X
+	tristate "SMSC SCH311x family"
+	depends on HWMON && I2C && EXPERIMENTAL
+	select I2C_ISA
+	help
+	  If you say yes here you get support for the SMSC SCH311x family
+	  sensor chip.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called sch311x.
+
 config SENSORS_VIA686A
 	tristate "VIA686A"
 	depends on HWMON && I2C && PCI
drivers/hwmon/Makefile +1 -0
diff -uprN -X ./linux-2.6.18-rc2-vanilla/Documentation/dontdiff linux-2.6.18-rc2-vanilla/drivers/hwmon/Makefile linux-2.6.18-rc2-sch311x/drivers/hwmon/Makefile
@@ -44,6 +44,7 @@ obj-$(CONFIG_SENSORS_SIS5595)	+= sis5595
 obj-$(CONFIG_SENSORS_SMSC47B397)+= smsc47b397.o
 obj-$(CONFIG_SENSORS_SMSC47M1)	+= smsc47m1.o
 obj-$(CONFIG_SENSORS_SMSC47M192)+= smsc47m192.o
+obj-$(CONFIG_SENSORS_SCH311X)	+= sch311x.o
 obj-$(CONFIG_SENSORS_VIA686A)	+= via686a.o
 obj-$(CONFIG_SENSORS_VT8231)	+= vt8231.o
 obj-$(CONFIG_SENSORS_W83627EHF)	+= w83627ehf.o
drivers/hwmon/sch311x.c +629 -0

629 lines not on this page · raw message

#1 lore raw

PATCH 1/1 driver for SMSC SCH311x

I have installed your patch for the SCH311x on a Kontron 6012 processor board using Redhat linux 2.6.18. After doing a modprobe I now get:

sch311x-isa-0a70
Adapter: ISA adapter

but no further information. Is there something I am missing ?

Your help would be greatly appreciated.

Alan

#2 lore raw

PATCH 1/1 driver for SMSC SCH311x

In reply to Marcin Dawidowicz

Hello Alan,

Sorry for the delay.

Quoted 8 lines · Alan Pettitt

I have installed your patch for the SCH311x on a Kontron 6012 processor board using Redhat linux 2.6.18. After doing a modprobe I now get:

sch311x-isa-0a70
Adapter: ISA adapter

but no further information. Is there something I am missing ?

Yes you are missing userspace support (the generic support is not yet ready). Maybe Marcin will have something? I'm ccing him.

You may access the chip through sysfs interface /sys/class/hwmon*/device/...

Rudolf

#3 lore raw

PATCH 1/1 driver for SMSC SCH311x

In reply to Marcin Dawidowicz

Hello Rudolf and Alan,

Here is my patch for SVN lm-sensors repository to add SMSC SCH311x support for user space from some time ago. I think, there won't be a big problem to apply it to current repository state.

Best regards,
Marcin

Dnia pi?tek 24 listopad 2006 13:31, Rudolf Marek napisa?:

Quoted 26 lines

Hello Alan,

Sorry for the delay.

Quoted 8 lines · Alan Pettitt

I have installed your patch for the SCH311x on a Kontron 6012 processor board using Redhat linux 2.6.18. After doing a modprobe I now get:

sch311x-isa-0a70
Adapter: ISA adapter

but no further information. Is there something I am missing ?

Yes you are missing userspace support (the generic support is not yet ready). Maybe Marcin will have something? I'm ccing him.

You may access the chip through sysfs interface
/sys/class/hwmon*/device/...

Rudolf

_______________________________________________
lm-sensors mailing list
lm-sensors at lm-sensors.org
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors

Signature · 28 lines
Best regards / Mi?ego dnia

Marcin Dawidowicz
 

------------------------------------------------------------------

Kontron East Europe sp. z o.o.
Nowy adres / New address

  03-821 Warszawa Poland
  ul. ?upnicza 17

Tel.:        +48 22  389 84 82

E-MAIL   :  <mailto:marcin.dawidowicz at kontron.pl>
mailto:marcin.dawidowicz at kontron.pl

 "we create digital brains for a more intelligent world"

------------------------------------------------------------------
-------------- next part --------------
A non-text attachment was scrubbed...
Name: sch311x-lm-sensors_SVN.patch
Type: text/x-diff
Size: 13278 bytes
Desc: not available
Url : http://lists.lm-sensors.org/pipermail/lm-sensors/attachments/20061124/084d3622/attachment.bin 
#4 lore raw

PATCH 1/1 driver for SMSC SCH311x

In reply to Marcin Dawidowicz

Marcin,

Thanks very much for that. I applied the patch to the lm_sensors 2.10.1 release and that appears to give me the information I was after.

There were a few small patching errors due to the inclusion of an additional "k8temp" sensor compared to your version, but I manually inserted the additional new lines for the sch311x.

Best Regards

Ala

Quoted 70 lines · Alan Pettitt

-----Original Message-----
From: Marcin Dawidowicz [mailto:marcin.dawidowicz at kontron.pl]
Sent: 24 November 2006 18:19
To: Rudolf Marek
Cc: Alan Pettitt; lm-sensors at lm-sensors.org
Subject: Re: [lm-sensors] [PATCH] driver for SMSC SCH311x

Hello Rudolf and Alan,

Here is my patch for SVN lm-sensors repository to add SMSC SCH311x support for
user space from some time ago. I think, there won't be a big problem to apply
it to current repository state.

Best regards,
Marcin

Dnia pi?tek 24 listopad 2006 13:31, Rudolf Marek napisa?:

Quoted 20 lines

Hello Alan,

Sorry for the delay.

Quoted 8 lines · Alan Pettitt

I have installed your patch for the SCH311x on a Kontron 6012 processor board using Redhat linux 2.6.18. After doing a modprobe I now get:

sch311x-isa-0a70
Adapter: ISA adapter

but no further information. Is there something I am missing ?

Yes you are missing userspace support (the generic support is not yet ready). Maybe Marcin will have something? I'm ccing him.

You may access the chip through sysfs interface
/sys/class/hwmon*/device/...

Quoted 6 lines

Rudolf

_______________________________________________
lm-sensors mailing list
lm-sensors at lm-sensors.org
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors

--
Best regards / Mi?ego dnia

Marcin Dawidowicz

------------------------------------------------------------------

Kontron East Europe sp. z o.o.
Nowy adres / New address

03-821 Warszawa Poland
ul. ?upnicza 17

Tel.: +48 22 389 84 82

E-MAIL : <mailto:marcin.dawidowicz at kontron.pl>
mailto:marcin.dawidowicz at kontron.pl

"we create digital brains for a more intelligent world"

------------------------------------------------------------------

#5 lore raw

PATCH 1/1 driver for SMSC SCH311x

In reply to Marcin Dawidowicz

Hi Marcin,

Quoted 3 lines · Marcin Dawidowicz

Here is my patch for SVN lm-sensors repository to add SMSC SCH311x support for user space from some time ago. I think, there won't be a big problem to apply it to current repository state.

