ThinkPad T41 - Strange USB 2.0 behaviour
Hi,
On my ThinkPad T41 USB 2.0 behaves strange. Most USB 2.0 devices, refuse to function as such. Under Windows I get a message that I should plug the device into a USB 2.0 port (but it continues to function as USB 1.1), while under Linux I need to manually unload ehci-hcd before I can access the device.
The strange thing is that these USB 2.0 devices used to work just fine, and still do on other machines. In addition I have one USB 2.0 memory key that still works fine (both under Windows and Linux).
Now to be honest, I think this is a hardware problem, as I have had another T41p before that also suddenly no longer liked USB 2.0 devices, and if you search with Google you find other ThinkPad T41 users complaining about similar behaviour.
As such I don't really expect a fix for this (presumably) hardware issue, but what I would like is that Linux would drop back to USB 1.1 like Windows does, if for some reason USB 2.0 does not function (clearly with an appropriate message in at least syslog, perhaps even some notification with DBUS if possible).
** lspci data of USB controlers
00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 01) (prog-if 00 [UHCI])
Subsystem: IBM Thinkpad R50e model 1634
Flags: bus master, medium devsel, latency 0, IRQ 11
I/O ports at 1800 [size=32]
00: 86 80 c2 24 05 00 80 02 01 00 03 0c 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 18 00 00 00 00 00 00 00 00 00 00 14 10 2d 05
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 2f 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 60 0f 00 00 00 00 00 00
00:1d.1 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 01) (prog-if 00 [UHCI])
Subsystem: IBM Thinkpad R50e model 1634
Flags: bus master, medium devsel, latency 0, IRQ 11
I/O ports at 1820 [size=32]
00: 86 80 c4 24 05 00 80 02 01 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 21 18 00 00 00 00 00 00 00 00 00 00 14 10 2d 05
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 02 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 2f 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 60 0f 00 00 00 00 00 00
00:1d.2 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 01) (prog-if 00 [UHCI])
Subsystem: IBM Thinkpad R50e model 1634
Flags: bus master, medium devsel, latency 0, IRQ 11
I/O ports at 1840 [size=32]
00: 86 80 c7 24 05 00 80 02 01 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 41 18 00 00 00 00 00 00 00 00 00 00 14 10 2d 05
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 03 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 2f 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 60 0f 00 00 00 00 00 00
00:1d.7 USB Controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 01) (prog-if 20 [EHCI])
Subsystem: IBM Thinkpad R50e model 1634
Flags: bus master, medium devsel, latency 0, IRQ 11
Memory at c0000000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Capabilities: [58] Debug port
00: 86 80 cd 24 06 01 90 02 01 20 03 0c 00 00 00 00
10: 00 00 00 c0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 14 10 2e 05
30: 00 00 00 00 50 00 00 00 00 00 00 00 0b 04 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 01 58 c2 c9 00 00 00 00 0a 00 80 20 00 00 00 00
60: 20 20 1f 00 00 00 00 00 01 00 00 00 00 00 08 c0
70: 00 00 c7 0f 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 20 00 3f 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 78 bf 1f 00 88 83 00 00 60 0f 00 00 06 00 00 00
**errors in syslog when plugging in most USB 2.0 devices with ehci-hcd loaded (these continue until I remove the device)
Jun 7 21:41:27 localhost kernel: usb 4-4: new high speed USB device using ehci_hcd and address 11 Jun 7 21:41:27 localhost kernel: usb 4-4: new high speed USB device using ehci_hcd and address 13 Jun 7 21:41:28 localhost kernel: usb 4-4: new high speed USB device using ehci_hcd and address 18 Jun 7 21:41:32 localhost kernel: usb 4-4: new high speed USB device using ehci_hcd and address 39 Jun 7 21:41:35 localhost kernel: usb 4-4: new high speed USB device using ehci_hcd and address 60 Jun 7 21:41:36 localhost kernel: usb 4-4: new high speed USB device using ehci_hcd and address 64 Jun 7 21:41:57 localhost kernel: usb 4-4: new high speed USB device using ehci_hcd and address 91 Jun 7 21:42:01 localhost kernel: usb 4-4: new high speed USB device using ehci_hcd and address 111
**messages in syslog when plugging the only USB 2.0 device I have that actually works as such (with ehci-hcd loaded)
Jun 7 21:43:04 localhost kernel: usb 2-2: new full speed USB device using uhci_hcd and address 2 Jun 7 21:43:04 localhost kernel: usb 2-2: configuration #1 chosen from 1 choiceJun 7 21:43:05 localhost kernel: Initializing USB Mass Storage driver... Jun 7 21:43:05 localhost kernel: scsi2 : SCSI emulation for USB Mass Storage devices Jun 7 21:43:05 localhost kernel: usbcore: registered new interface driver usb-storage Jun 7 21:43:05 localhost kernel: USB Mass Storage support registered. Jun 7 21:43:10 localhost kernel: scsi 2:0:0:0: Direct-Access IBM Memory Key 3.52 PQ: 0 ANSI: 0 CCS Jun 7 21:43:10 localhost kernel: sd 2:0:0:0: [sdc] 499712 512-byte hardware sectors (256 MB) Jun 7 21:43:10 localhost kernel: sd 2:0:0:0: [sdc] Write Protect is off Jun 7 21:43:10 localhost kernel: sd 2:0:0:0: [sdc] Assuming drive cache: write through Jun 7 21:43:10 localhost kernel: sd 2:0:0:0: [sdc] 499712 512-byte hardware sectors (256 MB) Jun 7 21:43:10 localhost kernel: sd 2:0:0:0: [sdc] Write Protect is off Jun 7 21:43:10 localhost kernel: sd 2:0:0:0: [sdc] Assuming drive cache: write through Jun 7 21:43:10 localhost kernel: sdc: sdc1 Jun 7 21:43:10 localhost kernel: sd 2:0:0:0: [sdc] Attached SCSI removable diskJun 7 21:43:10 localhost kernel: sd 2:0:0:0: Attached scsi generic sg2 type 0
**lsusb output from working USB 2.0 device (with ehci-hcd loaded) Bus 004 Device 001: ID 0000:0000 Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 1 Single TT
bMaxPacketSize0 64
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.22-rc4 ehci_hcd
iProduct 2 EHCI Host Controller
iSerial 1 0000:00:1d.7
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0 Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 6
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
TT think time 8 FS bits
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0xc0
PortPwrCtrlMask 0x06
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Port 3: 0000.0100 power
Port 4: 0000.0100 power
Port 5: 0000.0100 power
Port 6: 0000.0100 power
Bus 003 Device 001: ID 0000:0000 Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.22-rc4 uhci_hcd
iProduct 2 UHCI Host Controller
iSerial 1 0000:00:1d.2
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0 Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0xc0
PortPwrCtrlMask 0x06
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Bus 002 Device 002: ID 08ec:0011 M-Systems Flash Disk Pioneers Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x08ec M-Systems Flash Disk Pioneers
idProduct 0x0011
bcdDevice 2.00
iManufacturer 1 IBM
iProduct 2 USB 2.0 Memory Key
iSerial 3 0212840B040085F0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
MaxPower 94mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI bInterfaceProtocol 80 Bulk (Zip)
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Bus 002 Device 001: ID 0000:0000 Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.22-rc4 uhci_hcd
