Skip to contentSkip to conversation

libata /dev/scd0 problem: mount after burn fails without eject

DISCUSSION Frank van Maarseveen 5 participants 8 messages May 1, 2007 – May 4, 2007

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

Tested on 2.6.20.6 and 2.6.21.1

I decided to swich from the old IDE drivers to libata and now there seems to be a little but annoying problem: cannot mount an ISO image after burning it.

May  1 14:32:55 kernel: attempt to access beyond end of device
May  1 14:32:55 kernel: sr0: rw=0, want=68, limit=4
May  1 14:32:55 kernel: isofs_fill_super: bread failed, dev=sr0, iso_blknum=16, block=16

an "eject" command seems to fix the state of the PATA DVD writer or driver. The problem occurs for burning a CD and for DVD too with identical error messages.

relevant kernel boot messages:

| ata1: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001ffa0 irq 14
| ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001ffa8 irq 15
| scsi0 : ata_piix
| ata1.00: ATA-7: ST3120814A, 3.AAJ, max UDMA/100
| ata1.00: 234441648 sectors, multi 8: LBA48 
| ata1.00: configured for UDMA/100
| scsi1 : ata_piix
| ata2.00: ATAPI, max UDMA/33
| ata2.01: ATAPI, max UDMA/33
| ata2.00: configured for UDMA/33
| ata2.01: configured for UDMA/33
| scsi 0:0:0:0: Direct-Access     ATA      ST3120814A       3.AA PQ: 0 ANSI: 5
| SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
| sda: Write Protect is off
| SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
| SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
| sda: Write Protect is off
| SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
|  sda: sda1 sda2 sda4
| sd 0:0:0:0: Attached scsi disk sda
| sd 0:0:0:0: Attached scsi generic sg0 type 0
| scsi 1:0:0:0: CD-ROM            HP       DVD Writer 640c  CS30 PQ: 0 ANSI: 5
| sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
| Uniform CD-ROM driver Revision: 3.20
| sr 1:0:0:0: Attached scsi generic sg1 type 5
| scsi 1:0:1:0: CD-ROM            SAMSUNG  CD-ROM SC-148C   B105 PQ: 0 ANSI: 5
| sr1: scsi3-mmc drive: 1x/48x cd/rw xa/form2 cdda tray
| sr 1:0:1:0: Attached scsi generic sg2 type 5

stripped config (well, as far of I'm sure it shouldn't matter):

| CONFIG_PM=y
| CONFIG_PM_LEGACY=y
| 
| CONFIG_ACPI=y
| CONFIG_ACPI_PROCFS=y
| CONFIG_ACPI_FAN=y
| CONFIG_ACPI_PROCESSOR=y
| CONFIG_ACPI_THERMAL=y
| CONFIG_ACPI_BLACKLIST_YEAR=0
| CONFIG_ACPI_EC=y
| CONFIG_ACPI_POWER=y
| CONFIG_ACPI_SYSTEM=y
| CONFIG_X86_PM_TIMER=y
| 
| CONFIG_PCI=y
| CONFIG_PCI_GOANY=y
| CONFIG_PCI_BIOS=y
| CONFIG_PCI_DIRECT=y
| CONFIG_PCI_MMCONFIG=y
| CONFIG_PCIEPORTBUS=y
| CONFIG_PCIEAER=y
| CONFIG_HT_IRQ=y
| CONFIG_ISA_DMA_API=y
| 
| CONFIG_PNP=y
| 
| CONFIG_PNPACPI=y
| 
| CONFIG_CDROM_PKTCDVD=y
| CONFIG_CDROM_PKTCDVD_BUFFERS=8
| 
| CONFIG_IDE=y
| 
| CONFIG_RAID_ATTRS=y
| CONFIG_SCSI=y
| CONFIG_SCSI_PROC_FS=y
| 
| CONFIG_BLK_DEV_SD=y
| CONFIG_BLK_DEV_SR=y
| CONFIG_CHR_DEV_SG=y
| 
| CONFIG_SCSI_MULTI_LUN=y
| CONFIG_SCSI_CONSTANTS=y
| CONFIG_SCSI_LOGGING=y
| 
| CONFIG_SCSI_SPI_ATTRS=y
| 
| CONFIG_ATA=y
| CONFIG_SATA_AHCI=y
| CONFIG_ATA_PIIX=y
| CONFIG_SATA_INTEL_COMBINED=y
| CONFIG_SATA_ACPI=y
| CONFIG_PATA_SERVERWORKS=y

