SATA/IDE Dual Mode w/Intel 945 Chipset or HOW TO LIQUIFY a flash IDE chip under 2.6.18
I just finished pulling out a melted IDE flash drive out of a Shuttle motherboard with the intel 945 chipset which claims to support SATA and IDE drives concurrently under Linux 2.6.18.
The chip worked for about 30 seconds before liquifying in the chassis. I note that the 945 chipset in the shuttle PC had some serious
issues recognizing 2 x SATA devices and a IDE device concurrently. Are there known problems with the Linux drivers
with these newer chipsets.
One other disturbing issue was the IDE flash drive was configured (and recognized) as /dev/hda during bootup, but when it got to the root mountint, even with root=/dev/hda set, it still kept thinking the drive was at scsi (ATA) device (08,13) and kept crashing with VFS cannot find root FS errors.
Jeff
Jeff V. Merkey wrote:
root=/dev/hda2 is what was passed to the kernel from grub.
Jeff
Quoted 19 lines
I just finished pulling out a melted IDE flash drive out of a Shuttle motherboard with the intel 945 chipset which claims to support SATA and IDE drives concurrently under Linux 2.6.18.
The chip worked for about 30 seconds before liquifying in the chassis. I note that the 945 chipset in the shuttle PC had some serious
issues recognizing 2 x SATA devices and a IDE device concurrently. Are there known problems with the Linux drivers
with these newer chipsets.One other disturbing issue was the IDE flash drive was configured (and recognized) as
/dev/hdaduring bootup, but when it got to the root mountint, even with root=/dev/hda set, it still kept thinking the drive was at scsi (ATA) device (08,13) and kept crashing with VFS cannot find root FS errors.Jeff
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Quoted 17 lines · Jeff V. Merkey
Jeff V. Merkey wrote:
root=/dev/hda2 is what was passed to the kernel from grub.
Jeff
Quoted 11 lines
I just finished pulling out a melted IDE flash drive out of a Shuttle motherboard with the intel 945 chipset which claims to support SATA and IDE drives concurrently under Linux 2.6.18.
The chip worked for about 30 seconds before liquifying in the chassis. I note that the 945 chipset in the shuttle PC had some serious
issues recognizing 2 x SATA devices and a IDE device concurrently. Are there known problems with the Linux drivers
with these newer chipsets.One other disturbing issue was the IDE flash drive was configured (and recognized) as
/dev/hdaduring bootup, but when it got to the root mountint, even with root=/dev/hda set, it still kept thinking the drive was at scsi (ATA) device (08,13) and kept crashing with VFS cannot find root FS errors.
it sounds like someone switched the BIOS IDE setting from ide-compatible/legacy to AHCI or similar, a not uncommon option in the sata controllers on those boards.
None of that would explain the melting of anything of course.
Cheers,
Auke
Quoted 16 lines · Auke Kok
Quoted 14 lines · Jeff V. Merkey
Jeff V. Merkey wrote:
root=/dev/hda2 is what was passed to the kernel from grub.
Jeff
Quoted 8 lines
I just finished pulling out a melted IDE flash drive out of a Shuttle motherboard with the intel 945 chipset which claims to support SATA and IDE drives concurrently under Linux 2.6.18.
The chip worked for about 30 seconds before liquifying in the chassis. I note that the 945 chipset in the shuttle PC had some serious
issues recognizing 2 x SATA devices and a IDE device concurrently. Are there known problems with the Linux drivers
with these newer chipsets.
Quoted 8 lines
Quoted 4 lines
Quoted 3 lines
One other disturbing issue was the IDE flash drive was configured (and recognized) as
/dev/hdaduring bootup, but when it got to the root mountint, even with root=/dev/hda set, it still kept thinking the drive was at scsi (ATA) device (08,13) and kept crashing with VFS cannot find root FS errors.it sounds like someone switched the BIOS IDE setting from ide-compatible/legacy to AHCI or similar, a not uncommon option in the sata controllers on those boards.
None of that would explain the melting of anything of course.
Would be if pin 20 were powered for some reason (which it should NOT be).
Jeff
Quoted 10 lines
Cheers,
Auke
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Quoted 9 lines · Jeff V. Merkey
I just finished pulling out a melted IDE flash drive out of a Shuttle motherboard with the intel 945 chipset which claims to support SATA and IDE drives concurrently under Linux 2.6.18.
