ARCH_OMAP243x vs. ARCH_OMAP2430
Subsystems (6)
In working on the platform support for MUSB for the 2430sdp, I noticed that there are #ifdefs for CONFIG_ARCH_OMAP2430 and CONFIG_ARCH_OMAP243X. In the Kconfigs, only the following are available:
CONFIG_ARCH_OMAP2CONFIG_ARCH_OMAP24XXCONFIG_ARCH_OMAP2420CONFIG_ARCH_OMAP2430
But in the MUSB code as well as prcm-regs.h there are #ifdefs for
OMAP243X. Are there other 243x platforms in the wild, or should I just
convert these #ifdefs to 2430. If converting is the right thing, here's a patch.
Kevin
--- arch/arm/mach-omap2/prcm-regs.h | 4 ++-- drivers/usb/musb/musbdefs.h | 2 +- drivers/usb/musb/omap2430.h | 2 +- drivers/usb/musb/plat_uds.c | 2 +- 4 files changed, 5 insertions(+), 5 deletions(-)
arch/arm/mach-omap2/prcm-regs.h +2 -2
@@ -240,7 +240,7 @@#define GPIO3_SYSCONFIG __REG32((GPIOX_BASE(3) + 0x10))#define GPIO4_SYSCONFIG __REG32((GPIOX_BASE(4) + 0x10)) -#if defined(CONFIG_ARCH_OMAP243X ) +#if defined(CONFIG_ARCH_OMAP2430 )#define GPIO5_SYSCONFIG __REG32((OMAP24XX_GPIO5_BASE + 0x10))#endif
@@ -332,7 +332,7 @@#define GPIO4_DEBOUNCENABLE GPIO4_REG32(0x050)#define GPIO4_DEBOUNCINGTIME GPIO4_REG32(0x054) -#if defined(CONFIG_ARCH_OMAP243X ) +#if defined(CONFIG_ARCH_OMAP2430 )/* GPIO 5 */ #define GPIO5_REG32 (offset) __REG32((OMAP24XX_GPIO5_BASE + (offset)))#define GPIO5_IRQENABLE1 GPIO5_REG32(0x01C)
drivers/usb/musb/musbdefs.h +1 -1
@@ -202,7 +202,7 @@ enum musb_g_ep0_state {* directly with the "flat" model, or after setting up an index register. */ -#if defined(CONFIG_ARCH_DAVINCI ) || defined(CONFIG_ARCH_OMAP243X ) +#if defined(CONFIG_ARCH_DAVINCI ) || defined(CONFIG_ARCH_OMAP2430 )/* REVISIT indexed access seemed to * misbehave (on DaVinci) for at least peripheral IN ... */
drivers/usb/musb/omap2430.h +1 -1
@@ -26,6 +26,6 @@#define OTG_INTERFSEL HS_OTG(0x40c)#define OTG_SIMENABLE HS_OTG(0x410) -#endif /* CONFIG_ARCH_OMAP243X */ +#endif /* CONFIG_ARCH_OMAP2430 */ #endif /* __MUSB_OMAP243X_H__ */
drivers/usb/musb/plat_uds.c +1 -1
@@ -1302,7 +1302,7 @@ static int __init musb_core_init(u16 wTy/*-------------------------------------------------------------------------*/ -#ifdef CONFIG_ARCH_OMAP243X +#ifdef CONFIG_ARCH_OMAP2430 static irqreturn_t generic_interrupt (int irq,void *__hci) {
Quoted 2 lines
But in the MUSB code as well as
prcm-regs.hthere are #ifdefs for
OMAP243X. Are there other 243x platforms in the wild, or should I
just
Quoted 1 line
convert these #ifdefs to 2430. If converting is the right thing,
here's
Quoted 1 line
a patch.
Those 243X's are used in MV and TI trees. I don't think the GIT one used it. They probably snuck in on your end or in previous pushes candidates from others.
They all have to be the same for sure. Looks like a good thing to fix.
Regards,
Richard W.
[email protected]
maintainerQuoted 4 lines · Woodruff, Richard
Quoted 2 lines
But in the MUSB code as well as
prcm-regs.hthere are #ifdefs for
OMAP243X. Are there other 243x platforms in the wild, or should Ijust
Quoted 1 line
convert these #ifdefs to 2430. If converting is the right thing,
Quoted 8 lines
here's
Quoted 1 line
a patch.
Those 243X's are used in MV and TI trees. I don't think the GIT one used it. They probably snuck in on your end or in previous pushes candidates from others.
They all have to be the same for sure. Looks like a good thing to fix.
This is now pushed too.
Tony