Skip to contentSkip to conversation

PCI MMConfig per-chipset support - v2

PATCH New Olivier Galibert 1 participant 6 messages Dec 7, 2006

lore
Share & tools
lore
#0 lore raw

cover PCI MMConfig per-chipset support - v2

I'll try to be less messy this time.

OG.

1/5: PCI MMConfig: Share what's shareable.
Share code between i386 and x86-64

2/5: PCI MMConfig: Only call unreachable_devices() when type 1 is available.
Trivial fix.

3/5: PCI MMConfig: Only map what's necessary.
Trivial fix too.

4/5: PCI MMConfig: Detect and support the E7520 and the 945G/GZ/P/PL
The actual per-chipset support.

5/5: PCI MMConfig: Reserve resources but only when we're sure about them.
Add the resources in /proc/iomem when the chipset in known.

#1 lore raw

PATCH 1/5 PCI MMConfig: Share what's shareable.

i386 and x86-64 pci mmconfig code have a lot in common. So share what's shareable between the two.

---
 arch/i386/pci/Makefile          |    2 +-
 arch/i386/pci/mmconfig-shared.c |   86 +++++++++++++++++++++++++++++++++++++++
 arch/i386/pci/mmconfig.c        |   74 ++-------------------------------
 arch/i386/pci/pci.h             |    6 +++
 arch/x86_64/pci/Makefile        |    3 +-
 arch/x86_64/pci/mmconfig.c      |   71 +++++---------------------------
 6 files changed, 109 insertions(+), 133 deletions(-)
arch/i386/pci/Makefile +1 -1
index 1594d2f..44650e0 100644
@@ -1,7 +1,7 @@
 obj-y				:= i386.o init.o
 
 obj-$(CONFIG_PCI_BIOS)		+= pcbios.o
-obj-$(CONFIG_PCI_MMCONFIG)	+= mmconfig.o direct.o
+obj-$(CONFIG_PCI_MMCONFIG)	+= mmconfig.o direct.o mmconfig-shared.o
 obj-$(CONFIG_PCI_DIRECT)	+= direct.o
 
 pci-y				:= fixup.o
arch/i386/pci/mmconfig-shared.c new file +86 -0

86 lines not on this page · raw message

arch/i386/pci/mmconfig.c +4 -70

99 lines not on this page · raw message

arch/i386/pci/pci.h +6 -0
index a0a2518..0270c80 100644
@@ -94,3 +94,9 @@ extern void pci_pcbios_init(void);
 extern void pci_mmcfg_init(int type);
 extern void pcibios_sort(void);
 
+/* pci-mmconfig.c */
+
+#define PCI_MMCFG_MAX_CHECK_BUS 16
+extern DECLARE_BITMAP(pci_mmcfg_fallback_slots, 32*PCI_MMCFG_MAX_CHECK_BUS);
+
+extern int pci_mmcfg_arch_init(void);
arch/x86_64/pci/Makefile +2 -1
index 149aba0..c9eddc8 100644
@@ -11,7 +11,7 @@ obj-y		+= fixup.o init.o
 obj-$(CONFIG_ACPI)	+= acpi.o
 obj-y			+= legacy.o irq.o common.o early.o
 # mmconfig has a 64bit special
-obj-$(CONFIG_PCI_MMCONFIG) += mmconfig.o direct.o
+obj-$(CONFIG_PCI_MMCONFIG) += mmconfig.o direct.o mmconfig-shared.o
 
 obj-$(CONFIG_NUMA)	+= k8-bus.o
 
@@ -24,3 +24,4 @@ fixup-y  += ../../i386/pci/fixup.o
 i386-y  += ../../i386/pci/i386.o
 init-y += ../../i386/pci/init.o
 early-y += ../../i386/pci/early.o
+mmconfig-shared-y += ../../i386/pci/mmconfig-shared.o
arch/x86_64/pci/mmconfig.c +10 -61

103 lines not on this page · raw message

Signature · 1 line
1.4.4.1.g278f
#2 lore raw

PATCH 2/5 PCI MMConfig: Only call unreachable_devices() when type 1 is available.

