Ebony, ready for merge

PATCH In review David Gibson 2 participants 11 messages May 8, 2007

Subsystems (5)

Device tree bindings PowerPC TTY layer and serial drivers Linux for PowerPC embedded PPC4XX +1 more subsystems

lore

Share & tools

lore

David Gibson

author

2007-05-08 02:58 UTC #0 lore raw

cover Ebony, ready for merge

Here's my latest Ebony series. I believe we're now ready to merge:
- Patch 1-2 I'm working with akpm and rmk about
- Patch 3-6 I think can go into powerpc.git, then mainline as
of now
- Patch 7, BenH's device-tree aware rewrite of the emac driver
I'm less sure about. Up to you, Paul.

Signature · 4 lines

David Gibson			| I'll have my music baroque, and my code
david AT gibson.dropbear.id.au	| minimalist, thank you.  NOT _the_ _other_
				| _way_ _around_!
http://www.ozlabs.org/~dgibson

David Gibson

author

2007-05-08 02:59 UTC #1 lore raw

PATCH 1/7 Only legacy ports should allow addr/irq changes via setserial

At present, the serial core always allows setserial in userspace to change the port address, irq and base clock of any serial port. That makes sense for legacy ISA ports, but not for PCI serial ports or (say) embedded ns16550 compatible serial ports at peculiar addresses. In these cases, the kernel code configuring the ports must know exactly where they are, and their clocking arrangements (which can be unusual on embedded boards). It doesn't make sense for userspace to change these settings.

Therefore, this patch alters uart_set_info() to ignore attempts to change a port's type, io address irq or base clock with setserial, unless that port has a new UPF_SETSERIAL_MOVABLE flag set. That flag is set only on the ports associated with the serial8250_isa_devs platform_device defined within 8250.c itself.

Signed-off-by David Gibson <[email protected]>

---

 drivers/serial/8250.c        |    3 ++-
 drivers/serial/serial_core.c |   22 +++++++++++++---------
 include/linux/serial_core.h  |    1 +
 3 files changed, 16 insertions(+), 10 deletions(-)

drivers/serial/serial_core.c +13 -9

Index: working-2.6/drivers/serial/serial_core.c
===================================================================
@@ -646,6 +646,7 @@ static int uart_set_info(struct uart_sta
 	struct serial_struct new_serial;
 	struct uart_port *port = state->port;
 	unsigned long new_port;
+	int allow_hw_change = port->flags & UPF_SETSERIAL_MOVABLE;
 	unsigned int change_irq, change_port, closing_wait;
 	unsigned int old_custom_divisor, close_delay;
 	upf_t old_flags, new_flags;

@@ -672,19 +673,20 @@ static int uart_set_info(struct uart_sta
 	 */
 	mutex_lock(&state->mutex);
 
-	change_irq  = new_serial.irq != port->irq;
+	change_irq  = allow_hw_change && (new_serial.irq != port->irq);
 
 	/*
 	 * Since changing the 'type' of the port changes its resource
 	 * allocations, we should treat type changes the same as
 	 * IO port changes.
 	 */
-	change_port = new_port != port->iobase ||
-		      (unsigned long)new_serial.iomem_base != port->mapbase ||
-		      new_serial.hub6 != port->hub6 ||
-		      new_serial.io_type != port->iotype ||
-		      new_serial.iomem_reg_shift != port->regshift ||
-		      new_serial.type != port->type;
+	change_port = allow_hw_change &&
+		(new_port != port->iobase ||
+		 (unsigned long)new_serial.iomem_base != port->mapbase ||
+		 new_serial.hub6 != port->hub6 ||
+		 new_serial.io_type != port->iotype ||
+		 new_serial.iomem_reg_shift != port->regshift ||
+		 new_serial.type != port->type);
 
 	old_flags = port->flags;
 	new_flags = new_serial.flags;

@@ -796,8 +798,10 @@ static int uart_set_info(struct uart_sta
 		}
 	}
 
-	port->irq              = new_serial.irq;
-	port->uartclk          = new_serial.baud_base * 16;
+	if (change_irq)
+		port->irq      = new_serial.irq;
+	if (allow_hw_change)
+		port->uartclk  = new_serial.baud_base * 16;
 	port->flags            = (port->flags & ~UPF_CHANGE_MASK) |
 				 (new_flags & UPF_CHANGE_MASK);
 	port->custom_divisor   = new_serial.custom_divisor;

include/linux/serial_core.h +1 -0

Index: working-2.6/include/linux/serial_core.h
===================================================================
@@ -260,6 +260,7 @@ struct uart_port {
 #define UPF_CONS_FLOW		((__force upf_t) (1 << 23))
 #define UPF_SHARE_IRQ		((__force upf_t) (1 << 24))
 #define UPF_BOOT_AUTOCONF	((__force upf_t) (1 << 28))
+#define UPF_SETSERIAL_MOVABLE	((__force upf_t) (1 << 29))
 #define UPF_DEAD		((__force upf_t) (1 << 30))
 #define UPF_IOREMAP		((__force upf_t) (1 << 31))

drivers/serial/8250.c +2 -1

Index: working-2.6/drivers/serial/8250.c
===================================================================
@@ -2308,7 +2308,8 @@ static void __init serial8250_isa_init_p
 		up->port.iobase   = old_serial_port[i].port;
 		up->port.irq      = irq_canonicalize(old_serial_port[i].irq);
 		up->port.uartclk  = old_serial_port[i].baud_base * 16;
-		up->port.flags    = old_serial_port[i].flags;
+		up->port.flags    = old_serial_port[i].flags
+			| UPF_SETSERIAL_MOVABLE;
 		up->port.hub6     = old_serial_port[i].hub6;
 		up->port.membase  = old_serial_port[i].iomem_base;
 		up->port.iotype   = old_serial_port[i].io_type;

David Gibson

author

2007-05-08 02:59 UTC #2 lore raw

PATCH 2/7 Use resource_size_t for serial port IO addresses

In reply to David Gibson

At present, various parts of the serial code use unsigned long to define resource addresses. This is a problem, because some 32-bit platforms have physical addresses larger than 32-bits, and have mmio serial uarts located above the 4GB point.

This patch changes the type of mapbase in both struct uart_port and struct plat_serial8250_port to resource_size_t, which can be configured to be 64 bits on such platforms. The mapbase in serial_struct can't safely be changed, because that structure is user visible.

Signed-off-by David Gibson <[email protected]>

---

 drivers/serial/8250.c        |    5 +++--
 drivers/serial/8250_early.c  |   16 +++++++++-------
 drivers/serial/serial_core.c |    9 +++++----
 include/linux/serial_8250.h  |    2 +-
 include/linux/serial_core.h  |    2 +-
 5 files changed, 19 insertions(+), 15 deletions(-)

include/linux/serial_core.h +1 -1

Index: working-2.6/include/linux/serial_core.h
===================================================================
@@ -273,7 +273,7 @@ struct uart_port {
 	const struct uart_ops	*ops;
 	unsigned int		custom_divisor;
 	unsigned int		line;			/* port index */
-	unsigned long		mapbase;		/* for ioremap */
+	resource_size_t		mapbase;		/* for ioremap */
 	struct device		*dev;			/* parent device */
 	unsigned char		hub6;			/* this should be in the 8250 driver */
 	unsigned char		unused[3];

drivers/serial/serial_core.c +5 -4

Index: working-2.6/drivers/serial/serial_core.c
===================================================================
@@ -633,7 +633,7 @@ static int uart_get_info(struct uart_sta
 	tmp.hub6	    = port->hub6;
 	tmp.io_type         = port->iotype;
 	tmp.iomem_reg_shift = port->regshift;
-	tmp.iomem_base      = (void *)port->mapbase;
+	tmp.iomem_base      = (void *)(unsigned long)port->mapbase;
 
 	if (copy_to_user(retinfo, &tmp, sizeof(*retinfo)))
 		return -EFAULT;

@@ -1673,10 +1673,11 @@ static int uart_line_info(char *buf, str
 		return 0;
 
 	mmio = port->iotype >= UPIO_MEM;
-	ret = sprintf(buf, "%d: uart:%s %s%08lX irq:%d",
+	ret = sprintf(buf, "%d: uart:%s %s%08llX irq:%d",
 			port->line, uart_type(port),
 			mmio ? "mmio:0x" : "port:",
-			mmio ? port->mapbase : (unsigned long) port->iobase,
+			mmio ? (unsigned long long)port->mapbase
+		             : (unsigned long long) port->iobase,
 			port->irq);
 
 	if (port->type == PORT_UNKNOWN) {

@@ -2069,7 +2070,7 @@ uart_report_port(struct uart_driver *drv
 	case UPIO_AU:
 	case UPIO_TSI:
 		snprintf(address, sizeof(address),
-			 "MMIO 0x%lx", port->mapbase);
+			 "MMIO 0x%llx", (unsigned long long)port->mapbase);
 		break;
 	default:
 		strlcpy(address, "*unknown*", sizeof(address));

drivers/serial/8250_early.c +9 -7

Index: working-2.6/drivers/serial/8250_early.c
===================================================================
@@ -145,8 +145,9 @@ static int __init parse_options(struct e
 		port->mapbase = simple_strtoul(options + 5, &options, 0);
 		port->membase = ioremap(port->mapbase, mapsize);
 		if (!port->membase) {
-			printk(KERN_ERR "%s: Couldn't ioremap 0x%lx\n",
-				__FUNCTION__, port->mapbase);
+			printk(KERN_ERR "%s: Couldn't ioremap 0x%llx\n",
+				__FUNCTION__,
+			       (unsigned long long)port->mapbase);
 			return -ENOMEM;
 		}
 		mmio = 1;

@@ -168,9 +169,10 @@ static int __init parse_options(struct e
 			device->baud);
 	}
 
-	printk(KERN_INFO "Early serial console at %s 0x%lx (options '%s')\n",
+	printk(KERN_INFO "Early serial console at %s 0x%llx (options '%s')\n",
 		mmio ? "MMIO" : "I/O port",
-		mmio ? port->mapbase : (unsigned long) port->iobase,
+		mmio ? (unsigned long long) port->mapbase
+	             : (unsigned long long) port->iobase,
 		device->options);
 	return 0;
 }

@@ -236,10 +238,10 @@ static int __init early_uart_console_swi
 	mmio = (port->iotype == UPIO_MEM);
 	line = serial8250_start_console(port, device->options);
 	if (line < 0)
-		printk("No ttyS device at %s 0x%lx for console\n",
+		printk("No ttyS device at %s 0x%llx for console\n",
 			mmio ? "MMIO" : "I/O port",
-			mmio ? port->mapbase :
-			    (unsigned long) port->iobase);
+			mmio ? (unsigned long long) port->mapbase
+		             : (unsigned long long) port->iobase);
 
 	unregister_console(&early_uart_console);
 	if (mmio)

include/linux/serial_8250.h +1 -1

Index: working-2.6/include/linux/serial_8250.h
===================================================================
@@ -20,7 +20,7 @@
 struct plat_serial8250_port {
 	unsigned long	iobase;		/* io base address */
 	void __iomem	*membase;	/* ioremap cookie or NULL */
-	unsigned long	mapbase;	/* resource base */
+	resource_size_t	mapbase;	/* resource base */
 	unsigned int	irq;		/* interrupt number */
 	unsigned int	uartclk;	/* UART clock rate */
 	unsigned char	regshift;	/* register shift */

drivers/serial/8250.c +3 -2

Index: working-2.6/drivers/serial/8250.c
===================================================================
@@ -2553,8 +2553,9 @@ static int __devinit serial8250_probe(st
 		ret = serial8250_register_port(&port);
 		if (ret < 0) {
 			dev_err(&dev->dev, "unable to register port at index %d "
-				"(IO%lx MEM%lx IRQ%d): %d\n", i,
-				p->iobase, p->mapbase, p->irq, ret);
+				"(IO%lx MEM%llx IRQ%d): %d\n", i,
+				p->iobase, (unsigned long long)p->mapbase,
+				p->irq, ret);
 		}
 	}
 	return 0;

David Gibson

author

2007-05-08 02:59 UTC #3 lore raw

PATCH 3/7 powerpc: Add powerpc/platforms/44x, disable platforms/4xx for now

In reply to David Gibson

This patch prepares for Ebony/440 support by creating an arch/powerpc/platforms/44x directory. It is populated with a single misc_44x.S file, into which is moved the 44x specific reset code from head_44x.S (on the grounds that we should really stop clogging up the head_* files with random asm helper routines).

At the same time, we disable the (empty save Kconfig and Makefile) arch/powerpc/platforms/4xx directory from the arch/powerpc/platforms Makefile. Contrary to the comment in arch/powerpc/platforms/4xx/Makefile, attempting to build such an empty Makefile will fail, thus breaking compile for the 44x platforms we're about to add. It can go back in once we start porting some of the 40x platforms (and thus it becomes non-empty).