Maybe we can merge the user-space support already, even if I don't have the time to review the driver itself. In particular the detection would be nice to have. Here's my review:

lm-sensors_SVN_modif/lib/chips.c static sensors_chip_feature abituguru_fe · line 5845

Quoted 10 lines

diff -uprN -X dontdiff_my ./lm-sensors_SVN/lib/chips.c ./lm-sensors_SVN_modif/lib/chips.c

lm-sensors_SVN_modif/lib/chips.c renamed from lm-sensors_SVN/lib/chips.c +3 -0
@@ -5840,6 +5840,127 @@ static sensors_chip_feature abituguru_fe
 	{ 0 }
 };
 
+static sensors_chip_feature sch311x_features[] > +  {
+    { SENSORS_SCH311X_IN(0), "2.5V", NOMAP, NOMAP,
+                        R, NOSYSCTL, VALUE(4), 2, "in0_input", 3 },

Please use standard feature names ("in0", "in1", "in0_max", etc.) It is way less confusing if the standard wiring isn't used on a given motherboard (which happens all the time.) Another benefit is that you won't have to explicitly list the Linux 2.6 file names and magnitudes, libsensors will guess them for you.

Quoted 47 lines
lm-sensors_SVN_modif/lib/chips.c renamed from lm-sensors_SVN/lib/chips.c +47 -0
+    { SENSORS_SCH311X_IN(1), "Vccp", NOMAP, NOMAP,
+                        R, NOSYSCTL, VALUE(4), 2, "in1_input", 3 },
+    { SENSORS_SCH311X_IN(2), "VCC", NOMAP, NOMAP,
+                        R, NOSYSCTL, VALUE(4), 2, "in2_input", 3 },
+    { SENSORS_SCH311X_IN(3), "5V", NOMAP, NOMAP,
+                        R, NOSYSCTL, VALUE(4), 2, "in3_input", 3 },
+    { SENSORS_SCH311X_IN(4), "12V", NOMAP, NOMAP,
+                        R, NOSYSCTL, VALUE(4), 2, "in4_input", 3 },
+    { SENSORS_SCH311X_IN(5), "VRT", NOMAP, NOMAP,
+                        R, NOSYSCTL, VALUE(4), 2, "in5_input", 3 },
+    { SENSORS_SCH311X_IN(6), "Vbat", NOMAP, NOMAP,
+                        R, NOSYSCTL, VALUE(4), 2, "in6_input", 3 },
+    { SENSORS_SCH311X_IN_MIN(0), "2.5V_min", SENSORS_SCH311X_IN(0),
+                        SENSORS_SCH311X_IN(0), RW,
+                        NOSYSCTL, VALUE(1), 2, "in0_min", 3 },
+    { SENSORS_SCH311X_IN_MIN(1), "Vccp_min", SENSORS_SCH311X_IN(1),
+                        SENSORS_SCH311X_IN(1), RW,
+                        NOSYSCTL, VALUE(1), 2, "in1_min", 3 },
+    { SENSORS_SCH311X_IN_MIN(2), "VCC_min", SENSORS_SCH311X_IN(2),
+                        SENSORS_SCH311X_IN(2), RW,
+                        NOSYSCTL, VALUE(1), 2, "in2_min", 3 },
+    { SENSORS_SCH311X_IN_MIN(3), "5V_min", SENSORS_SCH311X_IN(3),
+                        SENSORS_SCH311X_IN(3), RW,
+                        NOSYSCTL, VALUE(1), 2, "in3_min", 3 },
+    { SENSORS_SCH311X_IN_MIN(4), "12V_min", SENSORS_SCH311X_IN(4),
+                        SENSORS_SCH311X_IN(4), RW,
+                        NOSYSCTL, VALUE(1), 2, "in4_min", 3 },
+    { SENSORS_SCH311X_IN_MIN(5), "VRT_min", SENSORS_SCH311X_IN(5),
+                        SENSORS_SCH311X_IN(5), RW,
+                        NOSYSCTL, VALUE(1), 2, "in5_min", 3 },
+    { SENSORS_SCH311X_IN_MIN(6), "Vbat_min", SENSORS_SCH311X_IN(6),
+                        SENSORS_SCH311X_IN(6), RW,
+                        NOSYSCTL, VALUE(1), 2, "in6_min", 3 },
+    { SENSORS_SCH311X_IN_MAX(0), "2.5V_max", SENSORS_SCH311X_IN(0),
+                        SENSORS_SCH311X_IN(0), RW,
+                        NOSYSCTL, VALUE(2), 2, "in0_max", 3 },
+    { SENSORS_SCH311X_IN_MAX(1), "Vccp_max", SENSORS_SCH311X_IN(1),
+                        SENSORS_SCH311X_IN(1), RW,
+                        NOSYSCTL, VALUE(2), 2, "in1_max", 3 },
+    { SENSORS_SCH311X_IN_MAX(2), "VCC_max", SENSORS_SCH311X_IN(2),
+                        SENSORS_SCH311X_IN(2), RW,
+                        NOSYSCTL, VALUE(2), 2, "in2_max", 3 },
+    { SENSORS_SCH311X_IN_MAX(3), "5V_max", SENSORS_SCH311X_IN(3),
+                        SENSORS_SCH311X_IN(3), RW,
+                        NOSYSCTL, VALUE(2), 2, "in3_max", 3 },
+    { SENSORS_SCH311X_IN_MAX(4), "12V_max", SENSORS_SCH311X_IN(4), 
+                        SENSORS_SCH311X_IN(4), RW,

lm-sensors_SVN_modif/lib/chips.c static sensors_chip_feature abituguru_fe · line 5902

Quoted 10 lines
lm-sensors_SVN_modif/lib/chips.c renamed from lm-sensors_SVN/lib/chips.c +10 -0
+                        NOSYSCTL, VALUE(2), 2, "in4_max", 3 },
+    { SENSORS_SCH311X_IN_MAX(5), "VRT_max", SENSORS_SCH311X_IN(5),
+                        SENSORS_SCH311X_IN(5), RW,
+                        NOSYSCTL, VALUE(2), 2, "in5_max", 3 },
+    { SENSORS_SCH311X_IN_MAX(6), "Vbat_max", SENSORS_SCH311X_IN(6),
+                        SENSORS_SCH311X_IN(6), RW,
+                        NOSYSCTL, VALUE(2), 2, "in6_max", 3 },
+    { SENSORS_SCH311X_IN_ALARM(0), "2.5V_alarm", SENSORS_SCH311X_IN(0),
+                        SENSORS_SCH311X_IN(0), RW,
+                        NOSYSCTL, VALUE(3), 2, "in0_alarm", 3 },

Alarms are not scaled, so the second mapping field shouldn't be set to SENSORS_SCH311X_IN(0), but to NOMAP. Same for all other alarms, of course. Also, magnitude is definitely 0 for alarms, and I doubt they are writable.