iProduct 2 UHCI Host Controller
iSerial 1 0000:00:1d.1
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0 Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0xc0
PortPwrCtrlMask 0x06
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0103 power enable connect
Bus 001 Device 001: ID 0000:0000 Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.22-rc4 uhci_hcd
iProduct 2 UHCI Host Controller
iSerial 1 0000:00:1d.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0 Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0xc0
PortPwrCtrlMask 0x06
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
**lsusb output from USB 2.0 devices that does not work with the ehci-hcd driver loaded (cannot even see it with lsusb until ehci-hcd is unloaded) ** 128MB USB key
Bus 003 Device 001: ID 0000:0000 Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.22-rc4 uhci_hcd
iProduct 2 UHCI Host Controller
iSerial 1 0000:00:1d.2
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0 Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0xc0
PortPwrCtrlMask 0xf6
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Bus 002 Device 003: ID 0a16:9989 Trek Technology (S) PTE, Ltd Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0a16 Trek Technology (S) PTE, Ltd
idProduct 0x9989
bcdDevice 1.00
iManufacturer 1 IBM
iProduct 2 IBM USB Memory Key
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 3 0A160A1660A166
bmAttributes 0x80
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI bInterfaceProtocol 80 Bulk (Zip)
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Bus 002 Device 001: ID 0000:0000 Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.22-rc4 uhci_hcd
iProduct 2 UHCI Host Controller
iSerial 1 0000:00:1d.1
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0 Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0xc0
PortPwrCtrlMask 0xf6
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0103 power enable connect
Bus 001 Device 001: ID 0000:0000 Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.22-rc4 uhci_hcd
iProduct 2 UHCI Host Controller
iSerial 1 0000:00:1d.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0 Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0xc0
PortPwrCtrlMask 0xf6
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
** USB DVD-RW (output cut to only contain the actual device) Bus 001 Device 002: ID 0409:0056 NEC Corp.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0409 NEC Corp.
idProduct 0x0056
bcdDevice 0.00
iManufacturer 1 TSST corp
iProduct 2 USB Mass Storage Device
iSerial 3 000000000001
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 2mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 5 SFF-8070i bInterfaceProtocol 80
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
** USB HDD (output cut to only contain the actual device)
Bus 002 Device 004: ID 04cf:8818 Myson Century, Inc. Fast 3.5" External Storage Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x04cf Myson Century, Inc.
idProduct 0x8818 Fast 3.5" External Storage
bcdDevice b0.07
iManufacturer 1 Myson Century, Inc.
iProduct 2 USB Mass Storage Device
iSerial 3 100
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 4 USB Mass Storage
bmAttributes 0xc0
Self Powered
MaxPower 10mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 5 SFF-8070i bInterfaceProtocol 80
iInterface 5 Mass Storage Class
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x84 EP 4 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Quoted 6 lines · Robert de Rooy
On my ThinkPad T41 USB 2.0 behaves strange. Most USB 2.0 devices, refuse to function as such. Under Windows I get a message that I should plug the device into a USB 2.0 port (but it continues to function as USB 1.1), while under Linux I need to manually unload ehci-hcd before I can access the device.
Quoted 8 lines
The strange thing is that these USB 2.0 devices used to work just fine, and still do on other machines. In addition I have one USB 2.0 memory key that still works fine (both under Windows and Linux).
Now to be honest, I think this is a hardware problem, as I have had another T41p before that also suddenly no longer liked USB 2.0 devices, and if you search with Google you find other ThinkPad T41 users complaining about similar behaviour.
Hardware problem. You need a new system board. I had this
problem on my T41, devices would sometimes work, sometimes not (depending on the reboot). If I plugged in a USB 1.1 hub, then pluged the memory reader into the hub, it would always work at 1.1 speeds.
New system board, USB 2.0 works just fine.
Joel
Signature · 9 lines
Life's Little Instruction Book #274 "Leave everything a little better than you found it." Joel Becker Principal Software Developer Oracle E-mail: [email protected] Phone: (650) 506-8127
Quoted 9 lines · Joel Becker
Quoted 6 lines · Robert de Rooy
On my ThinkPad T41 USB 2.0 behaves strange. Most USB 2.0 devices, refuse to function as such. Under Windows I get a message that I should plug the device into a USB 2.0 port (but it continues to function as USB 1.1), while under Linux I need to manually unload ehci-hcd before I can access the device.
The strange thing is that these USB 2.0 devices used to work just fine, and still do on other machines. In addition I have one USB 2.0 memory key that still works fine (both under Windows and Linux).
Now to be honest, I think this is a hardware problem, as I have had another T41p before that also suddenly no longer liked USB 2.0 devices, and if you search with Google you find other ThinkPad T41 users complaining about similar behaviour.
Quoted 8 lines
Hardware problem. You need a new system board. I had this
problem on my T41, devices would sometimes work, sometimes not (depending on the reboot). If I plugged in a USB 1.1 hub, then pluged the memory reader into the hub, it would always work at 1.1 speeds.
New system board, USB 2.0 works just fine.Joel
Yes I figured it was a hardware problem, but that was not really the point I was trying to raise ;). I would like, if possible for Linux to automatically fallback to USB 1.1 like Windows does (preferably with a suitable warning).
Regarding getting the systemboard replaced, this machine is already scheduled for replacement, and I should be getting a new one in the next few weeks. But other users apparently have been having similar problems, and might not want to get the (presumably out-of-warranty) systemboard replaced.
Quoted 4 lines · Robert de Rooy
Yes I figured it was a hardware problem, but that was not really the point I was trying to raise ;). I would like, if possible for Linux to automatically fallback to USB 1.1 like Windows does (preferably with a suitable warning).
Oh, I see. I thought you were saying "I suspect it is hardware,
but maybe it isn't?" The sure workaround is a USB 1.1 hub, but having linux detect would be cool.
Joel
Signature · 8 lines
"Vote early and vote often."
- Al Capone
Joel Becker
Principal Software Developer
Oracle
E-mail: [email protected]
Phone: (650) 506-8127Quoted 4 lines · Robert de Rooy
Yes I figured it was a hardware problem, but that was not really the point I was trying to raise ;). I would like, if possible for Linux to automatically fallback to USB 1.1 like Windows does (preferably with a suitable warning).
What do you propose as a trigger for the kernel to fallback?
You can work it around manually, just don't use ehci-hcd, can't you?