Signed-off-by David Gibson <[email protected]>

---

 arch/powerpc/kernel/head_44x.S        |   10 ----------
 arch/powerpc/platforms/44x/44x.h      |    6 ++++++
 arch/powerpc/platforms/44x/Makefile   |    1 +
 arch/powerpc/platforms/44x/misc_44x.S |   26 ++++++++++++++++++++++++++
 arch/powerpc/platforms/Makefile       |    3 ++-
 5 files changed, 35 insertions(+), 11 deletions(-)

arch/powerpc/platforms/44x/misc_44x.S new file +26 -0

Index: working-2.6/arch/powerpc/platforms/44x/misc_44x.S
===================================================================
@@ -0,0 +1,26 @@
+/*
+ * This file contains miscellaneous low-level functions for PPC 44x.
+ *    Copyright 2007 David Gibson <[email protected]>, IBM Corporation.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ *
+ */
+
+#include <asm/reg.h>
+#include <asm/ppc_asm.h>
+
+	.text
+
+/*
+ * void ppc44x_reset_system(char *cmd)
+ *
+ * At present, this routine just applies a system reset.
+ */
+_GLOBAL(ppc44x_reset_system)
+	mfspr	r13,SPRN_DBCR0
+	oris	r13,r13,DBCR0_RST_SYSTEM@h
+	mtspr	SPRN_DBCR0,r13
+	b	.			/* Just in case the reset doesn't work */

arch/powerpc/platforms/44x/44x.h new file +6 -0

Index: working-2.6/arch/powerpc/platforms/44x/44x.h
===================================================================
@@ -0,0 +1,6 @@
+#ifndef __POWERPC_PLATFORMS_44X_44X_H
+#define __POWERPC_PLATFORMS_44X_44X_H
+
+extern void ppc44x_reset_system(char *cmd);
+
+#endif /* __POWERPC_PLATFORMS_44X_44X_H */

arch/powerpc/kernel/head_44x.S +0 ~~-10~~

Index: working-2.6/arch/powerpc/kernel/head_44x.S
===================================================================
@@ -709,16 +709,6 @@ _GLOBAL(giveup_fpu)
 	blr
 #endif
 
-/*
- * extern void abort(void)
- *
- * At present, this routine just applies a system reset.
- */
-_GLOBAL(abort)
-        mfspr   r13,SPRN_DBCR0
-        oris    r13,r13,DBCR0_RST_SYSTEM@h
-        mtspr   SPRN_DBCR0,r13
-
 _GLOBAL(set_context)
 
 #ifdef CONFIG_BDI_SWITCH

arch/powerpc/platforms/44x/Makefile new file +1 -0

Index: working-2.6/arch/powerpc/platforms/44x/Makefile
===================================================================
@@ -0,0 +1 @@
+obj-$(CONFIG_44x)	:= misc_44x.o

arch/powerpc/platforms/Makefile +2 -1

Index: working-2.6/arch/powerpc/platforms/Makefile
===================================================================
@@ -6,7 +6,8 @@ obj-$(CONFIG_PPC_PMAC)		+= powermac/
 endif
 endif
 obj-$(CONFIG_PPC_CHRP)		+= chrp/
-obj-$(CONFIG_4xx)		+= 4xx/
+#obj-$(CONFIG_4xx)		+= 4xx/
+obj-$(CONFIG_44x)		+= 44x/
 obj-$(CONFIG_PPC_MPC52xx)	+= 52xx/
 obj-$(CONFIG_PPC_8xx)		+= 8xx/
 obj-$(CONFIG_PPC_82xx)		+= 82xx/

David Gibson

author

2007-05-08 02:59 UTC #4 lore raw

PATCH 4/7 Add device tree for Ebony

In reply to David Gibson

Add a device tree for the Ebony evaluation board (440GP based). This tree is not complete or finalized. This tree needs a version of dtc recent enough to include reference-to-labels to process.

Signed-off-by David Gibson <[email protected]>

---

 arch/powerpc/boot/dts/ebony.dts |  307 ++++++++++++++++++++++++++++++++++++++++
 1 file changed, 307 insertions(+)

arch/powerpc/boot/dts/ebony.dts new file +307 -0

Index: working-2.6/arch/powerpc/boot/dts/ebony.dts
===================================================================
@@ -0,0 +1,307 @@
+/*
+ * Device Tree Source for IBM Ebony
+ *
+ * Copyright (c) 2006, 2007 IBM Corp.
+ * Josh Boyer <[email protected]>, David Gibson <[email protected]>
+ *
+ * FIXME: Draft only!
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without
+ * any warranty of any kind, whether express or implied.
+ *
+ * To build:
+ *   dtc -I dts -O asm -o ebony.S -b 0 ebony.dts
+ *   dtc -I dts -O dtb -o ebony.dtb -b 0 ebony.dts
+ */
+
+/ {
+	#address-cells = <2>;
+	#size-cells = <1>;
+	model = "Ebony";
+	compatible = "Ebony";
+	dcr-parent = <&/cpus/PowerPC,440GP@0>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		PowerPC,440GP@0 {
+			device_type = "cpu";
+			reg = <0>;
+			clock-frequency = <0>; // Filled in by zImage
+			timebase-frequency = <0>; // Filled in by zImage
+			i-cache-line-size = <32>;
+			d-cache-line-size = <32>;
+			i-cache-size = <0>;
+			d-cache-size = <0>;
+			dcr-controller;
+			dcr-access-method = "native";
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0 0 0>; // Filled in by zImage
+	};
+
+	UIC0: interrupt-controller0 {
+		device_type = "ibm,uic";
+		compatible = "ibm,uic-440gp", "ibm,uic";
+		interrupt-controller;
+		cell-index = <0>;
+		dcr-reg = <0c0 009>;
+		#address-cells = <0>;
+		#size-cells = <0>;
+		#interrupt-cells = <2>;
+
+	};
+
+	UIC1: interrupt-controller1 {
+		device_type = "ibm,uic";
+		compatible = "ibm,uic-440gp", "ibm,uic";
+		interrupt-controller;
+		cell-index = <1>;
+		dcr-reg = <0d0 009>;
+		#address-cells = <0>;
+		#size-cells = <0>;
+		#interrupt-cells = <2>;
+		interrupts = <1e 4 1f 4>; /* cascade */
+		interrupt-parent = <&UIC0>;
+	};
+
+	CPC0: cpc {
+		device_type = "ibm,cpc";
+		compatible = "ibm,cpc-440gp";
+		dcr-reg = <0b0 003 0e0 010>;
+		// FIXME: anything else?
+	};
+
+	plb {
+		device_type = "ibm,plb";
+		compatible = "ibm,plb-440gp", "ibm,plb4";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges;
+		clock-frequency = <0>; // Filled in by zImage
+
+		SDRAM0: sdram {
+			device_type = "memory-controller";
+			compatible = "ibm,sdram-440gp", "ibm,sdram";
+			dcr-reg = <010 2>;
+			// FIXME: anything else?
+		};
+
+		DMA0: dma {
+			// FIXME: ???
+			device_type = "ibm,dma-4xx";
+			compatible = "ibm,dma-440gp", "ibm,dma-4xx";
+			dcr-reg = <100 027>;
+		};
+
+		MAL0: mcmal {
+			device_type = "mcmal-dma";
+			compatible = "ibm,mcmal-440gp", "ibm,mcmal";
+			dcr-reg = <180 62>;
+			num-tx-chans = <4>;
+			num-rx-chans = <4>;
+			interrupt-parent = <&MAL0>;
+			interrupts = <0 1 2 3 4>;
+			#interrupt-cells = <1>;
+			#address-cells = <0>;
+			#size-cells = <0>;
+			interrupt-map = </*TXEOB*/ 0 &UIC0 a 4
+					 /*RXEOB*/ 1 &UIC0 b 4
+					 /*SERR*/  2 &UIC1 0 4
+					 /*TXDE*/  3 &UIC1 1 4
+					 /*RXDE*/  4 &UIC1 2 4>;
+			interrupt-map-mask = <ffffffff>;
+		};
+
+		POB0: opb {
+			device_type = "ibm,opb";
+			compatible = "ibm,opb-440gp", "ibm,opb";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			/* Wish there was a nicer way of specifying a full 32-bit
+			   range */
+			ranges = <00000000 1 00000000 80000000
+				  80000000 1 80000000 80000000>;
+			dcr-reg = <090 00b>;
+			interrupt-parent = <&UIC1>;
+			interrupts = <7 4>;
+			clock-frequency = <0>; // Filled in by zImage
+
+			EBC0: ebc {
+				device_type = "ibm,ebc";
+				compatible = "ibm,ebc-440gp";
+				dcr-reg = <012 2>;
+				#address-cells = <2>;
+				#size-cells = <1>;
+				clock-frequency = <0>; // Filled in by zImage
+				ranges = <0 00000000 fff00000 100000
+					  1 00000000 48000000 100000
+					  2 00000000 ff800000 400000
+					  3 00000000 48200000 100000
+					  7 00000000 48300000 100000>;
+				interrupts = <5 4>;
+				interrupt-parent = <&UIC1>;
+
+				small-flash@0,0 {
+					device_type = "rom";
+					compatible = "direct-mapped";
+					probe-type = "JEDEC";
+					bank-width = <1>;
+					partitions = <0 80000>;
+					partition-names = "OpenBIOS";
+					reg = <0 80000 80000>;
+				};
+
+				ds1743@1,0 {
+					/* NVRAM & RTC */
+					device_type = "nvram";
+					compatible = "ds1743";
+					reg = <1 0 2000>;
+				};
+
+				large-flash@2,0 {
+					device_type = "rom";
+					compatible = "direct-mapped";
+					probe-type = "JEDEC";
+					bank-width = <1>;
+					partitions = <0 380000
+						      280000 80000>;
+					partition-names = "fs", "firmware";
+					reg = <2 0 400000>;
+				};
+
+				ir@3,0 {
+					reg = <3 0 10>;
+				};
+
+				fpga@7,0 {
+					compatible = "Ebony-FPGA";
+					reg = <7 0 10>;
+				};
+			};
+
+			UART0: serial@40000200 {
+				device_type = "serial";
+				compatible = "ns16550";
+				reg = <40000200 8>;
+				virtual-reg = <e0000200>;
+				clock-frequency = <A8C000>;
+				current-speed = <2580>;
+				interrupt-parent = <&UIC0>;
+				interrupts = <0 4>;
+			};
+
+			UART1: serial@40000300 {
+				device_type = "serial";
+				compatible = "ns16550";
+				reg = <40000300 8>;
+				virtual-reg = <e0000300>;
+				clock-frequency = <A8C000>;
+				current-speed = <2580>;
+				interrupt-parent = <&UIC0>;
+				interrupts = <1 4>;
+			};
+
+			IIC0: i2c@40000400 {
+				/* FIXME */
+				device_type = "i2c";
+				compatible = "ibm,iic-440gp", "ibm,iic";
+				reg = <40000400 14>;
+				interrupt-parent = <&UIC0>;
+				interrupts = <2 4>;
+			};
+			IIC1: i2c@40000500 {
+				/* FIXME */
+				device_type = "i2c";
+				compatible = "ibm,iic-440gp", "ibm,iic";
+				reg = <40000500 14>;
+				interrupt-parent = <&UIC0>;
+				interrupts = <3 4>;
+			};
+
+			GPIO0: gpio@40000700 {
+				/* FIXME */
+				device_type = "gpio";
+				compatible = "ibm,gpio-440gp";
+				reg = <40000700 20>;
+			};
+
+			ZMII0: emac-zmii@40000780 {
+				device_type = "emac-zmii";
+				compatible = "ibm,zmii-440gp", "ibm,zmii";
+				reg = <40000780 c>;
+			};
+
+			EMAC0: ethernet@40000800 {
+				linux,network-index = <0>;
+				device_type = "network";
+				compatible = "ibm,emac-440gp", "ibm,emac";
+				interrupt-parent = <&UIC1>;
+				interrupts = <1c 4 1d 4>;
+				reg = <40000800 70>;
+				local-mac-address = [000000000000]; // Filled in by zImage
+				mal-device = <&MAL0>;
+				mal-tx-channel = <0 1>;
+				mal-rx-channel = <0>;
+				cell-index = <0>;
+				max-frame-size = <5dc>;
+				rx-fifo-size = <1000>;
+				tx-fifo-size = <800>;
+				phy-mode = "rmii";
+				phy-map = <00000001>;
+				zmii-device = <&ZMII0>;
+				zmii-channel = <0>;
+			};
+			EMAC1: ethernet@40000900 {
+				linux,network-index = <1>;
+				device_type = "network";
+				compatible = "ibm,emac-440gp", "ibm,emac";
+				interrupt-parent = <&UIC1>;
+				interrupts = <1e 4 1f 4>;
+				reg = <40000900 70>;
+				local-mac-address = [000000000000]; // Filled in by zImage
+				mal-device = <&MAL0>;
+				mal-tx-channel = <2 3>;
+				mal-rx-channel = <1>;
+				cell-index = <1>;
+				max-frame-size = <5dc>;
+				rx-fifo-size = <1000>;
+				tx-fifo-size = <800>;
+				phy-mode = "rmii";
+				phy-map = <00000001>;
+				zmii-device = <&ZMII0>;
+				zmii-channel = <1>;
+			};
+
+
+			GPT0: gpt@40000a00 {
+				/* FIXME */
+				reg = <40000a00 d4>;
+				interrupt-parent = <&UIC0>;
+				interrupts = <12 4 13 4 14 4 15 4 16 4>;
+			};
+
+		};
+
+		PCIX0: pci@1234 {
+			device_type = "pci";
+			/* FIXME */
+			reg = <2 0ec00000 8
+			       2 0ec80000 f0
+			       2 0ec80100 fc>;
+		};
+	};
+
+	chosen {
+		linux,stdout-path = "/plb/opb/serial@40000200";
+//		linux,initrd-start = <0>; /* FIXME */
+//		linux,initrd-end = <0>;
+//		bootargs = "";
+	};
+};
+

Olof Johansson

2007-05-08 03:29 UTC #5 lore raw

Re: [PATCH 4/7] Add device tree for Ebony

Quoted 15 lines · David Gibson

Add a device tree for the Ebony evaluation board (440GP based). This tree is not complete or finalized. This tree needs a version of dtc recent enough to include reference-to-labels to process.
Signed-off-by David Gibson <[email protected]>
---
 arch/powerpc/boot/dts/ebony.dts |  307 ++++++++++++++++++++++++++++++++++++++++
 1 file changed, 307 insertions(+)
Index: working-2.6/arch/powerpc/boot/dts/ebony.dts
===================================================================

arch/powerpc/boot/dts/ebony.dts line 5

Quoted 5 lines

arch/powerpc/boot/dts/ebony.dts new file +5 -0

@@ -0,0 +1,307 @@
+/ {
+	#address-cells = <2>;
+	#size-cells = <1>;
+	model = "Ebony";
+	compatible = "Ebony";

ibm,ebony? See the discussion on the Holly port.