The chip worked for about 30 seconds before liquifying in the chassis. I note that the 945 chipset in the shuttle PC had some serious
issues recognizing 2 x SATA devices and a IDE device concurrently. Are
there known problems with the Linux drivers
with these newer chipsets.
Had the drive ever been used in any other machine? Had any ide device ever been used in this machine before? It really sounds like a hardware problem, since I can't think of anything software could do to make that kind of current go through the flash drive.
I remember seeing the controller chip on a 730MB quantum scsi drive start to glow red many years ago, just before the drive stopped responding to the system (and I turned off the power). Hardware does fail. It almost never has anything to do with software.
--
Len Sorensen
Quoted 6 lines · Lennart Sorensen
Quoted 3 lines · Jeff V. Merkey
I just finished pulling out a melted IDE flash drive out of a Shuttle motherboard with the intel 945 chipset which claims to support SATA and IDE drives concurrently under Linux 2.6.18.
Quoted 8 lines
Quoted 5 lines
The chip worked for about 30 seconds before liquifying in the chassis. I note that the 945 chipset in the shuttle PC had some serious
issues recognizing 2 x SATA devices and a IDE device concurrently. Are there known problems with the Linux drivers
with these newer chipsets.Had the drive ever been used in any other machine?
Yes, on a SuperMicro X6DHE-G2 Xeon motherboard -- worked fine.
Quoted 3 lines
Had any ide device
ever been used in this machine before?
Yes. external cabled CDROM Drive seems to work.
Jeff
Quoted 19 lines
It really sounds like a hardware
problem, since I can't think of anything software could do to make that kind of current go through the flash drive.I remember seeing the controller chip on a 730MB quantum scsi drive start to glow red many years ago, just before the drive stopped responding to the system (and I turned off the power). Hardware does fail. It almost never has anything to do with software.
--
Len Sorensen
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Quoted 11 lines · Jeff V. Merkey
I just finished pulling out a melted IDE flash drive out of a Shuttle motherboard with the intel 945 chipset which claims to support SATA and IDE drives concurrently under Linux 2.6.18.
The chip worked for about 30 seconds before liquifying in the chassis. I note that the 945 chipset in the shuttle PC had some serious
issues recognizing 2 x SATA devices and a IDE device concurrently. Are there known problems with the Linux drivers
with these newer chipsets.One other disturbing issue was the IDE flash drive was configured (and recognized) as
/dev/hdaduring bootup, but when it got to the root mountint, even with root=/dev/hda set, it still kept thinking the drive was at scsi (ATA) device (08,13) and kept crashing with VFS cannot find root FS errors.
We have two sets of ATA drivers now, and Intel motherboards support bazillion annoying IDE modes, so you will need to provide more info than this.
Is the motherboard in combined mode? native mode? AHCI or RAID mode?
What driver set did you pick? is drivers/ide built in, modular, or disabled? is drivers/ata built in, modular, or disabled?
The cannot-find-root-FS errors are definitely caused by driver and/or initrd misconfiguration. The melted flash, I dunno, maybe you managed to get two drivers fighting over the same hardware.
Jeff
Quoted 10 lines · Jeff Garzik
Quoted 8 lines · Jeff V. Merkey
I just finished pulling out a melted IDE flash drive out of a Shuttle motherboard with the intel 945 chipset which claims to support SATA and IDE drives concurrently under Linux 2.6.18.
The chip worked for about 30 seconds before liquifying in the chassis. I note that the 945 chipset in the shuttle PC had some serious
issues recognizing 2 x SATA devices and a IDE device concurrently. Are there known problems with the Linux drivers
with these newer chipsets.
Quoted 8 lines
Quoted 3 lines
One other disturbing issue was the IDE flash drive was configured (and recognized) as
/dev/hdaduring bootup, but when it got to the root mountint, even with root=/dev/hda set, it still kept thinking the drive was at scsi (ATA) device (08,13) and kept crashing with VFS cannot find root FS errors.We have two sets of ATA drivers now, and Intel motherboards support bazillion annoying IDE modes, so you will need to provide more info than this.
Is the motherboard in combined mode?
Yes. "Enhanced mode" is how it is listed in the BIOS.
Quoted 1 line
native mode? AHCI or RAID mode?
No RAID, just enhanced mode (SATA 3.0 + IDE)
Quoted 1 line
What driver set did you pick?