Signature · 1 line
Jiri Kosina
Quoted 11 lines · Jiri Kosina
Quoted 2 lines · Robert de Rooy
Yes I figured it was a hardware problem, but that was not really the point I was trying to raise ;). I would like, if possible for Linux to automatically fallback to USB 1.1 like Windows does (preferably with a suitable warning).
What do you propose as a trigger for the kernel to fallback?
You can work it around manually, just don't use ehci-hcd, can't you?
Yes I can unload ehci-hcd, but I have one USB 2.0 device that strangely enough DOES work as such, and unloading ehci-hcd will cause that also to run at 1.1 speed.
Clearly something is failing when plugging a device with ehci-hcd loaded, the driver seems to keep retrying indefinitely. Instead it would be nice if after a few tries it hands the device over to uhci-hcd. This seems to be the behaviour under Windows, so I was wondering if Linux could be made to do something similar.
linux-usb-devel list added
Quoted 26 lines · Robert de Rooy
Quoted 9 lines · Jiri Kosina
Quoted 5 lines · Robert de Rooy
Yes I figured it was a hardware problem, but that was not really the point I was trying to raise ;). I would like, if possible for Linux to automatically fallback to USB 1.1 like Windows does (preferably with a suitable warning).
Quoted 5 lines
What do you propose as a trigger for the kernel to fallback?
You can work it around manually, just don't use ehci-hcd, can't you?
Yes I can unload ehci-hcd, but I have one USB 2.0 device that strangely enough DOES work as such, and unloading ehci-hcd will cause that also to run at 1.1 speed.
Clearly something is failing when plugging a device with ehci-hcd loaded, the driver seems to keep retrying indefinitely. Instead it would be nice if after a few tries it hands the device over to uhci-hcd. This seems to be the behaviour under Windows, so I was wondering if Linux could be made to do something similar.
Signature · 1 line
Jiri Kosina
Quoted 28 lines · Jiri Kosina
linux-usb-devel list added
Quoted 24 lines · Robert de Rooy
Quoted 9 lines · Jiri Kosina
Quoted 5 lines · Robert de Rooy
Yes I figured it was a hardware problem, but that was not really the point I was trying to raise ;). I would like, if possible for Linux to automatically fallback to USB 1.1 like Windows does (preferably with a suitable warning).
Quoted 5 lines
What do you propose as a trigger for the kernel to fallback?
You can work it around manually, just don't use ehci-hcd, can't you?
Yes I can unload ehci-hcd, but I have one USB 2.0 device that strangely enough DOES work as such, and unloading ehci-hcd will cause that also to run at 1.1 speed.
Clearly something is failing when plugging a device with ehci-hcd loaded, the driver seems to keep retrying indefinitely. Instead it would be nice if after a few tries it hands the device over to uhci-hcd. This seems to be the behaviour under Windows, so I was wondering if Linux could be made to do something similar.
Robert, it would help somewhat if you could build a kernel with CONFIG_USB_DEBUG turned on and post the dmesg log showing what happens when you plug in one of those non-working devices.
Yes, in principle Linux can be made to switch over to full speed when high speed fails. But there are limitations: The switchover would work only for devices plugged directly into the computer, not for devices plugged into a high-speed hub. And some Linux systems (not regular PCs) have EHCI implementations that don't allow such a switch -- or if they do, I'm not aware of how to accomplish it.
BTW, depending on the kind of failure the system does not keep retrying indefinitely. It gives up after four attempts.
Alan Stern
Quoted 2 lines · Alan Stern
Robert, it would help somewhat if you could build a kernel with
CONFIG_USB_DEBUGturned on and post the dmesg log showing what happens when you plug in one of those non-working devices.
Sorry, yes I should have done that before...
Quoted 2 lines
Yes, in principle Linux can be made to switch over to full speed when high speed fails. But there are limitations: The switchover would work only for devices plugged directly into the computer, not for devices plugged into a high-speed hub. And some Linux systems (not regular PCs) have EHCI implementations that don't allow such a switch -- or if they do, I'm not aware of how to accomplish it.
Interesting, I have a USB 2.0 hub, but have not tried it, mainly because I need to find a power supply for it first.
But regardless if the hub works as USB 2.0 or 1.1, it could be that another hub behaves differently, just like I have one USB 2.0 memory key that still works as such.
Quoted 3 lines
BTW, depending on the kind of failure the system does not keep retrying indefinitely. It gives up after four attempts.
Alan Stern
***USB related boot messages with CONFIG_USB_DEBUG enabled
Jun 8 23:33:30 localhost kernel: USB Universal Host Controller Interface driver v3.0 Jun 8 23:33:30 localhost kernel: ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 Jun 8 23:33:30 localhost kernel: uhci_hcd 0000:00:1d.0: UHCI Host Controller Jun 8 23:33:30 localhost kernel: uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 Jun 8 23:33:30 localhost kernel: uhci_hcd 0000:00:1d.0: detected 2 ports Jun 8 23:33:30 localhost kernel: uhci_hcd 0000:00:1d.0: irq 11, io base 0x00001800 Jun 8 23:33:30 localhost kernel: usb usb1: Product: UHCI Host Controller Jun 8 23:33:30 localhost kernel: usb usb1: Manufacturer: Linux 2.6.22-rc4 uhci_hcd Jun 8 23:33:30 localhost kernel: usb usb1: SerialNumber: 0000:00:1d.0 Jun 8 23:33:30 localhost kernel: usb usb1: configuration #1 chosen from 1 choice Jun 8 23:33:30 localhost kernel: hub 1-0:1.0: USB hub found Jun 8 23:33:30 localhost kernel: hub 1-0:1.0: 2 ports detected Jun 8 23:33:30 localhost kernel: ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11 Jun 8 23:33:30 localhost kernel: ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11 Jun 8 23:33:30 localhost kernel: uhci_hcd 0000:00:1d.1: UHCI Host Controller Jun 8 23:33:30 localhost kernel: uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 Jun 8 23:33:30 localhost kernel: uhci_hcd 0000:00:1d.1: detected 2 ports Jun 8 23:33:30 localhost kernel: uhci_hcd 0000:00:1d.1: irq 11, io base 0x00001820 Jun 8 23:33:30 localhost kernel: usb usb2: Product: UHCI Host Controller Jun 8 23:33:30 localhost kernel: usb usb2: Manufacturer: Linux 2.6.22-rc4 uhci_hcd Jun 8 23:33:30 localhost kernel: usb usb2: SerialNumber: 0000:00:1d.1 Jun 8 23:33:31 localhost kernel: usb usb2: configuration #1 chosen from 1 choice Jun 8 23:33:31 localhost rpcbind: cannot create socket for udp6 Jun 8 23:33:31 localhost kernel: hub 2-0:1.0: USB hub found Jun 8 23:33:31 localhost kernel: hub 2-0:1.0: 2 ports detected Jun 8 23:33:31 localhost rpcbind: cannot create socket for tcp6 Jun 8 23:33:31 localhost kernel: ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11 Jun 8 23:33:31 localhost kernel: ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11 Jun 8 23:33:31 localhost kernel: uhci_hcd 0000:00:1d.2: UHCI Host Controller Jun 8 23:33:31 localhost kernel: uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 Jun 8 23:33:31 localhost kernel: uhci_hcd 0000:00:1d.2: detected 2 ports Jun 8 23:33:31 localhost kernel: uhci_hcd 0000:00:1d.2: irq 11, io base 0x00001840 Jun 8 23:33:31 localhost kernel: usb usb3: Product: UHCI Host Controller Jun 8 23:33:31 localhost kernel: usb usb3: Manufacturer: Linux 2.6.22-rc4 uhci_hcd Jun 8 23:33:31 localhost kernel: usb usb3: SerialNumber: 0000:00:1d.2 Jun 8 23:33:31 localhost kernel: usb usb3: configuration #1 chosen from 1 choice Jun 8 23:33:31 localhost kernel: hub 3-0:1.0: USB hub found Jun 8 23:33:31 localhost kernel: hub 3-0:1.0: 2 ports detected Jun 8 23:33:31 localhost kernel: ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11 Jun 8 23:33:31 localhost kernel: ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11 Jun 8 23:33:31 localhost kernel: ehci_hcd 0000:00:1d.7: EHCI Host Controller Jun 8 23:33:31 localhost kernel: ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4 Jun 8 23:33:31 localhost kernel: ehci_hcd 0000:00:1d.7: debug port 1 Jun 8 23:33:31 localhost kernel: ehci_hcd 0000:00:1d.7: irq 11, io mem 0xc0000000 Jun 8 23:33:31 localhost kernel: ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 Jun 8 23:33:31 localhost kernel: usb usb4: Product: EHCI Host Controller Jun 8 23:33:31 localhost kernel: usb usb4: Manufacturer: Linux 2.6.22-rc4 ehci_hcd Jun 8 23:33:31 localhost kernel: usb usb4: SerialNumber: 0000:00:1d.7 Jun 8 23:33:31 localhost kernel: usb usb4: configuration #1 chosen from 1 choice Jun 8 23:33:31 localhost kernel: hub 4-0:1.0: USB hub found
*** Plug USB 2.0 128MB memory key (with ehci-hcd loaded)
Jun 8 23:35:14 localhost kernel: usb 4-4: new high speed USB device using ehci_hcd and address 14 Jun 8 23:35:18 localhost kernel: usb 4-4: new high speed USB device using ehci_hcd and address 35 Jun 8 23:35:19 localhost kernel: usb 4-4: new high speed USB device using ehci_hcd and address 39 Jun 8 23:35:19 localhost kernel: ehci_hcd 0000:00:1d.7: port 4 reset error -110 Jun 8 23:35:19 localhost kernel: hub 4-0:1.0: hub_port_status failed (err = -32) Jun 8 23:35:19 localhost kernel: ehci_hcd 0000:00:1d.7: port 4 reset error -110 Jun 8 23:35:19 localhost kernel: hub 4-0:1.0: hub_port_status failed (err = -32) Jun 8 23:35:19 localhost kernel: hub 4-0:1.0: Cannot enable port 4. Maybe the USB cable is bad? Jun 8 23:35:19 localhost kernel: ehci_hcd 0000:00:1d.7: port 4 reset error -110 Jun 8 23:35:19 localhost kernel: hub 4-0:1.0: hub_port_status failed (err = -32) Jun 8 23:35:22 localhost kernel: usb 4-4: new high speed USB device using ehci_hcd and address 55 Jun 8 23:35:23 localhost kernel: usb 4-4: new high speed USB device using ehci_hcd and address 56 Jun 8 23:35:23 localhost kernel: usb 4-4: new high speed USB device using ehci_hcd and address 60 Jun 8 23:35:24 localhost kernel: usb 4-4: new high speed USB device using ehci_hcd and address 66 Jun 8 23:35:25 localhost kernel: usb 4-4: new high speed USB device using ehci_hcd and address 69 Jun 8 23:35:28 localhost kernel: usb 4-4: new high speed USB device using ehci_hcd and address 87 Jun 8 23:35:28 localhost kernel: usb 4-4: new high speed USB device using ehci_hcd and address 88 Jun 8 23:35:29 localhost kernel: usb 4-4: new high speed USB device using ehci_hcd and address 93 Jun 8 23:35:29 localhost kernel: usb 4-4: new high speed USB device using ehci_hcd and address 95 Jun 8 23:35:31 localhost kernel: usb 4-4: new high speed USB device using ehci_hcd and address 105 Jun 8 23:35:35 localhost kernel: usb 4-4: new high speed USB device using ehci_hcd and address 3 Jun 8 23:35:36 localhost kernel: usb 4-4: new high speed USB device using ehci_hcd and address 11 Jun 8 23:35:37 localhost kernel: usb 4-4: new high speed USB device using ehci_hcd and address 16 Jun 8 23:35:38 localhost kernel: usb 4-4: new high speed USB device using ehci_hcd and address 18 Jun 8 23:35:40 localhost kernel: usb 4-4: new high speed USB device using ehci_hcd and address 31 Jun 8 23:35:41 localhost kernel: usb 4-4: new high speed USB device using ehci_hcd and address 36 Jun 8 23:35:42 localhost kernel: usb 4-4: new high speed USB device using ehci_hcd and address 43 Jun 8 23:35:43 localhost kernel: usb 4-4: new high speed USB device using ehci_hcd and address 49 Jun 8 23:35:44 localhost kernel: usb 4-4: new high speed USB device using ehci_hcd and address 55 Jun 8 23:35:44 localhost kernel: ehci_hcd 0000:00:1d.7: port 4 reset error -110 Jun 8 23:35:44 localhost kernel: hub 4-0:1.0: hub_port_status failed (err = -32) Jun 8 23:35:45 localhost kernel: usb 4-4: new high speed USB device using ehci_hcd and address 58 Jun 8 23:35:46 localhost kernel: usb 4-4: new high speed USB device using ehci_hcd and address 59 Jun 8 23:35:50 localhost kernel: usb 4-4: new high speed USB device using ehci_hcd and address 87 Jun 8 23:35:51 localhost kernel: usb 4-4: new high speed USB device using ehci_hcd and address 92 Jun 8 23:35:52 localhost kernel: usb 4-4: new high speed USB device using ehci_hcd and address 99 Jun 8 23:35:53 localhost kernel: ehci_hcd 0000:00:1d.7: port 4 reset error -110 Jun 8 23:35:53 localhost kernel: hub 4-0:1.0: hub_port_status failed (err = -32) Jun 8 23:35:54 localhost kernel: usb 4-4: new high speed USB device using ehci_hcd and address 105 Jun 8 23:35:54 localhost kernel: usb 4-4: new high speed USB device using ehci_hcd and address 106 Jun 8 23:35:54 localhost kernel: ehci_hcd 0000:00:1d.7: port 4 reset error -110 Jun 8 23:35:54 localhost kernel: hub 4-0:1.0: hub_port_status failed (err = -32) Jun 8 23:35:56 localhost kernel: usb 4-4: new high speed USB device using ehci_hcd and address 112 Jun 8 23:35:58 localhost kernel: usb 4-4: new high speed USB device using ehci_hcd and address 122