David Gibson

author

2007-05-08 04:09 UTC #6 lore raw

Re: [PATCH 4/7] Add device tree for Ebony

Quoted 11 lines · Olof Johansson

Quoted 10 lines · David Gibson
Add a device tree for the Ebony evaluation board (440GP based). This tree is not complete or finalized. This tree needs a version of dtc recent enough to include reference-to-labels to process.
Signed-off-by David Gibson <[email protected]>
---
 arch/powerpc/boot/dts/ebony.dts |  307 ++++++++++++++++++++++++++++++++++++++++
 1 file changed, 307 insertions(+)

Quoted 12 lines

arch/powerpc/boot/dts/ebony.dts line 5
Quoted 10 lines
Index: working-2.6/arch/powerpc/boot/dts/ebony.dts
===================================================================
arch/powerpc/boot/dts/ebony.dts new file +5 -0
@@ -0,0 +1,307 @@
+/ {
+	#address-cells = <2>;
+	#size-cells = <1>;
+	model = "Ebony";
+	compatible = "Ebony";
ibm,ebony? See the discussion on the Holly port.

Yeah, fair enough. Revised patch below. Revised patch for the support code to recognize the changed string coming.

Add device tree for Ebony

Add a device tree for the Ebony evaluation board (440GP based). This tree is not complete or finalized. This tree needs a version of dtc recent enough to include reference-to-labels to process.

Signed-off-by David Gibson <[email protected]>

arch/powerpc/boot/dts/ebony.dts new file +307 -0

Index: working-2.6/arch/powerpc/boot/dts/ebony.dts
===================================================================
@@ -0,0 +1,307 @@
+/*
+ * Device Tree Source for IBM Ebony
+ *
+ * Copyright (c) 2006, 2007 IBM Corp.
+ * Josh Boyer <[email protected]>, David Gibson <[email protected]>
+ *
+ * FIXME: Draft only!
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without
+ * any warranty of any kind, whether express or implied.
+ *
+ * To build:
+ *   dtc -I dts -O asm -o ebony.S -b 0 ebony.dts
+ *   dtc -I dts -O dtb -o ebony.dtb -b 0 ebony.dts
+ */
+
+/ {
+	#address-cells = <2>;
+	#size-cells = <1>;
+	model = "ibm,ebony";
+	compatible = "ibm,ebony";
+	dcr-parent = <&/cpus/PowerPC,440GP@0>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		PowerPC,440GP@0 {
+			device_type = "cpu";
+			reg = <0>;
+			clock-frequency = <0>; // Filled in by zImage
+			timebase-frequency = <0>; // Filled in by zImage
+			i-cache-line-size = <32>;
+			d-cache-line-size = <32>;
+			i-cache-size = <0>;
+			d-cache-size = <0>;
+			dcr-controller;
+			dcr-access-method = "native";
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0 0 0>; // Filled in by zImage
+	};
+
+	UIC0: interrupt-controller0 {
+		device_type = "ibm,uic";
+		compatible = "ibm,uic-440gp", "ibm,uic";
+		interrupt-controller;
+		cell-index = <0>;
+		dcr-reg = <0c0 009>;
+		#address-cells = <0>;
+		#size-cells = <0>;
+		#interrupt-cells = <2>;
+
+	};
+
+	UIC1: interrupt-controller1 {
+		device_type = "ibm,uic";
+		compatible = "ibm,uic-440gp", "ibm,uic";
+		interrupt-controller;
+		cell-index = <1>;
+		dcr-reg = <0d0 009>;
+		#address-cells = <0>;
+		#size-cells = <0>;
+		#interrupt-cells = <2>;
+		interrupts = <1e 4 1f 4>; /* cascade */
+		interrupt-parent = <&UIC0>;
+	};
+
+	CPC0: cpc {
+		device_type = "ibm,cpc";
+		compatible = "ibm,cpc-440gp";
+		dcr-reg = <0b0 003 0e0 010>;
+		// FIXME: anything else?
+	};
+
+	plb {
+		device_type = "ibm,plb";
+		compatible = "ibm,plb-440gp", "ibm,plb4";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges;
+		clock-frequency = <0>; // Filled in by zImage
+
+		SDRAM0: sdram {
+			device_type = "memory-controller";
+			compatible = "ibm,sdram-440gp", "ibm,sdram";
+			dcr-reg = <010 2>;
+			// FIXME: anything else?
+		};
+
+		DMA0: dma {
+			// FIXME: ???
+			device_type = "ibm,dma-4xx";
+			compatible = "ibm,dma-440gp", "ibm,dma-4xx";
+			dcr-reg = <100 027>;
+		};
+
+		MAL0: mcmal {
+			device_type = "mcmal-dma";
+			compatible = "ibm,mcmal-440gp", "ibm,mcmal";
+			dcr-reg = <180 62>;
+			num-tx-chans = <4>;
+			num-rx-chans = <4>;
+			interrupt-parent = <&MAL0>;
+			interrupts = <0 1 2 3 4>;
+			#interrupt-cells = <1>;
+			#address-cells = <0>;
+			#size-cells = <0>;
+			interrupt-map = </*TXEOB*/ 0 &UIC0 a 4
+					 /*RXEOB*/ 1 &UIC0 b 4
+					 /*SERR*/  2 &UIC1 0 4
+					 /*TXDE*/  3 &UIC1 1 4
+					 /*RXDE*/  4 &UIC1 2 4>;
+			interrupt-map-mask = <ffffffff>;
+		};
+
+		POB0: opb {
+			device_type = "ibm,opb";
+			compatible = "ibm,opb-440gp", "ibm,opb";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			/* Wish there was a nicer way of specifying a full 32-bit
+			   range */
+			ranges = <00000000 1 00000000 80000000
+				  80000000 1 80000000 80000000>;
+			dcr-reg = <090 00b>;
+			interrupt-parent = <&UIC1>;
+			interrupts = <7 4>;
+			clock-frequency = <0>; // Filled in by zImage
+
+			EBC0: ebc {
+				device_type = "ibm,ebc";
+				compatible = "ibm,ebc-440gp";
+				dcr-reg = <012 2>;
+				#address-cells = <2>;
+				#size-cells = <1>;
+				clock-frequency = <0>; // Filled in by zImage
+				ranges = <0 00000000 fff00000 100000
+					  1 00000000 48000000 100000
+					  2 00000000 ff800000 400000
+					  3 00000000 48200000 100000
+					  7 00000000 48300000 100000>;
+				interrupts = <5 4>;
+				interrupt-parent = <&UIC1>;
+
+				small-flash@0,0 {
+					device_type = "rom";
+					compatible = "direct-mapped";
+					probe-type = "JEDEC";
+					bank-width = <1>;
+					partitions = <0 80000>;
+					partition-names = "OpenBIOS";
+					reg = <0 80000 80000>;
+				};
+
+				ds1743@1,0 {
+					/* NVRAM & RTC */
+					device_type = "nvram";
+					compatible = "ds1743";
+					reg = <1 0 2000>;
+				};
+
+				large-flash@2,0 {
+					device_type = "rom";
+					compatible = "direct-mapped";
+					probe-type = "JEDEC";
+					bank-width = <1>;
+					partitions = <0 380000
+						      280000 80000>;
+					partition-names = "fs", "firmware";
+					reg = <2 0 400000>;
+				};
+
+				ir@3,0 {
+					reg = <3 0 10>;
+				};
+
+				fpga@7,0 {
+					compatible = "Ebony-FPGA";
+					reg = <7 0 10>;
+				};
+			};
+
+			UART0: serial@40000200 {
+				device_type = "serial";
+				compatible = "ns16550";
+				reg = <40000200 8>;
+				virtual-reg = <e0000200>;
+				clock-frequency = <A8C000>;
+				current-speed = <2580>;
+				interrupt-parent = <&UIC0>;
+				interrupts = <0 4>;
+			};
+
+			UART1: serial@40000300 {
+				device_type = "serial";
+				compatible = "ns16550";
+				reg = <40000300 8>;
+				virtual-reg = <e0000300>;
+				clock-frequency = <A8C000>;
+				current-speed = <2580>;
+				interrupt-parent = <&UIC0>;
+				interrupts = <1 4>;
+			};
+
+			IIC0: i2c@40000400 {
+				/* FIXME */
+				device_type = "i2c";
+				compatible = "ibm,iic-440gp", "ibm,iic";
+				reg = <40000400 14>;
+				interrupt-parent = <&UIC0>;
+				interrupts = <2 4>;
+			};
+			IIC1: i2c@40000500 {
+				/* FIXME */
+				device_type = "i2c";
+				compatible = "ibm,iic-440gp", "ibm,iic";
+				reg = <40000500 14>;
+				interrupt-parent = <&UIC0>;
+				interrupts = <3 4>;
+			};
+
+			GPIO0: gpio@40000700 {
+				/* FIXME */
+				device_type = "gpio";
+				compatible = "ibm,gpio-440gp";
+				reg = <40000700 20>;
+			};
+
+			ZMII0: emac-zmii@40000780 {
+				device_type = "emac-zmii";
+				compatible = "ibm,zmii-440gp", "ibm,zmii";
+				reg = <40000780 c>;
+			};
+
+			EMAC0: ethernet@40000800 {
+				linux,network-index = <0>;
+				device_type = "network";
+				compatible = "ibm,emac-440gp", "ibm,emac";
+				interrupt-parent = <&UIC1>;
+				interrupts = <1c 4 1d 4>;
+				reg = <40000800 70>;
+				local-mac-address = [000000000000]; // Filled in by zImage
+				mal-device = <&MAL0>;
+				mal-tx-channel = <0 1>;
+				mal-rx-channel = <0>;
+				cell-index = <0>;
+				max-frame-size = <5dc>;
+				rx-fifo-size = <1000>;
+				tx-fifo-size = <800>;
+				phy-mode = "rmii";
+				phy-map = <00000001>;
+				zmii-device = <&ZMII0>;
+				zmii-channel = <0>;
+			};
+			EMAC1: ethernet@40000900 {
+				linux,network-index = <1>;
+				device_type = "network";
+				compatible = "ibm,emac-440gp", "ibm,emac";
+				interrupt-parent = <&UIC1>;
+				interrupts = <1e 4 1f 4>;
+				reg = <40000900 70>;
+				local-mac-address = [000000000000]; // Filled in by zImage
+				mal-device = <&MAL0>;
+				mal-tx-channel = <2 3>;
+				mal-rx-channel = <1>;
+				cell-index = <1>;
+				max-frame-size = <5dc>;
+				rx-fifo-size = <1000>;
+				tx-fifo-size = <800>;
+				phy-mode = "rmii";
+				phy-map = <00000001>;
+				zmii-device = <&ZMII0>;
+				zmii-channel = <1>;
+			};
+
+
+			GPT0: gpt@40000a00 {
+				/* FIXME */
+				reg = <40000a00 d4>;
+				interrupt-parent = <&UIC0>;
+				interrupts = <12 4 13 4 14 4 15 4 16 4>;
+			};
+
+		};
+
+		PCIX0: pci@1234 {
+			device_type = "pci";
+			/* FIXME */
+			reg = <2 0ec00000 8
+			       2 0ec80000 f0
+			       2 0ec80100 fc>;
+		};
+	};
+
+	chosen {
+		linux,stdout-path = "/plb/opb/serial@40000200";
+//		linux,initrd-start = <0>; /* FIXME */
+//		linux,initrd-end = <0>;
+//		bootargs = "";
+	};
+};
+

Signature · 4 lines

David Gibson			| I'll have my music baroque, and my code
david AT gibson.dropbear.id.au	| minimalist, thank you.  NOT _the_ _other_
				| _way_ _around_!
http://www.ozlabs.org/~dgibson

David Gibson

author

2007-05-08 02:59 UTC #7 lore raw

PATCH 5/7 Support for the Ebony 440GP reference board in arch/powerpc

In reply to David Gibson

This patch adds platform support code for the Ebony (440GP) evaluation board. This includes both code in arch/powerpc/platforms/44x for board initialization, and zImage wrapper code to correctly tweak the flattened device tree based on information from the firmware. The zImage supports both IBM OpenBIOS (aka "treeboot") and old versions of uboot which don't support a flattened device tree.