Standard build = standard IDE + Intel PIIX + SATA + Intel ICP
Quoted 1 line
is
drivers/idebuilt in, modular, or disabled? isdrivers/atabuilt in, modular, or disabled?
built in in all cases.
Quoted 2 lines
The cannot-find-root-FS errors are definitely caused by driver and/or initrd misconfiguration. The melted flash, I dunno, maybe you managed to get two drivers fighting over the same hardware.
No. Seems related to the chipset problems. If I say "root=/dev/hda2" I have better not be getting errors claiming device 08:13 could not mount as root. memory corruption?
The melted flash seems power related (like pin 20 was live for some reason on a standard IDE).
Jeff
Quoted 6 lines
Jeff
Quoted 17 lines · Jeff V. Merkey
Quoted 15 lines · Jeff Garzik
Quoted 11 lines · Jeff V. Merkey
I just finished pulling out a melted IDE flash drive out of a Shuttle motherboard with the intel 945 chipset which claims to support SATA and IDE drives concurrently under Linux 2.6.18.
The chip worked for about 30 seconds before liquifying in the chassis. I note that the 945 chipset in the shuttle PC had some serious
issues recognizing 2 x SATA devices and a IDE device concurrently. Are there known problems with the Linux drivers
with these newer chipsets.One other disturbing issue was the IDE flash drive was configured (and recognized) as
/dev/hdaduring bootup, but when it got to the root mountint, even with root=/dev/hda set, it still kept thinking the drive was at scsi (ATA) device (08,13) and kept crashing with VFS cannot find root FS errors.
Quoted 6 lines
Quoted 3 lines
We have two sets of ATA drivers now, and Intel motherboards support bazillion annoying IDE modes, so you will need to provide more info than this.
Is the motherboard in combined mode?
Yes. "Enhanced mode" is how it is listed in the BIOS.
Combined mode is a technical term. Judging from your answers, you are not using combined mode.
Quoted 3 lines
Quoted 1 line
native mode? AHCI or RAID mode?
No RAID, just enhanced mode (SATA 3.0 + IDE)
Judging from your answers, you are not in AHCI mode.
Side note: You should use AHCI if available. Emulating a PATA interface for SATA devices is error prone [in the silicon]. AHCI is native SATA, "enhanced mode" is not.
Quoted 3 lines
Quoted 1 line
The cannot-find-root-FS errors are definitely caused by driver and/or initrd misconfiguration. The melted flash, I dunno, maybe you managed to get two drivers fighting over the same hardware.
No. Seems related to the chipset problems. If I say "root=/dev/hda2" I have better not be getting errors claiming device 08:13 could not mount as root. memory corruption?
If the kernel cannot mount the requested root= disk, it tries the default that is encoded into the vmlinuz image at build time, which is probably 08:13.
Quoted 1 line
The melted flash seems power related (like pin 20 was live for some reason on a standard IDE).
Probably, otherwise we would have many more reports like this than just yours.
Jeff
Quoted 35 lines · Jeff Garzik
Quoted 18 lines · Jeff V. Merkey
Quoted 16 lines · Jeff Garzik
Quoted 11 lines · Jeff V. Merkey
I just finished pulling out a melted IDE flash drive out of a Shuttle motherboard with the intel 945 chipset which claims to support SATA and IDE drives concurrently under Linux 2.6.18.
The chip worked for about 30 seconds before liquifying in the chassis. I note that the 945 chipset in the shuttle PC had some serious
issues recognizing 2 x SATA devices and a IDE device concurrently. Are there known problems with the Linux drivers
with these newer chipsets.One other disturbing issue was the IDE flash drive was configured (and recognized) as
/dev/hdaduring bootup, but when it got to the root mountint, even with root=/dev/hda set, it still kept thinking the drive was at scsi (ATA) device (08,13) and kept crashing with VFS cannot find root FS errors.Quoted 7 lines
Quoted 3 lines
We have two sets of ATA drivers now, and Intel motherboards support bazillion annoying IDE modes, so you will need to provide more info than this.
Is the motherboard in combined mode?
Yes. "Enhanced mode" is how it is listed in the BIOS.
Combined mode is a technical term. Judging from your answers, you are not using combined mode.
Quoted 3 lines
Quoted 1 line
native mode? AHCI or RAID mode?
Quoted 6 lines
Quoted 1 line
No RAID, just enhanced mode (SATA 3.0 + IDE)
Judging from your answers, you are not in AHCI mode.