Quoted 10 lines
lm-sensors_SVN_modif/lib/chips.c renamed from lm-sensors_SVN/lib/chips.c +10 -0
+    { SENSORS_SCH311X_IN_ALARM(1), "Vccp_alarm", SENSORS_SCH311X_IN(1),
+                        SENSORS_SCH311X_IN(1), RW,
+                        NOSYSCTL, VALUE(3), 2, "in1_alarm", 3 },
+    { SENSORS_SCH311X_IN_ALARM(2), "VCC_alarm", SENSORS_SCH311X_IN(2),
+                        SENSORS_SCH311X_IN(2), RW,
+                        NOSYSCTL, VALUE(3), 2, "in2_alarm", 3 },
+    { SENSORS_SCH311X_IN_ALARM(3), "5V_alarm", SENSORS_SCH311X_IN(3),
+                        SENSORS_SCH311X_IN(3), RW,
+                        NOSYSCTL, VALUE(3), 2, "in3_alarm", 3 },
+    { SENSORS_SCH311X_IN_ALARM(4), "12V_alarm", SENSORS_SCH311X_IN(4), 

lm-sensors_SVN_modif/lib/chips.c static sensors_chip_feature abituguru_fe · line 5922

Quoted 10 lines
lm-sensors_SVN_modif/lib/chips.c renamed from lm-sensors_SVN/lib/chips.c +10 -0
+                        SENSORS_SCH311X_IN(4), RW,
+                        NOSYSCTL, VALUE(3), 2, "in4_alarm", 3 },
+    { SENSORS_SCH311X_IN_ALARM(5), "VRT_alarm", SENSORS_SCH311X_IN(5),
+                        SENSORS_SCH311X_IN(5), RW,
+                        NOSYSCTL, VALUE(3), 2, "in5_alarm", 3 },
+    { SENSORS_SCH311X_IN_ALARM(6), "Vbat_alarm", SENSORS_SCH311X_IN(6),
+                        SENSORS_SCH311X_IN(6), RW, 
+                        NOSYSCTL, VALUE(3), 2, "in6_alarm", 3 },
+    { SENSORS_SCH311X_TEMP(1), "temp1", NOMAP, NOMAP,
+                         R, NOSYSCTL, VALUE(5), 2, "temp1_input", 0 },

Magnitude for temperatures in Linux 2.6 is fixed to 3. You don't need to mention the Linux 2.6 name and magnitude, BTW, libsensors will guess them.

lm-sensors_SVN_modif/lib/chips.c static sensors_chip_feature abituguru_fe · line 5929

Quoted 7 lines
lm-sensors_SVN_modif/lib/chips.c renamed from lm-sensors_SVN/lib/chips.c +7 -0
+    { SENSORS_SCH311X_TEMP(2), "temp2", NOMAP, NOMAP, 
+                         R, NOSYSCTL, VALUE(4), 2, "temp2_input", 0 },
+    { SENSORS_SCH311X_TEMP(3), "temp3", NOMAP, NOMAP,
+                         R, NOSYSCTL, VALUE(5), 2, "temp3_input", 0 },
+    { SENSORS_SCH311X_TEMP_MIN(1), "temp1_min", SENSORS_SCH311X_TEMP(1),
+                         SENSORS_SCH311X_TEMP(1), RW, 
+                         NOSYSCTL, VALUE(1), 2, "temp1_low", 0 },

Sysfs file name should be "temp1_min", not "temp1_low".

lm-sensors_SVN_modif/lib/chips.c static sensors_chip_feature abituguru_fe · line 5932

Quoted 3 lines
lm-sensors_SVN_modif/lib/chips.c renamed from lm-sensors_SVN/lib/chips.c +3 -0
+    { SENSORS_SCH311X_TEMP_MAX(1), "temp1_max", SENSORS_SCH311X_TEMP(1),
+                         SENSORS_SCH311X_TEMP(1), RW, 
+                         NOSYSCTL, VALUE(2), 2, "temp1_high", 0 },

And here "temp1_max" instead of "temp1_high". But again you don't need to mention them, libsensors will guess them from the symbol name.

lm-sensors_SVN_modif/lib/chips.c static sensors_chip_feature abituguru_fe · line 5938

Quoted 6 lines
lm-sensors_SVN_modif/lib/chips.c renamed from lm-sensors_SVN/lib/chips.c +6 -0
+    { SENSORS_SCH311X_TEMP_ALARM(1), "temp1_alarm", SENSORS_SCH311X_TEMP(1),
+                         SENSORS_SCH311X_TEMP(1), RW, 
+                         NOSYSCTL, VALUE(3), 2, "temp1_alarm", 0 },
+    { SENSORS_SCH311X_TEMP_ERROR(1), "temp1_error", SENSORS_SCH311X_TEMP(1),
+                         SENSORS_SCH311X_TEMP(1), RW, 
+                         NOSYSCTL, VALUE(4), 2, "temp1_error", 0 },

This name doesn't exist in our Linux 2.6 sysfs file name standard. If this "error" refers to an invalid wiring of the thermal sensor (i.e. input value is invalid) the file should be named temp1_input_fault. I also doubt the alarm and error files are writable, and the Linux 2.4 magnitude is wrong (should be 0).

Quoted 8 lines
lm-sensors_SVN_modif/lib/chips.c renamed from lm-sensors_SVN/lib/chips.c +8 -0
+    { SENSORS_SCH311X_TEMP_MIN(2), "temp2_min", SENSORS_SCH311X_TEMP(2),
+                         SENSORS_SCH311X_TEMP(2), RW, 
+                         NOSYSCTL, VALUE(1), 2, "temp2_low", 0 },
+    { SENSORS_SCH311X_TEMP_MAX(2), "temp2_max", SENSORS_SCH311X_TEMP(2),
+                         SENSORS_SCH311X_TEMP(2), RW, 
+                         NOSYSCTL, VALUE(2), 2, "temp2_high", 0 },
+    { SENSORS_SCH311X_TEMP_ALARM(2), "temp2_alarm", SENSORS_SCH311X_TEMP(2),
+                         SENSORS_SCH311X_TEMP(2), RW, 

lm-sensors_SVN_modif/lib/chips.c static sensors_chip_feature abituguru_fe · line 5956

Quoted 10 lines
lm-sensors_SVN_modif/lib/chips.c renamed from lm-sensors_SVN/lib/chips.c +10 -0
+                         NOSYSCTL, VALUE(3), 2, "temp2_alarm", 0 },
+    { SENSORS_SCH311X_TEMP_MIN(3), "temp3_min", SENSORS_SCH311X_TEMP(3),
+                         SENSORS_SCH311X_TEMP(3), RW, 
+                         NOSYSCTL, VALUE(1), 2, "temp3_low", 0 },
+    { SENSORS_SCH311X_TEMP_MAX(3), "temp3_max", SENSORS_SCH311X_TEMP(3),
+                         SENSORS_SCH311X_TEMP(3), RW, 
+                         NOSYSCTL, VALUE(2), 2, "temp3_high", 0 },
+    { SENSORS_SCH311X_TEMP_ALARM(3), "temp3_alarm", SENSORS_SCH311X_TEMP(2),
+                         SENSORS_SCH311X_TEMP(2), RW, 
+                         NOSYSCTL, VALUE(3), 2, "temp3_alarm", 0 },

Copy'n'paste error, should be SENSORS_SCH311X_TEMP(3).

Quoted 81 lines
lm-sensors_SVN_modif/lib/chips.c renamed from lm-sensors_SVN/lib/chips.c +7 -0
+    { SENSORS_SCH311X_TEMP_ERROR(3), "temp3_error", SENSORS_SCH311X_TEMP(3),
+                         SENSORS_SCH311X_TEMP(3), RW, 
+                         NOSYSCTL, VALUE(4), 2, "temp3_error", 0 },
+    { 0 }
+  };
+
 
 sensors_chip_features sensors_chip_features_list[] >  {
@@ -5943,5 +6064,6 @@ sensors_chip_features sensors_chip_featu
  { SENSORS_SMSC47B397_PREFIX, smsc47b397_features },
  { SENSORS_F71805F_PREFIX, f71805f_features },
  { SENSORS_ABITUGURU_PREFIX, abituguru_features },
+ { SENSORS_SCH311X_PREFIX, sch311x_features },
  { 0 }
 };

diff -uprN -X dontdiff_my ./lm-sensors_SVN/lib/chips.h ./lm-sensors_SVN_modif/lib/chips.h

lm-sensors_SVN_modif/lib/chips.h renamed from lm-sensors_SVN/lib/chips.h +16 -0
@@ -2187,4 +2187,20 @@
 #define SENSORS_ABITUGURU_FAN_ALARM(n)		(0xA0 + (n)) /* R */
 #define SENSORS_ABITUGURU_FAN_MIN(n)		(0xB0 + (n)) /* RW */
 