Signed-off-by David Gibson <[email protected]>

---

 arch/powerpc/Kconfig                 |    8 
 arch/powerpc/boot/44x.c              |   40 +
 arch/powerpc/boot/44x.h              |   16 
 arch/powerpc/boot/Makefile           |   18 
 arch/powerpc/boot/cuboot-ebony.c     |   42 +
 arch/powerpc/boot/dcr.h              |   87 +++
 arch/powerpc/boot/ebony.c            |  129 ++++
 arch/powerpc/boot/mktree.c           |   10 
 arch/powerpc/boot/treeboot-ebony.c   |   34 +
 arch/powerpc/boot/wrapper            |    8 
 arch/powerpc/configs/ebony_defconfig |  905 +++++++++++++++++++++++++++++++++++
 arch/powerpc/platforms/44x/Kconfig   |   56 ++
 arch/powerpc/platforms/44x/Makefile  |    1 
 arch/powerpc/platforms/44x/ebony.c   |   73 ++
 arch/powerpc/platforms/Kconfig       |    1 
 15 files changed, 1417 insertions(+), 11 deletions(-)

arch/powerpc/configs/ebony_defconfig new file +905 -0

Index: working-2.6/arch/powerpc/configs/ebony_defconfig
===================================================================
@@ -0,0 +1,905 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.21
+# Fri May  4 13:47:08 2007
+#
+# CONFIG_PPC64 is not set
+CONFIG_PPC32=y
+CONFIG_PPC_MERGE=y
+CONFIG_MMU=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_IRQ_PER_CPU=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_ARCH_HAS_ILOG2_U32=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+CONFIG_PPC=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_GENERIC_NVRAM=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+CONFIG_PPC_OF=y
+# CONFIG_PPC_UDBG_16550 is not set
+# CONFIG_GENERIC_TBSYNC is not set
+CONFIG_AUDIT_ARCH=y
+CONFIG_GENERIC_BUG=y
+# CONFIG_DEFAULT_UIMAGE is not set
+
+#
+# Processor support
+#
+# CONFIG_CLASSIC32 is not set
+# CONFIG_PPC_82xx is not set
+# CONFIG_PPC_83xx is not set
+# CONFIG_PPC_85xx is not set
+# CONFIG_PPC_86xx is not set
+# CONFIG_PPC_8xx is not set
+# CONFIG_40x is not set
+CONFIG_44x=y
+# CONFIG_E200 is not set
+CONFIG_PPC_DCR_NATIVE=y
+# CONFIG_PPC_DCR_MMIO is not set
+CONFIG_PPC_DCR=y
+CONFIG_4xx=y
+CONFIG_BOOKE=y
+CONFIG_PTE_64BIT=y
+CONFIG_PHYS_64BIT=y
+CONFIG_NOT_COHERENT_CACHE=y
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+
+#
+# Code maturity level options
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+
+#
+# General setup
+#
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+# CONFIG_IPC_NS is not set
+CONFIG_SYSVIPC_SYSCTL=y
+CONFIG_POSIX_MQUEUE=y
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_UTS_NS is not set
+# CONFIG_AUDIT is not set
+# CONFIG_IKCONFIG is not set
+CONFIG_SYSFS_DEPRECATED=y
+# CONFIG_RELAY is not set
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_INITRAMFS_SOURCE=""
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SYSCTL=y
+CONFIG_EMBEDDED=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS=y
+CONFIG_KALLSYMS_ALL=y
+CONFIG_KALLSYMS_EXTRA_PASS=y
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_EPOLL=y
+CONFIG_SHMEM=y
+CONFIG_SLAB=y
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_RT_MUTEXES=y
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=0
+# CONFIG_SLOB is not set
+
+#
+# Loadable module support
+#
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_MODULE_FORCE_UNLOAD is not set
+# CONFIG_MODVERSIONS is not set
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+CONFIG_KMOD=y
+
+#
+# Block layer
+#
+CONFIG_BLOCK=y
+CONFIG_LBD=y
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+CONFIG_DEFAULT_AS=y
+# CONFIG_DEFAULT_DEADLINE is not set
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="anticipatory"
+
+#
+# Platform support
+#
+# CONFIG_PPC_MPC52xx is not set
+# CONFIG_PPC_MPC5200 is not set
+# CONFIG_PPC_CELL is not set
+# CONFIG_PPC_CELL_NATIVE is not set
+# CONFIG_PQ2ADS is not set
+CONFIG_EBONY=y
+CONFIG_440GP=y
+# CONFIG_MPIC is not set
+# CONFIG_MPIC_WEIRD is not set
+# CONFIG_PPC_I8259 is not set
+# CONFIG_PPC_RTAS is not set
+# CONFIG_MMIO_NVRAM is not set
+# CONFIG_PPC_MPC106 is not set
+# CONFIG_PPC_970_NAP is not set
+# CONFIG_PPC_INDIRECT_IO is not set
+# CONFIG_GENERIC_IOMAP is not set
+# CONFIG_CPU_FREQ is not set
+# CONFIG_CPM2 is not set
+
+#
+# Kernel options
+#
+# CONFIG_HIGHMEM is not set
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_250=y
+# CONFIG_HZ_300 is not set
+# CONFIG_HZ_1000 is not set
+CONFIG_HZ=250
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_BINFMT_ELF=y
+# CONFIG_BINFMT_MISC is not set
+CONFIG_MATH_EMULATION=y
+CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
+CONFIG_ARCH_FLATMEM_ENABLE=y
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4
+CONFIG_RESOURCES_64BIT=y
+CONFIG_ZONE_DMA_FLAG=1
+CONFIG_PROC_DEVICETREE=y
+# CONFIG_CMDLINE_BOOL is not set
+CONFIG_SECCOMP=y
+CONFIG_WANT_DEVICE_TREE=y
+CONFIG_DEVICE_TREE="ebony.dts"
+CONFIG_ISA_DMA_API=y
+
+#
+# Bus options
+#
+CONFIG_ZONE_DMA=y
+CONFIG_PPC_INDIRECT_PCI=y
+# CONFIG_PPC_INDIRECT_PCI_BE is not set
+CONFIG_PCI=y
+CONFIG_PCI_DOMAINS=y
+# CONFIG_PCIEPORTBUS is not set
+# CONFIG_PCI_DEBUG is not set
+
+#
+# PCCARD (PCMCIA/CardBus) support
+#
+# CONFIG_PCCARD is not set
+
+#
+# PCI Hotplug Support
+#
+# CONFIG_HOTPLUG_PCI is not set
+
+#
+# Advanced setup
+#
+# CONFIG_ADVANCED_OPTIONS is not set
+
+#
+# Default settings for advanced configuration options are used
+#
+CONFIG_HIGHMEM_START=0xfe000000
+CONFIG_LOWMEM_SIZE=0x30000000
+CONFIG_KERNEL_START=0xc0000000
+CONFIG_TASK_SIZE=0x80000000
+CONFIG_CONSISTENT_START=0xff100000
+CONFIG_CONSISTENT_SIZE=0x00200000
+CONFIG_BOOT_LOAD=0x01000000
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+# CONFIG_IP_MULTICAST is not set
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_ARPD is not set
+# CONFIG_SYN_COOKIES is not set
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_INET6_XFRM_TUNNEL is not set
+# CONFIG_INET6_TUNNEL is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+
+#
+# DCCP Configuration (EXPERIMENTAL)
+#
+# CONFIG_IP_DCCP is not set
+
+#
+# SCTP Configuration (EXPERIMENTAL)
+#
+# CONFIG_IP_SCTP is not set
+
+#
+# TIPC Configuration (EXPERIMENTAL)
+#
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+
+#
+# QoS and/or fair queueing
+#
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_IEEE80211 is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+CONFIG_FW_LOADER=y
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+
+#
+# Connector - unified userspace <-> kernelspace linker
+#
+CONFIG_CONNECTOR=y
+CONFIG_PROC_EVENTS=y
+# CONFIG_MTD is not set
+
+#
+# Parallel port support
+#
+# CONFIG_PARPORT is not set
+
+#
+# Plug and Play support
+#
+# CONFIG_PNPACPI is not set
+
+#
+# Block devices
+#
+# CONFIG_BLK_DEV_FD is not set
+# CONFIG_BLK_CPQ_DA is not set
+# CONFIG_BLK_CPQ_CISS_DA is not set
+# CONFIG_BLK_DEV_DAC960 is not set
+# CONFIG_BLK_DEV_UMEM is not set
+# CONFIG_BLK_DEV_COW_COMMON is not set
+# CONFIG_BLK_DEV_LOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_SX8 is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=35000
+CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+
+#
+# Misc devices
+#
+# CONFIG_SGI_IOC4 is not set
+# CONFIG_TIFM_CORE is not set
+
+#
+# ATA/ATAPI/MFM/RLL support
+#
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+# CONFIG_SCSI is not set
+# CONFIG_SCSI_NETLINK is not set
+
+#
+# Serial ATA (prod) and Parallel ATA (experimental) drivers
+#
+# CONFIG_ATA is not set
+
+#
+# Multi-device support (RAID and LVM)
+#
+# CONFIG_MD is not set
+
+#
+# Fusion MPT device support
+#
+# CONFIG_FUSION is not set
+
+#
+# IEEE 1394 (FireWire) support
+#
+# CONFIG_IEEE1394 is not set
+
+#
+# I2O device support
+#
+# CONFIG_I2O is not set
+# CONFIG_MACINTOSH_DRIVERS is not set
+
+#
+# Network device support
+#
+CONFIG_NETDEVICES=y
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+
+#
+# ARCnet devices
+#
+# CONFIG_ARCNET is not set
+
+#
+# PHY device support
+#
+
+#
+# Ethernet (10 or 100Mbit)
+#
+# CONFIG_NET_ETHERNET is not set
+CONFIG_IBM_NEW_EMAC=y
+CONFIG_IBM_NEW_EMAC_RXB=128
+CONFIG_IBM_NEW_EMAC_TXB=64
+CONFIG_IBM_NEW_EMAC_POLL_WEIGHT=32
+CONFIG_IBM_NEW_EMAC_RX_COPY_THRESHOLD=256
+CONFIG_IBM_NEW_EMAC_RX_SKB_HEADROOM=0
+# CONFIG_IBM_NEW_EMAC_DEBUG is not set
+CONFIG_IBM_NEW_EMAC_ZMII=y
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+
+#
+# Ethernet (1000 Mbit)
+#
+# CONFIG_ACENIC is not set
+# CONFIG_DL2K is not set
+# CONFIG_E1000 is not set
+# CONFIG_NS83820 is not set
+# CONFIG_HAMACHI is not set
+# CONFIG_YELLOWFIN is not set
+# CONFIG_R8169 is not set
+# CONFIG_SIS190 is not set
+# CONFIG_SKGE is not set
+# CONFIG_SKY2 is not set
+# CONFIG_SK98LIN is not set
+# CONFIG_TIGON3 is not set
+# CONFIG_BNX2 is not set
+# CONFIG_QLA3XXX is not set
+# CONFIG_ATL1 is not set
+
+#
+# Ethernet (10000 Mbit)
+#
+# CONFIG_CHELSIO_T1 is not set
+# CONFIG_CHELSIO_T3 is not set
+# CONFIG_IXGB is not set
+# CONFIG_S2IO is not set
+# CONFIG_MYRI10GE is not set
+# CONFIG_NETXEN_NIC is not set
+
+#
+# Token Ring devices
+#
+# CONFIG_TR is not set
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+
+#
+# Wan interfaces
+#
+# CONFIG_WAN is not set
+# CONFIG_FDDI is not set
+# CONFIG_HIPPI is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_SHAPER is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+
+#
+# ISDN subsystem
+#
+# CONFIG_ISDN is not set
+
+#
+# Telephony Support
+#
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+# CONFIG_INPUT is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+# CONFIG_VT is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+# CONFIG_SERIAL_8250_PCI is not set
+CONFIG_SERIAL_8250_NR_UARTS=4
+CONFIG_SERIAL_8250_RUNTIME_UARTS=4
+CONFIG_SERIAL_8250_EXTENDED=y
+# CONFIG_SERIAL_8250_MANY_PORTS is not set
+CONFIG_SERIAL_8250_SHARE_IRQ=y
+# CONFIG_SERIAL_8250_DETECT_IRQ is not set
+# CONFIG_SERIAL_8250_RSA is not set
+
+#
+# Non-8250 serial port support
+#
+# CONFIG_SERIAL_UARTLITE is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+# CONFIG_SERIAL_JSM is not set
+CONFIG_SERIAL_OF_PLATFORM=y
+CONFIG_UNIX98_PTYS=y
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+
+#
+# IPMI
+#
+# CONFIG_IPMI_HANDLER is not set
+
+#
+# Watchdog Cards
+#
+# CONFIG_WATCHDOG is not set
+# CONFIG_HW_RANDOM is not set
+# CONFIG_NVRAM is not set
+# CONFIG_GEN_RTC is not set
+# CONFIG_DTLK is not set
+# CONFIG_R3964 is not set
+# CONFIG_APPLICOM is not set
+# CONFIG_AGP is not set
+# CONFIG_DRM is not set
+# CONFIG_RAW_DRIVER is not set
+
+#
+# TPM devices
+#
+# CONFIG_TCG_TPM is not set
+
+#
+# I2C support
+#
+# CONFIG_I2C is not set
+
+#
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+
+#
+# Dallas's 1-wire bus
+#
+# CONFIG_W1 is not set
+
+#
+# Hardware Monitoring support
+#
+# CONFIG_HWMON is not set
+# CONFIG_HWMON_VID is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_SM501 is not set
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+
+#
+# Digital Video Broadcasting Devices
+#
+# CONFIG_DVB is not set
+
+#
+# Graphics support
+#
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+# CONFIG_FB is not set
+# CONFIG_FB_IBM_GXT4500 is not set
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+
+#
+# USB support
+#
+CONFIG_USB_ARCH_HAS_HCD=y
+CONFIG_USB_ARCH_HAS_OHCI=y
+CONFIG_USB_ARCH_HAS_EHCI=y
+# CONFIG_USB is not set
+
+#
+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+#
+
+#
+# USB Gadget Support
+#
+# CONFIG_USB_GADGET is not set
+
+#
+# MMC/SD Card support
+#
+# CONFIG_MMC is not set
+
+#
+# LED devices
+#
+# CONFIG_NEW_LEDS is not set
+
+#
+# LED drivers
+#
+
+#
+# LED Triggers
+#
+
+#
+# InfiniBand support
+#
+# CONFIG_INFINIBAND is not set
+
+#
+# EDAC - error detection and reporting (RAS) (EXPERIMENTAL)
+#
+
+#
+# Real Time Clock
+#
+# CONFIG_RTC_CLASS is not set
+
+#
+# DMA Engine support
+#
+# CONFIG_DMA_ENGINE is not set
+
+#
+# DMA Clients
+#
+
+#
+# DMA Devices
+#
+
+#
+# Auxiliary Display support
+#
+
+#
+# Virtualization
+#
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+# CONFIG_EXT2_FS_XATTR is not set
+# CONFIG_EXT2_FS_XIP is not set
+# CONFIG_EXT3_FS is not set
+# CONFIG_EXT4DEV_FS is not set
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
+# CONFIG_QUOTA is not set
+CONFIG_DNOTIFY=y
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+CONFIG_RAMFS=y
+# CONFIG_CONFIGFS_FS is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+CONFIG_CRAMFS=y
+# CONFIG_VXFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+
+#
+# Network File Systems
+#
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+# CONFIG_NFS_V4 is not set
+# CONFIG_NFS_DIRECTIO is not set
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+# CONFIG_9P_FS is not set
+
+#
+# Partition Types
+#
+# CONFIG_PARTITION_ADVANCED is not set
+CONFIG_MSDOS_PARTITION=y
+
+#
+# Native Language Support
+#
+# CONFIG_NLS is not set
+
+#
+# Distributed Lock Manager
+#
+# CONFIG_DLM is not set
+# CONFIG_UCC_SLOW is not set
+# CONFIG_UCC_FAST is not set
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+CONFIG_CRC32=y
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_PLIST=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+
+#
+# Instrumentation Support
+#
+# CONFIG_PROFILING is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_DETECT_SOFTLOCKUP=y
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_DEBUG_SLAB is not set
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+# CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+CONFIG_DEBUG_BUGVERBOSE=y
+# CONFIG_DEBUG_INFO is not set
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_LIST is not set
+CONFIG_FORCED_INLINING=y
+# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_DEBUG_STACKOVERFLOW is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_PAGEALLOC is not set
+# CONFIG_DEBUGGER is not set
+# CONFIG_BDI_SWITCH is not set
+# CONFIG_BOOTX_TEXT is not set
+# CONFIG_SERIAL_TEXT_DEBUG is not set
+# CONFIG_PPC_EARLY_DEBUG is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+
+#
+# Cryptographic options
+#
+CONFIG_CRYPTO=y
+CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_BLKCIPHER=y
+CONFIG_CRYPTO_MANAGER=y
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_MD4 is not set
+CONFIG_CRYPTO_MD5=y
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_WP512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+# CONFIG_CRYPTO_GF128MUL is not set
+CONFIG_CRYPTO_ECB=y
+CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_PCBC=y
+# CONFIG_CRYPTO_LRW is not set
+CONFIG_CRYPTO_DES=y
+# CONFIG_CRYPTO_FCRYPT is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_TEST is not set
+
+#
+# Hardware crypto devices
+#