lspci:
00:00.0 Host bridge: Intel Corporation 82845G/GL[Brookdale-G]/GE/PE DRAM Controller/Host-Hub Interface (rev 01) 00:01.0 PCI bridge: Intel Corporation 82845G/GL[Brookdale-G]/GE/PE Host-to-AGP Bridge (rev 01)
00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 01) 00:1d.1 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 01) 00:1d.2 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 01) 00:1d.7 USB Controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 01) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 81)
00:1f.0 ISA bridge: Intel Corporation 82801DB/DBL (ICH4/ICH4-L) LPC Interface Bridge (rev 01)
00:1f.1 IDE interface: Intel Corporation 82801DB (ICH4) IDE Controller (rev 01)
00:1f.3 SMBus: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev 01)
00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 01) 01:00.0 VGA compatible controller: nVidia Corporation NV18 [GeForce4 MX 440 AGP 8x] (rev a2)
02:0c.0 Ethernet controller: Intel Corporation 82541PI Gigabit Ethernet Controller (rev 05)

lspci -v -v -v for IDE
00:1f.1 IDE interface: Intel Corporation 82801DB (ICH4) IDE Controller (rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: Dell Unknown device 0142
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at ffa0 [size=16]
Region 5: Memory at 50100000 (32-bit, non-prefetchable) [size=1K]

Signature · 1 line
Frank
#1 lore raw

Forwarding to linux-scsi and linux-ide mailing lists.

Quoted 118 lines · Frank van Maarseveen

Tested on 2.6.20.6 and 2.6.21.1

I decided to swich from the old IDE drivers to libata and now there seems to be a little but annoying problem: cannot mount an ISO image after burning it.

May  1 14:32:55 kernel: attempt to access beyond end of device
May  1 14:32:55 kernel: sr0: rw=0, want=68, limit=4
May  1 14:32:55 kernel: isofs_fill_super: bread failed, dev=sr0, iso_blknum=16, block=16

an "eject" command seems to fix the state of the PATA DVD writer or driver. The problem occurs for burning a CD and for DVD too with identical error messages.

relevant kernel boot messages:

| ata1: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001ffa0 irq 14
| ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001ffa8 irq 15
| scsi0 : ata_piix
| ata1.00: ATA-7: ST3120814A, 3.AAJ, max UDMA/100
| ata1.00: 234441648 sectors, multi 8: LBA48 | ata1.00: configured for UDMA/100
| scsi1 : ata_piix
| ata2.00: ATAPI, max UDMA/33
| ata2.01: ATAPI, max UDMA/33
| ata2.00: configured for UDMA/33
| ata2.01: configured for UDMA/33
| scsi 0:0:0:0: Direct-Access     ATA      ST3120814A       3.AA PQ: 0 ANSI: 5
| SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
| sda: Write Protect is off
| SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
| SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
| sda: Write Protect is off
| SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
|  sda: sda1 sda2 sda4
| sd 0:0:0:0: Attached scsi disk sda
| sd 0:0:0:0: Attached scsi generic sg0 type 0
| scsi 1:0:0:0: CD-ROM            HP       DVD Writer 640c  CS30 PQ: 0 ANSI: 5
| sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
| Uniform CD-ROM driver Revision: 3.20
| sr 1:0:0:0: Attached scsi generic sg1 type 5
| scsi 1:0:1:0: CD-ROM            SAMSUNG  CD-ROM SC-148C   B105 PQ: 0 ANSI: 5
| sr1: scsi3-mmc drive: 1x/48x cd/rw xa/form2 cdda tray
| sr 1:0:1:0: Attached scsi generic sg2 type 5

stripped config (well, as far of I'm sure it shouldn't matter):

