Conflict between ide and usb?
Hi all.
I installed ueagle-atm, which, by itself, is working fine with an MT-810 modem.
The problem I have, is that when I copy a file from a DVD to harddisk, the internet connection almost dies (it slows down terribly, so much so that established connections actually disconnect, ping looses packets, DNS lookup fails, etc). After copy ends, all returns to normal.
The machine is an AMD64, still in x86 mode though. CPU activity is very low during the copy, so it's not a CPU problem. Kernel is 2.6.20.2. APIC is enabled. No error message found in either /var/log/messages or syslog. DVD and HD are on different IDE interfaces.
Can anyone suggest where to start looking for a solution?
Cheers,
John
$ cat interrupts
CPU0 CPU1
0: 58428350 6031800 XT-PIC-XT timer
1: 204337 9 IO-APIC-edge i8042
6: 0 3 IO-APIC-edge floppy
7: 6031308 58426101 IO-APIC-edge parport0
9: 0 0 IO-APIC-fasteoi acpi
12: 211041 5153326 IO-APIC-edge i8042
14: 93535 316012 IO-APIC-edge ide0
15: 246534 40 IO-APIC-edge ide1
16: 2591 1737056 IO-APIC-fasteoi libata, HDA Intel
17: 41 1 IO-APIC-fasteoi libata, ehci_hcd:usb2
18: 7717494 19142555 IO-APIC-fasteoi eth0
19: 0 0 IO-APIC-fasteoi eth1
20: 90833792 3057782 IO-APIC-fasteoi ohci_hcd:usb1
21: 22135804 1 IO-APIC-fasteoi nvidia
22: 0 0 IO-APIC-fasteoi saa7130[0]
NMI: 0 0
LOC: 64460593 64460595
ERR: 1
MIS: 0$ lsmod Module Size Used by pppoe 9792 2 pppox 3016 1 pppoe ppp_generic 21396 6 pppoe,pppox slhc 5440 1 ppp_generic br2684 6596 1 i2c_viapro 7380 0 w83627ehf 16140 0 i2c_isa 4096 1 w83627ehf snd_seq_oss 26368 0 snd_seq_midi_event 5952 1 snd_seq_oss snd_seq 41232 4 snd_seq_oss,snd_seq_midi_event snd_seq_device 6284 2 snd_seq_oss,snd_seq snd_pcm_oss 34912 0 snd_mixer_oss 13376 4 snd_pcm_oss ipt_REJECT 3648 1 ipt_MASQUERADE 2944 1 ipt_LOG 5760 1 xt_limit 2560 1 xt_state 2368 3 iptable_filter 2688 1 iptable_nat 6020 1 nf_nat 13740 2 ipt_MASQUERADE,iptable_nat nf_conntrack_ipv4 11980 5 iptable_nat nf_conntrack 44168 5 ipt_MASQUERADE,xt_state,iptable_nat,nf_nat,nf_conntrack_ipv4 ip_tables 9700 2 iptable_filter,iptable_nat ueagle_atm 21032 0 firmware_class 7360 1 ueagle_atm usbatm 14464 2 ueagle_atm atm 33716 4 br2684,usbatm usblp 11136 0 ide_scsi 13128 0 tuner 55272 0 saa7134 105952 0 snd_hda_intel 15192 3 snd_hda_codec 149120 1 snd_hda_intel video_buf 18500 1 saa7134 compat_ioctl32 1536 1 saa7134 ir_kbd_i2c 6928 1 saa7134 ir_common 26372 2 saa7134,ir_kbd_i2c ehci_hcd 24332 0 ohci_hcd 16708 0 videodev 23488 1 saa7134 snd_pcm 61124 3 snd_pcm_oss,snd_hda_intel,snd_hda_codec snd_timer 16836 2 snd_seq,snd_pcm snd 39268 9 snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss,snd_mixer_oss,snd_hda_intel,snd_hda_codec,snd_pcm,snd_timer snd_page_alloc 7368 2 snd_hda_intel,snd_pcm sg 19032 0 i2c_nforce2 4800 0 nvidia 6817908 22 v4l2_common 21312 3 tuner,saa7134,videodev v4l1_compat 12036 2 saa7134,videodev k8temp 4544 0 usbcore 101768 6 ueagle_atm,usbatm,usblp,ehci_hcd,ohci_hcd ne2k_pci 8736 0 8390 7808 1 ne2k_pci forcedeth 37192 0 parport_pc 22628 0 parport 30728 1 parport_pc
Quoted 4 lines · John Coppens
The problem I have, is that when I copy a file from a DVD to harddisk, the internet connection almost dies (it slows down terribly, so much so that established connections actually disconnect, ping looses packets, DNS lookup fails, etc). After copy ends, all returns to normal.
Sounds like DMA starvation, it's been seen in the past with some SATA controllers. Presumably vendors do it to improve benchmark scores.
You can confirm it by forcing the hard drive and/or DVD drive to a lower speed if your BIOS allows it.