arch/powerpc/platforms/44x/Makefile +1 -0

Index: working-2.6/arch/powerpc/platforms/44x/Makefile
===================================================================
@@ -1 +1,2 @@
 obj-$(CONFIG_44x)	:= misc_44x.o
+obj-$(CONFIG_EBONY)	+= ebony.o

arch/powerpc/platforms/44x/ebony.c new file +73 -0

73 lines not on this page · raw message

arch/powerpc/platforms/44x/Kconfig new file +56 -0

56 lines not on this page · raw message

arch/powerpc/platforms/Kconfig +1 -0

Index: working-2.6/arch/powerpc/platforms/Kconfig
===================================================================
@@ -42,6 +42,7 @@ source "arch/powerpc/platforms/83xx/Kcon
 source "arch/powerpc/platforms/85xx/Kconfig"
 source "arch/powerpc/platforms/86xx/Kconfig"
 source "arch/powerpc/platforms/embedded6xx/Kconfig"
+source "arch/powerpc/platforms/44x/Kconfig"
 #source "arch/powerpc/platforms/4xx/Kconfig
 
 config PPC_NATIVE

arch/powerpc/Kconfig +7 -1

Index: working-2.6/arch/powerpc/Kconfig
===================================================================
@@ -201,6 +201,7 @@ config 40x
 config 44x
 	bool "AMCC 44x"
 	select PPC_DCR_NATIVE
+	select WANT_DEVICE_TREE
 
 config E200
 	bool "Freescale e200"

@@ -265,9 +266,14 @@ config PPC_OF_PLATFORM_PCI
 	depends on PPC64 # not supported on 32 bits yet
 	default n
 
+config 4xx
+	bool
+	depends on 40x || 44x
+	default y
+
 config BOOKE
 	bool
-	depends on E200 || E500
+	depends on E200 || E500 || 44x
 	default y
 
 config FSL_BOOKE

arch/powerpc/boot/44x.c new file +40 -0

Index: working-2.6/arch/powerpc/boot/44x.c
===================================================================
@@ -0,0 +1,40 @@
+/*
+ * Copyright 2007 David Gibson, IBM Corporation.
+ *
+ * Based on earlier code:
+ *   Matt Porter <[email protected]>
+ *   Copyright 2002-2005 MontaVista Software Inc.
+ *
+ *   Eugene Surovegin <[email protected]> or <[email protected]>
+ *   Copyright (c) 2003, 2004 Zultys Technologies
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+#include <stddef.h>
+#include "types.h"
+#include "string.h"
+#include "stdio.h"
+#include "ops.h"
+#include "reg.h"
+#include "dcr.h"
+
+/* Read the 44x memory controller to get size of system memory. */
+void ibm44x_fixup_memsize(void)
+{
+	int i;
+	unsigned long memsize, bank_config;
+
+	memsize = 0;
+	for (i = 0; i < ARRAY_SIZE(sdram_bxcr); i++) {
+		mtdcr(DCRN_SDRAM0_CFGADDR, sdram_bxcr[i]);
+		bank_config = mfdcr(DCRN_SDRAM0_CFGDATA);
+
+		if (bank_config & SDRAM_CONFIG_BANK_ENABLE)
+			memsize += SDRAM_CONFIG_BANK_SIZE(bank_config);
+	}
+
+	dt_fixup_memory(0, memsize);
+}

arch/powerpc/boot/44x.h new file +16 -0

Index: working-2.6/arch/powerpc/boot/44x.h
===================================================================
@@ -0,0 +1,16 @@
+/*
+ * PowerPC 44x related functions
+ *
+ * Copyright 2007 David Gibson, IBM Corporation.
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+#ifndef _PPC_BOOT_44X_H_
+#define _PPC_BOOT_44X_H_
+
+void ibm44x_fixup_memsize(void);
+void ebony_init(void *mac0, void *mac1);
+
+#endif /* _PPC_BOOT_44X_H_ */

arch/powerpc/boot/Makefile +14 -4

Index: working-2.6/arch/powerpc/boot/Makefile
===================================================================
@@ -42,8 +42,9 @@ $(addprefix $(obj)/,$(zlib) gunzip_util.
 
 src-wlib := string.S crt0.S stdio.c main.c flatdevtree.c flatdevtree_misc.c \
 		ns16550.c serial.c simple_alloc.c div64.S util.S \
-		gunzip_util.c elf_util.c $(zlib) devtree.c
-src-plat := of.c cuboot-83xx.c cuboot-85xx.c
+		gunzip_util.c elf_util.c $(zlib) devtree.c \
+		44x.c ebony.c
+src-plat := of.c cuboot-83xx.c cuboot-85xx.c cuboot-ebony.c treeboot-ebony.c
 src-boot := $(src-wlib) $(src-plat) empty.c
 
 src-boot := $(addprefix $(obj)/, $(src-boot))

@@ -134,6 +135,7 @@ image-$(CONFIG_DEFAULT_UIMAGE)		+= uImag
 ifneq ($(CONFIG_DEVICE_TREE),"")
 image-$(CONFIG_PPC_83xx)		+= cuImage.83xx
 image-$(CONFIG_PPC_85xx)		+= cuImage.85xx
+image-$(CONFIG_EBONY)			+= treeImage.ebony cuImage.ebony
 endif
 
 # For 32-bit powermacs, build the COFF and miboot images

@@ -143,7 +145,8 @@ image-$(CONFIG_PPC_PMAC)	+= zImage.coff 
 endif
 
 initrd-  := $(patsubst zImage%, zImage.initrd%, $(image-n) $(image-))
-initrd-y := $(patsubst zImage%, zImage.initrd%, $(image-y))
+initrd-y := $(patsubst zImage%, zImage.initrd%, \
+		$(patsubst treeImage%, treeImage.initrd%, $(image-y)))
 initrd-y := $(filter-out $(image-y), $(initrd-y))
 targets	+= $(image-y) $(initrd-y)

@@ -174,6 +177,12 @@ dts = $(if $(shell echo $(CONFIG_DEVICE_
 $(obj)/cuImage.%: vmlinux $(dts) $(wrapperbits)
 	$(call if_changed,wrap,cuboot-$*,$(dts))
 
+$(obj)/treeImage.%: vmlinux $(dts) $(wrapperbits)
+	$(call if_changed,wrap,treeboot-$*,$(dts))
+
+$(obj)/treeImage.initrd.%: vmlinux $(dts) $(wrapperbits)
+	$(call if_changed,wrap,treeboot-$*,$(dts),,$(obj)/ramdisk.image.gz)
+
 $(obj)/zImage:		$(addprefix $(obj)/, $(image-y))
 	@rm -f $@; ln $< $@
 $(obj)/zImage.initrd:	$(addprefix $(obj)/, $(initrd-y))

@@ -183,7 +192,8 @@ install: $(CONFIGURE) $(addprefix $(obj)
 	sh -x $(srctree)/$(src)/install.sh "$(KERNELRELEASE)" vmlinux System.map "$(INSTALL_PATH)" $<
 
 # anything not in $(targets)
-clean-files += $(image-) $(initrd-) zImage zImage.initrd cuImage.*
+clean-files += $(image-) $(initrd-) zImage zImage.initrd cuImage.* \
+	treeImage.*
 
 # clean up files cached by wrapper
 clean-kernel := vmlinux.strip vmlinux.bin

arch/powerpc/boot/cuboot-ebony.c new file +42 -0

42 lines not on this page · raw message

arch/powerpc/boot/dcr.h new file +87 -0

87 lines not on this page · raw message

arch/powerpc/boot/ebony.c new file +129 -0

129 lines not on this page · raw message

arch/powerpc/boot/mktree.c +4 -6

Index: working-2.6/arch/powerpc/boot/mktree.c
===================================================================
@@ -46,8 +46,8 @@ int main(int argc, char *argv[])
 	struct	stat	st;
 	boot_block_t	bt;
 
-	if (argc < 3) {
-		fprintf(stderr, "usage: %s <zImage-file> <boot-image> [entry-point]\n",argv[0]);
+	if (argc < 5) {
+		fprintf(stderr, "usage: %s <zImage-file> <boot-image> <load address> <entry point>\n",argv[0]);
 		exit(1);
 	}

@@ -61,10 +61,8 @@ int main(int argc, char *argv[])
 	bt.bb_magic = htonl(0x0052504F);
 
 	/* If we have the optional entry point parameter, use it */
-	if (argc == 4)
-		bt.bb_dest = bt.bb_entry_point = htonl(strtoul(argv[3], NULL, 0));
-	else
-		bt.bb_dest = bt.bb_entry_point = htonl(0x500000);
+	bt.bb_dest = htonl(strtoul(argv[3], NULL, 0));
+	bt.bb_entry_point = htonl(strtoul(argv[4], NULL, 0));
 
 	/* We know these from the linker command.
 	 * ...and then move it up into memory a little more so the

arch/powerpc/boot/treeboot-ebony.c new file +34 -0

Index: working-2.6/arch/powerpc/boot/treeboot-ebony.c
===================================================================
@@ -0,0 +1,34 @@
+/*
+ * Old U-boot compatibility for Ebony
+ *
+ * Author: David Gibson <[email protected]>
+ *
+ * Copyright 2007 David Gibson, IBM Corporatio.
+ *   Based on cuboot-83xx.c, which is:
+ * Copyright (c) 2007 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include "ops.h"
+#include "stdio.h"
+#include "44x.h"
+
+extern char _end[];
+
+BSS_STACK(4096);
+
+#define OPENBIOS_MAC_BASE	0xfffffe0c
+#define OPENBIOS_MAC_OFFSET	0xc
+
+void platform_init(void)
+{
+	unsigned long end_of_ram = 0x8000000;
+	unsigned long avail_ram = end_of_ram - (unsigned long)_end;
+
+	simple_alloc_init(_end, avail_ram, 32, 64);
+	ebony_init((u8 *)OPENBIOS_MAC_BASE,
+		   (u8 *)(OPENBIOS_MAC_BASE + OPENBIOS_MAC_OFFSET));
+}

arch/powerpc/boot/wrapper +8 -0

Index: working-2.6/arch/powerpc/boot/wrapper
===================================================================
@@ -231,4 +231,12 @@ cuboot*)
     mkimage -A ppc -O linux -T kernel -C gzip -a "$base" -e "$entry" \
             $uboot_version -d "$ofile".bin.gz "$ofile"
     ;;
+treeboot*)
+    mv "$ofile" "$ofile.elf"
+    $object/mktree "$ofile.elf" "$ofile" "$base" "$entry"
+    if [ -z "$cacheit" ]; then
+	rm -f "$ofile.elf"
+    fi
+    exit 0
+    ;;
 esac

David Gibson

author

2007-05-08 04:10 UTC #8 lore raw

Re: [PATCH 5/7] Support for the Ebony 440GP reference board in arch/powerpc

Support for the Ebony 440GP reference board in arch/powerpc

Signed-off-by David Gibson <[email protected]>

---
Revised for change from "Ebony" to "ibm,ebony" in the device tree root compatible property.