| CONFIG_PM=y
| CONFIG_PM_LEGACY=y
| | CONFIG_ACPI=y
| CONFIG_ACPI_PROCFS=y
| CONFIG_ACPI_FAN=y
| CONFIG_ACPI_PROCESSOR=y
| CONFIG_ACPI_THERMAL=y
| CONFIG_ACPI_BLACKLIST_YEAR=0
| CONFIG_ACPI_EC=y
| CONFIG_ACPI_POWER=y
| CONFIG_ACPI_SYSTEM=y
| CONFIG_X86_PM_TIMER=y
| | CONFIG_PCI=y
| CONFIG_PCI_GOANY=y
| CONFIG_PCI_BIOS=y
| CONFIG_PCI_DIRECT=y
| CONFIG_PCI_MMCONFIG=y
| CONFIG_PCIEPORTBUS=y
| CONFIG_PCIEAER=y
| CONFIG_HT_IRQ=y
| CONFIG_ISA_DMA_API=y
| | CONFIG_PNP=y
| | CONFIG_PNPACPI=y
| | CONFIG_CDROM_PKTCDVD=y
| CONFIG_CDROM_PKTCDVD_BUFFERS=8
| | CONFIG_IDE=y
| | CONFIG_RAID_ATTRS=y
| CONFIG_SCSI=y
| CONFIG_SCSI_PROC_FS=y
| | CONFIG_BLK_DEV_SD=y
| CONFIG_BLK_DEV_SR=y
| CONFIG_CHR_DEV_SG=y
| | CONFIG_SCSI_MULTI_LUN=y
| CONFIG_SCSI_CONSTANTS=y
| CONFIG_SCSI_LOGGING=y
| | CONFIG_SCSI_SPI_ATTRS=y
| | CONFIG_ATA=y
| CONFIG_SATA_AHCI=y
| CONFIG_ATA_PIIX=y
| CONFIG_SATA_INTEL_COMBINED=y
| CONFIG_SATA_ACPI=y
| CONFIG_PATA_SERVERWORKS=y

lspci:
00:00.0 Host bridge: Intel Corporation 82845G/GL[Brookdale-G]/GE/PE DRAM Controller/Host-Hub Interface (rev 01) 00:01.0 PCI bridge: Intel Corporation 82845G/GL[Brookdale-G]/GE/PE Host-to-AGP Bridge (rev 01)
00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 01) 00:1d.1 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 01) 00:1d.2 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 01) 00:1d.7 USB Controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 01) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 81)
00:1f.0 ISA bridge: Intel Corporation 82801DB/DBL (ICH4/ICH4-L) LPC Interface Bridge (rev 01)
00:1f.1 IDE interface: Intel Corporation 82801DB (ICH4) IDE Controller (rev 01)
00:1f.3 SMBus: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev 01)
00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 01) 01:00.0 VGA compatible controller: nVidia Corporation NV18 [GeForce4 MX 440 AGP 8x] (rev a2)
02:0c.0 Ethernet controller: Intel Corporation 82541PI Gigabit Ethernet Controller (rev 05)

lspci -v -v -v for IDE
00:1f.1 IDE interface: Intel Corporation 82801DB (ICH4) IDE Controller (rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: Dell Unknown device 0142
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at ffa0 [size=16]
Region 5: Memory at 50100000 (32-bit, non-prefetchable) [size=1K]

#2 lore raw
Quoted 133 lines · Mark Lord

Forwarding to linux-scsi and linux-ide mailing lists.

Quoted 130 lines · Frank van Maarseveen

Tested on 2.6.20.6 and 2.6.21.1

I decided to swich from the old IDE drivers to libata and now there seems to be a little but annoying problem: cannot mount an ISO image after burning it.