+/* SMSC SCH311x chips */
+#define SENSORS_SCH311X_PREFIX "sch311x"
+
+/* for n from 0 to 6 */
+#define SENSORS_SCH311X_IN(n)		(1  + (n))	/* R */
+#define SENSORS_SCH311X_IN_MIN(n)	(10 + (n))	/* RW */
+#define SENSORS_SCH311X_IN_MAX(n)	(20 + (n))	/* RW */
+#define SENSORS_SCH311X_IN_ALARM(n)	(30 + (n))	/* R */
+
+/* for n from 1 to 3 */
+#define SENSORS_SCH311X_TEMP(n)		(50 + (n))	/* R */
+#define SENSORS_SCH311X_TEMP_MIN(n)	(60 + (n))	/* RW */
+#define SENSORS_SCH311X_TEMP_MAX(n)	(70 + (n))	/* RW */
+#define SENSORS_SCH311X_TEMP_ALARM(n)	(80 + (n))	/* R */
+#define SENSORS_SCH311X_TEMP_ERROR(n)	(90 + (n))	/* R */
+
 #endif /* def LIB_SENSORS_CHIPS_H */

diff -uprN -X dontdiff_my ./lm-sensors_SVN/prog/detect/sensors-detect ./lm-sensors_SVN_modif/prog/detect/sensors-detect

lm-sensors_SVN_modif/prog/detect/sensors-detect renamed from lm-sensors_SVN/prog/detect/sensors-detect +18 -0
@@ -1926,6 +1926,24 @@ $chip_kern26_w83791d = {
         logdev => 0x08,
       },
       {
+        name => "SMSC SCH3112 Super IO",
+        driver => "sch311x",
+        devid => 0x7c,
+        logdev => 0x0a,
+      },
+      {
+        name => "SMSC SCH3114 Super IO",
+        driver => "sch311x",
+        devid => 0x7d,
+        logdev => 0x0a,
+      },
+      {
+        name => "SMSC SCH3116 Super IO",
+        driver => "sch311x",
+        devid => 0x7f,
+        logdev => 0x0a,
+      },
+      {
         name => "SMSC LPC47M584-NC Super IO",
         # No datasheet
         devid => 0x76,

diff -uprN -X dontdiff_my ./lm-sensors_SVN/prog/sensors/chips.c ./lm-sensors_SVN_modif/prog/sensors/chips.c

lm-sensors_SVN_modif/prog/sensors/chips.c renamed from lm-sensors_SVN/prog/sensors/chips.c +7 -0
@@ -6041,6 +6041,52 @@ void print_abituguru(const sensors_chip_
       SENSORS_ABITUGURU_FAN_ALARM(i), SENSORS_ABITUGURU_FAN_MIN(i));
 }
 
+void print_sch311x(const sensors_chip_name *name)
+{
+  char *label;
+  double cur, min, max, alarm;
+  int valid, i;
+
+  for (i = 0; i < 7; i++) {

lm-sensors_SVN_modif/prog/sensors/chips.c void print_abituguru(const sensors_chip_ · line 6060

Quoted 10 lines
lm-sensors_SVN_modif/prog/sensors/chips.c renamed from lm-sensors_SVN/prog/sensors/chips.c +10 -0
+    if (!sensors_get_label_and_valid(*name, SENSORS_SCH311X_IN(i),
+        &label, &valid)
+     && !sensors_get_feature(*name, SENSORS_SCH311X_IN(i), &cur)
+     && !sensors_get_feature(*name, SENSORS_SCH311X_IN_MIN(i), &min)
+     && !sensors_get_feature(*name, SENSORS_SCH311X_IN_MAX(i), &max)) {
+      if (valid) {
+        print_label(label, 10);
+        printf("%+6.2f V  (min = %+6.2f V, max = %+6.2f V)   %s\n",
+               cur, min, max, sensors_get_feature(*name, 
+               SENSORS_SCH311X_IN_ALARM(i), &alarm) ? "NOT SUPPORTED" : 

Why don't you simply get the alarm value together with the other values? The code would be more readable.

lm-sensors_SVN_modif/prog/sensors/chips.c void print_abituguru(const sensors_chip_ · line 6064

Quoted 4 lines
lm-sensors_SVN_modif/prog/sensors/chips.c renamed from lm-sensors_SVN/prog/sensors/chips.c +4 -0
+               alarm ? "ALARM" : "");
+      }
+    } else
+      printf("Can't get in%d data!\n", i);

We usually prefix these messages with "ERROR: ".

lm-sensors_SVN_modif/prog/sensors/chips.c void print_abituguru(const sensors_chip_ · line 6076

Quoted 12 lines
lm-sensors_SVN_modif/prog/sensors/chips.c renamed from lm-sensors_SVN/prog/sensors/chips.c +12 -0
+    free(label);
+  }
+
+  for (i = 1; i <= 3; i++) {
+    if (!sensors_get_label_and_valid(*name, SENSORS_SCH311X_TEMP(i),
+        &label, &valid)
+     && !sensors_get_feature(*name, SENSORS_SCH311X_TEMP(i), &cur)
+     && !sensors_get_feature(*name, SENSORS_SCH311X_TEMP_MAX(i), &max)
+     && !sensors_get_feature(*name, SENSORS_SCH311X_TEMP_MIN(i), &min)) {
+      if (valid) {
+        print_label(label, 10);
+        print_temp_info(cur, max, min, HYST, 0, 0);

Is the low temperature limit really an hysteresis value? You named it everywhere as if it were a min limit. Please clarify. If it's an hysteresis value, the symbold and file names need to be changed. If it's a min value, please use MINMAX instead of HYST here.

lm-sensors_SVN_modif/prog/sensors/chips.c void print_abituguru(const sensors_chip_ · line 6081

Quoted 5 lines
lm-sensors_SVN_modif/prog/sensors/chips.c renamed from lm-sensors_SVN/prog/sensors/chips.c +5 -0
+        printf("%6s", sensors_get_feature(*name, 
+               SENSORS_SCH311X_TEMP_ALARM(i), &alarm) ? "NOT SUPPORTED" : 
+               alarm ? "ALARM" : "");
+        printf("%6s", sensors_get_feature(*name, SENSORS_SCH311X_TEMP_ERROR(i),
+          &alarm) ? "" : (alarm) ? "ERROR" : "" );

Same here, getting the alarm and error/fault values beforehand would make the code much more readable IMHO. You should also check the fault condition first, as it doesn't make much sense to display an alarm if the input has a fault condition to start with.

BTW you're reading the error/fault value even for i=2, while this file doesn't exist, this needs to be fixed.