*** unplug USB key, rmmod ehci-hcd
Jun 8 23:36:26 localhost kernel: ehci_hcd 0000:00:1d.7: remove, state 4 Jun 8 23:36:26 localhost kernel: usb usb4: USB disconnect, address 1 Jun 8 23:36:26 localhost kernel: ehci_hcd 0000:00:1d.7: USB bus 4 deregistered Jun 8 23:36:26 localhost kernel: ACPI: PCI interrupt for device 0000:00:1d.7 disabled
*** plug USB key (without ehci-hcd)
Jun 8 23:36:41 localhost kernel: usb 2-2: new full speed USB device using uhci_hcd and address 2 Jun 8 23:36:41 localhost kernel: usb 2-2: Product: IBM USB Memory Key Jun 8 23:36:41 localhost kernel: usb 2-2: Manufacturer: IBM Jun 8 23:36:41 localhost kernel: usb 2-2: configuration #1 chosen from 1 choice Jun 8 23:36:41 localhost kernel: Initializing USB Mass Storage driver... Jun 8 23:36:41 localhost kernel: scsi2 : SCSI emulation for USB Mass Storage devices Jun 8 23:36:41 localhost kernel: usbcore: registered new interface driver usb-storage Jun 8 23:36:41 localhost kernel: USB Mass Storage support registered. Jun 8 23:36:46 localhost kernel: scsi 2:0:0:0: Direct-Access IBM Memory Key 1.01 PQ: 0 ANSI: 0 CCS Jun 8 23:36:46 localhost kernel: sd 2:0:0:0: [sdc] Attached SCSI removable disk Jun 8 23:36:46 localhost kernel: sd 2:0:0:0: Attached scsi generic sg2 type 0 Jun 8 23:36:47 localhost kernel: sd 2:0:0:0: [sdc] 256000 512-byte hardware sectors (131 MB) Jun 8 23:36:47 localhost kernel: sd 2:0:0:0: [sdc] Write Protect is off Jun 8 23:36:47 localhost kernel: sd 2:0:0:0: [sdc] Assuming drive cache: write through Jun 8 23:36:47 localhost kernel: sd 2:0:0:0: [sdc] 256000 512-byte hardware sectors (131 MB) Jun 8 23:36:47 localhost kernel: sd 2:0:0:0: [sdc] Write Protect is off Jun 8 23:36:47 localhost kernel: sd 2:0:0:0: [sdc] Assuming drive cache: write through Jun 8 23:36:47 localhost kernel: sdc: sdc1 Jun 8 23:36:48 localhost hald: mounted /dev/sdc1 on behalf of uid 0
Quoted 6 lines · Robert de Rooy
Quoted 4 lines · Alan Stern
Robert, it would help somewhat if you could build a kernel with
CONFIG_USB_DEBUGturned on and post the dmesg log showing what happens when you plug in one of those non-working devices.Sorry, yes I should have done that before...
Unfortunately you posted the system log file instead of the dmesg log, and your syslogd was configured not to retain debug-level messages.
Quoted 7 lines
Quoted 7 lines
Yes, in principle Linux can be made to switch over to full speed when high speed fails. But there are limitations: The switchover would work only for devices plugged directly into the computer, not for devices plugged into a high-speed hub. And some Linux systems (not regular PCs) have EHCI implementations that don't allow such a switch -- or if they do, I'm not aware of how to accomplish it.
Quoted 5 lines
Interesting, I have a USB 2.0 hub, but have not tried it, mainly because I need to find a power supply for it first.
But regardless if the hub works as USB 2.0 or 1.1, it could be that another hub behaves differently, just like I have one USB 2.0 memory key that still works as such.
You did not understand my point. Regardless of how the hub behaves, there is no way to tell it that a device plugged into a particular port should not be allowed to run at high speed.
Alan Stern
Quoted 2 lines · Alan Stern
Unfortunately you posted the system log file instead of the dmesg log, and your syslogd was configured not to retain debug-level messages.
Ok, I did not realize my syslog was filtering the debug-level messages, here is the output from dmesg
***USB related boot messages
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.0 to 64uhci_hcd 0000:00:1d.0: UHCI Host Controllerdrivers/usb/core/inode.c: creating file 'devices' drivers/usb/core/inode.c: creating file '001'uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:1d.0: detected 2 portsuhci_hcd 0000:00:1d.0: uhci_check_and_reset_hc: cmd = 0x0000uhci_hcd 0000:00:1d.0: Performing full resetuhci_hcd 0000:00:1d.0: irq 11, io base 0x00001800
usb usb1: default language 0x0409
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.22-rc4 uhci_hcd
usb usb1: SerialNumber: 0000:00:1d.0
PM: Adding info for usb:usb1
usb usb1: uevent
usb usb1: usb_probe_device
PM: Adding info for No Bus:usbdev1.1_ep00
usb usb1: configuration #1 chosen from 1 choice
usb usb1: adding 1-0:1.0 (config #1, interface 0)
PM: Adding info for usb:1-0:1.0
usb 1-0:1.0: uevent
usb 1-0:1.0: uevent
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: power on to power good time: 2ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: trying to enable port power on non-switchable hub
hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0000
PM: Adding info for No Bus:usbdev1.1_ep81drivers/usb/core/inode.c: creating file '001'
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.1 to 64uhci_hcd 0000:00:1d.1: UHCI Host Controllerdrivers/usb/core/inode.c: creating file '002'uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1d.1: detected 2 portsuhci_hcd 0000:00:1d.1: uhci_check_and_reset_hc: cmd = 0x0000uhci_hcd 0000:00:1d.1: Performing full resetuhci_hcd 0000:00:1d.1: irq 11, io base 0x00001820
usb usb2: default language 0x0409
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.22-rc4 uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.1
PM: Adding info for usb:usb2
usb usb2: uevent
usb usb2: usb_probe_device
PM: Adding info for No Bus:usbdev2.1_ep00
usb usb2: configuration #1 chosen from 1 choice
usb usb2: adding 2-0:1.0 (config #1, interface 0)
PM: Adding info for usb:2-0:1.0
usb 2-0:1.0: uevent
usb 2-0:1.0: uevent
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: individual port over-current protection