May  1 14:32:55 kernel: attempt to access beyond end of device
May  1 14:32:55 kernel: sr0: rw=0, want=68, limit=4
May  1 14:32:55 kernel: isofs_fill_super: bread failed, dev=sr0, iso_blknum=16, block=16

an "eject" command seems to fix the state of the PATA DVD writer or driver. The problem occurs for burning a CD and for DVD too with identical error messages.

relevant kernel boot messages:

| ata1: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001ffa0 irq 14
| ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001ffa8 irq 15
| scsi0 : ata_piix
| ata1.00: ATA-7: ST3120814A, 3.AAJ, max UDMA/100
| ata1.00: 234441648 sectors, multi 8: LBA48
| ata1.00: configured for UDMA/100
| scsi1 : ata_piix
| ata2.00: ATAPI, max UDMA/33
| ata2.01: ATAPI, max UDMA/33
| ata2.00: configured for UDMA/33
| ata2.01: configured for UDMA/33
| scsi 0:0:0:0: Direct-Access     ATA      ST3120814A       3.AA PQ: 0 ANSI: 5
| SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
| sda: Write Protect is off
| SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
| SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
| sda: Write Protect is off
| SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
|  sda: sda1 sda2 sda4
| sd 0:0:0:0: Attached scsi disk sda
| sd 0:0:0:0: Attached scsi generic sg0 type 0
| scsi 1:0:0:0: CD-ROM            HP       DVD Writer 640c  CS30 PQ: 0 ANSI: 5
| sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
| Uniform CD-ROM driver Revision: 3.20
| sr 1:0:0:0: Attached scsi generic sg1 type 5
| scsi 1:0:1:0: CD-ROM            SAMSUNG  CD-ROM SC-148C   B105 PQ: 0 ANSI: 5
| sr1: scsi3-mmc drive: 1x/48x cd/rw xa/form2 cdda tray
| sr 1:0:1:0: Attached scsi generic sg2 type 5

stripped config (well, as far of I'm sure it shouldn't matter):

| CONFIG_PM=y
| CONFIG_PM_LEGACY=y
|
| CONFIG_ACPI=y
| CONFIG_ACPI_PROCFS=y
| CONFIG_ACPI_FAN=y
| CONFIG_ACPI_PROCESSOR=y
| CONFIG_ACPI_THERMAL=y
| CONFIG_ACPI_BLACKLIST_YEAR=0
| CONFIG_ACPI_EC=y
| CONFIG_ACPI_POWER=y
| CONFIG_ACPI_SYSTEM=y
| CONFIG_X86_PM_TIMER=y
|
| CONFIG_PCI=y
| CONFIG_PCI_GOANY=y
| CONFIG_PCI_BIOS=y
| CONFIG_PCI_DIRECT=y
| CONFIG_PCI_MMCONFIG=y
| CONFIG_PCIEPORTBUS=y
| CONFIG_PCIEAER=y
| CONFIG_HT_IRQ=y
| CONFIG_ISA_DMA_API=y
|
| CONFIG_PNP=y
|
| CONFIG_PNPACPI=y
|
| CONFIG_CDROM_PKTCDVD=y
| CONFIG_CDROM_PKTCDVD_BUFFERS=8
|
| CONFIG_IDE=y
|
| CONFIG_RAID_ATTRS=y
| CONFIG_SCSI=y
| CONFIG_SCSI_PROC_FS=y
|
| CONFIG_BLK_DEV_SD=y
| CONFIG_BLK_DEV_SR=y
| CONFIG_CHR_DEV_SG=y
|
| CONFIG_SCSI_MULTI_LUN=y
| CONFIG_SCSI_CONSTANTS=y
| CONFIG_SCSI_LOGGING=y
|
| CONFIG_SCSI_SPI_ATTRS=y
|
| CONFIG_ATA=y
| CONFIG_SATA_AHCI=y
| CONFIG_ATA_PIIX=y
| CONFIG_SATA_INTEL_COMBINED=y
| CONFIG_SATA_ACPI=y
| CONFIG_PATA_SERVERWORKS=y

lspci:
00:00.0 Host bridge: Intel Corporation 82845G/GL[Brookdale-G]/GE/PE DRAM Controller/Host-Hub Interface (rev 01) 00:01.0 PCI bridge: Intel Corporation 82845G/GL[Brookdale-G]/GE/PE Host-to-AGP Bridge (rev 01)
00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 01) 00:1d.1 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 01) 00:1d.2 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 01) 00:1d.7 USB Controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 01) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 81)
00:1f.0 ISA bridge: Intel Corporation 82801DB/DBL (ICH4/ICH4-L) LPC Interface Bridge (rev 01)
00:1f.1 IDE interface: Intel Corporation 82801DB (ICH4) IDE Controller (rev 01)
00:1f.3 SMBus: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev 01)
00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 01) 01:00.0 VGA compatible controller: nVidia Corporation NV18 [GeForce4 MX 440 AGP 8x] (rev a2)
02:0c.0 Ethernet controller: Intel Corporation 82541PI Gigabit Ethernet Controller (rev 05)

lspci -v -v -v for IDE
00:1f.1 IDE interface: Intel Corporation 82801DB (ICH4) IDE Controller (rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: Dell Unknown device 0142
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at ffa0 [size=16]
Region 5: Memory at 50100000 (32-bit, non-prefetchable) [size=1K]