arch/powerpc/configs/ebony_defconfig new file +905 -0

Index: working-2.6/arch/powerpc/configs/ebony_defconfig
===================================================================
@@ -0,0 +1,905 @@
+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.21
+# Fri May  4 13:47:08 2007
+#
+# CONFIG_PPC64 is not set
+CONFIG_PPC32=y
+CONFIG_PPC_MERGE=y
+CONFIG_MMU=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_IRQ_PER_CPU=y
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_ARCH_HAS_ILOG2_U32=y
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+CONFIG_PPC=y
+CONFIG_EARLY_PRINTK=y
+CONFIG_GENERIC_NVRAM=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+CONFIG_PPC_OF=y
+# CONFIG_PPC_UDBG_16550 is not set
+# CONFIG_GENERIC_TBSYNC is not set
+CONFIG_AUDIT_ARCH=y
+CONFIG_GENERIC_BUG=y
+# CONFIG_DEFAULT_UIMAGE is not set
+
+#
+# Processor support
+#
+# CONFIG_CLASSIC32 is not set
+# CONFIG_PPC_82xx is not set
+# CONFIG_PPC_83xx is not set
+# CONFIG_PPC_85xx is not set
+# CONFIG_PPC_86xx is not set
+# CONFIG_PPC_8xx is not set
+# CONFIG_40x is not set
+CONFIG_44x=y
+# CONFIG_E200 is not set
+CONFIG_PPC_DCR_NATIVE=y
+# CONFIG_PPC_DCR_MMIO is not set
+CONFIG_PPC_DCR=y
+CONFIG_4xx=y
+CONFIG_BOOKE=y
+CONFIG_PTE_64BIT=y
+CONFIG_PHYS_64BIT=y
+CONFIG_NOT_COHERENT_CACHE=y
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+
+#
+# Code maturity level options
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+
+#
+# General setup
+#
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+# CONFIG_IPC_NS is not set
+CONFIG_SYSVIPC_SYSCTL=y
+CONFIG_POSIX_MQUEUE=y
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_UTS_NS is not set
+# CONFIG_AUDIT is not set
+# CONFIG_IKCONFIG is not set
+CONFIG_SYSFS_DEPRECATED=y
+# CONFIG_RELAY is not set
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_INITRAMFS_SOURCE=""
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SYSCTL=y
+CONFIG_EMBEDDED=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS=y
+CONFIG_KALLSYMS_ALL=y
+CONFIG_KALLSYMS_EXTRA_PASS=y
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_EPOLL=y
+CONFIG_SHMEM=y
+CONFIG_SLAB=y
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_RT_MUTEXES=y
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=0
+# CONFIG_SLOB is not set
+
+#
+# Loadable module support
+#
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_MODULE_FORCE_UNLOAD is not set
+# CONFIG_MODVERSIONS is not set
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+CONFIG_KMOD=y
+
+#
+# Block layer
+#
+CONFIG_BLOCK=y
+CONFIG_LBD=y
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+CONFIG_DEFAULT_AS=y
+# CONFIG_DEFAULT_DEADLINE is not set
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="anticipatory"
+
+#
+# Platform support
+#
+# CONFIG_PPC_MPC52xx is not set
+# CONFIG_PPC_MPC5200 is not set
+# CONFIG_PPC_CELL is not set
+# CONFIG_PPC_CELL_NATIVE is not set
+# CONFIG_PQ2ADS is not set
+CONFIG_EBONY=y
+CONFIG_440GP=y
+# CONFIG_MPIC is not set
+# CONFIG_MPIC_WEIRD is not set
+# CONFIG_PPC_I8259 is not set
+# CONFIG_PPC_RTAS is not set
+# CONFIG_MMIO_NVRAM is not set
+# CONFIG_PPC_MPC106 is not set
+# CONFIG_PPC_970_NAP is not set
+# CONFIG_PPC_INDIRECT_IO is not set
+# CONFIG_GENERIC_IOMAP is not set
+# CONFIG_CPU_FREQ is not set
+# CONFIG_CPM2 is not set
+
+#
+# Kernel options
+#
+# CONFIG_HIGHMEM is not set
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_250=y
+# CONFIG_HZ_300 is not set
+# CONFIG_HZ_1000 is not set
+CONFIG_HZ=250
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_BINFMT_ELF=y
+# CONFIG_BINFMT_MISC is not set
+CONFIG_MATH_EMULATION=y
+CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
+CONFIG_ARCH_FLATMEM_ENABLE=y
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4
+CONFIG_RESOURCES_64BIT=y
+CONFIG_ZONE_DMA_FLAG=1
+CONFIG_PROC_DEVICETREE=y
+# CONFIG_CMDLINE_BOOL is not set
+CONFIG_SECCOMP=y
+CONFIG_WANT_DEVICE_TREE=y
+CONFIG_DEVICE_TREE="ebony.dts"
+CONFIG_ISA_DMA_API=y
+
+#
+# Bus options
+#
+CONFIG_ZONE_DMA=y
+CONFIG_PPC_INDIRECT_PCI=y
+# CONFIG_PPC_INDIRECT_PCI_BE is not set
+CONFIG_PCI=y
+CONFIG_PCI_DOMAINS=y
+# CONFIG_PCIEPORTBUS is not set
+# CONFIG_PCI_DEBUG is not set
+
+#
+# PCCARD (PCMCIA/CardBus) support
+#
+# CONFIG_PCCARD is not set
+
+#
+# PCI Hotplug Support
+#
+# CONFIG_HOTPLUG_PCI is not set
+
+#
+# Advanced setup
+#
+# CONFIG_ADVANCED_OPTIONS is not set
+
+#
+# Default settings for advanced configuration options are used
+#
+CONFIG_HIGHMEM_START=0xfe000000
+CONFIG_LOWMEM_SIZE=0x30000000
+CONFIG_KERNEL_START=0xc0000000
+CONFIG_TASK_SIZE=0x80000000
+CONFIG_CONSISTENT_START=0xff100000
+CONFIG_CONSISTENT_SIZE=0x00200000
+CONFIG_BOOT_LOAD=0x01000000
+
+#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+# CONFIG_IP_MULTICAST is not set
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_ARPD is not set
+# CONFIG_SYN_COOKIES is not set
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_INET6_XFRM_TUNNEL is not set
+# CONFIG_INET6_TUNNEL is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+
+#
+# DCCP Configuration (EXPERIMENTAL)
+#
+# CONFIG_IP_DCCP is not set
+
+#
+# SCTP Configuration (EXPERIMENTAL)
+#
+# CONFIG_IP_SCTP is not set
+
+#
+# TIPC Configuration (EXPERIMENTAL)
+#
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+
+#
+# QoS and/or fair queueing
+#
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_AF_RXRPC is not set
+
+#
+# Wireless
+#
+# CONFIG_CFG80211 is not set
+# CONFIG_WIRELESS_EXT is not set
+# CONFIG_IEEE80211 is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+CONFIG_FW_LOADER=y
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+
+#
+# Connector - unified userspace <-> kernelspace linker
+#
+CONFIG_CONNECTOR=y
+CONFIG_PROC_EVENTS=y
+# CONFIG_MTD is not set
+
+#
+# Parallel port support
+#
+# CONFIG_PARPORT is not set
+
+#
+# Plug and Play support
+#
+# CONFIG_PNPACPI is not set
+
+#
+# Block devices
+#
+# CONFIG_BLK_DEV_FD is not set
+# CONFIG_BLK_CPQ_DA is not set
+# CONFIG_BLK_CPQ_CISS_DA is not set
+# CONFIG_BLK_DEV_DAC960 is not set
+# CONFIG_BLK_DEV_UMEM is not set
+# CONFIG_BLK_DEV_COW_COMMON is not set
+# CONFIG_BLK_DEV_LOOP is not set
+# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_SX8 is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=35000
+CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+
+#
+# Misc devices
+#
+# CONFIG_SGI_IOC4 is not set
+# CONFIG_TIFM_CORE is not set
+
+#
+# ATA/ATAPI/MFM/RLL support
+#
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+# CONFIG_SCSI is not set
+# CONFIG_SCSI_NETLINK is not set
+
+#
+# Serial ATA (prod) and Parallel ATA (experimental) drivers
+#
+# CONFIG_ATA is not set
+
+#
+# Multi-device support (RAID and LVM)
+#
+# CONFIG_MD is not set
+
+#
+# Fusion MPT device support
+#
+# CONFIG_FUSION is not set
+
+#
+# IEEE 1394 (FireWire) support
+#
+# CONFIG_IEEE1394 is not set
+
+#
+# I2O device support
+#
+# CONFIG_I2O is not set
+# CONFIG_MACINTOSH_DRIVERS is not set
+
+#
+# Network device support
+#
+CONFIG_NETDEVICES=y
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_EQUALIZER is not set
+# CONFIG_TUN is not set
+
+#
+# ARCnet devices
+#
+# CONFIG_ARCNET is not set
+
+#
+# PHY device support
+#
+
+#
+# Ethernet (10 or 100Mbit)
+#
+# CONFIG_NET_ETHERNET is not set
+CONFIG_IBM_NEW_EMAC=y
+CONFIG_IBM_NEW_EMAC_RXB=128
+CONFIG_IBM_NEW_EMAC_TXB=64
+CONFIG_IBM_NEW_EMAC_POLL_WEIGHT=32
+CONFIG_IBM_NEW_EMAC_RX_COPY_THRESHOLD=256
+CONFIG_IBM_NEW_EMAC_RX_SKB_HEADROOM=0
+# CONFIG_IBM_NEW_EMAC_DEBUG is not set
+CONFIG_IBM_NEW_EMAC_ZMII=y
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+
+#
+# Ethernet (1000 Mbit)
+#
+# CONFIG_ACENIC is not set
+# CONFIG_DL2K is not set
+# CONFIG_E1000 is not set
+# CONFIG_NS83820 is not set
+# CONFIG_HAMACHI is not set
+# CONFIG_YELLOWFIN is not set
+# CONFIG_R8169 is not set
+# CONFIG_SIS190 is not set
+# CONFIG_SKGE is not set
+# CONFIG_SKY2 is not set
+# CONFIG_SK98LIN is not set
+# CONFIG_TIGON3 is not set
+# CONFIG_BNX2 is not set
+# CONFIG_QLA3XXX is not set
+# CONFIG_ATL1 is not set
+
+#
+# Ethernet (10000 Mbit)
+#
+# CONFIG_CHELSIO_T1 is not set
+# CONFIG_CHELSIO_T3 is not set
+# CONFIG_IXGB is not set
+# CONFIG_S2IO is not set
+# CONFIG_MYRI10GE is not set
+# CONFIG_NETXEN_NIC is not set
+
+#
+# Token Ring devices
+#
+# CONFIG_TR is not set
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+# CONFIG_WLAN_80211 is not set
+
+#
+# Wan interfaces
+#
+# CONFIG_WAN is not set
+# CONFIG_FDDI is not set
+# CONFIG_HIPPI is not set
+# CONFIG_PPP is not set
+# CONFIG_SLIP is not set
+# CONFIG_SHAPER is not set
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+
+#
+# ISDN subsystem
+#
+# CONFIG_ISDN is not set
+
+#
+# Telephony Support
+#
+# CONFIG_PHONE is not set
+
+#
+# Input device support
+#
+# CONFIG_INPUT is not set
+
+#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+# CONFIG_VT is not set
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+# CONFIG_SERIAL_8250_PCI is not set
+CONFIG_SERIAL_8250_NR_UARTS=4
+CONFIG_SERIAL_8250_RUNTIME_UARTS=4
+CONFIG_SERIAL_8250_EXTENDED=y
+# CONFIG_SERIAL_8250_MANY_PORTS is not set
+CONFIG_SERIAL_8250_SHARE_IRQ=y
+# CONFIG_SERIAL_8250_DETECT_IRQ is not set
+# CONFIG_SERIAL_8250_RSA is not set
+
+#
+# Non-8250 serial port support
+#
+# CONFIG_SERIAL_UARTLITE is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+# CONFIG_SERIAL_JSM is not set
+CONFIG_SERIAL_OF_PLATFORM=y
+CONFIG_UNIX98_PTYS=y
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+
+#
+# IPMI
+#
+# CONFIG_IPMI_HANDLER is not set
+
+#
+# Watchdog Cards
+#
+# CONFIG_WATCHDOG is not set
+# CONFIG_HW_RANDOM is not set
+# CONFIG_NVRAM is not set
+# CONFIG_GEN_RTC is not set
+# CONFIG_DTLK is not set
+# CONFIG_R3964 is not set
+# CONFIG_APPLICOM is not set
+# CONFIG_AGP is not set
+# CONFIG_DRM is not set
+# CONFIG_RAW_DRIVER is not set
+
+#
+# TPM devices
+#
+# CONFIG_TCG_TPM is not set
+
+#
+# I2C support
+#
+# CONFIG_I2C is not set
+
+#
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+
+#
+# Dallas's 1-wire bus
+#
+# CONFIG_W1 is not set
+
+#
+# Hardware Monitoring support
+#
+# CONFIG_HWMON is not set
+# CONFIG_HWMON_VID is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_SM501 is not set
+
+#
+# Multimedia devices
+#
+# CONFIG_VIDEO_DEV is not set
+
+#
+# Digital Video Broadcasting Devices
+#
+# CONFIG_DVB is not set
+
+#
+# Graphics support
+#
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+# CONFIG_FB is not set
+# CONFIG_FB_IBM_GXT4500 is not set
+
+#
+# Sound
+#
+# CONFIG_SOUND is not set
+
+#
+# USB support
+#
+CONFIG_USB_ARCH_HAS_HCD=y
+CONFIG_USB_ARCH_HAS_OHCI=y
+CONFIG_USB_ARCH_HAS_EHCI=y
+# CONFIG_USB is not set
+
+#
+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+#
+
+#
+# USB Gadget Support
+#
+# CONFIG_USB_GADGET is not set
+
+#
+# MMC/SD Card support
+#
+# CONFIG_MMC is not set
+
+#
+# LED devices
+#
+# CONFIG_NEW_LEDS is not set
+
+#
+# LED drivers
+#
+
+#
+# LED Triggers
+#
+
+#
+# InfiniBand support
+#
+# CONFIG_INFINIBAND is not set
+
+#
+# EDAC - error detection and reporting (RAS) (EXPERIMENTAL)
+#
+
+#
+# Real Time Clock
+#
+# CONFIG_RTC_CLASS is not set
+
+#
+# DMA Engine support
+#
+# CONFIG_DMA_ENGINE is not set
+
+#
+# DMA Clients
+#
+
+#
+# DMA Devices
+#
+
+#
+# Auxiliary Display support
+#
+
+#
+# Virtualization
+#
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=y
+# CONFIG_EXT2_FS_XATTR is not set
+# CONFIG_EXT2_FS_XIP is not set
+# CONFIG_EXT3_FS is not set
+# CONFIG_EXT4DEV_FS is not set
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+# CONFIG_FS_POSIX_ACL is not set
+# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_ROMFS_FS is not set
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
+# CONFIG_QUOTA is not set
+CONFIG_DNOTIFY=y
+# CONFIG_AUTOFS_FS is not set
+# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
+# CONFIG_HUGETLB_PAGE is not set
+CONFIG_RAMFS=y
+# CONFIG_CONFIGFS_FS is not set
+
+#
+# Miscellaneous filesystems
+#
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+CONFIG_CRAMFS=y
+# CONFIG_VXFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+
+#
+# Network File Systems
+#
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
+# CONFIG_NFS_V4 is not set
+# CONFIG_NFS_DIRECTIO is not set
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+# CONFIG_9P_FS is not set
+
+#
+# Partition Types
+#
+# CONFIG_PARTITION_ADVANCED is not set
+CONFIG_MSDOS_PARTITION=y
+
+#
+# Native Language Support
+#
+# CONFIG_NLS is not set
+
+#
+# Distributed Lock Manager
+#
+# CONFIG_DLM is not set
+# CONFIG_UCC_SLOW is not set
+# CONFIG_UCC_FAST is not set
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
+CONFIG_CRC32=y
+# CONFIG_LIBCRC32C is not set
+CONFIG_ZLIB_INFLATE=y
+CONFIG_PLIST=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+
+#
+# Instrumentation Support
+#
+# CONFIG_PROFILING is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_MUST_CHECK=y
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_DETECT_SOFTLOCKUP=y
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_DEBUG_SLAB is not set
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+# CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+CONFIG_DEBUG_BUGVERBOSE=y
+# CONFIG_DEBUG_INFO is not set
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_LIST is not set
+CONFIG_FORCED_INLINING=y
+# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_DEBUG_STACKOVERFLOW is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_PAGEALLOC is not set
+# CONFIG_DEBUGGER is not set
+# CONFIG_BDI_SWITCH is not set
+# CONFIG_BOOTX_TEXT is not set
+# CONFIG_SERIAL_TEXT_DEBUG is not set
+# CONFIG_PPC_EARLY_DEBUG is not set
+
+#
+# Security options
+#
+# CONFIG_KEYS is not set
+# CONFIG_SECURITY is not set
+
+#
+# Cryptographic options
+#
+CONFIG_CRYPTO=y
+CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_BLKCIPHER=y
+CONFIG_CRYPTO_MANAGER=y
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_MD4 is not set
+CONFIG_CRYPTO_MD5=y
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_WP512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+# CONFIG_CRYPTO_GF128MUL is not set
+CONFIG_CRYPTO_ECB=y
+CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_PCBC=y
+# CONFIG_CRYPTO_LRW is not set
+CONFIG_CRYPTO_DES=y
+# CONFIG_CRYPTO_FCRYPT is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
+# CONFIG_CRYPTO_TEST is not set
+
+#
+# Hardware crypto devices
+#