Side note: You should use AHCI if available. Emulating a PATA interface for SATA devices is error prone [in the silicon]. AHCI is native SATA, "enhanced mode" is not.
AHCI It is.
Jeff
Quoted 20 lines
Quoted 6 lines
Quoted 3 lines
The cannot-find-root-FS errors are definitely caused by driver and/or initrd misconfiguration. The melted flash, I dunno, maybe you managed to get two drivers fighting over the same hardware.
No. Seems related to the chipset problems. If I say "root=/dev/hda2" I have better not be getting errors claiming device 08:13 could not mount as root. memory corruption?
If the kernel cannot mount the requested root= disk, it tries the default that is encoded into the vmlinuz image at build time, which is probably 08:13.
Quoted 1 line
The melted flash seems power related (like pin 20 was live for some reason on a standard IDE).
Probably, otherwise we would have many more reports like this than just yours.
Jeff
Quoted 2 lines · Jeff Garzik
Combined mode is a technical term. Judging from your answers, you are not using combined mode.
I would have thought 'sata 3.0 + IDE' sounded a lot like combined mode, unless it means seperate sata and ide.
Quoted 5 lines
Judging from your answers, you are not in AHCI mode.
Side note: You should use AHCI if available. Emulating a PATA interface for SATA devices is error prone [in the silicon]. AHCI is native SATA, "enhanced mode" is not.
I tried setting my sister's new machine to AHCI mode (Asus P5B with 965 chipset), but I eventually gave up since it also needed windows xp on it and I can't for the life of me find an AHCI driver for windows that would install.
--
Len Sorensen
Quoted 5 lines · Lennart Sorensen
Quoted 1 line · Jeff Garzik
Combined mode is a technical term. Judging from your answers, you are not using combined mode.
I would have thought 'sata 3.0 + IDE' sounded a lot like combined mode, unless it means seperate sata and ide.
Enhanced mode means separate SATA and PATA.
(I recommend avoiding the "IDE" acronym, it is largely meaningless and confusing these days)
Quoted 8 lines
Quoted 3 lines
Judging from your answers, you are not in AHCI mode.
Side note: You should use AHCI if available. Emulating a PATA interface for SATA devices is error prone [in the silicon]. AHCI is native SATA, "enhanced mode" is not.
I tried setting my sister's new machine to AHCI mode (Asus P5B with 965 chipset), but I eventually gave up since it also needed windows xp on it and I can't for the life of me find an AHCI driver for windows that would install.
Um, ok?
We're talking about Linux here. Linux regularly supports hardware before Windows does. This is nothing new.
Jeff
Quoted 4 lines · Jeff Garzik
Enhanced mode means separate SATA and PATA.
(I recommend avoiding the "IDE" acronym, it is largely meaningless and confusing these days)
Good idea.
Quoted 2 lines
We're talking about Linux here. Linux regularly supports hardware before Windows does. This is nothing new.
That is certainly true. I just found it odd that intel wouldn't have an ahci driver available. But then again if ahci is standard I guess they would expect microsoft to provide the driver instead, which they probably aren't doing until vista. Linux always seems so much easier. :) The drivers are just included for everything.
--
Len Sorensen
Am Mittwoch 10 Januar 2007 15:39 schrieb Lennart Sorensen:
Quoted 4 lines
I tried setting my sister's new machine to AHCI mode (Asus P5B with 965 chipset), but I eventually gave up since it also needed windows xp on it and I can't for the life of me find an AHCI driver for windows that would install.
You can install the Intel Matrix driver after "adjusting" the inf file...
Signature · 3 lines
(°= =°) //\ Prakash Punnoor /\\ V_/ \_V
Quoted 1 line · Prakash Punnoor
You can install the Intel Matrix driver after "adjusting" the inf file...
Hmm, I guess a good question is: Why should I have to edit the inf file? Is it an issue of them making it only install if your hardware is already set to ahci mode? But how am I supposed to boot and install the driver until I have the driver installed then. Well I might try that next time I go there. How stupid of intel.
--
Len Sorensen
Quoted 7 lines · Lennart Sorensen
Quoted 3 lines · Prakash Punnoor
You can install the Intel Matrix driver after "adjusting" the inf file...
Quoted 10 lines
Hmm, I guess a good question is: Why should I have to edit the inf file? Is it an issue of them making it only install if your hardware is already set to ahci mode? But how am I supposed to boot and install the driver until I have the driver installed then. Well I might try that next time I go there.
How stupid of intel.