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: local power source is good
hub 2-0:1.0: trying to enable port power on non-switchable hub
hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0000
PM: Adding info for No Bus:usbdev2.1_ep81drivers/usb/core/inode.c: creating file '001'
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.2 to 64uhci_hcd 0000:00:1d.2: UHCI Host Controllerdrivers/usb/core/inode.c: creating file '003'uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.2: detected 2 portsuhci_hcd 0000:00:1d.2: uhci_check_and_reset_hc: cmd = 0x0000uhci_hcd 0000:00:1d.2: Performing full resetuhci_hcd 0000:00:1d.2: irq 11, io base 0x00001840
usb usb3: default language 0x0409
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.22-rc4 uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.2
PM: Adding info for usb:usb3
usb usb3: uevent
usb usb3: usb_probe_device
PM: Adding info for No Bus:usbdev3.1_ep00
usb usb3: configuration #1 chosen from 1 choice
usb usb3: adding 3-0:1.0 (config #1, interface 0)
PM: Adding info for usb:3-0:1.0
usb 3-0:1.0: uevent
usb 3-0:1.0: uevent
hub 3-0:1.0: usb_probe_interface
hub 3-0:1.0: usb_probe_interface - got id
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
hub 3-0:1.0: standalone hub
hub 3-0:1.0: no power switching (usb 1.0)
hub 3-0:1.0: individual port over-current protection
hub 3-0:1.0: power on to power good time: 2ms
hub 3-0:1.0: local power source is good
hub 3-0:1.0: trying to enable port power on non-switchable hub
hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000
PM: Adding info for No Bus:usbdev3.1_ep81drivers/usb/core/inode.c: creating file '001'ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driverohci_hcd: block sizes: ed 64 td 64ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.7 to 64ehci_hcd 0000:00:1d.7: EHCI Host Controllerdrivers/usb/core/inode.c: creating file '004'ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4 ehci_hcd 0000:00:1d.7: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6 ehci_hcd 0000:00:1d.7: reset hcc_params 6871 thresh 7 uframes 1024 64 bit addr ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: supports USB remote wakeupehci_hcd 0000:00:1d.7: irq 11, io mem 0xc0000000ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT ehci_hcd 0000:00:1d.7: init command 010001 (park)=0 ithresh=1 period=1024 RUN ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb4: default language 0x0409
usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: EHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.22-rc4 ehci_hcd
usb usb4: SerialNumber: 0000:00:1d.7
PM: Adding info for usb:usb4
usb usb4: uevent
usb usb4: usb_probe_device
PM: Adding info for No Bus:usbdev4.1_ep00
usb usb4: configuration #1 chosen from 1 choice
usb usb4: adding 4-0:1.0 (config #1, interface 0)
PM: Adding info for usb:4-0:1.0
usb 4-0:1.0: uevent
usb 4-0:1.0: uevent
hub 4-0:1.0: usb_probe_interface
hub 4-0:1.0: usb_probe_interface - got id
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
hub 4-0:1.0: standalone hub
hub 4-0:1.0: no power switching (usb 1.0)
hub 4-0:1.0: individual port over-current protection
hub 4-0:1.0: Single TT
hub 4-0:1.0: TT requires at most 8 FS bit times (666 ns)
hub 4-0:1.0: power on to power good time: 20ms
hub 4-0:1.0: local power source is good
hub 4-0:1.0: trying to enable port power on non-switchable hub
usb usb1: suspend_rh (auto-stop)
usb usb2: suspend_rh (auto-stop)
usb usb3: suspend_rh (auto-stop)
Clocksource tsc unstable (delta = -65524005 ns)
hub 1-0:1.0: hub_suspend
usb usb1: suspend_rh
usb usb1: usb auto-suspend
hub 2-0:1.0: hub_suspend
usb usb2: suspend_rh
usb usb2: usb auto-suspend
hub 3-0:1.0: hub_suspend
usb usb3: suspend_rh
usb usb3: usb auto-suspend
hub 4-0:1.0: hub_suspendehci_hcd 0000:00:1d.7: suspend root hub
usb usb4: usb auto-suspend
usb usb1: uevent
usb 1-0:1.0: uevent
usb 1-0:1.0: uevent
usb usb2: uevent
usb 2-0:1.0: uevent
usb 2-0:1.0: uevent
usb usb3: uevent
usb 3-0:1.0: uevent
usb 3-0:1.0: uevent
usb usb4: uevent
usb 4-0:1.0: uevent
usb 4-0:1.0: uevent
usb usb4: usb auto-resume
usb usb4: finish resume
hub 4-0:1.0: hub_resumeehci_hcd 0000:00:1d.7: resume root hub
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0000 usb usb3: usb auto-resume
usb usb3: finish resume
hub 3-0:1.0: hub_resume
usb usb3: wakeup_rh
hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000 usb usb2: usb auto-resume
usb usb2: finish resume
hub 2-0:1.0: hub_resume
usb usb2: wakeup_rh
hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0000 usb usb1: usb auto-resume
usb usb1: finish resume
hub 1-0:1.0: hub_resume
usb usb1: wakeup_rh
hub 1-0:1.0: state 7 ports 2 chg 0000 evt 0000 usb usb3: suspend_rh (auto-stop)
usb usb2: suspend_rh (auto-stop)
usb usb1: suspend_rh (auto-stop)
Bluetooth: HIDP (Human Interface Emulation) ver 1.2 hub 4-0:1.0: hub_suspendehci_hcd 0000:00:1d.7: suspend root hub
usb usb4: usb auto-suspend
hub 3-0:1.0: hub_suspend
usb usb3: suspend_rh
usb usb3: usb auto-suspend
hub 2-0:1.0: hub_suspend
usb usb2: suspend_rh
usb usb2: usb auto-suspend
hub 1-0:1.0: hub_suspend
usb usb1: suspend_rh
usb usb1: usb auto-suspend
*** plugging device (leaving it in slightly to long, hence the long log); removing the device; rmmod ehci-hcd; plug back in usb usb4: usb resume
usb usb4: finish resume
hub 4-0:1.0: hub_resumeehci_hcd 0000:00:1d.7: resume root hub
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0000ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: port 4 high speedehci_hcd 0000:00:1d.7: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT
usb 4-4: new high speed USB device using ehci_hcd and address 2ehci_hcd 0000:00:1d.7: devpath 4 ep0in 3strikesehci_hcd 0000:00:1d.7: devpath 4 ep0in 3strikesehci_hcd 0000:00:1d.7: devpath 4 ep0in 3strikesehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: port 4 high speedehci_hcd 0000:00:1d.7: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT
usb 4-4: new high speed USB device using ehci_hcd and address 15ehci_hcd 0000:00:1d.7: devpath 4 ep0in 3strikesehci_hcd 0000:00:1d.7: devpath 4 ep0in 3strikesehci_hcd 0000:00:1d.7: devpath 4 ep0in 3strikesehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: port 4 high speedehci_hcd 0000:00:1d.7: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT
usb 4-4: new high speed USB device using ehci_hcd and address 20ehci_hcd 0000:00:1d.7: devpath 4 ep0in 3strikesehci_hcd 0000:00:1d.7: devpath 4 ep0in 3strikesehci_hcd 0000:00:1d.7: devpath 4 ep0in 3strikesehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: port 4 high speedehci_hcd 0000:00:1d.7: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT
usb 4-4: new high speed USB device using ehci_hcd and address 38ehci_hcd 0000:00:1d.7: devpath 4 ep0in 3strikesehci_hcd 0000:00:1d.7: devpath 4 ep0in 3strikesehci_hcd 0000:00:1d.7: devpath 4 ep0in 3strikesehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: port 4 high speedehci_hcd 0000:00:1d.7: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT
usb 4-4: new high speed USB device using ehci_hcd and address 43ehci_hcd 0000:00:1d.7: devpath 4 ep0in 3strikesehci_hcd 0000:00:1d.7: devpath 4 ep0in 3strikesehci_hcd 0000:00:1d.7: devpath 4 ep0in 3strikesehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001004 POWER sig=se0 PE
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: port 4 high speedehci_hcd 0000:00:1d.7: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT
usb 4-4: new high speed USB device using ehci_hcd and address 49ehci_hcd 0000:00:1d.7: devpath 4 ep0in 3strikesehci_hcd 0000:00:1d.7: devpath 4 ep0in 3strikesehci_hcd 0000:00:1d.7: devpath 4 ep0in 3strikesehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: port 4 high speedehci_hcd 0000:00:1d.7: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT
usb 4-4: new high speed USB device using ehci_hcd and address 53ehci_hcd 0000:00:1d.7: devpath 4 ep0in 3strikesehci_hcd 0000:00:1d.7: devpath 4 ep0in 3strikesehci_hcd 0000:00:1d.7: devpath 4 ep0in 3strikesehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: port 4 high speedehci_hcd 0000:00:1d.7: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT
usb 4-4: new high speed USB device using ehci_hcd and address 62ehci_hcd 0000:00:1d.7: devpath 4 ep0in 3strikesehci_hcd 0000:00:1d.7: devpath 4 ep0in 3strikesehci_hcd 0000:00:1d.7: devpath 4 ep0in 3strikesehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001004 POWER sig=se0 PE
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: port 4 high speedehci_hcd 0000:00:1d.7: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT
usb 4-4: new high speed USB device using ehci_hcd and address 95ehci_hcd 0000:00:1d.7: devpath 4 ep0in 3strikesehci_hcd 0000:00:1d.7: devpath 4 ep0in 3strikesehci_hcd 0000:00:1d.7: devpath 4 ep0in 3strikesehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: port 4 high speedehci_hcd 0000:00:1d.7: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT
usb 4-4: new high speed USB device using ehci_hcd and address 110ehci_hcd 0000:00:1d.7: devpath 4 ep0in 3strikesehci_hcd 0000:00:1d.7: devpath 4 ep0in 3strikesehci_hcd 0000:00:1d.7: devpath 4 ep0in 3strikesehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: port 4 high speedehci_hcd 0000:00:1d.7: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT
usb 4-4: new high speed USB device using ehci_hcd and address 117ehci_hcd 0000:00:1d.7: devpath 4 ep0in 3strikesehci_hcd 0000:00:1d.7: devpath 4 ep0in 3strikesehci_hcd 0000:00:1d.7: devpath 4 ep0in 3strikesehci_hcd 0000:00:1d.7: port 4 high speedehci_hcd 0000:00:1d.7: GetStatus port 4 status 001007 POWER sig=se0 PE CSC CONNECT
hub 4-0:1.0: port_wait_reset: err = -22
hub 4-0:1.0: port 4 not enabled, trying reset again...ehci_hcd 0000:00:1d.7: port 4 reset error -110
hub 4-0:1.0: hub_port_status failed (err = -32)
hub 4-0:1.0: port_wait_reset: err = -32
hub 4-0:1.0: port 4 not enabled, trying reset again...ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port_wait_reset: err = -22
hub 4-0:1.0: port 4 not enabled, trying reset again...ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: hub_suspendehci_hcd 0000:00:1d.7: suspend root hub
usb usb4: usb auto-suspendehci_hcd 0000:00:1d.7: remove, state 4ehci_hcd 0000:00:1d.7: roothub graceful disconnect
usb usb4: USB disconnect, address 1
usb usb4: unregistering device
usb usb4: usb_disable_device nuking all URBs
usb usb4: unregistering interface 4-0:1.0
PM: Removing info for No Bus:usbdev4.1_ep81usb_endpoint usbdev4.1_ep81: ep_device_release called for usbdev4.1_ep81
PM: Removing info for usb:4-0:1.0
usb 4-0:1.0: uevent
usb 4-0:1.0: uevent
PM: Removing info for No Bus:usbdev4.1_ep00usb_endpoint usbdev4.1_ep00: ep_device_release called for usbdev4.1_ep00
PM: Removing info for usb:usb4
usb usb4: ueventehci_hcd 0000:00:1d.7: stopehci_hcd 0000:00:1d.7: reset command 010002 (park)=0 ithresh=1 period=1024 Reset HALTehci_hcd 0000:00:1d.7: irq normal 0 err 33 reclaim 33 (lost 0)ehci_hcd 0000:00:1d.7: complete 33 unlink 0ehci_hcd 0000:00:1d.7: ehci_stop completed status 1000 Haltehci_hcd 0000:00:1d.7: USB bus 4 deregistered
ACPI: PCI interrupt for device 0000:00:1d.7 disabled
usb usb2: usb resume
usb usb2: finish resume
hub 2-0:1.0: hub_resume
usb usb2: wakeup_rh
hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0000uhci_hcd 0000:00:1d.1: port 2 portsc 0093,00
hub 2-0:1.0: port 2, status 0101, change 0001, 12 Mb/s
hub 2-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x101
usb 2-2: new full speed USB device using uhci_hcd and address 2
usb 2-2: default language 0x0409
usb 2-2: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-2: Product: IBM USB Memory Key
usb 2-2: Manufacturer: IBM
PM: Adding info for usb:2-2
usb 2-2: uevent
usb 2-2: usb_probe_device
PM: Adding info for No Bus:usbdev2.2_ep00
usb 2-2: configuration #1 chosen from 1 choice
usb 2-2: adding 2-2:1.0 (config #1, interface 0)
PM: Adding info for usb:2-2:1.0
usb 2-2:1.0: uevent
usb 2-2:1.0: uevent
libusual 2-2:1.0: usb_probe_interface
libusual 2-2:1.0: usb_probe_interface - got id
PM: Adding info for No Bus:usbdev2.2_ep01
PM: Adding info for No Bus:usbdev2.2_ep82drivers/usb/core/inode.c: creating file '002'
hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0004
Initializing USB Mass Storage driver...
