Skip to contentSkip to conversation

libata updates

PATCH In review Jeff Garzik 2 participants 2 messages Dec 14, 2006 – Dec 15, 2006

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 libata updates

Includes some pre-window-closing stuff (new drivers), but I was waiting on some bug fixes before pushing.

Please pull from 'upstream-linus' branch of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev.git upstream-linus

to receive the following updates:

 drivers/ata/Kconfig            |   20 ++-
 drivers/ata/Makefile           |    2 +
 drivers/ata/ahci.c             |    2 -
 drivers/ata/ata_piix.c         |   24 ++-
 drivers/ata/libata-core.c      |   16 +-
 drivers/ata/libata-scsi.c      |    4 +-
 drivers/ata/pata_ali.c         |    4 +-
 drivers/ata/pata_cs5520.c      |    2 +-
 drivers/ata/pata_cs5530.c      |    8 +-
 drivers/ata/pata_hpt366.c      |    2 +-
 drivers/ata/pata_hpt37x.c      |    4 +-
 drivers/ata/pata_hpt3x3.c      |    2 +-
 drivers/ata/pata_it8213.c      |  354 +++++++++++++++++++++++++
 drivers/ata/pata_jmicron.c     |    2 +-
 drivers/ata/pata_marvell.c     |    4 +-
 drivers/ata/pata_mpc52xx.c     |  563 ++++++++++++++++++++++++++++++++++++++++
 drivers/ata/pata_serverworks.c |    2 +-
 drivers/ata/pata_sil680.c      |    2 +-
 drivers/ata/pata_sis.c         |    2 +-
 drivers/ata/pata_via.c         |   10 +-
 drivers/ata/pata_winbond.c     |   16 +-
 drivers/ata/sata_nv.c          |   18 +-
 drivers/ata/sata_sis.c         |   79 ++++--
 drivers/ata/sata_svw.c         |   41 +++-
 drivers/ata/sata_via.c         |    2 +-
 include/linux/libata.h         |    2 +-
 include/linux/pci_ids.h        |    1 +
 27 files changed, 1099 insertions(+), 89 deletions(-)
 create mode 100644 drivers/ata/pata_it8213.c
 create mode 100644 drivers/ata/pata_mpc52xx.c

Alan (1):
pata_it8213: Add new driver for the IT8213 card

Jason Gaston (1):
ata_piix: IDE mode SATA patch for Intel ICH9

Jeff Garzik (3):
[libata] use kmap_atomic(KM_IRQ0) in SCSI simulator
[libata] trim trailing whitespace
[libata] sata_svw: Disable ATAPI DMA on current boards (errata workaround)

Sylvain Munaut (1):
libata: Add support for the MPC52xx ATA controller

Tejun Heo (3):
ata_piix: use piix_host_stop() in ich_pata_ops
libata: don't initialize sg in ata_exec_internal() if DMA_NONE (take #2)
ahci: do not mangle saved HOST_CAP while resetting controller

Uwe Koziolek (1):

      sata_sis: support SiS966/966L
drivers/ata/Kconfig +19 -1
index 984ab28..fb1de86 100644
@@ -292,7 +292,7 @@ config PATA_ISAPNP
 	  If unsure, say N.
 
 config PATA_IT821X
-	tristate "IT821x PATA support (Experimental)"
+	tristate "IT8211/2 PATA support (Experimental)"
 	depends on PCI && EXPERIMENTAL
 	help
 	  This option enables support for the ITE 8211 and 8212
@@ -301,6 +301,15 @@ config PATA_IT821X
 
 	  If unsure, say N.
 
+config PATA_IT8213
+	tristate "IT8213 PATA support (Experimental)"
+	depends on PCI && EXPERIMENTAL
+	help
+	  This option enables support for the ITE 821 PATA
+          controllers via the new ATA layer.
+
+	  If unsure, say N.
+
 config PATA_JMICRON
 	tristate "JMicron PATA support"
 	depends on PCI
@@ -337,6 +346,15 @@ config PATA_MARVELL
 
 	  If unsure, say N.
 