I added this to the list of known regressions
http://kernelnewbies.org/known_regressions

Alan CC'ed.

Regards,
Michal

Signature · 3 lines
Michal K. K. Piotrowski
Kernel Monkeys
(http://kernel.wikidot.com/start)
#3 lore raw
Quoted 10 lines · Michal Piotrowski
Quoted 9 lines · Mark Lord

Forwarding to linux-scsi and linux-ide mailing lists.

Quoted 6 lines · Frank van Maarseveen

Tested on 2.6.20.6 and 2.6.21.1

I decided to swich from the old IDE drivers to libata and now there seems to be a little but annoying problem: cannot mount an ISO image after burning it.

Quoted 8 lines
Quoted 8 lines
Quoted 3 lines
May  1 14:32:55 kernel: attempt to access beyond end of device
May  1 14:32:55 kernel: sr0: rw=0, want=68, limit=4
May  1 14:32:55 kernel: isofs_fill_super: bread failed, dev=sr0,

iso_blknum=16, block=16

Quoted 4 lines

an "eject" command seems to fix the state of the PATA DVD writer or driver. The problem occurs for burning a CD and for DVD too with identical error messages.

Right after burning, if you run 'fuser -v /dev/sr0', what does it say?

Signature · 1 line
tejun
#4 lore raw
Quoted 14 lines · Tejun Heo
Quoted 13 lines · Michal Piotrowski
Quoted 12 lines · Mark Lord

Forwarding to linux-scsi and linux-ide mailing lists.

Quoted 9 lines · Frank van Maarseveen

Tested on 2.6.20.6 and 2.6.21.1

I decided to swich from the old IDE drivers to libata and now there seems to be a little but annoying problem: cannot mount an ISO image after burning it.

May  1 14:32:55 kernel: attempt to access beyond end of device
May  1 14:32:55 kernel: sr0: rw=0, want=68, limit=4
May  1 14:32:55 kernel: isofs_fill_super: bread failed, dev=sr0,
Quoted 7 lines
Quoted 5 lines
Quoted 5 lines

iso_blknum=16, block=16

Quoted 4 lines

an "eject" command seems to fix the state of the PATA DVD writer or driver. The problem occurs for burning a CD and for DVD too with identical error messages.

Right after burning, if you run 'fuser -v /dev/sr0', what does it say?

Tried the fuser as root to be sure but it didn't show anything.

Signature · 1 line
Frank
#5 lore raw
Quoted 15 lines · Frank van Maarseveen
Quoted 14 lines · Tejun Heo
Quoted 13 lines · Michal Piotrowski
Quoted 12 lines · Mark Lord

Forwarding to linux-scsi and linux-ide mailing lists.

Quoted 9 lines · Frank van Maarseveen

Tested on 2.6.20.6 and 2.6.21.1

I decided to swich from the old IDE drivers to libata and now there seems to be a little but annoying problem: cannot mount an ISO image after burning it.

May  1 14:32:55 kernel: attempt to access beyond end of device
May  1 14:32:55 kernel: sr0: rw=0, want=68, limit=4
May  1 14:32:55 kernel: isofs_fill_super: bread failed, dev=sr0,
Quoted 7 lines
Quoted 5 lines
Quoted 4 lines
Quoted 4 lines

iso_blknum=16, block=16

Quoted 3 lines

an "eject" command seems to fix the state of the PATA DVD writer or driver. The problem occurs for burning a CD and for DVD too with identical error messages.

Right after burning, if you run 'fuser -v /dev/sr0', what does it say?

Tried the fuser as root to be sure but it didn't show anything.