In reply to Olivier Galibert

unreachable_devices compares between the results of pci configuration accesses through type1 and mmconfig, so it should be called only if type1 actually works in the first place.

---
 arch/i386/pci/mmconfig-shared.c |    3 ++-
 1 files changed, 2 insertions(+), 1 deletions(-)
arch/i386/pci/mmconfig-shared.c +2 -1
index b3ab210..7b19639 100644
@@ -80,7 +80,8 @@ void __init pci_mmcfg_init(int type)
 	}
 
 	if (pci_mmcfg_arch_init()) {
-		unreachable_devices();
+		if (type == 1)
+			unreachable_devices();
 		pci_probe = (pci_probe & ~PCI_PROBE_MASK) | PCI_PROBE_MMCONF;
 	}
 }
Signature · 1 line
1.4.4.1.g278f
#3 lore raw

PATCH 3/5 PCI MMConfig: Only map what's necessary.

In reply to Olivier Galibert

The x86-64 mmconfig code always map a range of MMCONFIG_APER_MAX bytes, i.e. 256MB, whatever the number of accessible busses is. Fix it, and add the end of the zone in the printk while we're at it.

---
 arch/x86_64/pci/mmconfig.c |   12 +++++-------
 1 files changed, 5 insertions(+), 7 deletions(-)
arch/x86_64/pci/mmconfig.c +5 -7
index c71c181..3d13220 100644
@@ -13,10 +13,6 @@
 
 #include "pci.h"
 
-/* aperture is up to 256MB but BIOS may reserve less */
-#define MMCONFIG_APER_MIN	(2 * 1024*1024)
-#define MMCONFIG_APER_MAX	(256 * 1024*1024)
-
 /* Verify the first 16 busses. We assume that systems with more busses
    get MCFG right. */
 #define PCI_MMCFG_MAX_CHECK_BUS 16
@@ -143,17 +139,19 @@ int __init pci_mmcfg_arch_init(void)
 	}
 
 	for (i = 0; i < pci_mmcfg_config_num; ++i) {
+		u32 size = (pci_mmcfg_config[0].end_bus_number - pci_mmcfg_config[0].start_bus_number + 1) << 20;
 		pci_mmcfg_virt[i].cfg = &pci_mmcfg_config[i];
 		pci_mmcfg_virt[i].virt = ioremap_nocache(pci_mmcfg_config[i].base_address,
-							 MMCONFIG_APER_MAX);
+							 size);
 		if (!pci_mmcfg_virt[i].virt) {
 			printk(KERN_ERR "PCI: Cannot map mmconfig aperture for "
 					"segment %d\n",
 			       pci_mmcfg_config[i].pci_segment_group_number);
 			return 0;
 		}
-		printk(KERN_INFO "PCI: Using MMCONFIG at %x\n",
-		       pci_mmcfg_config[i].base_address);
+		printk(KERN_INFO "PCI: Using MMCONFIG at %x-%x\n",
+		       pci_mmcfg_config[i].base_address,
+		       pci_mmcfg_config[i].base_address + size - 1);
 	}
 
 	raw_pci_ops = &pci_mmcfg;
Signature · 1 line
1.4.4.1.g278f
#4 lore raw

PATCH 4/5 PCI MMConfig: Detect and support the E7520 and the 945G/GZ/P/PL

In reply to Olivier Galibert

It seems that the only way to reliably support mmconfig in the presence of funky biosen is to detect the hostbridge and read where the window is mapped from its registers. Do that for the E7520 and the 945G/GZ/P/PL for a start.