arch/powerpc/platforms/44x/Makefile +1 -0

Index: working-2.6/arch/powerpc/platforms/44x/Makefile
===================================================================
@@ -1 +1,2 @@
 obj-$(CONFIG_44x)	:= misc_44x.o
+obj-$(CONFIG_EBONY)	+= ebony.o

arch/powerpc/platforms/44x/ebony.c new file +73 -0

73 lines not on this page · raw message

arch/powerpc/platforms/44x/Kconfig new file +56 -0

56 lines not on this page · raw message

arch/powerpc/platforms/Kconfig +1 -0

Index: working-2.6/arch/powerpc/platforms/Kconfig
===================================================================
@@ -42,6 +42,7 @@ source "arch/powerpc/platforms/83xx/Kcon
 source "arch/powerpc/platforms/85xx/Kconfig"
 source "arch/powerpc/platforms/86xx/Kconfig"
 source "arch/powerpc/platforms/embedded6xx/Kconfig"
+source "arch/powerpc/platforms/44x/Kconfig"
 #source "arch/powerpc/platforms/4xx/Kconfig
 
 config PPC_NATIVE

arch/powerpc/Kconfig +7 -1

Index: working-2.6/arch/powerpc/Kconfig
===================================================================
@@ -201,6 +201,7 @@ config 40x
 config 44x
 	bool "AMCC 44x"
 	select PPC_DCR_NATIVE
+	select WANT_DEVICE_TREE
 
 config E200
 	bool "Freescale e200"

@@ -265,9 +266,14 @@ config PPC_OF_PLATFORM_PCI
 	depends on PPC64 # not supported on 32 bits yet
 	default n
 
+config 4xx
+	bool
+	depends on 40x || 44x
+	default y
+
 config BOOKE
 	bool
-	depends on E200 || E500
+	depends on E200 || E500 || 44x
 	default y
 
 config FSL_BOOKE

arch/powerpc/boot/44x.c new file +40 -0

Index: working-2.6/arch/powerpc/boot/44x.c
===================================================================
@@ -0,0 +1,40 @@
+/*
+ * Copyright 2007 David Gibson, IBM Corporation.
+ *
+ * Based on earlier code:
+ *   Matt Porter <[email protected]>
+ *   Copyright 2002-2005 MontaVista Software Inc.
+ *
+ *   Eugene Surovegin <[email protected]> or <[email protected]>
+ *   Copyright (c) 2003, 2004 Zultys Technologies
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+#include <stddef.h>
+#include "types.h"
+#include "string.h"
+#include "stdio.h"
+#include "ops.h"
+#include "reg.h"
+#include "dcr.h"
+
+/* Read the 44x memory controller to get size of system memory. */
+void ibm44x_fixup_memsize(void)
+{
+	int i;
+	unsigned long memsize, bank_config;
+
+	memsize = 0;
+	for (i = 0; i < ARRAY_SIZE(sdram_bxcr); i++) {
+		mtdcr(DCRN_SDRAM0_CFGADDR, sdram_bxcr[i]);
+		bank_config = mfdcr(DCRN_SDRAM0_CFGDATA);
+
+		if (bank_config & SDRAM_CONFIG_BANK_ENABLE)
+			memsize += SDRAM_CONFIG_BANK_SIZE(bank_config);
+	}
+
+	dt_fixup_memory(0, memsize);
+}

arch/powerpc/boot/44x.h new file +16 -0

Index: working-2.6/arch/powerpc/boot/44x.h
===================================================================
@@ -0,0 +1,16 @@
+/*
+ * PowerPC 44x related functions
+ *
+ * Copyright 2007 David Gibson, IBM Corporation.
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+#ifndef _PPC_BOOT_44X_H_
+#define _PPC_BOOT_44X_H_
+
+void ibm44x_fixup_memsize(void);
+void ebony_init(void *mac0, void *mac1);
+
+#endif /* _PPC_BOOT_44X_H_ */

arch/powerpc/boot/Makefile +14 -4

Index: working-2.6/arch/powerpc/boot/Makefile
===================================================================
@@ -42,8 +42,9 @@ $(addprefix $(obj)/,$(zlib) gunzip_util.
 
 src-wlib := string.S crt0.S stdio.c main.c flatdevtree.c flatdevtree_misc.c \
 		ns16550.c serial.c simple_alloc.c div64.S util.S \
-		gunzip_util.c elf_util.c $(zlib) devtree.c
-src-plat := of.c cuboot-83xx.c cuboot-85xx.c
+		gunzip_util.c elf_util.c $(zlib) devtree.c \
+		44x.c ebony.c
+src-plat := of.c cuboot-83xx.c cuboot-85xx.c cuboot-ebony.c treeboot-ebony.c
 src-boot := $(src-wlib) $(src-plat) empty.c
 
 src-boot := $(addprefix $(obj)/, $(src-boot))

@@ -134,6 +135,7 @@ image-$(CONFIG_DEFAULT_UIMAGE)		+= uImag
 ifneq ($(CONFIG_DEVICE_TREE),"")
 image-$(CONFIG_PPC_83xx)		+= cuImage.83xx
 image-$(CONFIG_PPC_85xx)		+= cuImage.85xx
+image-$(CONFIG_EBONY)			+= treeImage.ebony cuImage.ebony
 endif
 
 # For 32-bit powermacs, build the COFF and miboot images

@@ -143,7 +145,8 @@ image-$(CONFIG_PPC_PMAC)	+= zImage.coff 
 endif
 
 initrd-  := $(patsubst zImage%, zImage.initrd%, $(image-n) $(image-))
-initrd-y := $(patsubst zImage%, zImage.initrd%, $(image-y))
+initrd-y := $(patsubst zImage%, zImage.initrd%, \
+		$(patsubst treeImage%, treeImage.initrd%, $(image-y)))
 initrd-y := $(filter-out $(image-y), $(initrd-y))
 targets	+= $(image-y) $(initrd-y)

@@ -174,6 +177,12 @@ dts = $(if $(shell echo $(CONFIG_DEVICE_
 $(obj)/cuImage.%: vmlinux $(dts) $(wrapperbits)
 	$(call if_changed,wrap,cuboot-$*,$(dts))
 
+$(obj)/treeImage.%: vmlinux $(dts) $(wrapperbits)
+	$(call if_changed,wrap,treeboot-$*,$(dts))
+
+$(obj)/treeImage.initrd.%: vmlinux $(dts) $(wrapperbits)
+	$(call if_changed,wrap,treeboot-$*,$(dts),,$(obj)/ramdisk.image.gz)
+
 $(obj)/zImage:		$(addprefix $(obj)/, $(image-y))
 	@rm -f $@; ln $< $@
 $(obj)/zImage.initrd:	$(addprefix $(obj)/, $(initrd-y))

@@ -183,7 +192,8 @@ install: $(CONFIGURE) $(addprefix $(obj)
 	sh -x $(srctree)/$(src)/install.sh "$(KERNELRELEASE)" vmlinux System.map "$(INSTALL_PATH)" $<
 
 # anything not in $(targets)
-clean-files += $(image-) $(initrd-) zImage zImage.initrd cuImage.*
+clean-files += $(image-) $(initrd-) zImage zImage.initrd cuImage.* \
+	treeImage.*
 
 # clean up files cached by wrapper
 clean-kernel := vmlinux.strip vmlinux.bin

arch/powerpc/boot/cuboot-ebony.c new file +42 -0

42 lines not on this page · raw message

arch/powerpc/boot/dcr.h new file +87 -0

87 lines not on this page · raw message

arch/powerpc/boot/ebony.c new file +129 -0

129 lines not on this page · raw message

arch/powerpc/boot/mktree.c +4 -6

Index: working-2.6/arch/powerpc/boot/mktree.c
===================================================================
@@ -46,8 +46,8 @@ int main(int argc, char *argv[])
 	struct	stat	st;
 	boot_block_t	bt;
 
-	if (argc < 3) {
-		fprintf(stderr, "usage: %s <zImage-file> <boot-image> [entry-point]\n",argv[0]);
+	if (argc < 5) {
+		fprintf(stderr, "usage: %s <zImage-file> <boot-image> <load address> <entry point>\n",argv[0]);
 		exit(1);
 	}

@@ -61,10 +61,8 @@ int main(int argc, char *argv[])
 	bt.bb_magic = htonl(0x0052504F);
 
 	/* If we have the optional entry point parameter, use it */
-	if (argc == 4)
-		bt.bb_dest = bt.bb_entry_point = htonl(strtoul(argv[3], NULL, 0));
-	else
-		bt.bb_dest = bt.bb_entry_point = htonl(0x500000);
+	bt.bb_dest = htonl(strtoul(argv[3], NULL, 0));
+	bt.bb_entry_point = htonl(strtoul(argv[4], NULL, 0));
 
 	/* We know these from the linker command.
 	 * ...and then move it up into memory a little more so the

arch/powerpc/boot/treeboot-ebony.c new file +34 -0

Index: working-2.6/arch/powerpc/boot/treeboot-ebony.c
===================================================================
@@ -0,0 +1,34 @@
+/*
+ * Old U-boot compatibility for Ebony
+ *
+ * Author: David Gibson <[email protected]>
+ *
+ * Copyright 2007 David Gibson, IBM Corporatio.
+ *   Based on cuboot-83xx.c, which is:
+ * Copyright (c) 2007 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include "ops.h"
+#include "stdio.h"
+#include "44x.h"
+
+extern char _end[];
+
+BSS_STACK(4096);
+
+#define OPENBIOS_MAC_BASE	0xfffffe0c
+#define OPENBIOS_MAC_OFFSET	0xc
+
+void platform_init(void)
+{
+	unsigned long end_of_ram = 0x8000000;
+	unsigned long avail_ram = end_of_ram - (unsigned long)_end;
+
+	simple_alloc_init(_end, avail_ram, 32, 64);
+	ebony_init((u8 *)OPENBIOS_MAC_BASE,
+		   (u8 *)(OPENBIOS_MAC_BASE + OPENBIOS_MAC_OFFSET));
+}

arch/powerpc/boot/wrapper +8 -0

Index: working-2.6/arch/powerpc/boot/wrapper
===================================================================
@@ -231,4 +231,12 @@ cuboot*)
     mkimage -A ppc -O linux -T kernel -C gzip -a "$base" -e "$entry" \
             $uboot_version -d "$ofile".bin.gz "$ofile"
     ;;
+treeboot*)
+    mv "$ofile" "$ofile.elf"
+    $object/mktree "$ofile.elf" "$ofile" "$base" "$entry"
+    if [ -z "$cacheit" ]; then
+	rm -f "$ofile.elf"
+    fi
+    exit 0
+    ;;
 esac

Signature · 4 lines

David Gibson			| I'll have my music baroque, and my code
david AT gibson.dropbear.id.au	| minimalist, thank you.  NOT _the_ _other_
				| _way_ _around_!
http://www.ozlabs.org/~dgibson

David Gibson

author

2007-05-08 02:59 UTC #9 lore raw

PATCH 6/7 Early serial debug support for PPC44x

In reply to David Gibson

This patch adds support for early serial debugging via the built in port on IBM/AMCC PowerPC 44x CPUs. It uses a bolted TLB entry in address space 1 for the UART's mapping, allowing robust debugging both before and after the initialization of the MMU.

