exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen with pata_amd
Hi,
I tried a cat /dev/sdb1 >/dev/null from a Sandisk Extreme III CF card connected via cf to IDE adapteer to onboard ide of nforce c51. I am usinf 2.6.20 on x86_64. For a few seconds it worked but then it dropped to pio4:
ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen ata3.00: (BMDMA stat 0x65)
ata3.00: cmd c8/00:80:1f:7d:01/00:00:00:00:00/e0 tag 0 cdb 0x0 data 65536 in
res 58/00:00:9e:7d:01/00:00:00:00:00/e0 Emask 0x2 (HSM violation)
ata3: soft resetting port
ata3.00: simplex DMA is claimed by other device, disabling DMA ata3.00: configured for PIO4
ata3: EH complete
SCSI device sdb: 2001888 512-byte hdwr sectors (1025 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
While boot I get:sata_nv 0000:00:0e.0: version 3.2
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [APSI] -> GSI 22 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:0e.0 to 64
ata1: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xE000 irq 22
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xE008 irq 22 scsi0 : sata_nv
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-7, max UDMA/133, 586114704 sectors: LBA48 NCQ (depth 0/32) ata1.00: ata1: dev 0 multi count 1
ata1.00: configured for UDMA/133
scsi1 : sata_nv
ata2: SATA link down (SStatus 0 SControl 300)
ATA: abnormal status 0x7F on port 0x977
scsi 0:0:0:0: Direct-Access ATA Maxtor 7V300F0 VA11 PQ: 0 ANSI: 5
SCSI device sda: 586114704 512-byte hdwr sectors (300091 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sda: 586114704 512-byte hdwr sectors (300091 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 < sda5 sda6 sda7 sda8 > sda3
sd 0:0:0:0: Attached scsi disk sda
sd 0:0:0:0: Attached scsi generic sg0 type 0pata_amd 0000:00:0d.0: version 0.2.7
PCI: Setting latency timer of device 0000:00:0d.0 to 64
ata3: PATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0xF400 irq 14
ata4: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xF408 irq 15 scsi2 : pata_amd
ata3.00: CFA, max MWDMA2, 2001888 sectors: LBA
ata3.00: ata3: dev 0 multi count 0
ata3.00: configured for MWDMA2
scsi3 : pata_amd
ata4: port disabled. ignoring.
ata4: reset failed, giving up
scsi 2:0:0:0: Direct-Access ATA SanDisk SDCFX-10 HDX PQ: 0 ANSI: 5
SCSI device sdb: 2001888 512-byte hdwr sectors (1025 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sdb: 2001888 512-byte hdwr sectors (1025 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1
sd 2:0:0:0: Attached scsi removable disk sdb
sd 2:0:0:0: Attached scsi generic sg1 type 0
Signature · 3 lines
(°= =°) //\ Prakash Punnoor /\\ V_/ \_V
Am Samstag 17 Februar 2007 schrieb Prakash Punnoor:
Quoted 68 lines
Hi,
I tried a cat
/dev/sdb1>/dev/null from a Sandisk Extreme III CF card connected via cf to IDE adapteer to onboard ide of nforce c51. I am usinf 2.6.20 onx86_64. For a few seconds it worked but then it dropped to pio4:ata3.00: exception Emask
0x0SAct0x0SErr0x0action0x2frozen ata3.00: (BMDMA stat0x65)
ata3.00: cmd c8/00:80:1f:7d:01/00:00:00:00:00/e0 tag 0 cdb0x0data 65536 in res 58/00:00:9e:7d:01/00:00:00:00:00/e0 Emask0x2(HSM violation) ata3:
soft resetting port
ata3.00: simplex DMA is claimed by other device, disabling DMA ata3.00: configured for PIO4
ata3: EH complete
SCSI device sdb: 2001888 512-byte hdwr sectors (1025 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUAWhile boot I get:
sata_nv0000:00:0e.0: version 3.2
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [APSI] -> GSI 22 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:0e.0 to 64
ata1: SATA max UDMA/133 cmd0x9F0ctl0xBF2bmdma0xE000irq 22
ata2: SATA max UDMA/133 cmd0x970ctl0xB72bmdma0xE008irq 22 scsi0 :sata_nv
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-7, max UDMA/133, 586114704 sectors: LBA48 NCQ (depth 0/32) ata1.00: ata1: dev 0 multi count 1
ata1.00: configured for UDMA/133
scsi1 :sata_nv
ata2: SATA link down (SStatus 0 SControl 300)
ATA: abnormal status0x7Fon port0x977
scsi 0:0:0:0: Direct-Access ATA Maxtor 7V300F0 VA11 PQ: 0 ANSI:
5 SCSI device sda: 586114704 512-byte hdwr sectors (300091 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sda: 586114704 512-byte hdwr sectors (300091 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 < sda5 sda6 sda7 sda8 > sda3
sd 0:0:0:0: Attached scsi disk sda
sd 0:0:0:0: Attached scsi generic sg0 type 0pata_amd0000:00:0d.0: version 0.2.7
PCI: Setting latency timer of device 0000:00:0d.0 to 64
ata3: PATA max UDMA/133 cmd0x1F0ctl0x3F6bmdma0xF400irq 14
ata4: PATA max UDMA/133 cmd0x170ctl0x376bmdma0xF408irq 15 scsi2 :pata_amd
ata3.00: CFA, max MWDMA2, 2001888 sectors: LBA
ata3.00: ata3: dev 0 multi count 0
ata3.00: configured for MWDMA2
scsi3 :pata_amd
ata4: port disabled. ignoring.