---
 arch/i386/pci/mmconfig-shared.c |  116 ++++++++++++++++++++++++++++++++++++++-
 1 files changed, 113 insertions(+), 3 deletions(-)
arch/i386/pci/mmconfig-shared.c +113 -3
index 7b19639..302d495 100644
@@ -3,6 +3,7 @@
  *                     MMCONFIG - common code between i386 and x86-64.
  * 
  * This code does:
+ * - known chipset handling
  * - ACPI decoding and validation
  *
  * Per-architecture code takes care of the mappings and accesses
@@ -55,12 +56,121 @@ static __init void unreachable_devices(void)
 	}
 }
 
+static __init const char *pci_mmcfg_e7520(void)
+{
+	u32 win;
+	pci_conf1_read(0, 0, PCI_DEVFN(0,0), 0xce, 2, &win);
+
+	pci_mmcfg_config_num = 1;
+	pci_mmcfg_config = kzalloc(sizeof(pci_mmcfg_config[0]), GFP_KERNEL);
+	pci_mmcfg_config[0].base_address = (win & 0xf000) << 16;
+	pci_mmcfg_config[0].pci_segment_group_number = 0;
+	pci_mmcfg_config[0].start_bus_number = 0;
+	pci_mmcfg_config[0].end_bus_number = 255;
+
+	return "Intel Corporation E7520 Memory Controller Hub";
+}
+
+static __init const char *pci_mmcfg_intel_945(void)
+{
+	u32 pciexbar, mask = 0, len = 0;
+
+	pci_mmcfg_config_num = 1;
+
+	pci_conf1_read(0, 0, PCI_DEVFN(0,0), 0x48, 4, &pciexbar);
+
+	/* Enable bit */
+	if (!(pciexbar & 1))
+		pci_mmcfg_config_num = 0;
+
+	/* Size bits */
+	switch ((pciexbar >> 1) & 3) {
+	case 0:
+		mask = 0xf0000000U;
+		len  = 0x10000000U;
+		break;
+	case 1:
+		mask = 0xf8000000U;
+		len  = 0x08000000U;
+		break;
+	case 2:
+		mask = 0xfc000000U;
+		len  = 0x04000000U;
+		break;
+	default:
+		pci_mmcfg_config_num = 0;
+	}
+
+	/* Errata #2, things break when not aligned on a 256Mb boundary */
+	/* Can only happen in 64M/128M mode */
+
+	if ((pciexbar & mask) & 0x0fffffffU)
+		pci_mmcfg_config_num = 0;
+
+	if (pci_mmcfg_config_num) {
+		pci_mmcfg_config = kzalloc(sizeof(pci_mmcfg_config[0]), GFP_KERNEL);
+		pci_mmcfg_config[0].base_address = pciexbar & mask;
+		pci_mmcfg_config[0].pci_segment_group_number = 0;
+		pci_mmcfg_config[0].start_bus_number = 0;
+		pci_mmcfg_config[0].end_bus_number = (len >> 20) - 1;
+	}
+
+	return "Intel Corporation 945G/GZ/P/PL Express Memory Controller Hub";
+}
+
+struct pci_mmcfg_hostbridge_probe {
+	u32 vendor;
+	u32 device;
+	const char *(*probe)(void);
+};
+
+static __initdata struct pci_mmcfg_hostbridge_probe pci_mmcfg_probes[] = {
+	{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7520_MCH, pci_mmcfg_e7520 },
+	{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82945G_HB, pci_mmcfg_intel_945 },
+};
+
+static int __init pci_mmcfg_check_hostbridge(void)
+{
+	u32 l;
+	u16 vendor, device;
+	int i;
+	const char *name;
+
+	pci_conf1_read(0, 0, PCI_DEVFN(0,0), 0, 4, &l);
+	vendor = l & 0xffff;
+	device = (l >> 16) & 0xffff;
+
+	pci_mmcfg_config_num = 0;
+	pci_mmcfg_config = NULL;
+	name = NULL;
+
+	for (i = 0; !name && i < sizeof(pci_mmcfg_probes) / sizeof(pci_mmcfg_probes[0]); i++)
+		if ((pci_mmcfg_probes[i].vendor == PCI_ANY_ID || pci_mmcfg_probes[i].vendor == vendor) &&
+		    (pci_mmcfg_probes[i].device == PCI_ANY_ID || pci_mmcfg_probes[i].device == device))
+			name = pci_mmcfg_probes[i].probe();
+
+	if (name) {
+		if (pci_mmcfg_config_num)
+			printk(KERN_INFO "PCI: Found %s with MMCONFIG support.\n", name);
+		else
+			printk(KERN_INFO "PCI: Found %s without MMCONFIG support.\n", name);
+	}
+
+	return name != NULL;
+}
+
 void __init pci_mmcfg_init(int type)
 {
+	int known_bridge = 0;
+
 	if ((pci_probe & PCI_PROBE_MMCONF) == 0)
 		return;
 