+config PATA_MPC52xx
+	tristate "Freescale MPC52xx SoC internal IDE"
+	depends on PPC_MPC52xx
+	help
+	  This option enables support for integrated IDE controller
+	  of the Freescale MPC52xx SoC.
+
+	  If unsure, say N.
+
 config PATA_MPIIX
 	tristate "Intel PATA MPIIX support"
 	depends on PCI
drivers/ata/Makefile +2 -0
index bc3d81a..a0df15d 100644
@@ -33,11 +33,13 @@ obj-$(CONFIG_PATA_HPT3X2N)	+= pata_hpt3x2n.o
 obj-$(CONFIG_PATA_HPT3X3)	+= pata_hpt3x3.o
 obj-$(CONFIG_PATA_ISAPNP)	+= pata_isapnp.o
 obj-$(CONFIG_PATA_IT821X)	+= pata_it821x.o
+obj-$(CONFIG_PATA_IT8213)	+= pata_it8213.o
 obj-$(CONFIG_PATA_JMICRON)	+= pata_jmicron.o
 obj-$(CONFIG_PATA_NETCELL)	+= pata_netcell.o
 obj-$(CONFIG_PATA_NS87410)	+= pata_ns87410.o
 obj-$(CONFIG_PATA_OPTI)		+= pata_opti.o
 obj-$(CONFIG_PATA_OPTIDMA)	+= pata_optidma.o
+obj-$(CONFIG_PATA_MPC52xx)	+= pata_mpc52xx.o
 obj-$(CONFIG_PATA_MARVELL)	+= pata_marvell.o
 obj-$(CONFIG_PATA_MPIIX)	+= pata_mpiix.o
 obj-$(CONFIG_PATA_OLDPIIX)	+= pata_oldpiix.o
drivers/ata/ahci.c +0 -2
index f36da48..dbae6d9 100644
@@ -645,8 +645,6 @@ static int ahci_reset_controller(void __iomem *mmio, struct pci_dev *pdev)
 	u32 cap_save, impl_save, tmp;
 
 	cap_save = readl(mmio + HOST_CAP);
-	cap_save &= ( (1<<28) | (1<<17) );
-	cap_save |= (1 << 27);
 	impl_save = readl(mmio + HOST_PORTS_IMPL);
 
 	/* global controller reset */
drivers/ata/ata_piix.c +18 -6
index c7de0bb..7959e4c 100644
@@ -226,14 +226,26 @@ static const struct pci_device_id piix_pci_tbl[] = {
 	{ 0x8086, 0x27c0, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata_ahci },
 	/* 2801GBM/GHM (ICH7M, identical to ICH6M) */
 	{ 0x8086, 0x27c4, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6m_sata_ahci },
-	/* Enterprise Southbridge 2 (where's the datasheet?) */
+	/* Enterprise Southbridge 2 (631xESB/632xESB) */
 	{ 0x8086, 0x2680, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich6_sata_ahci },
-	/* SATA Controller 1 IDE (ICH8, no datasheet yet) */
+	/* SATA Controller 1 IDE (ICH8) */
 	{ 0x8086, 0x2820, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
-	/* SATA Controller 2 IDE (ICH8, ditto) */
+	/* SATA Controller 2 IDE (ICH8) */
 	{ 0x8086, 0x2825, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
-	/* Mobile SATA Controller IDE (ICH8M, ditto) */
+	/* Mobile SATA Controller IDE (ICH8M) */
 	{ 0x8086, 0x2828, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+	/* SATA Controller IDE (ICH9) */
+	{ 0x8086, 0x2920, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+	/* SATA Controller IDE (ICH9) */
+	{ 0x8086, 0x2921, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+	/* SATA Controller IDE (ICH9) */
+	{ 0x8086, 0x2926, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+	/* SATA Controller IDE (ICH9M) */
+	{ 0x8086, 0x2928, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+	/* SATA Controller IDE (ICH9M) */
+	{ 0x8086, 0x292d, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+	/* SATA Controller IDE (ICH9M) */
+	{ 0x8086, 0x292e, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
 
 	{ }	/* terminate list */
 };
@@ -330,7 +342,7 @@ static const struct ata_port_operations ich_pata_ops = {
 
 	.port_start		= ata_port_start,
 	.port_stop		= ata_port_stop,
-	.host_stop		= ata_host_stop,
+	.host_stop		= piix_host_stop,
 };
 
 static const struct ata_port_operations piix_sata_ops = {
@@ -620,7 +632,7 @@ static int piix_pata_prereset(struct ata_port *ap)
 
 	if (!pci_test_config_bits(pdev, &piix_enable_bits[ap->port_no]))
 		return -ENOENT;
-		
+
 	ap->cbl = ATA_CBL_PATA40;
 	return ata_std_prereset(ap);
 }
drivers/ata/libata-core.c +11 -5
index 011c0a8..fd20e7a 100644
@@ -1332,7 +1332,7 @@ unsigned ata_exec_internal_sg(struct ata_device *dev,
 }
 
 /**
- *	ata_exec_internal_sg - execute libata internal command
+ *	ata_exec_internal - execute libata internal command
  *	@dev: Device to which the command is sent
  *	@tf: Taskfile registers for the command and the result
  *	@cdb: CDB for packet command
@@ -1353,11 +1353,17 @@ unsigned ata_exec_internal(struct ata_device *dev,
 			   struct ata_taskfile *tf, const u8 *cdb,
 			   int dma_dir, void *buf, unsigned int buflen)
 {
-	struct scatterlist sg;
+	struct scatterlist *psg = NULL, sg;
+	unsigned int n_elem = 0;
 
-	sg_init_one(&sg, buf, buflen);
+	if (dma_dir != DMA_NONE) {
+		WARN_ON(!buf);
+		sg_init_one(&sg, buf, buflen);
+		psg = &sg;
+		n_elem++;
+	}
 
-	return ata_exec_internal_sg(dev, tf, cdb, dma_dir, &sg, 1);
+	return ata_exec_internal_sg(dev, tf, cdb, dma_dir, psg, n_elem);
 }
 
 /**
@@ -5773,7 +5779,7 @@ int ata_device_add(const struct ata_probe_ent *ent)
 	int rc;
 
 	DPRINTK("ENTER\n");
-	
+
 	if (ent->irq == 0) {
 		dev_printk(KERN_ERR, dev, "is not available: No interrupt assigned.\n");
 		return 0;
drivers/ata/libata-scsi.c +2 -2
index 664e137..a4790be 100644
@@ -1539,7 +1539,7 @@ static unsigned int ata_scsi_rbuf_get(struct scsi_cmnd *cmd, u8 **buf_out)
 		struct scatterlist *sg;
 
 		sg = (struct scatterlist *) cmd->request_buffer;
-		buf = kmap_atomic(sg->page, KM_USER0) + sg->offset;
+		buf = kmap_atomic(sg->page, KM_IRQ0) + sg->offset;
 		buflen = sg->length;
 	} else {
 		buf = cmd->request_buffer;
@@ -1567,7 +1567,7 @@ static inline void ata_scsi_rbuf_put(struct scsi_cmnd *cmd, u8 *buf)
 		struct scatterlist *sg;
 
 		sg = (struct scatterlist *) cmd->request_buffer;
-		kunmap_atomic(buf - sg->offset, KM_USER0);
+		kunmap_atomic(buf - sg->offset, KM_IRQ0);
 	}
 }
 