I guess sr is forgetting to set media changed flag somewhere. Don't really know where tho. CC'd Bartlomiej, linux-scsi and linux-ide. Any ideas?

Signature · 1 line
tejun
#6 lore raw
Quoted 17 lines · Tejun Heo
Quoted 16 lines · Frank van Maarseveen
Quoted 15 lines · Tejun Heo
Quoted 14 lines · Michal Piotrowski
Quoted 13 lines · Mark Lord

Forwarding to linux-scsi and linux-ide mailing lists.

Quoted 9 lines · Frank van Maarseveen

Tested on 2.6.20.6 and 2.6.21.1

I decided to swich from the old IDE drivers to libata and now there seems to be a little but annoying problem: cannot mount an ISO image after burning it.

May  1 14:32:55 kernel: attempt to access beyond end of device
May  1 14:32:55 kernel: sr0: rw=0, want=68, limit=4
May  1 14:32:55 kernel: isofs_fill_super: bread failed, dev=sr0,

iso_blknum=16, block=16

Quoted 8 lines
Quoted 6 lines
Quoted 4 lines
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines

an "eject" command seems to fix the state of the PATA DVD writer or driver. The problem occurs for burning a CD and for DVD too with identical error messages.

Right after burning, if you run 'fuser -v /dev/sr0', what does it say?

Tried the fuser as root to be sure but it didn't show anything.

I guess sr is forgetting to set media changed flag somewhere.

Plausible. I get the same kernel messages when I try to mount the CD before burning.

Signature · 1 line
Frank
#7 lore raw
In reply to Frank van Maarseveen
Quoted 6 lines · Frank van Maarseveen

Tested on 2.6.20.6 and 2.6.21.1

I decided to swich from the old IDE drivers to libata and now there seems to be a little but annoying problem: cannot mount an ISO image after burning it.

Quoted 9 lines
May  1 14:32:55 kernel: attempt to access beyond end of device
May  1 14:32:55 kernel: sr0: rw=0, want=68, limit=4
May  1 14:32:55 kernel: isofs_fill_super: bread failed, dev=sr0,

iso_blknum=16, block=16

an "eject" command seems to fix the state of the PATA DVD writer or driver. The problem occurs for burning a CD and for DVD too with identical error messages.

I'm not sure if that's "proper" or not, but such has always been the case here. Even k3b has been ejecting and remounting the cd/dvd since forever when it is asked to do a verify pass.

Quoted 121 lines

relevant kernel boot messages:

| ata1: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001ffa0 irq
| 14 ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001ffa8
| irq 15 scsi0 : ata_piix
| ata1.00: ATA-7: ST3120814A, 3.AAJ, max UDMA/100
| ata1.00: 234441648 sectors, multi 8: LBA48
| ata1.00: configured for UDMA/100
| scsi1 : ata_piix
| ata2.00: ATAPI, max UDMA/33
| ata2.01: ATAPI, max UDMA/33
| ata2.00: configured for UDMA/33
| ata2.01: configured for UDMA/33
| scsi 0:0:0:0: Direct-Access     ATA      ST3120814A       3.AA PQ: 0 ANSI:
| 5 SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
| sda: Write Protect is off
| SCSI device sda: write cache: enabled, read cache: enabled, doesn't
| support DPO or FUA SCSI device sda: 234441648 512-byte hdwr sectors
| (120034 MB)
| sda: Write Protect is off
| SCSI device sda: write cache: enabled, read cache: enabled, doesn't
| support DPO or FUA sda: sda1 sda2 sda4
| sd 0:0:0:0: Attached scsi disk sda
| sd 0:0:0:0: Attached scsi generic sg0 type 0
| scsi 1:0:0:0: CD-ROM            HP       DVD Writer 640c  CS30 PQ: 0 ANSI:
| 5 sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
| Uniform CD-ROM driver Revision: 3.20
| sr 1:0:0:0: Attached scsi generic sg1 type 5
| scsi 1:0:1:0: CD-ROM            SAMSUNG  CD-ROM SC-148C   B105 PQ: 0 ANSI:
| 5 sr1: scsi3-mmc drive: 1x/48x cd/rw xa/form2 cdda tray
| sr 1:0:1:0: Attached scsi generic sg2 type 5