Quoted 26 lines
lm-sensors_SVN_modif/prog/sensors/chips.c renamed from lm-sensors_SVN/prog/sensors/chips.c +8 -0
+        printf("\n");
+      }
+    } else
+      printf("Can't get temp%d data!\n", i);
+    free(label);
+  }
+}
+
 void print_unknown_chip(const sensors_chip_name *name)
 {
   int a,b,valid;

diff -uprN -X dontdiff_my ./lm-sensors_SVN/prog/sensors/chips.h ./lm-sensors_SVN_modif/prog/sensors/chips.h

lm-sensors_SVN_modif/prog/sensors/chips.h renamed from lm-sensors_SVN/prog/sensors/chips.h +1 -0
@@ -73,5 +73,6 @@ extern void print_adm1031(const sensors_
 extern void print_smsc47b397(const sensors_chip_name *name);
 extern void print_f71805f(const sensors_chip_name *name);
 extern void print_abituguru(const sensors_chip_name *name);
+extern void print_sch311x(const sensors_chip_name *name);
 
 #endif /* def PROG_SENSORS_CHIPS_H */

diff -uprN -X dontdiff_my ./lm-sensors_SVN/prog/sensors/main.c ./lm-sensors_SVN_modif/prog/sensors/main.c

lm-sensors_SVN_modif/prog/sensors/main.c struct match matches[] = { · line 422

Quoted 7 lines
lm-sensors_SVN_modif/prog/sensors/main.c renamed from lm-sensors_SVN/prog/sensors/main.c +1 -0
@@ -416,6 +416,7 @@ struct match matches[] = {
 	{ "smsc47b397", print_smsc47b397 },
 	{ "f71805f", print_f71805f },
  	{ "abituguru", print_abituguru },
+	{ "sch311x", print_sch311x },
 	{ NULL, NULL }
 };
 

Care to provide an updated patch against the current lm_sensors SVN tree?

Thanks,

Signature · 1 line
Jean Delvare
#6 lore raw
In reply to Marcin Dawidowicz

Marcin,

Are you still interested in support for the SMSC sch311x family? I discovered that the dme1737, which I is supported, is pretty identical. It wouldn't take a lot to modify the dme1737 driver to support the sch311x. Let me know if you're still interested and if you have a system to test and I'll give it a shot. Or you can, if you want to.

...juerg

Quoted 665 lines

Hello,

Below you find my SMSC SCH311x chips driver. Currently, it supports voltage, temperature inputs and alarms. There is not implemented support for fans and pwm control (I couldn't test it on my hardware).

Thanks for your feedback,
Marcin

Signed-off-by Marcin Dawidowicz <Marcin.Dawidowicz at kontron.pl>

diff -uprN -X ./linux-2.6.18-rc2-vanilla/Documentation/dontdiff linux-2.6.18-rc2-vanilla/drivers/hwmon/Kconfig linux-2.6.18-rc2-sch311x/drivers/hwmon/Kconfig

drivers/hwmon/Kconfig +11 -0
@@ -396,6 +396,17 @@ config SENSORS_SMSC47B397
 	  This driver can also be built as a module.  If so, the module
 	  will be called smsc47b397.
 
+config SENSORS_SCH311X
+	tristate "SMSC SCH311x family"
+	depends on HWMON && I2C && EXPERIMENTAL
+	select I2C_ISA
+	help
+	  If you say yes here you get support for the SMSC SCH311x family
+	  sensor chip.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called sch311x.
+
 config SENSORS_VIA686A
 	tristate "VIA686A"
 	depends on HWMON && I2C && PCI

diff -uprN -X ./linux-2.6.18-rc2-vanilla/Documentation/dontdiff linux-2.6.18-rc2-vanilla/drivers/hwmon/Makefile linux-2.6.18-rc2-sch311x/drivers/hwmon/Makefile

drivers/hwmon/Makefile +1 -0
@@ -44,6 +44,7 @@ obj-$(CONFIG_SENSORS_SIS5595)	+= sis5595
 obj-$(CONFIG_SENSORS_SMSC47B397)+= smsc47b397.o
 obj-$(CONFIG_SENSORS_SMSC47M1)	+= smsc47m1.o
 obj-$(CONFIG_SENSORS_SMSC47M192)+= smsc47m192.o
+obj-$(CONFIG_SENSORS_SCH311X)	+= sch311x.o
 obj-$(CONFIG_SENSORS_VIA686A)	+= via686a.o
 obj-$(CONFIG_SENSORS_VT8231)	+= vt8231.o
 obj-$(CONFIG_SENSORS_W83627EHF)	+= w83627ehf.o

diff -uprN -X ./linux-2.6.18-rc2-vanilla/Documentation/dontdiff linux-2.6.18-rc2-vanilla/drivers/hwmon/sch311x.c linux-2.6.18-rc2-sch311x/drivers/hwmon/sch311x.c