drivers/ata/pata_ali.c +2 -2
index c5d61d1..2035417 100644
@@ -504,7 +504,7 @@ static struct ata_port_operations ali_c5_port_ops = {
  *	Perform the setup on the device that must be done both at boot
  *	and at resume time.
  */
- 
+
 static void ali_init_chipset(struct pci_dev *pdev)
 {
 	u8 rev, tmp;
@@ -655,7 +655,7 @@ static int ali_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
         	port_info[0] = port_info[1] = &info_c5;
 
 	ali_init_chipset(pdev);
-	
+
 	isa_bridge = pci_get_device(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1533, NULL);
 	if (isa_bridge && rev >= 0x20 && rev < 0xC2) {
 		/* Are we paired with a UDMA capable chip */
drivers/ata/pata_cs5520.c +1 -1
index 9f165a8..476b879 100644
@@ -305,7 +305,7 @@ static void __devexit cs5520_remove_one(struct pci_dev *pdev)
  *	Do any reconfiguration work needed by a resume from RAM. We need
  *	to restore DMA mode support on BIOSen which disabled it
  */
- 
+
 static int cs5520_reinit_one(struct pci_dev *pdev)
 {
 	u8 pcicfg;
drivers/ata/pata_cs5530.c +4 -4
index 1c62801..9b9d911 100644
@@ -247,7 +247,7 @@ static int cs5530_is_palmax(void)
  *	Perform the chip initialisation work that is shared between both
  *	setup and resume paths
  */
- 
+
 static int cs5530_init_chip(void)
 {
 	struct pci_dev *master_0 = NULL, *cs5530_0 = NULL, *dev = NULL;
@@ -357,11 +357,11 @@ static int cs5530_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
 		.port_ops = &cs5530_port_ops
 	};
 	static struct ata_port_info *port_info[2] = { &info, &info };
-	
+
 	/* Chip initialisation */
 	if (cs5530_init_chip())
 		return -ENODEV;
-		
+
 	if (cs5530_is_palmax())
 		port_info[1] = &info_palmax_secondary;
 
@@ -375,7 +375,7 @@ static int cs5530_reinit_one(struct pci_dev *pdev)
 	BUG_ON(cs5530_init_chip());
 	return ata_pci_device_resume(pdev);
 }
-	
+
 static const struct pci_device_id cs5530[] = {
 	{ PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5530_IDE), },
 
drivers/ata/pata_hpt366.c +1 -1
index 2663599..8cf167e 100644
@@ -232,7 +232,7 @@ static int hpt36x_pre_reset(struct ata_port *ap)
 
 	if (!pci_test_config_bits(pdev, &hpt36x_enable_bits[ap->port_no]))
 		return -ENOENT;
-		
+
 	pci_read_config_byte(pdev, 0x5A, &ata66);
 	if (ata66 & (1 << ap->port_no))
 		ap->cbl = ATA_CBL_PATA40;
drivers/ata/pata_hpt37x.c +2 -2
index 47082df..e51651b 100644
@@ -459,7 +459,7 @@ static int hpt37x_pre_reset(struct ata_port *ap)
 	};
 	if (!pci_test_config_bits(pdev, &hpt37x_enable_bits[ap->port_no]))
 		return -ENOENT;
-		
+
 	pci_read_config_byte(pdev, 0x5B, &scr2);
 	pci_write_config_byte(pdev, 0x5B, scr2 & ~0x01);
 	/* Cable register now active */
@@ -504,7 +504,7 @@ static int hpt374_pre_reset(struct ata_port *ap)
 
 	if (!pci_test_config_bits(pdev, &hpt37x_enable_bits[ap->port_no]))
 		return -ENOENT;
-		
+
 	/* Do the extra channel work */
 	pci_read_config_word(pdev, 0x52, &mcr3);
 	pci_read_config_word(pdev, 0x56, &mcr6);
drivers/ata/pata_hpt3x3.c +1 -1
index 5f1d385..5caf167 100644
@@ -164,7 +164,7 @@ static struct ata_port_operations hpt3x3_port_ops = {
  *
  *	Perform the setup required at boot and on resume.
  */
- 
+
 static void hpt3x3_init_chipset(struct pci_dev *dev)
 {
 	u16 cmd;
drivers/ata/pata_it8213.c new file +354 -0

