Add support for Korenix 16C950-based PCI cards
PATCH 1/1 Add support for Korenix 16C950-based PCI cards
Linus, Andrew,
This patch adds initial support to 8250-pci for the Korenix Jetcard PCI serial cards. The JC12xx cards are standard RS232-based serial cards utilising the Oxford 16C950 device.
The JC14xx are RS422/RS485-based cards, but in order for these to be supported natively, we will need additional tweaks to the 8250 layers so we can specify some values for the 950's registers. Hence, these two entries are commented out.
drivers/serial/8250_pci.c | 24 ++++++++++++++++++++++++ 1 file changed, 24 insertions(+)
drivers/serial/8250_pci.c +24 -0
@@ -2239,6 +2239,30 @@ static struct pci_device_id serial_pci_t pbn_b0_bt_1_460800 },/* +* Korenix Jetcard F0/F1 cards (JC1204, JC1208, JC1404, JC1408). +* Cards are identified by their subsystem vendor IDs, which +* (in hex) match the model number. +* +* Note that JC140x are RS422/485 cards which require ox950 +* ACR = 0x10, and as such are not currently fully supported. +*/ + {PCI_VENDOR_ID_KORENIX ,PCI_DEVICE_ID_KORENIX_JETCARDF0 , +0x1204 ,0x0004 ,0 ,0 , + pbn_b0_4_921600 }, + { PCI_VENDOR_ID_KORENIX, PCI_DEVICE_ID_KORENIX_JETCARDF0, +0x1208 ,0x0004 ,0 ,0 , + pbn_b0_4_921600 }, +/* { PCI_VENDOR_ID_KORENIX, PCI_DEVICE_ID_KORENIX_JETCARDF0, +0x1402, 0x0002, 0, 0, +pbn_b0_2_921600 }, */ +/* { PCI_VENDOR_ID_KORENIX, PCI_DEVICE_ID_KORENIX_JETCARDF0, +0x1404, 0x0004, 0, 0, +pbn_b0_4_921600 }, */ + { PCI_VENDOR_ID_KORENIX, PCI_DEVICE_ID_KORENIX_JETCARDF1, +0x1208 ,0x0004 ,0 ,0 , + pbn_b0_4_921600 }, + +/* * Dell Remote Access Card 4 - [email protected] */ { PCI_VENDOR_ID_DELL, PCI_DEVICE_ID_DELL_RAC4,
Quoted 10 lines · Russell King
Linus, Andrew,
This patch adds initial support to 8250-pci for the Korenix Jetcard PCI serial cards. The JC12xx cards are standard RS232-based serial cards utilising the Oxford 16C950 device.
The JC14xx are RS422/RS485-based cards, but in order for these to be supported natively, we will need additional tweaks to the 8250 layers so we can specify some values for the 950's registers. Hence, these two entries are commented out.
IIRC 16c950 just need two bits in ACR set properly. Will attached patch do the trick ?
Quoted 40 lines
Signed-off-by Russell King <[email protected]>drivers/serial/8250_pci.c | 24 ++++++++++++++++++++++++ 1 file changed, 24 insertions(+)drivers/serial/8250_pci.c +24
-0@@ -2239,6 +2239,30 @@ static struct pci_device_id serial_pci_t pbn_b0_bt_1_460800 },/* +* Korenix Jetcard F0/F1 cards (JC1204, JC1208, JC1404, JC1408). +* Cards are identified by their subsystem vendor IDs, which +* (in hex) match the model number. +* +* Note that JC140x are RS422/485 cards which require ox950 +* ACR = 0x10, and as such are not currently fully supported. +*/ + {PCI_VENDOR_ID_KORENIX ,PCI_DEVICE_ID_KORENIX_JETCARDF0 , +0x1204 ,0x0004 ,0 ,0 , + pbn_b0_4_921600 }, + { PCI_VENDOR_ID_KORENIX, PCI_DEVICE_ID_KORENIX_JETCARDF0, +0x1208 ,0x0004 ,0 ,0 , + pbn_b0_4_921600 }, +/* { PCI_VENDOR_ID_KORENIX, PCI_DEVICE_ID_KORENIX_JETCARDF0, +0x1402, 0x0002, 0, 0, +pbn_b0_2_921600 }, */ +/* { PCI_VENDOR_ID_KORENIX, PCI_DEVICE_ID_KORENIX_JETCARDF0, +0x1404, 0x0004, 0, 0, +pbn_b0_4_921600 }, */ + { PCI_VENDOR_ID_KORENIX, PCI_DEVICE_ID_KORENIX_JETCARDF1, +0x1208 ,0x0004 ,0 ,0 , + pbn_b0_4_921600 }, + +/* * Dell Remote Access Card 4 - [email protected] */ { PCI_VENDOR_ID_DELL, PCI_DEVICE_ID_DELL_RAC4,
Signature · 2 lines
Andrey Panin | Linux and UNIX system administrator [email protected] | PGP key: wwwkeys.pgp.net
drivers/serial/8250.c +2 -1
@@ -1548,7 +1548,7 @@ static int serial8250_startup(struct uarif (up->port.type ==PORT_16C950 ) {/* Wake up and initialize UART */ - up->acr =0 ; + up->acr = port->initial_acr;serial_outp (up,UART_LCR ,0xBF );serial_outp (up,UART_EFR ,UART_EFR_ECB );serial_outp (up,UART_IER ,0 );
@@ -2599,6 +2599,7 @@ int serial8250_register_port(struct uart uart->port.iotype = port->iotype; uart->port.flags = port->flags |UPF_BOOT_AUTOCONF ; uart->port.mapbase = port->mapbase; + uart->port.initial_acr = port->initial_acr;if (port->dev) uart->port.dev = port->dev;
drivers/serial/8250.h +2 -0
@@ -29,6 +29,8 @@ struct old_serial_port {unsigned short iomem_reg_shift; }; +#define initial_acr unused[0] +/* * This replaces serial_uart_config in include/linux/serial.h */
Quoted 7 lines · Andrey Panin
Quoted 6 lines · Russell King
Linus, Andrew,
This patch adds initial support to 8250-pci for the Korenix Jetcard PCI serial cards. The JC12xx cards are standard RS232-based serial cards utilising the Oxford 16C950 device.
Quoted 7 lines
Quoted 4 lines
The JC14xx are RS422/RS485-based cards, but in order for these to be supported natively, we will need additional tweaks to the 8250 layers so we can specify some values for the 950's registers. Hence, these two entries are commented out.
IIRC 16c950 just need two bits in ACR set properly. Will attached patch do the trick ?
I, too, also have a patch which does something similar. I'm going to hold off on that until post 2.6.20 though, especially as I have no way to test it.
Signature · 3 lines
Russell King Linux kernel 2.6 ARM Linux - http://www.arm.linux.org.uk/ maintainer of: