Skip to contentSkip to conversation

skge: fix transmitter flow control

PATCH Applied Stephen Hemminger 2 participants 3 messages Feb 23, 2007 – Feb 27, 2007

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/2 skge: fix transmitter flow control

It looks like the skge driver inherited another bug from the sk98lin code. If I send from 1000mbit port to a machine on 100mbit port, the switch should be doing hardware flow control, but no pause frames show up in the statistics.

This is the analog of the recent sky2 fixes. The device needs to listen for multicast pause frames and then not discard them.

---
 drivers/net/skge.c |   43 ++++++++++++++++++++++++++++++++-----------
 drivers/net/skge.h |    3 +--
 2 files changed, 33 insertions(+), 13 deletions(-)
drivers/net/skge.c +32 -11
@@ -2767,6 +2767,17 @@
 	return err;
 }
 
+static const u8 pause_mc_addr[ETH_ALEN] = { 0x1, 0x80, 0xc2, 0x0, 0x0, 0x1 };
+
+static void genesis_add_filter(u8 filter[8], const u8 *addr)
+{
+	u32 crc, bit;
+
+	crc = ether_crc_le(ETH_ALEN, addr);
+	bit = ~crc & 0x3f;
+	filter[bit/8] |= 1 << (bit%8);
+}
+
 static void genesis_set_multicast(struct net_device *dev)
 {
 	struct skge_port *skge = netdev_priv(dev);
@@ -2788,24 +2799,33 @@
 		memset(filter, 0xff, sizeof(filter));
 	else {
 		memset(filter, 0, sizeof(filter));
-		for (i = 0; list && i < count; i++, list = list->next) {
-			u32 crc, bit;
-			crc = ether_crc_le(ETH_ALEN, list->dmi_addr);
-			bit = ~crc & 0x3f;
-			filter[bit/8] |= 1 << (bit%8);
-		}
+
+		if (skge->flow_status == FLOW_STAT_REM_SEND
+		    || skge->flow_status == FLOW_STAT_SYMMETRIC)
+			genesis_add_filter(filter, pause_mc_addr);
+
+		for (i = 0; list && i < count; i++, list = list->next)
+			genesis_add_filter(filter, list->dmi_addr);
 	}
 
 	xm_write32(hw, port, XM_MODE, mode);
 	xm_outhash(hw, port, XM_HSM, filter);
 }
 
+static void yukon_add_filter(u8 filter[8], const u8 *addr)
+{
+	 u32 bit = ether_crc(ETH_ALEN, addr) & 0x3f;
+	 filter[bit/8] |= 1 << (bit%8);
+}
+
 static void yukon_set_multicast(struct net_device *dev)
 {
 	struct skge_port *skge = netdev_priv(dev);
 	struct skge_hw *hw = skge->hw;
 	int port = skge->port;
 	struct dev_mc_list *list = dev->mc_list;
+	int rx_pause = (skge->flow_status == FLOW_STAT_REM_SEND
+			|| skge->flow_status == FLOW_STAT_SYMMETRIC);
 	u16 reg;
 	u8 filter[8];
 
@@ -2818,16 +2838,17 @@
 		reg &= ~(GM_RXCR_UCF_ENA | GM_RXCR_MCF_ENA);
 	else if (dev->flags & IFF_ALLMULTI)	/* all multicast */
 		memset(filter, 0xff, sizeof(filter));
-	else if (dev->mc_count == 0)		/* no multicast */
+	else if (dev->mc_count == 0 && !rx_pause)/* no multicast */
 		reg &= ~GM_RXCR_MCF_ENA;
 	else {
 		int i;
 		reg |= GM_RXCR_MCF_ENA;
 
-		for (i = 0; list && i < dev->mc_count; i++, list = list->next) {
-			u32 bit = ether_crc(ETH_ALEN, list->dmi_addr) & 0x3f;
-			filter[bit/8] |= 1 << (bit%8);
-		}
+		if (rx_pause)
+			yukon_add_filter(filter, pause_mc_addr);
+
+		for (i = 0; list && i < dev->mc_count; i++, list = list->next)
+			yukon_add_filter(filter, list->dmi_addr);
 	}
 
 
drivers/net/skge.h +1 -2
@@ -1849,8 +1849,7 @@
 			  GMR_FS_JABBER,
 /* Rx GMAC FIFO Flush Mask (default) */
 	RX_FF_FL_DEF_MSK = GMR_FS_CRC_ERR | GMR_FS_RX_FF_OV |GMR_FS_MII_ERR |
-			   GMR_FS_BAD_FC | GMR_FS_GOOD_FC | GMR_FS_UN_SIZE |
-			   GMR_FS_JABBER,
+			   GMR_FS_BAD_FC |  GMR_FS_UN_SIZE | GMR_FS_JABBER,
 };
 
 /*	RX_GMF_CTRL_T	32 bit	Rx GMAC FIFO Control/Test */
#1 lore raw

PATCH 2/2 skge: comma consistency

Use comma's consistently.

---
 drivers/net/skge.c |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/net/skge.c +2 -2
@@ -77,13 +77,13 @@
 	{ PCI_DEVICE(PCI_VENDOR_ID_3COM, PCI_DEVICE_ID_3COM_3C940B) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, PCI_DEVICE_ID_SYSKONNECT_GE) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, PCI_DEVICE_ID_SYSKONNECT_YU) },
-	{ PCI_DEVICE(PCI_VENDOR_ID_DLINK, PCI_DEVICE_ID_DLINK_DGE510T), },
+	{ PCI_DEVICE(PCI_VENDOR_ID_DLINK, PCI_DEVICE_ID_DLINK_DGE510T) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4b01) },	/* DGE-530T */
 	{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4320) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x5005) }, /* Belkin */
 	{ PCI_DEVICE(PCI_VENDOR_ID_CNET, PCI_DEVICE_ID_CNET_GIGACARD) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_LINKSYS, PCI_DEVICE_ID_LINKSYS_EG1064) },
-	{ PCI_VENDOR_ID_LINKSYS, 0x1032, PCI_ANY_ID, 0x0015, },
+	{ PCI_VENDOR_ID_LINKSYS, 0x1032, PCI_ANY_ID, 0x0015 },
 	{ 0 }
 };
 MODULE_DEVICE_TABLE(pci, skge_id_table);
Applied
#2 lore raw
In reply to Stephen Hemminger
Quoted 7 lines · Stephen Hemminger

It looks like the skge driver inherited another bug from the sk98lin code. If I send from 1000mbit port to a machine on 100mbit port, the switch should be doing hardware flow control, but no pause frames show up in the statistics.

This is the analog of the recent sky2 fixes. The device needs to listen for multicast pause frames and then not discard them.

Quoted 6 lines
---
 drivers/net/skge.c |   43 ++++++++++++++++++++++++++++++++-----------
 drivers/net/skge.h |    3 +--
 2 files changed, 33 insertions(+), 13 deletions(-)

applied