ata4: reset failed, giving up
scsi 2:0:0:0: Direct-Access ATA SanDisk SDCFX-10 HDX PQ: 0 ANSI:
5 SCSI device sdb: 2001888 512-byte hdwr sectors (1025 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Quoted 8 lines
SCSI device sdb: 2001888 512-byte hdwr sectors (1025 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1
sd 2:0:0:0: Attached scsi removable disk sdb
sd 2:0:0:0: Attached scsi generic sg1 type 0
The ide driver worked better - for a short time and then this happens:
hda: dma_intr: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: DMA disabled
Any idea?
Signature · 3 lines
(°= =°) //\ Prakash Punnoor /\\ V_/ \_V
Am Samstag 17 Februar 2007 schrieb Prakash Punnoor:
Quoted 22 lines
Am Samstag 17 Februar 2007 schrieb Prakash Punnoor:
Quoted 21 lines
Hi,
I tried a cat
/dev/sdb1>/dev/null from a Sandisk Extreme III CF card connected via cf to IDE adapteer to onboard ide of nforce c51. I am usinf 2.6.20 onx86_64. For a few seconds it worked but then it dropped to pio4:ata3.00: exception Emask
0x0SAct0x0SErr0x0action0x2frozen ata3.00: (BMDMA stat0x65)
ata3.00: cmd c8/00:80:1f:7d:01/00:00:00:00:00/e0 tag 0 cdb0x0data 65536 in res 58/00:00:9e:7d:01/00:00:00:00:00/e0 Emask0x2(HSM violation)
ata3: soft resetting port
ata3.00: simplex DMA is claimed by other device, disabling DMA ata3.00: configured for PIO4
ata3: EH complete
SCSI device sdb: 2001888 512-byte hdwr sectors (1025 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[...]
Quoted 6 lines
The ide driver worked better - for a short time and then this happens:
hda:
dma_intr: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: DMA disabled
I connected the cf to ide adapter to an ide to sata adapter and using this combination on sata_nv makes no troubkes whatsoever. So what goues wrong with pata_amd/amd ide driver? BTW, I found specs for the cf card on the sandisk website. Perhaps someone wants to check whether the amd drivers deal corretcly with the true ide mode implemented in the cf card?
http://www.sandisk.com/Assets/File/OEM/Manuals/ProdManCFlashv11.0.pdf
scsi 1:0:0:0: Direct-Access ATA SanDisk SDCFX-10 HDX PQ: 0 ANSI: 5
SCSI device sdb: 2001888 512-byte hdwr sectors (1025 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sdb: 2001888 512-byte hdwr sectors (1025 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1
sd 1:0:0:0: Attached scsi removable disk sdb
sd 1:0:0:0: Attached scsi generic sg1 type 0
Signature · 3 lines
(°= =°) //\ Prakash Punnoor /\\ V_/ \_V
Am Sonntag 18 Februar 2007 schrieb Prakash Punnoor:
Quoted 31 lines
Am Samstag 17 Februar 2007 schrieb Prakash Punnoor:
Quoted 21 lines
Am Samstag 17 Februar 2007 schrieb Prakash Punnoor:
Quoted 20 lines
Hi,
I tried a cat
/dev/sdb1>/dev/null from a Sandisk Extreme III CF card connected via cf to IDE adapteer to onboard ide of nforce c51. I am usinf 2.6.20 onx86_64. For a few seconds it worked but then it dropped to pio4:ata3.00: exception Emask
0x0SAct0x0SErr0x0action0x2frozen ata3.00: (BMDMA stat0x65)
ata3.00: cmd c8/00:80:1f:7d:01/00:00:00:00:00/e0 tag 0 cdb0x0data 65536 in res 58/00:00:9e:7d:01/00:00:00:00:00/e0 Emask0x2(HSM violation) ata3: soft resetting port
ata3.00: simplex DMA is claimed by other device, disabling DMA ata3.00: configured for PIO4
ata3: EH complete
SCSI device sdb: 2001888 512-byte hdwr sectors (1025 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA[...]
Quoted 5 lines
The ide driver worked better - for a short time and then this happens:
hda:
dma_intr: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hda: DMA disabled
Quoted 7 lines
I connected the cf to ide adapter to an ide to sata adapter and using this combination on
sata_nvmakes no troubkes whatsoever. So what goues wrong with pata_amd/amd ide driver? BTW, I found specs for the cf card on the sandisk website. Perhaps someone wants to check whether the amd drivers deal corretcly with the true ide mode implemented in the cf card?http://www.sandisk.com/Assets/File/OEM/Manuals/ProdManCFlashv11.0.pdf
For what it's worth: I tried the cd-ide adapter with the sandisk cf on another machine with ide uli/ali driver and here I don't have any problems as well. So everything points to amd driver...
Signature · 3 lines
(°= =°) //\ Prakash Punnoor /\\ V_/ \_V