drivers/hwmon/sch311x.c +619 -0
@@ -0,0 +1,629 @@
+/*
+    sch311x.c - Part of lm_sensors, Linux kernel modules
+			for hardware monitoring
+
+    Supports the SMSC SCH311x Super-I/O chips.
+
+    Author: Marcin Dawidowicz <Marcin.Dawidowicz at kontron.pl>
+	Copyright (C) 2006 Kontron Modular Computers
+
+    derived in part from smsc47m1.c and smsc47b397:
+	Copyright (C) 2002 Mark D. Studebaker <mdsxyz123 at yahoo.com>
+	Copyright (C) 2004 Jean Delvare <khali at linux-fr.org>
+	Copyright (C) 2004 Mark M. Hoffman <mhoffman at lightlink.com>
+
+    This program is free software; you can redistribute it and/or modify
+    it under the terms of the GNU General Public License as published by
+    the Free Software Foundation; either version 2 of the License, or
+    (at your option) any later version.
+
+    This program is distributed in the hope that it will be useful,
+    but WITHOUT ANY WARRANTY; without even the implied warranty of
+    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+    GNU General Public License for more details.
+
+    You should have received a copy of the GNU General Public License
+    along with this program; if not, write to the Free Software
+    Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+*/
+
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/ioport.h>
+#include <linux/jiffies.h>
+#include <linux/i2c.h>
+#include <linux/i2c-isa.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/mutex.h>
+#include <asm/io.h>
+
+/* Address is autodetected, there is no default value */
+static unsigned short address;
+
+/* Miscellaneous defines */
+
+#define SUPERIO_REG_DEVID		0x20
+#define SUPERIO_REG_DEVREV		0x21
+#define SUPERIO_REG_BASE_MSB		0x60
+#define SUPERIO_REG_BASE_LSB		0x61
+#define SUPERIO_REG_LD			0x0A
+
+#define SMSC_EXTENT			0x02	/* hw mon registers size */
+
+#define SCH311X_REG_TEMP(nr)		(0x25 + nr)
+#define SCH311X_REG_TEMP_HIGH(nr)	(0x4f + (nr*2))
+#define SCH311X_REG_TEMP_LOW(nr)	(0x4e + (nr*2))
+#define SCH311X_REG_FANTACH_LSB(nr)	(0x28 + (nr*2))
+#define SCH311X_REG_FANTACH_MSB(nr)	(0x29 + (nr*2))
+#define SCH311X_REG_FANTACH_MIN_LSB(nr)	(0x54 + (nr*2))
+#define SCH311X_REG_FANTACH_MIN_MSB(nr)	(0x55 + (nr*2))
+
+static const u8 sch311x_volt_regs[7] = {
+	0x20	/*	2.5 V */,
+	0x21	/* Vccp	1.5 V */,
+	0x22	/* VCC	3.3 V */,
+	0x23	/*	  5 V */,
+	0x24	/*	 12 V */,
+	0x99	/* VTR	3.3 V */,
+	0x9a	/* Vbat	3.0 V */
+};
+
+/* max volt values multiplied by 1000 */
+static const u16 sch311x_volt_max_vals[7] = {
+	6640	/*	2.5 V */,
+	3000	/* Vccp	1.5 V */,
+	4380	/* VCC	3.3 V */,
+	6640	/*	  5 V */,
+	16000	/*	 12 V */,
+	4380	/* VTR	3.3 V */,
+	4380	/* Vbat	3.0 V */
+};
+
+#define SCH311X_REG_IN(nr)	(sch311x_volt_regs[nr])
+
+static const u8 sch311x_volt_lo_regs[7] = {
+	0x44, 0x46, 0x48, 0x4a, 0x4c, 0x9b, 0x9d
+};
+
+#define SCH311X_REG_MIN(nr)	(sch311x_volt_lo_regs[nr])
+
+static const u8 sch311x_volt_hi_regs[7] = {
+	0x45, 0x47, 0x49, 0x4b, 0x4d, 0x9c, 0x9e
+};
+
+#define SCH311X_REG_MAX(nr)	(sch311x_volt_hi_regs[nr])
+
+/* Interrupt enable voltages */
+#define SCH311X_REG_INT_VOLT_EN	(0x7e)
+
+#define VOLT_EN_2_5V		(1<<2)
+#define VOLT_EN_VCPP		(1<<3)
+#define VOLT_EN_VCC		(1<<7)
+#define VOLT_EN_5V		(1<<5)
+#define VOLT_EN_12V		(1<<6)
+#define VOLT_EN_VRT		(1<<4)
+#define VOLT_EN_VBAT		(1<<1)
+
+/* Interrupt status registers */
+#define SCH311X_REG_ISR1	(0x41)
+#define SCH311X_REG_ISR2	(0x42)
+#define SCH311X_REG_ISR3	(0x83)
+
+/* Alarm bits meaning */
+#define ISR_TEMP3		(6)
+#define ISR_TEMP2		(5)
+#define ISR_TEMP1		(4)
+#define ISR_5V			(3)
+#define ISR_VCC			(2)
+#define ISR_Vccp		(1)
+#define ISR_2_5V		(0)
+
+#define ISR_ERR3		(15)
+#define ISR_ERR1		(14)
+#define ISR_FAN_3		(12)
+#define ISR_FAN_2		(11)
+#define ISR_FAN_1		(10)
+#define ISR_12V			(8)
+
+#define ISR_VRT			(16)
+#define ISR_Vbat		(17)
+
+/* logical device for hardware monitoring is 0x0A */
+#define superio_select() superio_outb(0x07, SUPERIO_REG_LD)
+
+/* Super-I/0 registers and commands */
+#define	REG	0x2e	/* The register to read/write */
+#define	VAL	0x2f	/* The value to read/write */
+
+static inline void
+superio_outb(int reg, int val)
+{
+	outb(reg, REG);
+	outb(val, VAL);
+}
+
+static inline int
+superio_inb(int reg)
+{
+	outb(reg, REG);
+	return inb(VAL);
+}
+
+static inline void
+superio_enter(void)
+{
+	outb(0x55, REG);
+}
+
+static inline void
+superio_exit(void)
+{
+	outb(0xAA, REG);
+}
+
+struct sch311x_data {
+	struct i2c_client client;
+	struct class_device *class_dev;
+	struct mutex lock;
+
+	struct mutex update_lock;
+	unsigned long last_updated;	/* In jiffies */
+	int valid;
+
+	u32 alarms;		/* Register value of interrupt status */
+
+	s8 temp[3];		/* register value */
+	s8 temp_high[3];	/* register value */
+	s8 temp_low[3];		/* register value */
+
+	u8 in[7];		/* register value */
+	u8 in_max[7];		/* register value */
+	u8 in_min[7];		/* register value */
+};
+
+static int sch311x_detect(struct i2c_adapter *adapter);
+static int sch311x_detach_client(struct i2c_client *client);
+
+static struct i2c_driver sch311x_driver = {
+	.driver = {
+		.name	= "sch311x",
+	},
+	.attach_adapter	= sch311x_detect,
+	.detach_client	= sch311x_detach_client,
+};
+
+static int sch311x_read_value(struct i2c_client *client, u8 reg)
+{
+	struct sch311x_data *data = i2c_get_clientdata(client);
+	int res;
+
+	mutex_lock(&data->lock);
+
+	outb(reg, client->addr);
+	res = inb_p(client->addr + 1);
+
+	mutex_unlock(&data->lock);
+	return res;
+}
+
+static void sch311x_write_value(struct i2c_client *client, u8 reg, u8 value)
+{
+	struct sch311x_data *data = i2c_get_clientdata(client);
+
+	mutex_lock(&data->lock);
+
+	outb(reg, client->addr);
+	outb(value, client->addr + 1);
+
+	mutex_unlock(&data->lock);
+}
+
+static struct sch311x_data *sch311x_update_device(struct device *dev)
+{
+ 	struct i2c_client *client = to_i2c_client(dev);
+	struct sch311x_data *data = i2c_get_clientdata(client);
+	int i;
+
+	mutex_lock(&data->update_lock);
+
+	if (time_after(jiffies, data->last_updated + HZ) || !data->valid) {
+		dev_dbg(&client->dev, "starting device update...\n");
+
+		/* read alarms */
+		data->alarms = sch311x_read_value(client,
+				SCH311X_REG_ISR1);
+		data->alarms|= sch311x_read_value(client,
+				SCH311X_REG_ISR2) << 8;
+		data->alarms|= sch311x_read_value(client,
+				SCH311X_REG_ISR3) << 16;
+
+		/* 3 temperature inputs */
+		for (i = 0; i < 3; i++) {
+			data->temp[i] = sch311x_read_value(client,
+					SCH311X_REG_TEMP(i));
+			data->temp_high[i] = sch311x_read_value(client,
+					SCH311X_REG_TEMP_HIGH(i));
+			data->temp_low[i] = sch311x_read_value(client,
+					SCH311X_REG_TEMP_LOW(i));
+		}
+		/* 7 voltage inputs */
+		for (i = 0; i < 7; i++) {
+			data->in[i] = sch311x_read_value(client,
+					SCH311X_REG_IN(i));
+			data->in_max[i] = sch311x_read_value(client,
+					SCH311X_REG_MAX(i));
+			data->in_min[i] = sch311x_read_value(client,
+					SCH311X_REG_MIN(i));
+		}
+
+		/* clear alarms */
+		sch311x_write_value(client, SCH311X_REG_ISR1, 0xff);
+		sch311x_write_value(client, SCH311X_REG_ISR2, 0xff);
+
+		data->last_updated = jiffies;
+		data->valid = 1;
+
+		dev_dbg(&client->dev, "... device update complete\n");
+	}
+
+	mutex_unlock(&data->update_lock);
+
+	return data;
+}
+
+static int temp_from_reg(u8 reg)
+{
+	return (s8)reg * 100;
+}
+
+/* 0 <= nr <= 3 */
+static ssize_t show_temp(struct device *dev, char *buf, int nr)
+{
+	struct sch311x_data *data = sch311x_update_device(dev);
+	return sprintf(buf, "%d\n", temp_from_reg(data->temp[nr]));
+}
+
+static ssize_t show_temp_high(struct device *dev, char *buf, int nr)
+{
+	struct sch311x_data *data = sch311x_update_device(dev);
+	return sprintf(buf, "%d\n", temp_from_reg(data->temp_high[nr]));
+}
+
+static ssize_t show_temp_low(struct device *dev, char *buf, int nr)
+{
+	struct sch311x_data *data = sch311x_update_device(dev);
+	return sprintf(buf, "%d\n", temp_from_reg(data->temp_low[nr]));
+}
+
+#define sysfs_temp(num) \
+static ssize_t show_temp##num(struct device *dev, struct device_attribute *attr, char *buf) \
+{ \
+	return show_temp(dev, buf, num-1); \
+} \
+static ssize_t show_temp_high##num(struct device *dev, struct device_attribute *attr, char *buf) \
+{ \
+	return show_temp_high(dev, buf, num-1); \
+} \
+static ssize_t show_temp_low##num(struct device *dev, struct device_attribute *attr, char *buf) \
+{ \
+	return show_temp_low(dev, buf, num-1); \
+} \
+static DEVICE_ATTR(temp##num##_input, S_IRUGO, show_temp##num, NULL)
+
+sysfs_temp(1);
+sysfs_temp(2);
+sysfs_temp(3);
+
+static void set_temp_high(struct device *dev, const char *buf, int nr)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	s32 val;
+
+	val = simple_strtol(buf, NULL, 10);
+	sch311x_write_value(client, SCH311X_REG_TEMP_HIGH(nr), val/100);
+}
+