Signed-off-by David Gibson <[email protected]>

---

 arch/powerpc/Kconfig.debug            |   22 ++++++++++++++++++----
 arch/powerpc/kernel/head_44x.S        |   34 +++++++++++++---------------------
 arch/powerpc/kernel/of_platform.c     |    1 -
 arch/powerpc/kernel/udbg.c            |    3 +++
 arch/powerpc/kernel/udbg_16550.c      |   23 +++++++++++++++++++++++
 arch/powerpc/platforms/44x/44x.h      |    2 ++
 arch/powerpc/platforms/44x/misc_44x.S |   31 +++++++++++++++++++++++++++++++
 include/asm-powerpc/mmu-44x.h         |    6 ++++++
 include/asm-powerpc/udbg.h            |    1 +
 9 files changed, 97 insertions(+), 26 deletions(-)

arch/powerpc/Kconfig.debug +18 -4

Index: working-2.6/arch/powerpc/Kconfig.debug
===================================================================
@@ -139,10 +139,6 @@ config BOOTX_TEXT
 	  Say Y here to see progress messages from the boot firmware in text
 	  mode. Requires either BootX or Open Firmware.
 
-config SERIAL_TEXT_DEBUG
-	bool "Support for early boot texts over serial port"
-	depends on 4xx
-
 config PPC_EARLY_DEBUG
 	bool "Early debugging (dangerous)"

@@ -207,6 +203,24 @@ config PPC_EARLY_DEBUG_BEAT
 	help
 	  Select this to enable early debugging for Celleb with Beat.
 
+config PPC_EARLY_DEBUG_44x
+	bool "Early serial debugging for IBM/AMCC 44x CPUs"
+	depends on 44x
+	select PPC_UDBG_16550
+	help
+	  Select this to enable early debugging for IBM 44x chips via the
+	  inbuilt serial port.
+
 endchoice
 
+config PPC_EARLY_DEBUG_44x_PHYSLOW
+	hex "Low 32 bits of early debug UART physical address"
+	depends PPC_EARLY_DEBUG_44x
+	default "0x40000200"
+
+config PPC_EARLY_DEBUG_44x_PHYSHIGH
+	hex "EPRN of early debug UART physical address"
+	depends PPC_EARLY_DEBUG_44x
+	default "0x1"
+
 endmenu

arch/powerpc/kernel/head_44x.S +13 ~~-21~~

Index: working-2.6/arch/powerpc/kernel/head_44x.S
===================================================================
@@ -172,36 +172,28 @@ skpinv:	addi	r4,r4,1				/* Increment */
 	isync
 
 4:
-#ifdef CONFIG_SERIAL_TEXT_DEBUG
-	/*
-	 * Add temporary UART mapping for early debug.
-	 * We can map UART registers wherever we want as long as they don't
-	 * interfere with other system mappings (e.g. with pinned entries).
-	 * For an example of how we handle this - see ocotea.h.       --ebs
-	 */
+#ifdef CONFIG_PPC_EARLY_DEBUG_44x
+	/* Add UART mapping for early debug. */
+
  	/* pageid fields */
-	lis	r3,UART0_IO_BASE@h
-	ori	r3,r3,PPC44x_TLB_VALID | PPC44x_TLB_4K
+	lis	r3,PPC44x_EARLY_DEBUG_VIRTADDR@h
+	ori	r3,r3,PPC44x_TLB_VALID|PPC44x_TLB_TS|PPC44x_TLB_64K
 
 	/* xlat fields */
-	lis	r4,UART0_PHYS_IO_BASE@h		/* RPN depends on SoC */
-#ifndef CONFIG_440EP
-	ori	r4,r4,0x0001		/* ERPN is 1 for second 4GB page */
-#endif
+	lis	r4,CONFIG_PPC_EARLY_DEBUG_44x_PHYSLOW@h
+	ori	r4,r4,CONFIG_PPC_EARLY_DEBUG_44x_PHYSHIGH
 
 	/* attrib fields */
-	li	r5,0
-	ori	r5,r5,(PPC44x_TLB_SW | PPC44x_TLB_SR | PPC44x_TLB_I | PPC44x_TLB_G)
-
-        li      r0,0                    /* TLB slot 0 */
+	li	r5,(PPC44x_TLB_SW|PPC44x_TLB_SR|PPC44x_TLB_I|PPC44x_TLB_G)
+        li      r0,62                    /* TLB slot 0 */
 
-	tlbwe	r3,r0,PPC44x_TLB_PAGEID	/* Load the pageid fields */
-	tlbwe	r4,r0,PPC44x_TLB_XLAT	/* Load the translation fields */
-	tlbwe	r5,r0,PPC44x_TLB_ATTRIB	/* Load the attrib/access fields */
+	tlbwe	r3,r0,PPC44x_TLB_PAGEID
+	tlbwe	r4,r0,PPC44x_TLB_XLAT
+	tlbwe	r5,r0,PPC44x_TLB_ATTRIB
 
 	/* Force context change */
 	isync
-#endif /* CONFIG_SERIAL_TEXT_DEBUG */
+#endif /* CONFIG_PPC_EARLY_DEBUG_44x */
 
 	/* Establish the interrupt vector offsets */
 	SET_IVOR(0,  CriticalInput);

arch/powerpc/kernel/udbg_16550.c +23 -0

Index: working-2.6/arch/powerpc/kernel/udbg_16550.c
===================================================================
@@ -191,3 +191,26 @@ void udbg_init_pas_realmode(void)
 	udbg_getc_poll = NULL;
 }
 #endif /* CONFIG_PPC_MAPLE */
+
+#ifdef CONFIG_PPC_EARLY_DEBUG_44x
+#include <platforms/44x/44x.h>
+
+static void udbg_44x_as1_putc(char c)
+{
+	if (udbg_comport) {
+		while ((as1_readb(&udbg_comport->lsr) & LSR_THRE) == 0)
+			/* wait for idle */;
+		as1_writeb(c, &udbg_comport->thr); eieio();
+		if (c == '\n')
+			udbg_44x_as1_putc('\r');
+	}
+}
+
+void __init udbg_init_44x_as1(void)
+{
+	udbg_comport =
+		(volatile struct NS16550 __iomem *)PPC44x_EARLY_DEBUG_VIRTADDR;
+
+	udbg_putc = udbg_44x_as1_putc;
+}
+#endif /* CONFIG_PPC_EARLY_DEBUG_44x */

include/asm-powerpc/mmu-44x.h +6 -0

Index: working-2.6/include/asm-powerpc/mmu-44x.h
===================================================================
@@ -64,7 +64,13 @@ typedef struct {
 
 #endif /* !__ASSEMBLY__ */
 
+#ifndef CONFIG_PPC_EARLY_DEBUG_44x
 #define PPC44x_EARLY_TLBS	1
+#else
+#define PPC44x_EARLY_TLBS	2
+#define PPC44x_EARLY_DEBUG_VIRTADDR	(ASM_CONST(0xf0000000) \
+	| (ASM_CONST(CONFIG_PPC_EARLY_DEBUG_44x_PHYSLOW) & 0xffff))
+#endif
 
 /* Size of the TLBs used for pinning in lowmem */
 #define PPC_PIN_SIZE	(1 << 28)	/* 256M */

arch/powerpc/kernel/udbg.c +3 -0

Index: working-2.6/arch/powerpc/kernel/udbg.c
===================================================================
@@ -51,6 +51,9 @@ void __init udbg_early_init(void)
 	udbg_init_pas_realmode();
 #elif defined(CONFIG_BOOTX_TEXT)
 	udbg_init_btext();
+#elif defined(CONFIG_PPC_EARLY_DEBUG_44x)
+	/* PPC44x debug */
+	udbg_init_44x_as1();
 #endif
 }

include/asm-powerpc/udbg.h +1 -0

Index: working-2.6/include/asm-powerpc/udbg.h
===================================================================
@@ -47,6 +47,7 @@ extern void __init udbg_init_rtas_panel(
 extern void __init udbg_init_rtas_console(void);
 extern void __init udbg_init_debug_beat(void);
 extern void __init udbg_init_btext(void);
+extern void __init udbg_init_44x_as1(void);
 
 #endif /* __KERNEL__ */
 #endif /* _ASM_POWERPC_UDBG_H */

arch/powerpc/kernel/of_platform.c +0 -1

Index: working-2.6/arch/powerpc/kernel/of_platform.c
===================================================================
@@ -29,7 +29,6 @@
 #include <asm/ppc-pci.h>
 #include <asm/atomic.h>
 
-
 /*
  * The list of OF IDs below is used for matching bus types in the
  * system whose devices are to be exposed as of_platform_devices.

arch/powerpc/platforms/44x/misc_44x.S +31 -0

Index: working-2.6/arch/powerpc/platforms/44x/misc_44x.S
===================================================================
@@ -15,6 +15,37 @@
 	.text
 
 /*
+ * Do an IO access in AS1
+ */
+_GLOBAL(as1_readb)
+	mfmsr	r7
+	ori	r0,r7,MSR_DS
+	sync
+	mtmsr	r0
+	sync
+	isync
+	lbz	r3,0(r3)
+	sync
+	mtmsr	r7
+	sync
+	isync
+	blr
+
+_GLOBAL(as1_writeb)
+	mfmsr	r7
+	ori	r0,r7,MSR_DS
+	sync
+	mtmsr	r0
+	sync
+	isync
+	stb	r3,0(r4)
+	sync
+	mtmsr	r7
+	sync
+	isync
+	blr
+
+/*
  * void ppc44x_reset_system(char *cmd)
  *
  * At present, this routine just applies a system reset.

arch/powerpc/platforms/44x/44x.h +2 -0

Index: working-2.6/arch/powerpc/platforms/44x/44x.h
===================================================================
@@ -1,6 +1,8 @@
 #ifndef __POWERPC_PLATFORMS_44X_44X_H
 #define __POWERPC_PLATFORMS_44X_44X_H
 
+extern u8 as1_readb(volatile u8 __iomem  *addr);
+extern void as1_writeb(u8 data, volatile u8 __iomem *addr);
 extern void ppc44x_reset_system(char *cmd);
 
 #endif /* __POWERPC_PLATFORMS_44X_44X_H */

David Gibson

author

2007-05-08 03:09 UTC #10 lore raw

PATCH 7/7 Device tree aware EMAC driver

In reply to David Gibson

This is BenH's rewritten, device tree aware driver for the IBM/AMCC EMAC, ethernet MAC controller ASIC found on various 4xx CPUs and also the Axon bridge. Tweaked to build on current kernels.

Signed-off-by David Gibson <[email protected]>

---

Too big for the list, download from :
http://ozlabs.org/~dgibson/home/tmp/powerpc-emac-new

 arch/powerpc/platforms/cell/Kconfig |    4 
 drivers/net/Kconfig                 |   71 
 drivers/net/Makefile                |    1 
 drivers/net/ibm_emac/Kconfig        |   63 
 drivers/net/ibm_newemac/Kconfig     |   55 
 drivers/net/ibm_newemac/Makefile    |   11 
 drivers/net/ibm_newemac/core.c      | 2912 ++++++++++++++++++++++++++++++++++++
 drivers/net/ibm_newemac/core.h      |  354 ++++
 drivers/net/ibm_newemac/debug.c     |  238 ++
 drivers/net/ibm_newemac/debug.h     |   78 
 drivers/net/ibm_newemac/emac.h      |  268 +++
 drivers/net/ibm_newemac/mal.c       |  730 +++++++++
 drivers/net/ibm_newemac/mal.h       |  276 +++
 drivers/net/ibm_newemac/phy.c       |  373 ++++
 drivers/net/ibm_newemac/phy.h       |   80 
 drivers/net/ibm_newemac/rgmii.c     |  324 ++++
 drivers/net/ibm_newemac/rgmii.h     |   76 
 drivers/net/ibm_newemac/tah.c       |  174 ++
 drivers/net/ibm_newemac/tah.h       |   90 +
 drivers/net/ibm_newemac/zmii.c      |  324 ++++
 drivers/net/ibm_newemac/zmii.h      |   73 
 21 files changed, 6514 insertions(+), 61 deletions(-)

Signature · 4 lines

David Gibson			| I'll have my music baroque, and my code
david AT gibson.dropbear.id.au	| minimalist, thank you.  NOT _the_ _other_
				| _way_ _around_!
http://www.ozlabs.org/~dgibson