No doubt part of the Wintel (intel + Microsoft) strategy to perpetually break non-windows platforms with new incompatible hardware like the switch over from the e1000 MT adapters to e1000 GT which are not backward compatible with the older chipsets.
I still have not seen the GT adapter work correctly off windows.
Jeff
:-)
Jeff
Quoted 5 lines
--
Len Sorensen
Quoted 6 lines · Jeff V. Merkey
No doubt part of the Wintel (intel + Microsoft) strategy to perpetually break non-windows platforms with new incompatible
hardware like the switch over from the e1000 MT adapters to e1000 GT which are not backward compatible with the older chipsets.I still have not seen the GT adapter work correctly off windows.
But isn't AHCI a new standard intel helped develop? Why would they want to make it hard to use intel hardware using a standard interface intel helped create? It makes no sense. Linux doesn't care if the sata is set to the old PATA compatible interface, or the new AHCI mode. Windows simply can't boot in AHCI mode and refuses to install a driver for AHCI mode when it is not already in AHCI mode.
--
Len Sorensen
Quoted 2 lines · Jeff V. Merkey
No doubt part of the Wintel (intel + Microsoft) strategy to perpetually break non-windows platforms with new incompatible hardware like the switch over from the e1000 MT adapters to e1000 GT which are not backward compatible with the older chipsets.
I presume you mean breaking /windows/ platforms?
As I noted, Linux often supports the hardware from the "big" hardware vendors before Windows does.
They use Linux as a "rabbit" to push Microsoft into supporting something, with the "Linux supports it already" argument.
Jeff
Am Mittwoch 10 Januar 2007 18:47 schrieb Lennart Sorensen:
Quoted 8 lines · Prakash Punnoor
Quoted 1 line
You can install the Intel Matrix driver after "adjusting" the inf file...
Hmm, I guess a good question is: Why should I have to edit the inf file? Is it an issue of them making it only install if your hardware is already set to ahci mode? But how am I supposed to boot and install the driver until I have the driver installed then. Well I might try that next time I go there. How stupid of intel.
Intel wants you to buy hw with ICH8R. ICH8 isn't get the advanced features for free....
To get the driver going: Put your hd to the jmicron, install driver, put hd back to ich8...
Signature · 3 lines
(°= =°) //\ Prakash Punnoor /\\ V_/ \_V
Quoted 2 lines · Prakash Punnoor
Intel wants you to buy hw with ICH8R. ICH8 isn't get the advanced features for free....
But the BIOS has AHCI mode as an option. I don't want their fake raid, just ahci. That isn't an advanced feature, it is native mode. :)
Quoted 2 lines
To get the driver going: Put your hd to the jmicron, install driver, put hd back to ich8...
Hmm, could try that, assuming the jmicron controller doesn't mind. Of course the jmicron can also be set to ahci mode (not that I have an ahci driver for it either under windows).
--
Len Sorensen
Quoted 10 lines · Prakash Punnoor
Am Mittwoch 10 Januar 2007 18:47 schrieb Lennart Sorensen:
Quoted 7 lines · Prakash Punnoor
Quoted 1 line
You can install the Intel Matrix driver after "adjusting" the inf file...
Hmm, I guess a good question is: Why should I have to edit the inf file? Is it an issue of them making it only install if your hardware is already set to ahci mode? But how am I supposed to boot and install the driver until I have the driver installed then. Well I might try that next time I go there. How stupid of intel.
Intel wants you to buy hw with ICH8R. ICH8 isn't get the advanced features for free....
What advanced features do you claim are missing from ICH8?
The 'R' indicates software RAID, provided by BIOS and a software driver.
Which uses the standard AHCI programming interface. ICH8 provides
AHCI, just like ICH8R does.
Jeff
Am Mittwoch 10 Januar 2007 19:19 schrieb Jeff Garzik:
Quoted 5 lines
Quoted 2 lines · Prakash Punnoor
Intel wants you to buy hw with ICH8R. ICH8 isn't get the advanced features for free....
What advanced features do you claim are missing from ICH8?
I don't claim anything. Intel does. I know that the chip is basically the same.
Quoted 3 lines
The 'R' indicates software RAID, provided by BIOS and a software driver.
Which uses the standard AHCI programming interface. ICH8 provides
AHCI, just like ICH8R does.
Yes, I know...
Signature · 3 lines
(°= =°) //\ Prakash Punnoor /\\ V_/ \_V