354 lines not on this page · raw message

drivers/ata/pata_jmicron.c +1 -1
index 2d661cb..efb1b6d 100644
@@ -229,7 +229,7 @@ static int jmicron_init_one (struct pci_dev *pdev, const struct pci_device_id *i
 static int jmicron_reinit_one(struct pci_dev *pdev)
 {
 	u32 reg;
-	
+
 	switch(pdev->device) {
 		case PCI_DEVICE_ID_JMICRON_JMB368:
 			break;
drivers/ata/pata_marvell.c +2 -2
index 1c810ea..af93533 100644
@@ -45,10 +45,10 @@ static int marvell_pre_reset(struct ata_port *ap)
 	for(i = 0; i <= 0x0F; i++)
 		printk("%02X:%02X ", i, readb(barp + i));
 	printk("\n");
-	
+
 	devices = readl(barp + 0x0C);
 	pci_iounmap(pdev, barp);
-	
+
 	if ((pdev->device == 0x6145) && (ap->port_no == 0) &&
 	    (!(devices & 0x10)))	/* PATA enable ? */
 		return -ENOENT;
drivers/ata/pata_mpc52xx.c new file +563 -0

563 lines not on this page · raw message

drivers/ata/pata_serverworks.c +1 -1
index f02b6a3..8019197 100644
@@ -559,7 +559,7 @@ static int serverworks_reinit_one(struct pci_dev *pdev)
 {
 	/* Force master latency timer to 64 PCI clocks */
 	pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x40);
-	
+
 	switch (pdev->device)
 	{
 		case PCI_DEVICE_ID_SERVERWORKS_OSB4IDE:
drivers/ata/pata_sil680.c +1 -1
index 32cf0bf..ae07f63 100644
@@ -270,7 +270,7 @@ static struct ata_port_operations sil680_port_ops = {
  *	is powered up on boot and when we resume in case we resumed from RAM.
  *	Returns the final clock settings.
  */
- 
+
 static u8 sil680_init_chip(struct pci_dev *pdev)
 {
 	u32 class_rev	= 0;
drivers/ata/pata_sis.c +1 -1
index 916cedb..c434c4e 100644
@@ -847,7 +847,7 @@ static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
 	struct sis_chipset *chipset = NULL;
 
 	static struct sis_chipset sis_chipsets[] = {
-	
+
 		{ 0x0968, &sis_info133 },
 		{ 0x0966, &sis_info133 },
 		{ 0x0965, &sis_info133 },
drivers/ata/pata_via.c +5 -5
index cc09d47..9905fa8 100644
@@ -384,11 +384,11 @@ static struct ata_port_operations via_port_ops_noirq = {
 static void via_config_fifo(struct pci_dev *pdev, unsigned int flags)
 {
 	u8 enable;
-	
+
 	/* 0x40 low bits indicate enabled channels */
 	pci_read_config_byte(pdev, 0x40 , &enable);
 	enable &= 3;
-	
+
 	if (flags & VIA_SET_FIFO) {
 		u8 fifo_setting[4] = {0x00, 0x60, 0x00, 0x20};
 		u8 fifo;
@@ -509,7 +509,7 @@ static int via_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
 
 	/* Initialise the FIFO for the enabled channels. */
 	via_config_fifo(pdev, config->flags);
-	
+
 	/* Clock set up */
 	switch(config->flags & VIA_UDMA) {
 		case VIA_UDMA_NONE:
@@ -568,7 +568,7 @@ static int via_reinit_one(struct pci_dev *pdev)
 	u32 timing;
 	struct ata_host *host = dev_get_drvdata(&pdev->dev);
 	const struct via_isa_bridge *config = host->private_data;
-	
+
 	via_config_fifo(pdev, config->flags);
 
 	if ((config->flags & VIA_UDMA) == VIA_UDMA_66) {
@@ -583,7 +583,7 @@ static int via_reinit_one(struct pci_dev *pdev)
 		timing &= ~0x80008;
 		pci_write_config_dword(pdev, 0x50, timing);
 	}
-	return ata_pci_device_resume(pdev);	
+	return ata_pci_device_resume(pdev);
 }
 
 static const struct pci_device_id via[] = {
drivers/ata/pata_winbond.c +8 -8
index 3ea345c..cd5560f 100644
@@ -5,7 +5,7 @@
  *    Support for the Winbond 83759A when operating in advanced mode.
  *    Multichip mode is not currently supported.
  */
- 
+
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/pci.h>
@@ -69,7 +69,7 @@ static void winbond_set_piomode(struct ata_port *ap, struct ata_device *adev)
 	int timing = 0x88 + (ap->port_no * 4) + (adev->devno * 2);
 
 	reg = winbond_readcfg(winbond->config, 0x81);
-	
+
 	/* Get the timing data in cycles */
 	if (reg & 0x40)		/* Fast VLB bus, assume 50MHz */
 		ata_timing_compute(adev, adev->pio_mode, &t, 20000, 1000);
@@ -80,9 +80,9 @@ static void winbond_set_piomode(struct ata_port *ap, struct ata_device *adev)
 	recovery = (FIT(t.recover, 1, 15) + 1) & 0x0F;
 	timing = (active << 4) | recovery;
 	winbond_writecfg(winbond->config, timing, reg);
-	
+
 	/* Load the setup timing */
-	
+
 	reg = 0x35;
 	if (adev->class != ATA_DEV_ATA)
 		reg |= 0x08;	/* FIFO off */
@@ -194,13 +194,13 @@ static __init int winbond_init_one(unsigned long port)
 	winbond_writecfg(port, 0x85, reg);
 
 	reg = winbond_readcfg(port, 0x81);
-	
+
 	if (!(reg & 0x03))		/* Disabled */
 		return 0;
 
 	for (i = 0; i < 2 ; i ++) {
 
-		if (reg & (1 << i)) {		
+		if (reg & (1 << i)) {
 			/*
 			 *	Fill in a probe structure first of all
 			 */
@@ -217,7 +217,7 @@ static __init int winbond_init_one(unsigned long port)
 			ae.pio_mask = 0x1F;
 
 			ae.sht = &winbond_sht;
-	
+
 			ae.n_ports = 1;
 			ae.irq = 14 + i;
 			ae.irq_flags = 0;
@@ -257,7 +257,7 @@ static __init int winbond_init(void)
 
 	int ct = 0;
 	int i;
-	
+
 	if (probe_winbond == 0)
 		return -ENODEV;
 
drivers/ata/sata_nv.c +9 -9
index 0d316eb..49f8ff2 100644
@@ -536,7 +536,7 @@ static void nv_adma_mode(struct ata_port *ap)
 
 	if (!(pp->flags & NV_ADMA_PORT_REGISTER_MODE))
 		return;
-		
+
 	WARN_ON(pp->flags & NV_ADMA_ATAPI_SETUP_COMPLETE);
 
 	tmp = readw(mmio + NV_ADMA_CTL);
@@ -576,7 +576,7 @@ static int nv_adma_slave_config(struct scsi_device *sdev)
 		/* Subtract 1 since an extra entry may be needed for padding, see
 		   libata-scsi.c */
 		sg_tablesize = LIBATA_MAX_PRD - 1;
-		
+
 		/* Since the legacy DMA engine is in use, we need to disable ADMA
 		   on the port. */
 		adma_enable = 0;
@@ -588,7 +588,7 @@ static int nv_adma_slave_config(struct scsi_device *sdev)
 		sg_tablesize = NV_ADMA_SGTBL_TOTAL_LEN;
 		adma_enable = 1;
 	}
-	
+
 	pci_read_config_dword(pdev, NV_MCP_SATA_CFG_20, &current_reg);
 