usb-storage 2-2:1.0: usb_probe_interface
usb-storage 2-2:1.0: usb_probe_interface - got id
scsi2 : SCSI emulation for USB Mass Storage devices
PM: Adding info for No Bus:host2
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device scan complete
PM: Adding info for No Bus:target2:0:0
scsi 2:0:0:0: Direct-Access IBM Memory Key 1.01 PQ: 0 ANSI: 0 CCS
PM: Adding info for No Bus:target2:0:1
PM: Removing info for No Bus:target2:0:1
PM: Adding info for No Bus:target2:0:2
PM: Removing info for No Bus:target2:0:2
PM: Adding info for No Bus:target2:0:3
PM: Removing info for No Bus:target2:0:3
PM: Adding info for No Bus:target2:0:4
PM: Removing info for No Bus:target2:0:4
PM: Adding info for No Bus:target2:0:5
PM: Removing info for No Bus:target2:0:5
PM: Adding info for No Bus:target2:0:6
PM: Removing info for No Bus:target2:0:6
PM: Adding info for No Bus:target2:0:7
PM: Removing info for No Bus:target2:0:7
PM: Adding info for scsi:2:0:0:0
sd 2:0:0:0: [sdc] Attached SCSI removable disk
sd 2:0:0:0: Attached scsi generic sg2 type 0
sd 2:0:0:0: [sdc] 256000 512-byte hardware sectors (131 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 43 00 00 00
sd 2:0:0:0: [sdc] Assuming drive cache: write through
sd 2:0:0:0: [sdc] 256000 512-byte hardware sectors (131 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 43 00 00 00
sd 2:0:0:0: [sdc] Assuming drive cache: write through
sdc: sdc1
Quoted 36 lines · Robert de Rooy
Quoted 3 lines · Alan Stern
Unfortunately you posted the system log file instead of the dmesg log, and your syslogd was configured not to retain debug-level messages.
Ok, I did not realize my syslog was filtering the debug-level messages, here is the output from dmesg
*** plugging device (leaving it in slightly to long, hence the long log); removing the device; rmmod ehci-hcd; plug back in
usb usb4: usb resume
usb usb4: finish resume
hub 4-0:1.0:hub_resumeehci_hcd0000:00:1d.7: resume root hub
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0000ehci_hcd0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status0x501ehci_hcd0000:00:1d.7: port 4 high speedehci_hcd0000:00:1d.7: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT
usb 4-4: new high speed USB device usingehci_hcdand address 2ehci_hcd0000:00:1d.7: devpath 4 ep0in 3strikesehci_hcd0000:00:1d.7: devpath 4 ep0in 3strikesehci_hcd0000:00:1d.7: devpath 4 ep0in 3strikesehci_hcd0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status0x501ehci_hcd0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC
Quoted 8 lines
CONNECT
hub 4-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 4: total 100ms stable 100ms status0x501ehci_hcd0000:00:1d.7: GetStatus port 4 status 001002 POWER sig=se0 CSC hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010
hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0010ehci_hcd0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
Okay. It's clear that you've got a hardware problem of some sort. Hard to say what it is, but evidently the EHCI controller thinks that the device is repeatedly being unplugged and replugged.
Anyway, this isn't a problem of recognizing that a single device is having problems. In fact the computer has no way of knowing that a single device is involved; all it knows is that _something_ gets plugged into the port and then removed. There's no way to tell if it's the same _something_ from one iteration to the next.
You can manually force the port to run at full speed instead of high speed as follows:
echo '4' >/sys/class/usb_host/usb_host4/companion
The "companion" attribute file contains a list of ports which are permanently set to be handled by the EHCI's companion controller. To return to high-speed operation, use '-4' instead of '4' above. This might or might not solve your problem -- the hardware bug might cause the port to return automatically to high-speed regardless.
Let me know what happens.
Alan Stern
Quoted 9 lines · Alan Stern
Okay. It's clear that you've got a hardware problem of some sort. Hard to say what it is, but evidently the EHCI controller thinks that the device is repeatedly being unplugged and replugged.
Anyway, this isn't a problem of recognizing that a single device is
having problems. In fact the computer has no way of knowing that a
single device is involved; all it knows is that _something_ gets
plugged into the port and then removed. There's no way to tell if it's the same _something_ from one iteration to the next.You can manually force the port to run at full speed instead of high speed as follows:
Quoted 7 lines
echo '4' >/sys/class/usb_host/usb_host4/companion
The "companion" attribute file contains a list of ports which are permanently set to be handled by the EHCI's companion controller. To return to high-speed operation, use '-4' instead of '4' above. This might or might not solve your problem -- the hardware bug might cause the port to return automatically to high-speed regardless.
Let me know what happens.
Alan Stern
Yes that works.
I tried to plug and unplug the device repeatedly and each time it came up in full-speed mode.
Quoted 3 lines · Robert de Rooy
Yes that works.
I tried to plug and unplug the device repeatedly and each time it came up in full-speed mode.
Good! I'm glad that "companion" attribute file has come in handy for someone. :-)
Alan Stern
Quoted 11 lines · Alan Stern
Quoted 3 lines · Robert de Rooy
Yes that works.
I tried to plug and unplug the device repeatedly and each time it came up in full-speed mode.Good! I'm glad that "companion" attribute file has come in handy for someone. :-)
Alan Stern
Any way of passing this as a boot parameter? Because I also encountered this when trying to boot Linux from a USB CD-ROM drive. The BIOS part worked fine, but the moment Linux loaded USB support it failed, due to the same problem. This is also why I asked if this failure mode could be handled automatically.
Quoted 9 lines · Robert de Rooy
Quoted 8 lines · Alan Stern
Quoted 4 lines · Robert de Rooy
Yes that works.
I tried to plug and unplug the device repeatedly and each time it came up in full-speed mode.
Quoted 7 lines
Quoted 5 lines
Good! I'm glad that "companion" attribute file has come in handy for someone. :-)
Alan Stern
Any way of passing this as a boot parameter?
Sorry, no. Or not without difficulty, anyway. The problem is that a boot parameter would have to specify which EHCI controller it applied to (some computers have more than one), which complicates things.
Quoted 5 lines
Because I also encountered
this when trying to boot Linux from a USB CD-ROM drive. The BIOS part worked fine, but the moment Linux loaded USB support it failed, due to the same problem. This is also why I asked if this failure mode could be handled automatically.
If you control the contents of the CD then perhaps you can include the necessary command as part of an initrd script.
Another thought occurred: These problems may well be the result of interference from an SMI BIOS. Check your BIOS settings and see if there's anything which can be disabled, or see if there's a BIOS update available.
This particular failure mode is not amenable to automatic handling, since there is no simple way to distinguish it from a valid usage (someone plugging in a device and then unplugging it).
If somebody is motivated enough, they might add code to detect too many connect-change events occurring on a port in a limited period of time. This would require storing a fair amount of extra information for each port on each USB hub. Then you would still need some sort of interface for the automatic speed reduction. It could be done, but I don't want to work on it.
Alan Stern