Lee
Quoted 9 lines · On Fri, 16 Mar 2007 15:52:12 -0400 "Lee Revell" <[email protected]> wrote:
Quoted 5 lines · John Coppens
The problem I have, is that when I copy a file from a DVD to harddisk, the internet connection almost dies (it slows down terribly, so much so that established connections actually disconnect, ping looses packets, DNS lookup fails, etc). After copy ends, all returns to normal.
Sounds like DMA starvation, it's been seen in the past with some SATA controllers. Presumably vendors do it to improve benchmark scores.
Hi Lee.
In this case SATA isn't used, as the copy is from IDE to IDE. But I doubt bandwidth has anything to do with it. The DVD transfer rate rarely reaches 3.3 MB/s - which by itself isn't normal.
Quoted 2 lines
You can confirm it by forcing the hard drive and/or DVD drive to a lower speed if your BIOS allows it.
No... I didn't find any way to lower the speed.
Thanks
John
Quoted 1 line · John Coppens
No... I didn't find any way to lower the speed.
Do you even have DMA enabled for the DVD drive? Without it it will be very slow and painful for the CPU. I also have noticed that many fast (16x) DVD writers must have an 80 wire cable or they won't work correctly and do nasty things to the system.
Check /proc/ide/hdX/settings|grep dma and see if it says 1 0 1 or 0 0 1.
--
Len Sorensen
Quoted 6 lines · On Fri, 16 Mar 2007 16:34:15 -0400 [email protected] (Lennart…
Do you even have DMA enabled for the DVD drive? Without it it will be very slow and painful for the CPU. I also have noticed that many fast (16x) DVD writers must have an 80 wire cable or they won't work correctly and do nasty things to the system.
Check /proc/ide/hdX/settings|grep dma and see if it says 1 0 1 or 0 0 1.
I _knew_ I enabled the DMA, but it seems that is switches off when I start the transfer:
hdc: DMA disabled
hdc: ide_intr: huh? expected NULL handler on exit
hdc: ATAPI reset complete
ISO 9660 Extensions: RRIP_1991A
VFS: busy inodes on changed media.
This is on hdc, which is the DVD. Harddisk has DMA on.
John
Quoted 3 lines · On Fri, 16 Mar 2007 16:34:15 -0400 [email protected] (Lennart…
I also have noticed that many fast
(16x) DVD writers must have an 80 wire cable or they won't work correctly and do nasty things to the system.
That was the problem! This is the first machine I bought assembled, and I hadn't noticed that the CD/DVD cables were the old 40 wire cables. I do hope this is the last of the problems.
Thanks guys! Changed the cable, and speed went up from 3.3 to 19MB/s (probably limited by the older harddrive too)... Thas was spectacular! Of course, now DMA didn't switch off either.
Cheers,
John
Quoted 15 lines · John Coppens
Hi all.
I installed ueagle-atm, which, by itself, is working fine with an MT-810 modem.
The problem I have, is that when I copy a file from a DVD to harddisk, the internet connection almost dies (it slows down terribly, so much so that established connections actually disconnect, ping looses packets, DNS lookup fails, etc). After copy ends, all returns to normal.
The machine is an AMD64, still in x86 mode though. CPU activity is very low during the copy, so it's not a CPU problem. Kernel is 2.6.20.2. APIC is enabled. No error message found in either
/var/log/messagesor syslog. DVD and HD are on different IDE interfaces.Can anyone suggest where to start looking for a solution?
..
Quoted 2 lines
16: 2591 1737056 IO-APIC-fasteoi libata, HDA Intel 17: 41 1 IO-APIC-fasteoi libata, ehci_hcd:usb2
..
It pretty much has to be an IRQ sharing issue, most likely in the USB driver side of the house.
I don't know enough about the USB drivers really, but the interrupt routine inside the ueagle-atm.c file doesn't seem too "sharing friendly". But perhaps that part is handled by the layers above (?).
That's where I'd start looking if I were you.
-ml
Quoted 14 lines · Mark Lord
Quoted 12 lines · John Coppens
I installed ueagle-atm, which, by itself, is working fine with an MT-810 modem.
The problem I have, is that when I copy a file from a DVD to harddisk, the internet connection almost dies (it slows down terribly, so much so that established connections actually disconnect, ping looses packets, DNS lookup fails, etc). After copy ends, all returns to normal.
The machine is an AMD64, still in x86 mode though. CPU activity is very low during the copy, so it's not a CPU problem. Kernel is 2.6.20.2. APIC is enabled. No error message found in either
/var/log/messagesor syslog. DVD and HD are on different IDE interfaces.
Quoted 8 lines
Quoted 1 line
Can anyone suggest where to start looking for a solution?
..
Quoted 2 lines
16: 2591 1737056 IO-APIC-fasteoi libata, HDA Intel 17: 41 1 IO-APIC-fasteoi libata, ehci_hcd:usb2..
It pretty much has to be an IRQ sharing issue,
most likely in the USB driver side of the house.
Oh, wait a minute.. that's not the correct IRQ, is it?
Your ueagle-atm must be on this one:
20: 90833792 3057782 IO-APIC-fasteoi ohci_hcd:usb1
In which case, it's not likely to be an interrupt sharing issue. Can you confirm this?
Also, try moving your ueagle-atm to one of the ehci usb ports and see how that affects things.