 	if(ap->port_no == 1)
@@ -597,7 +597,7 @@ static int nv_adma_slave_config(struct scsi_device *sdev)
 	else
 		config_mask = NV_MCP_SATA_CFG_20_PORT0_EN |
 			      NV_MCP_SATA_CFG_20_PORT0_PWB_EN;
-	
+
 	if(adma_enable) {
 		new_reg = current_reg | config_mask;
 		pp->flags &= ~NV_ADMA_ATAPI_SETUP_COMPLETE;
@@ -606,10 +606,10 @@ static int nv_adma_slave_config(struct scsi_device *sdev)
 		new_reg = current_reg & ~config_mask;
 		pp->flags |= NV_ADMA_ATAPI_SETUP_COMPLETE;
 	}
-	
+
 	if(current_reg != new_reg)
 		pci_write_config_dword(pdev, NV_MCP_SATA_CFG_20, new_reg);
-	
+
 	blk_queue_bounce_limit(sdev->request_queue, bounce_limit);
 	blk_queue_segment_boundary(sdev->request_queue, segment_boundary);
 	blk_queue_max_hw_segments(sdev->request_queue, sg_tablesize);
@@ -822,13 +822,13 @@ static irqreturn_t nv_adma_interrupt(int irq, void *dev_instance)
 			handled++; /* irq handled if we got here */
 		}
 	}
-	
+
 	if(notifier_clears[0] || notifier_clears[1]) {
 		/* Note: Both notifier clear registers must be written
 		   if either is set, even if one is zero, according to NVIDIA. */
-		writel(notifier_clears[0], 
+		writel(notifier_clears[0],
 			nv_adma_notifier_clear_block(host->ports[0]));
-		writel(notifier_clears[1], 
+		writel(notifier_clears[1],
 			nv_adma_notifier_clear_block(host->ports[1]));
 	}
 
drivers/ata/sata_sis.c +54 -25

164 lines not on this page · raw message

drivers/ata/sata_svw.c +34 -7

88 lines not on this page · raw message

drivers/ata/sata_via.c +1 -1
index 1c7f19a..8c2335c 100644
@@ -319,7 +319,7 @@ static struct ata_probe_ent *vt6420_init_probe_ent(struct pci_dev *pdev)
 {
 	struct ata_probe_ent *probe_ent;
 	struct ata_port_info *ppi[2];
-	
+
 	ppi[0] = ppi[1] = &vt6420_port_info;
 	probe_ent = ata_pci_init_native_mode(pdev, ppi, ATA_PORT_PRIMARY | ATA_PORT_SECONDARY);
 	if (!probe_ent)
include/linux/libata.h +1 -1
index ab27548..9356322 100644
@@ -307,7 +307,7 @@ enum {
 	 * most devices.
 	 */
 	ATA_SPINUP_WAIT		= 8000,
-	
+
 	/* Horkage types. May be set by libata or controller on drives
 	   (some horkage may be drive/controller pair dependant */
 
include/linux/pci_ids.h +1 -0
index 95c1e74..ff9e6d3 100644
@@ -1621,6 +1621,7 @@
 #define PCI_VENDOR_ID_ITE		0x1283
 #define PCI_DEVICE_ID_ITE_8211		0x8211
 #define PCI_DEVICE_ID_ITE_8212		0x8212
+#define PCI_DEVICE_ID_ITE_8213		0x8213
 #define PCI_DEVICE_ID_ITE_8872		0x8872
 #define PCI_DEVICE_ID_ITE_IT8330G_0	0xe886
 
#1 lore raw

drivers/ata/Kconfig config PATA_IT821X · line 308

Quoted 6 lines
drivers/ata/Kconfig +5 -0
+config PATA_IT8213
+	tristate "IT8213 PATA support (Experimental)"
+	depends on PCI && EXPERIMENTAL
+	help
+	  This option enables support for the ITE 821 PATA

Typo (IT8213) - probably my fault but only just noticed it