Add suport for Marvell 88SE6121 in pata_marvell
PATCH 1/1 Add suport for Marvell 88SE6121 in pata_marvell
Marvell 88SE6121 is a ahci controller, but I can't make it work with the achi driver.
This part:
+ else if (pdev->device == 0x6121) {
+ mmio_base = pci_iomap(pdev, 5, 0);
+ if (mmio_base == NULL) {
+ return -ENOMEM;
+ } + /* turn on legacy mode */ + writel(0, mmio_base + 0x04); + (void) readl(mmio_base + 0x04); /* flush */
+ }
put the ahci in legacy mode and work with pata_marvell. Perhaps someone else can make it work whith the ahci driver.
Jose Alberto
drivers/ata/pata_marvell.c +12 -1
@@ -49,7 +49,7 @@ devices =readl (barp +0x0C );pci_iounmap (pdev, barp); -if ((pdev->device ==0x6145 ) && (ap->port_no ==0 ) && +if (((pdev->device ==0x6145 ) || (pdev->device ==0x6121 )) && (ap->port_no ==0 ) && (!(devices &0x10 )))/* PATA enable ? */ return -ENOENT ;
@@ -181,9 +181,19 @@ };struct ata_port_info *port_info[2 ] = { &info, &info_sata };int n_port =2 ; +void __iomem *mmio_base;if (pdev->device ==0x6101 ) n_port =1 ; +else if (pdev->device ==0x6121 ) { + mmio_base =pci_iomap (pdev,5 ,0 ); +if (mmio_base ==NULL ) { +return -ENOMEM ; + } +/* turn on legacy mode */ +writel (0 , mmio_base +0x04 ); + (void )readl (mmio_base +0x04 );/* flush */ + }return ata_pci_init_one (pdev, port_info, n_port); }
@@ -191,6 +201,7 @@static const struct pci_device_id marvell_pci_tbl[] = { {PCI_DEVICE (0x11AB ,0x6101 ), }, {PCI_DEVICE (0x11AB ,0x6145 ), }, + {PCI_DEVICE (0x11AB ,0x6121 ), }, { }/* terminate list */ };
Quoted 1 line · Jose Alberto Reguero
Marvell 88SE6121
[snip]
drivers/ata/pata_marvell.c
Quoted 5 lines
------------------------------------------------------------------------
drivers/ata/pata_marvell.c +0
-0@@ -49,7 +49,7 @@
[snip]
Works-for-me: Jay Cliburn <[email protected]>
The following dmesg snippet after applying the patch shows life from the hitherto unsupported device: (I connected an unpartitioned SATA HDD to it.)
==============
[ 39.789326] PCI: Setting latency timer of device 0000:06:00.0 to 64 [ 39.789436] ata3: PATA max UDMA/100 cmd 0xEC00 ctl 0xE882 bmdma 0xE400 irq 28 [ 39.789541] ata4: PATA max UDMA/133 cmd 0xE800 ctl 0xE482 bmdma 0xE408 irq 28 [ 39.789559] scsi2 : pata_marvell [ 39.790121] BAR5:00:02 01:7F 02:22 03:CA 04:00 05:00 06:00 07:00 08:00 09:00 0A:00 0B:00 0C:07 0D:00 0E:00 0F:00 [ 39.790152] ata3: port disabled. ignoring. [ 39.790154] ata3: reset failed, giving up [ 39.790161] scsi3 : pata_marvell [ 39.790589] BAR5:00:02 01:7F 02:22 03:CA 04:00 05:00 06:00 07:00 08:00 09:00 0A:00 0B:00 0C:07 0D:00 0E:00 0F:00 [ 39.958055] ATA: abnormal status 0x7F on port 0xE807 [ 39.968869] ATA: abnormal status 0x7F on port 0xE807 [ 39.979450] ata4.00: ATA-7, max UDMA/133, 488397168 sectors: LBA48 [ 39.979453] ata4.00: ata4: dev 0 multi count 16 [ 39.987443] ata4.00: configured for UDMA/133 [ 39.987628] scsi 3:0:0:0: Direct-Access ATA WDC WD2500KS-00M 02.0 PQ: 0 ANSI: 5 [ 39.988524] SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB) [ 39.988546] sdb: Write Protect is off [ 39.988548] sdb: Mode Sense: 00 3a 00 00 [ 39.988583] SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 39.988695] SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB) [ 39.988713] sdb: Write Protect is off [ 39.988715] sdb: Mode Sense: 00 3a 00 00 [ 39.988749] SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 39.988781] sdb: unknown partition table [ 39.994867] sd 3:0:0:0: Attached scsi disk sdb [ 39.994990] sd 3:0:0:0: Attached scsi generic sg1 type 0
This is the relevant portion of lspci:
==============
06:00.0 SATA controller: Marvell Technology Group Ltd. Unknown device 6121 (rev b0) (prog-if 8f)
Subsystem: ASUSTeK Computer Inc. Unknown device 8212
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 28
Region 0: I/O ports at ec00 [size=8]
Region 1: I/O ports at e880 [size=4]
Region 2: I/O ports at e800 [size=8]
Region 3: I/O ports at e480 [size=4]
Region 4: I/O ports at e400 [size=16]
Region 5: Memory at fbeffc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mAPME(D0+,D1+,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Message Signalled Interrupts: 64bit-
Queue=0/0 Enable
-
Address: 00000000 Data: 0000
Capabilities: [e0] Express Legacy Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0,
ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr+ NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s, Port 1
Link: Latency L0s <256ns, L1 unlimited
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
00: ab 11 21 61 07 01 10 00 b0 8f 06 01 10 00 00 00
10: 01 ec 00 00 81 e8 00 00 01 e8 00 00 81 e4 00 00
20: 01 e4 00 00 00 fc ef fb 00 00 00 00 43 10 12 82
30: 00 00 00 00 48 00 00 00 00 00 00 00 0b 01 00 00
40: 24 c9 c0 00 1f 80 00 00 01 50 02 5a 00 20 00 13
50: 05 e0 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 58 c4 21 40 b0 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 10 00 11 00 c0 0f 18 00 00 24 08 00 11 a4 03 01
f0: 00 00 11 10 00 00 00 00 00 00 00 00 00 00 00 00