cxgb3 - on board memory, MAC and PHY
Subsystems (2)
PATCH 6/10 cxgb3 - on board memory, MAC and PHY
From: Divy Le Ray <[email protected]>
This patch implements on board memory, MAC and PHY management for the Chelsio T3 network adapter's driver.
Signed-off-by Divy Le Ray <[email protected]>
---
drivers/net/cxgb3/ael1002.c | 231 ++++++++++++++++++++++ drivers/net/cxgb3/mc5.c | 456 +++++++++++++++++++++++++++++++++++++++++++ drivers/net/cxgb3/vsc8211.c | 208 ++++++++++++++++++++ drivers/net/cxgb3/xgmac.c | 389 +++++++++++++++++++++++++++++++++++++ 4 files changed, 1284 insertions(+), 0 deletions(-)
drivers/net/cxgb3/ael1002.c new file +231 -0
@@ -0,0 +1,231 @@ +/* +* This file is part of the Chelsio T3 Ethernet driver. +* +* Copyright (C) 2005-2006 Chelsio Communications. All rights reserved. +* +* This program is distributed in the hope that it will be useful, but WITHOUT +* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or +* FITNESS FOR A PARTICULAR PURPOSE. See the LICENSE file included in this +* release for licensing terms and conditions. +*/ + +#include "common.h" +#include "regs.h" + +enum { +AEL100X_TX_DISABLE =9 , +AEL100X_TX_CONFIG1 =0xc002 , +AEL1002_PWR_DOWN_HI =0xc011 , +AEL1002_PWR_DOWN_LO =0xc012 , +AEL1002_XFI_EQL =0xc015 , +AEL1002_LB_EN =0xc017 , + +LASI_CTRL =0x9002 , +LASI_STAT =0x9005 +}; + +static void ael100x_txon (struct cphy *phy) +{ +int tx_on_gpio = phy->addr ==0 ?F_GPIO7_OUT_VAL :F_GPIO2_OUT_VAL ; + +msleep (100 ); +t3_set_reg_field (phy->adapter,A_T3DBG_GPIO_EN ,0 , tx_on_gpio); +msleep (30 ); +} + +static int ael1002_power_down (struct cphy *phy,int enable) +{ +int err; + + err =mdio_write (phy,MDIO_DEV_PMA_PMD ,AEL100X_TX_DISABLE , !!enable); +if (!err) + err =t3_mdio_change_bits (phy,MDIO_DEV_PMA_PMD ,MII_BMCR , +BMCR_PDOWN , enable ?BMCR_PDOWN :0 ); +return err; +} + +static int ael1002_reset (struct cphy *phy,int wait) +{ +int err; + +if ((err =ael1002_power_down (phy,0 )) || + (err =mdio_write (phy,MDIO_DEV_PMA_PMD ,AEL100X_TX_CONFIG1 ,1 )) || + (err =mdio_write (phy,MDIO_DEV_PMA_PMD ,AEL1002_PWR_DOWN_HI ,0 )) || + (err =mdio_write (phy,MDIO_DEV_PMA_PMD ,AEL1002_PWR_DOWN_LO ,0 )) || + (err =mdio_write (phy,MDIO_DEV_PMA_PMD ,AEL1002_XFI_EQL ,0x18 )) || + (err =t3_mdio_change_bits (phy,MDIO_DEV_PMA_PMD ,AEL1002_LB_EN , +0 ,1 <<5 ))) +return err; +return 0 ; +} + +static int ael1002_intr_noop (struct cphy *phy) +{ +return 0 ; +} + +static int ael100x_get_link_status (struct cphy *phy,int *link_ok, +int *speed,int *duplex,int *fc) +{ +if (link_ok) { +unsigned int status; +int err =mdio_read (phy,MDIO_DEV_PMA_PMD ,MII_BMSR , &status); + +/* +* BMSR_LSTATUS is latch-low, so if it is 0 we need to read it +* once more to get the current link state. +*/ +if (!err && !(status &BMSR_LSTATUS )) + err =mdio_read (phy,MDIO_DEV_PMA_PMD ,MII_BMSR , + &status); +if (err) +return err; + *link_ok = !!(status &BMSR_LSTATUS ); + } +if (speed) + *speed =SPEED_10000 ; +if (duplex) + *duplex =DUPLEX_FULL ; +return 0 ; +} + +static struct cphy_ops ael1002_ops = { + .reset = ael1002_reset, + .intr_enable = ael1002_intr_noop, + .intr_disable = ael1002_intr_noop, + .intr_clear = ael1002_intr_noop, + .intr_handler = ael1002_intr_noop, + .get_link_status = ael100x_get_link_status, + .power_down = ael1002_power_down, +}; + +void t3_ael1002_phy_prep (struct cphy *phy,struct adapter *adapter, +int phy_addr,const struct mdio_ops *mdio_ops) +{ +cphy_init (phy, adapter, phy_addr, &ael1002_ops, mdio_ops); +ael100x_txon (phy); +} + +static int ael1006_reset (struct cphy *phy,int wait) +{ +return t3_phy_reset (phy,MDIO_DEV_PMA_PMD , wait); +} + +static int ael1006_intr_enable (struct cphy *phy) +{ +return mdio_write (phy,MDIO_DEV_PMA_PMD ,LASI_CTRL ,1 ); +} + +static int ael1006_intr_disable (struct cphy *phy) +{ +return mdio_write (phy,MDIO_DEV_PMA_PMD ,LASI_CTRL ,0 ); +} + +static int ael1006_intr_clear (struct cphy *phy) +{ +u32 val; + +return mdio_read (phy,MDIO_DEV_PMA_PMD ,LASI_STAT , &val); +} + +static int ael1006_intr_handler (struct cphy *phy) +{ +unsigned int status; +int err =mdio_read (phy,MDIO_DEV_PMA_PMD ,LASI_STAT , &status); + +if (err) +return err; +return (status &1 ) ? cphy_cause_link_change :0 ; +} + +static int ael1006_power_down (struct cphy *phy,int enable) +{ +return t3_mdio_change_bits (phy,MDIO_DEV_PMA_PMD ,MII_BMCR , +BMCR_PDOWN , enable ?BMCR_PDOWN :0 ); +} + +static struct cphy_ops ael1006_ops = { + .reset = ael1006_reset, + .intr_enable = ael1006_intr_enable, + .intr_disable = ael1006_intr_disable, + .intr_clear = ael1006_intr_clear, + .intr_handler = ael1006_intr_handler, + .get_link_status = ael100x_get_link_status, + .power_down = ael1006_power_down, +}; + +void t3_ael1006_phy_prep (struct cphy *phy,struct adapter *adapter, +int phy_addr,const struct mdio_ops *mdio_ops) +{ +cphy_init (phy, adapter, phy_addr, &ael1006_ops, mdio_ops); +ael100x_txon (phy); +} + +static struct cphy_ops qt2045_ops = { + .reset = ael1006_reset, + .intr_enable = ael1006_intr_enable, + .intr_disable = ael1006_intr_disable, + .intr_clear = ael1006_intr_clear, + .intr_handler = ael1006_intr_handler, + .get_link_status = ael100x_get_link_status, + .power_down = ael1006_power_down, +}; + +void t3_qt2045_phy_prep (struct cphy *phy,struct adapter *adapter,int phy_addr, +const struct mdio_ops *mdio_ops) +{ +unsigned int stat; + +cphy_init (phy, adapter, phy_addr, &qt2045_ops, mdio_ops); + +/* +* Some cards where the PHY is supposed to be at address 0 actually +* have it at 1. +*/ +if (!phy_addr && !mdio_read (phy,MDIO_DEV_PMA_PMD ,MII_BMSR , &stat) && + stat ==0xffff ) + phy->addr =1 ; +} + +static int xaui_direct_reset (struct cphy *phy,int wait) +{ +return 0 ; +} + +static int xaui_direct_get_link_status (struct cphy *phy,int *link_ok, +int *speed,int *duplex,int *fc) +{ +if (link_ok) { +unsigned int status; + + status =t3_read_reg (phy->adapter, +XGM_REG (A_XGM_SERDES_STAT0 , phy->addr)); + *link_ok = !(status &F_LOWSIG0 ); + } +if (speed) + *speed =SPEED_10000 ; +if (duplex) + *duplex =DUPLEX_FULL ; +return 0 ; +} + +static int xaui_direct_power_down (struct cphy *phy,int enable) +{ +return 0 ; +} + +static struct cphy_ops xaui_direct_ops = { + .reset = xaui_direct_reset, + .intr_enable = ael1002_intr_noop, + .intr_disable = ael1002_intr_noop, + .intr_clear = ael1002_intr_noop, + .intr_handler = ael1002_intr_noop, + .get_link_status = xaui_direct_get_link_status, + .power_down = xaui_direct_power_down, +}; + +void t3_xaui_direct_phy_prep (struct cphy *phy,struct adapter *adapter, +int phy_addr,const struct mdio_ops *mdio_ops) +{ +cphy_init (phy, adapter,1 , &xaui_direct_ops, mdio_ops); +}
drivers/net/cxgb3/mc5.c new file +456 -0
456 lines not on this page · raw message
drivers/net/cxgb3/vsc8211.c new file +208 -0
208 lines not on this page · raw message
drivers/net/cxgb3/xgmac.c new file +389 -0
389 lines not on this page · raw message