-	acpi_table_parse(ACPI_MCFG, acpi_parse_mcfg);
+	if (type == 1 && pci_mmcfg_check_hostbridge())
+		known_bridge = 1;
+
+	if (!known_bridge)
+		acpi_table_parse(ACPI_MCFG, acpi_parse_mcfg);
 
 	if ((pci_mmcfg_config_num == 0) ||
 	    (pci_mmcfg_config == NULL) ||
@@ -68,8 +178,8 @@ void __init pci_mmcfg_init(int type)
 		return;
 
 	/* Only do this check when type 1 works. If it doesn't work
-           assume we run on a Mac and always use MCFG */
-	if (type == 1 &&
+	   assume we run on a Mac and always use MCFG */
+	if (type == 1 && !known_bridge &&
 	    !e820_all_mapped(pci_mmcfg_config[0].base_address,
 			     pci_mmcfg_config[0].base_address + MMCONFIG_APER_MIN,
 			     E820_RESERVED)) {
Signature · 1 line
1.4.4.1.g278f
#5 lore raw

PATCH 5/5 PCI MMConfig: Reserve resources but only when we're sure about them.

In reply to Olivier Galibert

Put back the resource reservation as per 4c6e052adfe285ede5884e4e8c4d33af33932c13 but use it *only* when the range(s) come from a chipset probe instead of the bios.

---
 arch/i386/pci/mmconfig-shared.c |   33 +++++++++++++++++++++++++++++++++
 1 files changed, 33 insertions(+), 0 deletions(-)
arch/i386/pci/mmconfig-shared.c +33 -0
index 302d495..0da1e3b 100644
@@ -159,6 +159,37 @@ static int __init pci_mmcfg_check_hostbridge(void)
 	return name != NULL;
 }
 
+static __init void pci_mmcfg_insert_resources(void)
+{
+#define PCI_MMCFG_RESOURCE_NAME_LEN 19
+	int i;
+	struct resource *res;
+	char *names;
+	unsigned num_buses;
+
+	res = kcalloc(PCI_MMCFG_RESOURCE_NAME_LEN + sizeof(*res),
+			pci_mmcfg_config_num, GFP_KERNEL);
+
+	if (!res) {
+		printk(KERN_ERR "PCI: Unable to allocate MMCONFIG resources\n");
+		return;
+	}
+
+	names = (void *)&res[pci_mmcfg_config_num];
+	for (i = 0; i < pci_mmcfg_config_num; i++, res++) {
+		num_buses = pci_mmcfg_config[i].end_bus_number -
+		    pci_mmcfg_config[i].start_bus_number + 1;
+		res->name = names;
+		snprintf(names, PCI_MMCFG_RESOURCE_NAME_LEN, "PCI MMCONFIG %u",
+			pci_mmcfg_config[i].pci_segment_group_number);
+		res->start = pci_mmcfg_config[i].base_address;
+		res->end = res->start + (num_buses << 20) - 1;
+		res->flags = IORESOURCE_MEM | IORESOURCE_BUSY;
+		insert_resource(&iomem_resource, res);
+		names += PCI_MMCFG_RESOURCE_NAME_LEN;
+	}
+}
+
 void __init pci_mmcfg_init(int type)
 {
 	int known_bridge = 0;
@@ -192,6 +223,8 @@ void __init pci_mmcfg_init(int type)
 	if (pci_mmcfg_arch_init()) {
 		if (type == 1)
 			unreachable_devices();
+		if (known_bridge)
+			pci_mmcfg_insert_resources();
 		pci_probe = (pci_probe & ~PCI_PROBE_MASK) | PCI_PROBE_MMCONF;
 	}
 }
Signature · 1 line
1.4.4.1.g278f