Skip to contentSkip to conversation

Clockevents: one-shoot mode is never enabled if local apic timer is disabled

DISCUSSION Maxim Levitsky 2 participants 4 messages Apr 2, 2007

lore
Share & tools
lore
#0 lore raw

Hi,

I finally figured out why one-shoot mode is enabled on my system only and only if local apic is enabled.

While reading through dynatic code it looks that all clockevent devices are put in periodic mode. Then hrtimer_run_queues (which runs nevertheless CONFIG_HIGH_RES_TIMERS enabled or not) calls indirectly (through tick_check_oneshot_change or hrtimer_switch_to_hres) to tick_switch_to_oneshot

tick_switch_to_oneshot checks that current cpu's clockevents device (and it is lapic even if not used) is not a dummy device and it is , so it never calls tick_broadcast_switch_to_oneshot

To put it simply if broadcast is used, it works in periodic mode only. tick_broadcast_switch_to_oneshot is never called (well it is called when broadcast is not used, but it is unnecessary, on my system for example it brings HPET on one-shoot mode, and HPET is not used at all)

I tried to remove this check and this resulted in hard lock-up during boot with nolapic_timer Maybe this was connected to the fact that this function is called on both cpus, and if one set a broadcasting device(HPET) to one shoot mode, second is still not aware of this.

Is it a bug or feature ?

Best regards,
Maxim Levitsky

#1 lore raw

Maxim,

can you please fix your mail client to do proper line wraps at 78 chars ?

Quoted 4 lines · Maxim Levitsky

Hi,

I finally figured out why one-shoot mode is enabled on my system only and only if local apic is enabled.

You could have asked me :)

Quoted 8 lines

I tried to remove this check and this resulted in hard lock-up during boot with nolapic_timer
Maybe this was connected to the fact that this function is called on both cpus, and if one set a
broadcasting device(HPET) to one shoot mode, second is still not aware of this.

Is it a bug or feature ?

One shot mode - used for NO_HZ and HIGH_RES - requires a working per cpu timer.

When you disable the lapic timers, then we register the lapic timers just as dummy devices to utilize the broadcast mechanism. Otherwise the second CPU would be not working at all. I decided not to enable nohz/highres when we have no usable per cpu devices available.

So consider it a feature :)

tglx

#2 lore raw
Quoted 4 lines · On Monday 02 April 2007 12:34:44 Thomas Gleixner wrote:

Maxim,

can you please fix your mail client to do proper line wraps at 78 chars ?

Sure, but this way it mangles patches :-)

Quoted 8 lines · Maxim Levitsky
Quoted 4 lines

Hi,

I finally figured out why one-shoot mode is enabled on my system only and only if local apic is enabled.

You could have asked me :)

Thanks

Quoted 13 lines
Quoted 9 lines

I tried to remove this check and this resulted in hard lock-up during boot with nolapic_timer
Maybe this was connected to the fact that this function is called on both cpus, and if one set a
broadcasting device(HPET) to one shoot mode, second is still not aware of this.

Is it a bug or feature ?

One shot mode - used for NO_HZ and HIGH_RES - requires a working per cpu timer.

Quoted 11 lines

When you disable the lapic timers, then we register the lapic timers just as dummy devices to utilize the broadcast mechanism. Otherwise the second CPU would be not working at all. I decided not to enable nohz/highres when we have no usable per cpu devices available.

So consider it a feature :)

tglx

Hi,

Fortunately on my system lapic timer works.
But then tick_broadcast_switch_to_oneshot is redundant, isn't it?

Thanks for quick answer,
Best regards,
Maxim Levitsky

#3 lore raw
Quoted 4 lines · Maxim Levitsky

Hi,

Fortunately on my system lapic timer works.
But then tick_broadcast_switch_to_oneshot is redundant, isn't it?

No, it's necessary for the systems where the local APIC timer stops in C3(C2), as we do not know this at the point where we setup the local APIC.

tglx