+static void set_temp_low(struct device *dev, const char *buf, int nr)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	s32 val;
+
+	val = simple_strtol(buf, NULL, 10);
+	sch311x_write_value(client, SCH311X_REG_TEMP_LOW(nr), val/100);
+}
+
+#define sysfs_set_temp(num) \
+static ssize_t set_temp_high##num(struct device *dev, struct device_attribute *attr, \
+		const char *buf, size_t count) \
+{ \
+	set_temp_high(dev, buf, num - 1); \
+	return count; \
+} \
+static ssize_t set_temp_low##num(struct device *dev, struct device_attribute *attr, \
+		const char *buf, size_t count) \
+{ \
+	set_temp_low(dev, buf, num - 1); \
+	return count; \
+} \
+static DEVICE_ATTR(temp##num##_low, S_IRUGO | S_IWUSR, \
+		show_temp_low##num, set_temp_low##num); \
+static DEVICE_ATTR(temp##num##_high, S_IRUGO | S_IWUSR, \
+		show_temp_high##num, set_temp_high##num)
+
+sysfs_set_temp(1);
+sysfs_set_temp(2);
+sysfs_set_temp(3);
+
+#define device_create_file_temp(client, num) \
+	device_create_file(&client->dev, &dev_attr_temp##num##_input); \
+	device_create_file(&client->dev, &dev_attr_temp##num##_high); \
+	device_create_file(&client->dev, &dev_attr_temp##num##_low)
+
+static int in_from_reg(u8 reg, u16 max_val)
+{
+	return (int) reg * max_val / 255;
+}
+
+/* 0 <= nr <= 7 */
+static ssize_t show_in(struct device *dev, char *buf, int nr)
+{
+	struct sch311x_data *data = sch311x_update_device(dev);
+	return sprintf(buf, "%d\n", in_from_reg(data->in[nr], sch311x_volt_max_vals[nr]));
+}
+
+static ssize_t show_max(struct device *dev, char *buf, int nr)
+{
+	struct sch311x_data *data = sch311x_update_device(dev);
+	return sprintf(buf, "%d\n", in_from_reg(data->in_max[nr], sch311x_volt_max_vals[nr]));
+}
+
+static ssize_t show_min(struct device *dev, char *buf, int nr)
+{
+	struct sch311x_data *data = sch311x_update_device(dev);
+	return sprintf(buf, "%d\n", in_from_reg(data->in_min[nr], sch311x_volt_max_vals[nr]));
+}
+
+#define sysfs_in(num) \
+static ssize_t show_in##num##_input(struct device *dev, struct device_attribute *attr, char *buf) \
+{ \
+	return show_in(dev, buf, num); \
+} \
+static ssize_t show_in##num##_max(struct device *dev, struct device_attribute *attr, char *buf) \
+{ \
+	return show_max(dev, buf, num); \
+} \
+static ssize_t show_in##num##_min(struct device *dev, struct device_attribute *attr, char *buf) \
+{ \
+	return show_min(dev, buf, num); \
+} \
+static DEVICE_ATTR(in##num##_input, S_IRUGO, show_in##num##_input, NULL)
+
+sysfs_in(0);
+sysfs_in(1);
+sysfs_in(2);
+sysfs_in(3);
+sysfs_in(4);
+sysfs_in(5);
+sysfs_in(6);
+
+static void set_min(struct device *dev, const char *buf, int nr)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	u32 val;
+
+	val = simple_strtoul(buf, NULL, 10) * 255 / sch311x_volt_max_vals[nr];
+	sch311x_write_value(client, SCH311X_REG_MIN(nr), val);
+}
+
+static void set_max(struct device *dev, const char *buf, int nr)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	u32 val;
+
+	val = simple_strtoul(buf, NULL, 10) * 255 / sch311x_volt_max_vals[nr];
+	sch311x_write_value(client, SCH311X_REG_MAX(nr), val);
+}
+
+#define sysfs_set_in(num) \
+static ssize_t set_in##num##_min(struct device *dev, struct device_attribute *attr, \
+		const char *buf, size_t count) \
+{ \
+	set_min(dev, buf, num); \
+	return count; \
+} \
+static ssize_t set_in##num##_max(struct device *dev, struct device_attribute *attr, \
+		const char *buf, size_t count) \
+{ \
+	set_max(dev, buf, num); \
+	return count; \
+} \
+static DEVICE_ATTR(in##num##_min, S_IRUGO | S_IWUSR, \
+		show_in##num##_min, set_in##num##_min); \
+static DEVICE_ATTR(in##num##_max, S_IRUGO | S_IWUSR, \
+		show_in##num##_max, set_in##num##_max)
+
+#define device_create_file_in(client, num) \
+	device_create_file(&client->dev, &dev_attr_in##num##_input); \
+	device_create_file(&client->dev, &dev_attr_in##num##_max); \
+	device_create_file(&client->dev, &dev_attr_in##num##_min); \
+	device_create_file(&client->dev, &sensor_dev_attr_in##num##_alarm.dev_attr)
+
+sysfs_set_in(0);
+sysfs_set_in(1);
+sysfs_set_in(2);
+sysfs_set_in(3);
+sysfs_set_in(4);
+sysfs_set_in(5);
+sysfs_set_in(6);
+
+static ssize_t show_alarm(struct device *dev, struct device_attribute *attr, char *buf)
+{
+	struct sch311x_data *data = sch311x_update_device(dev);
+	struct sensor_device_attribute *sensor_attr = to_sensor_dev_attr(attr);
+	int nr = sensor_attr->index;
+	return sprintf(buf, "%u\n", (data->alarms & (1<<nr)) ? 1 : 0);
+}
+
+static SENSOR_DEVICE_ATTR(temp1_alarm, S_IRUGO, show_alarm, NULL, ISR_TEMP1);
+static SENSOR_DEVICE_ATTR(temp2_alarm, S_IRUGO, show_alarm, NULL, ISR_TEMP2);
+static SENSOR_DEVICE_ATTR(temp3_alarm, S_IRUGO, show_alarm, NULL, ISR_TEMP3);
+static SENSOR_DEVICE_ATTR(temp1_error, S_IRUGO, show_alarm, NULL, ISR_ERR1);
+static SENSOR_DEVICE_ATTR(temp3_error, S_IRUGO, show_alarm, NULL, ISR_ERR3);
+static SENSOR_DEVICE_ATTR(in0_alarm, S_IRUGO, show_alarm, NULL, ISR_2_5V);
+static SENSOR_DEVICE_ATTR(in1_alarm, S_IRUGO, show_alarm, NULL, ISR_Vccp);
+static SENSOR_DEVICE_ATTR(in2_alarm, S_IRUGO, show_alarm, NULL, ISR_VCC);
+static SENSOR_DEVICE_ATTR(in3_alarm, S_IRUGO, show_alarm, NULL, ISR_5V);
+static SENSOR_DEVICE_ATTR(in4_alarm, S_IRUGO, show_alarm, NULL, ISR_12V);
+static SENSOR_DEVICE_ATTR(in5_alarm, S_IRUGO, show_alarm, NULL, ISR_VRT);
+static SENSOR_DEVICE_ATTR(in6_alarm, S_IRUGO, show_alarm, NULL, ISR_Vbat);
+
+static int sch311x_detach_client(struct i2c_client *client)
+{
+	struct sch311x_data *data = i2c_get_clientdata(client);
+	int err;
+
+	hwmon_device_unregister(data->class_dev);
+
+	if ((err = i2c_detach_client(client)))
+		return err;
+
+	release_region(client->addr, SMSC_EXTENT);
+	kfree(data);
+
+	return 0;
+}
+
+static int sch311x_detect(struct i2c_adapter *adapter)
+{
+	struct i2c_client *new_client;
+	struct sch311x_data *data;
+	int err = 0;
+	u8 mon_volt;
+
+	if (!request_region(address, SMSC_EXTENT,
+			    sch311x_driver.driver.name)) {
+		dev_err(&adapter->dev, "Region 0x%x already in use!\n",
+			address);
+		return -EBUSY;
+	}
+
+	if (!(data = kzalloc(sizeof(struct sch311x_data), GFP_KERNEL))) {
+		err = -ENOMEM;
+		goto error_release;
+	}
+
+	new_client = &data->client;
+	i2c_set_clientdata(new_client, data);
+	new_client->addr = address;
+	mutex_init(&data->lock);
+	new_client->adapter = adapter;
+	new_client->driver = &sch311x_driver;
+	new_client->flags = 0;
+
+	strlcpy(new_client->name, "sch311x", I2C_NAME_SIZE);
+
+	mutex_init(&data->update_lock);
+
+	if ((err = i2c_attach_client(new_client)))
+		goto error_free;
+
+	mon_volt = superio_inb(SCH311X_REG_INT_VOLT_EN);
+
+	data->class_dev = hwmon_device_register(&new_client->dev);
+	if (IS_ERR(data->class_dev)) {
+		err = PTR_ERR(data->class_dev);
+		goto error_detach;
+	}
+
+	/* temp values */
+	device_create_file_temp(new_client, 1);
+	device_create_file(&new_client->dev, &sensor_dev_attr_temp1_alarm.dev_attr);
+	device_create_file(&new_client->dev, &sensor_dev_attr_temp1_error.dev_attr);
+	device_create_file_temp(new_client, 2);
+	device_create_file(&new_client->dev, &sensor_dev_attr_temp2_alarm.dev_attr);
+	device_create_file_temp(new_client, 3);
+	device_create_file(&new_client->dev, &sensor_dev_attr_temp3_alarm.dev_attr);
+	device_create_file(&new_client->dev, &sensor_dev_attr_temp3_error.dev_attr);
+
+	/* voltage values */
+	if (mon_volt & VOLT_EN_2_5V) device_create_file_in(new_client, 0);
+	if (mon_volt & VOLT_EN_VCPP) device_create_file_in(new_client, 1);
+	if (mon_volt & VOLT_EN_VCC) device_create_file_in(new_client, 2);
+	if (mon_volt & VOLT_EN_5V) device_create_file_in(new_client, 3);
+	if (mon_volt & VOLT_EN_12V) device_create_file_in(new_client, 4);
+	if (mon_volt & VOLT_EN_VRT) device_create_file_in(new_client, 5);
+	if (mon_volt & VOLT_EN_VBAT) device_create_file_in(new_client, 6);
+
+	return 0;
+
+error_detach:
+	i2c_detach_client(new_client);
+error_free:
+	kfree(data);
+error_release:
+	release_region(address, SMSC_EXTENT);
+	return err;
+}
+
+static int __init sch311x_find(unsigned short *addr)
+{
+	u8 id, rev;
+
+	superio_enter();
+	id = superio_inb(SUPERIO_REG_DEVID);
+
+	if ((id & 0xfc) != 0x7c) {
+		superio_exit();
+		return -ENODEV;
+	}
+
+	rev = superio_inb(SUPERIO_REG_DEVREV);
+
+	superio_select();
+
+	/*
+	 * base address to "Runtime Registers"
+	 * plus offset to HWM Index/Data
+	 * registers
+	 */
+	*addr = ((superio_inb(SUPERIO_REG_BASE_MSB) << 8)
+		 |  superio_inb(SUPERIO_REG_BASE_LSB))
+		 + 0x70;
+
+	printk(KERN_INFO "sch311x: found SMSC %s "
+		"(base address 0x%04x, revision %u)\n",
+		id = 0x7c ? "SCH3112" :
+		id = 0x7d ? "SCH3114" :
+		id = 0x7f ? "SCH3116" :
+		"SCH311X id=0x7e <Reserved>"
+		, *addr, rev);
+
+	superio_exit();
+
+	return 0;
+}
+
+static int __init sch311x_init(void)
+{
+	int ret;
+
+	if ((ret = sch311x_find(&address)))
+		return ret;
+
+	return i2c_isa_add_driver(&sch311x_driver);
+}
+
+static void __exit sch311x_exit(void)