stripped config (well, as far of I'm sure it shouldn't matter):

| CONFIG_PM=y
| CONFIG_PM_LEGACY=y
|
| CONFIG_ACPI=y
| CONFIG_ACPI_PROCFS=y
| CONFIG_ACPI_FAN=y
| CONFIG_ACPI_PROCESSOR=y
| CONFIG_ACPI_THERMAL=y
| CONFIG_ACPI_BLACKLIST_YEAR=0
| CONFIG_ACPI_EC=y
| CONFIG_ACPI_POWER=y
| CONFIG_ACPI_SYSTEM=y
| CONFIG_X86_PM_TIMER=y
|
| CONFIG_PCI=y
| CONFIG_PCI_GOANY=y
| CONFIG_PCI_BIOS=y
| CONFIG_PCI_DIRECT=y
| CONFIG_PCI_MMCONFIG=y
| CONFIG_PCIEPORTBUS=y
| CONFIG_PCIEAER=y
| CONFIG_HT_IRQ=y
| CONFIG_ISA_DMA_API=y
|
| CONFIG_PNP=y
|
| CONFIG_PNPACPI=y
|
| CONFIG_CDROM_PKTCDVD=y
| CONFIG_CDROM_PKTCDVD_BUFFERS=8
|
| CONFIG_IDE=y
|
| CONFIG_RAID_ATTRS=y
| CONFIG_SCSI=y
| CONFIG_SCSI_PROC_FS=y
|
| CONFIG_BLK_DEV_SD=y
| CONFIG_BLK_DEV_SR=y
| CONFIG_CHR_DEV_SG=y
|
| CONFIG_SCSI_MULTI_LUN=y
| CONFIG_SCSI_CONSTANTS=y
| CONFIG_SCSI_LOGGING=y
|
| CONFIG_SCSI_SPI_ATTRS=y
|
| CONFIG_ATA=y
| CONFIG_SATA_AHCI=y
| CONFIG_ATA_PIIX=y
| CONFIG_SATA_INTEL_COMBINED=y
| CONFIG_SATA_ACPI=y
| CONFIG_PATA_SERVERWORKS=y

lspci:
00:00.0 Host bridge: Intel Corporation 82845G/GL[Brookdale-G]/GE/PE DRAM Controller/Host-Hub Interface (rev 01) 00:01.0 PCI bridge: Intel Corporation 82845G/GL[Brookdale-G]/GE/PE Host-to-AGP Bridge (rev 01) 00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 01) 00:1d.1 USB
Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 01) 00:1d.2 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 01) 00:1d.7 USB Controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 01) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 81)
00:1f.0 ISA bridge: Intel Corporation 82801DB/DBL (ICH4/ICH4-L) LPC Interface Bridge (rev 01) 00:1f.1 IDE interface: Intel Corporation 82801DB (ICH4) IDE Controller (rev 01) 00:1f.3 SMBus: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev 01) 00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 01) 01:00.0 VGA compatible
controller: nVidia Corporation NV18 [GeForce4 MX 440 AGP 8x] (rev a2) 02:0c.0 Ethernet controller: Intel Corporation 82541PI Gigabit Ethernet Controller (rev 05)

lspci -v -v -v for IDE
00:1f.1 IDE interface: Intel Corporation 82801DB (ICH4) IDE Controller (rev
01) (prog-if 8a [Master SecP PriP]) Subsystem: Dell Unknown device 0142
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0

       Interrupt: pin A routed to IRQ 17
       Region 0: I/O ports at 01f0 [size=8]
       Region 1: I/O ports at 03f4 [size=1]
       Region 2: I/O ports at 0170 [size=8]
       Region 3: I/O ports at 0374 [size=1]
       Region 4: I/O ports at ffa0 [size=16]
       Region 5: Memory at 50100000 (32-bit, non-prefetchable) [size=1K]
Signature · 6 lines
Cheers, Gene
"There are four boxes to be used in defense of liberty:
 soap, ballot, jury, and ammo. Please use in that order."
-Ed Howdershelt (Author)
Remembering is for those who have forgotten.
		-- Chinese proverb