drivers/hwmon/sch311x.c line 629

Quoted 10 lines
drivers/hwmon/sch311x.c +10 -0
+{
+	i2c_isa_del_driver(&sch311x_driver);
+}
+
+MODULE_AUTHOR("Marcin Dawidowicz <Marcin.Dawidowicz at kontron.pl>");
+MODULE_DESCRIPTION("SMSC SCH311x driver");
+MODULE_LICENSE("GPL");
+
+module_init(sch311x_init);
+module_exit(sch311x_exit);

_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors

#7 lore raw
In reply to Marcin Dawidowicz

Hello Juerg,

Yes, I'm interested in support for those chips. I have board equipped with SCH3112 on my side and I can do tests of such driver (except fans support).
Feel free to contact me.

Regards,
Marcin

Quoted 11 lines · Juerg Haefliger

Marcin,

Are you still interested in support for the SMSC sch311x family? I discovered that the dme1737, which I is supported, is pretty identical. It wouldn't take a lot to modify the dme1737 driver to support the sch311x. Let me know if you're still interested and if you have a system to test and I'll give it a shot. Or you can, if you want to.

...juerg

_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors

#8 lore raw
In reply to Marcin Dawidowicz

Hi Marcin,

Quoted 5 lines

Hello Juerg,

Yes, I'm interested in support for those chips. I have board equipped with SCH3112 on my side and I can do tests of such driver (except fans support).

Good. I'll try to create a patch over the next couple of days.

...juerg

Quoted 19 lines

Feel free to contact me.

Regards,
Marcin

Quoted 11 lines · Juerg Haefliger

Marcin,

Are you still interested in support for the SMSC sch311x family? I discovered that the dme1737, which I is supported, is pretty identical. It wouldn't take a lot to modify the dme1737 driver to support the sch311x. Let me know if you're still interested and if you have a system to test and I'll give it a shot. Or you can, if you want to.

...juerg

_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors