Skip to contentSkip to conversation

m68k 53c700 SCSI

PATCH In review Geert Uytterhoeven 2 participants 8 messages Jun 17, 2007 – Jun 19, 2007

Subsystems (3)
SCSI Lasi 53c700 driver for PA-RISC 53C700 and 53C700-66 SCSI driver
lore
Share & tools
lore

Geert Uytterhoeven

author
#0 lore raw

cover m68k 53c700 SCSI

Hi James,

These patches add support for m68k to the 53c700 SCSI core and introduce new drivers for various m68k hardware using this 53c700 SCSI core, to replace the just removed drivers using the old 53c7xx SCSI core.

[1] [PATCH] 53c700 scsi: m68k support for the 53c700 SCSI core
[2] [PATCH] 53c700 scsi: m68k BVME6000 NCR53C710 SCSI
[3] [PATCH] 53c700 scsi: m68k MVME16x NCR53C710 SCSI
[4] [PATCH] 53c700 scsi: Amiga 4000T NCR53c710 SCSI
[5] [PATCH] 53c700 scsi: Amiga Zorro NCR53c710 SCSI

Please apply for 2.6.23. Thx!

Gr{oetje,eeting}s,

Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- [email protected]

In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds

author
#1 lore raw

PATCH 1/5 53c700 scsi: m68k support for the 53c700 SCSI core

From: Kars de Jong <[email protected]>

Add m68k support to the 53c700 SCSI driver

Signed-off-by Geert Uytterhoeven <[email protected]>
---
 drivers/scsi/53c700.c |   20 ++++++++++----------
 drivers/scsi/53c700.h |    5 +++++
 drivers/scsi/Kconfig  |   13 +++++--------
 3 files changed, 20 insertions(+), 18 deletions(-)
drivers/scsi/53c700.c +10 -10
@@ -653,7 +653,6 @@ NCR_700_chip_setup(struct Scsi_Host *hos
 {
 	struct NCR_700_Host_Parameters *hostdata = 
 		(struct NCR_700_Host_Parameters *)host->hostdata[0];
-	__u32 dcntl_extra = 0;
 	__u8 min_period;
 	__u8 min_xferp = (hostdata->chip710 ? NCR_710_MIN_XFERP : NCR_700_MIN_XFERP);
 

@@ -678,13 +677,14 @@ NCR_700_chip_setup(struct Scsi_Host *hos
 			        burst_disable = BURST_DISABLE;
 			        break;
 		}
-		dcntl_extra = COMPAT_700_MODE;
+		hostdata->dcntl_extra |= COMPAT_700_MODE;
 
-		NCR_700_writeb(dcntl_extra, host, DCNTL_REG);
+		NCR_700_writeb(hostdata->dcntl_extra, host, DCNTL_REG);
 		NCR_700_writeb(burst_length | hostdata->dmode_extra,
 			       host, DMODE_710_REG);
-		NCR_700_writeb(burst_disable | (hostdata->differential ? 
-						DIFF : 0), host, CTEST7_REG);
+		NCR_700_writeb(burst_disable | hostdata->ctest7_extra |
+			       (hostdata->differential ? DIFF : 0),
+			       host, CTEST7_REG);
 		NCR_700_writeb(BTB_TIMER_DISABLE, host, CTEST0_REG);
 		NCR_700_writeb(FULL_ARBITRATION | ENABLE_PARITY | PARITY
 			       | AUTO_ATN, host, SCNTL0_REG);

@@ -719,13 +719,13 @@ NCR_700_chip_setup(struct Scsi_Host *hos
 		 * of spec: sync divider 2, async divider 3 */
 		DEBUG(("53c700: sync 2 async 3\n"));
 		NCR_700_writeb(SYNC_DIV_2_0, host, SBCL_REG);
-		NCR_700_writeb(ASYNC_DIV_3_0 | dcntl_extra, host, DCNTL_REG);
+		NCR_700_writeb(ASYNC_DIV_3_0 | hostdata->dcntl_extra, host, DCNTL_REG);
 		hostdata->sync_clock = hostdata->clock/2;
 	} else	if(hostdata->clock > 50  && hostdata->clock <= 75) {
 		/* sync divider 1.5, async divider 3 */
 		DEBUG(("53c700: sync 1.5 async 3\n"));
 		NCR_700_writeb(SYNC_DIV_1_5, host, SBCL_REG);
-		NCR_700_writeb(ASYNC_DIV_3_0 | dcntl_extra, host, DCNTL_REG);
+		NCR_700_writeb(ASYNC_DIV_3_0 | hostdata->dcntl_extra, host, DCNTL_REG);
 		hostdata->sync_clock = hostdata->clock*2;
 		hostdata->sync_clock /= 3;
 		

@@ -733,18 +733,18 @@ NCR_700_chip_setup(struct Scsi_Host *hos
 		/* sync divider 1, async divider 2 */
 		DEBUG(("53c700: sync 1 async 2\n"));
 		NCR_700_writeb(SYNC_DIV_1_0, host, SBCL_REG);
-		NCR_700_writeb(ASYNC_DIV_2_0 | dcntl_extra, host, DCNTL_REG);
+		NCR_700_writeb(ASYNC_DIV_2_0 | hostdata->dcntl_extra, host, DCNTL_REG);
 		hostdata->sync_clock = hostdata->clock;
 	} else if(hostdata->clock > 25 && hostdata->clock <=37) {
 		/* sync divider 1, async divider 1.5 */
 		DEBUG(("53c700: sync 1 async 1.5\n"));
 		NCR_700_writeb(SYNC_DIV_1_0, host, SBCL_REG);
-		NCR_700_writeb(ASYNC_DIV_1_5 | dcntl_extra, host, DCNTL_REG);
+		NCR_700_writeb(ASYNC_DIV_1_5 | hostdata->dcntl_extra, host, DCNTL_REG);
 		hostdata->sync_clock = hostdata->clock;
 	} else {
 		DEBUG(("53c700: sync 1 async 1\n"));
 		NCR_700_writeb(SYNC_DIV_1_0, host, SBCL_REG);
-		NCR_700_writeb(ASYNC_DIV_1_0 | dcntl_extra, host, DCNTL_REG);
+		NCR_700_writeb(ASYNC_DIV_1_0 | hostdata->dcntl_extra, host, DCNTL_REG);
 		/* sync divider 1, async divider 1 */
 		hostdata->sync_clock = hostdata->clock;
 	}
drivers/scsi/53c700.h +5 -0
@@ -177,6 +177,7 @@ struct NCR_700_command_slot {
 	__u8	state;
 	#define NCR_700_FLAG_AUTOSENSE	0x01
 	__u8	flags;
+	__u8	pad1[2];	/* Needed for m68k where min alignment is 2 bytes */
 	int	tag;
 	__u32	resume_offset;
 	struct scsi_cmnd *cmnd;

@@ -196,6 +197,8 @@ struct NCR_700_Host_Parameters {
 	void __iomem	*base;		/* the base for the port (copied to host) */
 	struct device	*dev;
 	__u32	dmode_extra;	/* adjustable bus settings */
+	__u32	dcntl_extra;	/* adjustable bus settings */
+	__u32	ctest7_extra;	/* adjustable bus settings */
 	__u32	differential:1;	/* if we are differential */
 #ifdef CONFIG_53C700_LE_ON_BE
 	/* This option is for HP only.  Set it if your chip is wired for

@@ -352,6 +355,7 @@ struct NCR_700_Host_Parameters {
 #define		SEL_TIMEOUT_DISABLE	0x10 /* 710 only */
 #define         DFP                     0x08
 #define         EVP                     0x04
+#define         CTEST7_TT1              0x02
 #define		DIFF			0x01
 #define CTEST6_REG                      0x1A
 #define	TEMP_REG			0x1C

@@ -385,6 +389,7 @@ struct NCR_700_Host_Parameters {
 #define		SOFTWARE_RESET		0x01
 #define		COMPAT_700_MODE		0x01
 #define 	SCRPTS_16BITS		0x20
+#define		EA_710			0x20
 #define		ASYNC_DIV_2_0		0x00
 #define		ASYNC_DIV_1_5		0x40
 #define		ASYNC_DIV_1_0		0x80
drivers/scsi/Kconfig +5 -8
@@ -1006,6 +1006,11 @@ config SCSI_STEX
 	  To compile this driver as a module, choose M here: the
 	  module will be called stex.
 
+config 53C700_BE_BUS
+	bool
+	depends on M68K
+	default y
+
 config SCSI_SYM53C8XX_2
 	tristate "SYM53C8XX Version 2 SCSI support"
 	depends on PCI && SCSI

@@ -1728,14 +1733,6 @@ config BVME6000_SCSI
 	  SCSI controller chip.  Almost everyone using one of these boards
 	  will want to say Y to this question.
 
-config SCSI_NCR53C7xx_FAST
-	bool "allow FAST-SCSI [10MHz]"
-	depends on SCSI_AMIGA7XX || MVME16x_SCSI || BVME6000_SCSI
-	help
-	  This will enable 10MHz FAST-SCSI transfers with your host
-	  adapter. Some systems have problems with that speed, so it's safest
-	  to say N here.
-
 config SUN3_SCSI
 	tristate "Sun3 NCR5380 SCSI"
 	depends on SUN3 && SCSI
Signature · 10 lines
Gr{oetje,eeting}s,

						Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- [email protected]

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
							    -- Linus Torvalds
author
#2 lore raw

PATCH 2/5 53c700 scsi: m68k BVME6000 NCR53C710 SCSI

In reply to Geert Uytterhoeven

From: Kars de Jong <[email protected]>

New driver for the BVME6000 NCR53C710 SCSI controller, using the 53c700 SCSI core.

Signed-off-by Geert Uytterhoeven <[email protected]>
---
 drivers/scsi/Kconfig         |    6 -
 drivers/scsi/Makefile        |    1 
 drivers/scsi/bvme6000_scsi.c |  135 +++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 139 insertions(+), 3 deletions(-)
drivers/scsi/Kconfig +3 -3
@@ -1008,7 +1008,7 @@ config SCSI_STEX
 
 config 53C700_BE_BUS
 	bool
-	depends on M68K
+	depends on BVME6000_SCSI
 	default y
 
 config SCSI_SYM53C8XX_2

@@ -1725,8 +1725,8 @@ config MVME16x_SCSI
 	  will want to say Y to this question.
 
 config BVME6000_SCSI
-	bool "NCR53C710 SCSI driver for BVME6000"
-	depends on BVME6000 && SCSI && BROKEN
+	tristate "NCR53C710 SCSI driver for BVME6000"
+	depends on BVME6000 && SCSI
 	select SCSI_SPI_ATTRS
 	help
 	  The BVME4000 and BVME6000 boards from BVM Ltd use the NCR53C710
drivers/scsi/Makefile +1 -0
@@ -52,6 +52,7 @@ obj-$(CONFIG_ATARI_SCSI)	+= atari_scsi.o
 obj-$(CONFIG_MAC_SCSI)		+= mac_scsi.o
 obj-$(CONFIG_SCSI_MAC_ESP)	+= mac_esp.o	NCR53C9x.o
 obj-$(CONFIG_SUN3_SCSI)		+= sun3_scsi.o  sun3_scsi_vme.o
+obj-$(CONFIG_BVME6000_SCSI)	+= 53c700.o	bvme6000_scsi.o
 obj-$(CONFIG_SCSI_SIM710)	+= 53c700.o	sim710.o
 obj-$(CONFIG_SCSI_ADVANSYS)	+= advansys.o
 obj-$(CONFIG_SCSI_PSI240I)	+= psi240i.o
drivers/scsi/bvme6000_scsi.c new file +135 -0

135 lines not on this page · raw message

Signature · 10 lines
Gr{oetje,eeting}s,

						Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- [email protected]

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
							    -- Linus Torvalds
author
#3 lore raw

PATCH 3/5 53c700 scsi: m68k MVME16x NCR53C710 SCSI

In reply to Geert Uytterhoeven

From: Kars de Jong <[email protected]>

New driver for the MVME16x NCR53C710 SCSI controller, using the 53c700 SCSI core.

Signed-off-by Geert Uytterhoeven <[email protected]>
---
 drivers/scsi/Kconfig        |    6 -
 drivers/scsi/Makefile       |    1 
 drivers/scsi/mvme16x_scsi.c |  158 ++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 162 insertions(+), 3 deletions(-)
drivers/scsi/Kconfig +3 -3
@@ -1008,7 +1008,7 @@ config SCSI_STEX
 
 config 53C700_BE_BUS
 	bool
-	depends on BVME6000_SCSI
+	depends on MVME16x_SCSI || BVME6000_SCSI
 	default y
 
 config SCSI_SYM53C8XX_2

@@ -1716,8 +1716,8 @@ config MVME147_SCSI
 	  single-board computer.
 
 config MVME16x_SCSI
-	bool "NCR53C710 SCSI driver for MVME16x"
-	depends on MVME16x && SCSI && BROKEN
+	tristate "NCR53C710 SCSI driver for MVME16x"
+	depends on MVME16x && SCSI
 	select SCSI_SPI_ATTRS
 	help
 	  The Motorola MVME162, 166, 167, 172 and 177 boards use the NCR53C710
drivers/scsi/Makefile +1 -0
@@ -52,6 +52,7 @@ obj-$(CONFIG_ATARI_SCSI)	+= atari_scsi.o
 obj-$(CONFIG_MAC_SCSI)		+= mac_scsi.o
 obj-$(CONFIG_SCSI_MAC_ESP)	+= mac_esp.o	NCR53C9x.o
 obj-$(CONFIG_SUN3_SCSI)		+= sun3_scsi.o  sun3_scsi_vme.o
+obj-$(CONFIG_MVME16x_SCSI)	+= 53c700.o	mvme16x_scsi.o
 obj-$(CONFIG_BVME6000_SCSI)	+= 53c700.o	bvme6000_scsi.o
 obj-$(CONFIG_SCSI_SIM710)	+= 53c700.o	sim710.o
 obj-$(CONFIG_SCSI_ADVANSYS)	+= advansys.o
drivers/scsi/mvme16x_scsi.c new file +158 -0

158 lines not on this page · raw message

Signature · 10 lines
Gr{oetje,eeting}s,

						Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- [email protected]

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
							    -- Linus Torvalds
author
#4 lore raw

PATCH 4/5 53c700 scsi: Amiga 4000T NCR53c710 SCSI

In reply to Geert Uytterhoeven

From: Kars de Jong <[email protected]>

New driver for the Amiga 4000T built-in NCR53c710 SCSI controller, using the 53c700 SCSI core.

Signed-off-by Geert Uytterhoeven <[email protected]>
---
 drivers/scsi/Kconfig  |   14 ++++
 drivers/scsi/Makefile |    1 
 drivers/scsi/a4000t.c |  142 ++++++++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 155 insertions(+), 2 deletions(-)
drivers/scsi/Kconfig +12 -2
@@ -1008,7 +1008,7 @@ config SCSI_STEX
 
 config 53C700_BE_BUS
 	bool
-	depends on MVME16x_SCSI || BVME6000_SCSI
+	depends on SCSI_A4000T || MVME16x_SCSI || BVME6000_SCSI
 	default y
 
 config SCSI_SYM53C8XX_2

@@ -1615,13 +1615,23 @@ config FASTLANE_SCSI
 	  If you have the Phase5 Fastlane Z3 SCSI controller, or plan to use
 	  one in the near future, say Y to this question. Otherwise, say N.
 
+config SCSI_A4000T
+	tristate "A4000T NCR53c710 SCSI support (EXPERIMENTAL)"
+	depends on AMIGA && SCSI && EXPERIMENTAL
+	select SCSI_SPI_ATTRS
+	help
+	  If you have an Amiga 4000T and have SCSI devices connected to the
+	  built-in SCSI controller, say Y. Otherwise, say N.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called a4000t.
+
 config SCSI_AMIGA7XX
 	bool "Amiga NCR53c710 SCSI support (EXPERIMENTAL)"
 	depends on AMIGA && SCSI && EXPERIMENTAL && BROKEN
 	help
 	  Support for various NCR53c710-based SCSI controllers on the Amiga.
 	  This includes:
-	    - the builtin SCSI controller on the Amiga 4000T,
 	    - the Amiga 4091 Zorro III SCSI-2 controller,
 	    - the MacroSystem Development's WarpEngine Amiga SCSI-2 controller
 	      (info at
drivers/scsi/Makefile +1 -0
@@ -37,6 +37,7 @@ obj-$(CONFIG_SCSI_SAS_LIBSAS)	+= libsas/
 
 obj-$(CONFIG_ISCSI_TCP) 	+= libiscsi.o	iscsi_tcp.o
 obj-$(CONFIG_INFINIBAND_ISER) 	+= libiscsi.o
+obj-$(CONFIG_SCSI_A4000T)	+= 53c700.o	a4000t.o
 obj-$(CONFIG_A3000_SCSI)	+= a3000.o	wd33c93.o
 obj-$(CONFIG_A2091_SCSI)	+= a2091.o	wd33c93.o
 obj-$(CONFIG_GVP11_SCSI)	+= gvp11.o	wd33c93.o
drivers/scsi/a4000t.c new file +142 -0

142 lines not on this page · raw message

Signature · 10 lines
Gr{oetje,eeting}s,

						Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- [email protected]

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
							    -- Linus Torvalds
author
#5 lore raw

PATCH 5/5 53c700 scsi: Amiga Zorro NCR53c710 SCSI

In reply to Geert Uytterhoeven

From: Kars de Jong <[email protected]>

New driver for Amiga Zorro bus NCR53c710 SCSI controllers, using the 53c700 SCSI core.

Signed-off-by Geert Uytterhoeven <[email protected]>
---
 drivers/scsi/Kconfig    |   16 +---
 drivers/scsi/Makefile   |    1 
 drivers/scsi/zorro7xx.c |  181 ++++++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 189 insertions(+), 9 deletions(-)
drivers/scsi/Kconfig +7 -9
@@ -1008,7 +1008,7 @@ config SCSI_STEX
 
 config 53C700_BE_BUS
 	bool
-	depends on SCSI_A4000T || MVME16x_SCSI || BVME6000_SCSI
+	depends on SCSI_A4000T || SCSI_ZORRO7XX || MVME16x_SCSI || BVME6000_SCSI
 	default y
 
 config SCSI_SYM53C8XX_2

@@ -1626,11 +1626,13 @@ config SCSI_A4000T
 	  To compile this driver as a module, choose M here: the
 	  module will be called a4000t.
 
-config SCSI_AMIGA7XX
-	bool "Amiga NCR53c710 SCSI support (EXPERIMENTAL)"
-	depends on AMIGA && SCSI && EXPERIMENTAL && BROKEN
+config SCSI_ZORRO7XX
+	tristate "Zorro NCR53c710 SCSI support (EXPERIMENTAL)"
+	depends on ZORRO && SCSI && EXPERIMENTAL
+	select SCSI_SPI_ATTRS
 	help
-	  Support for various NCR53c710-based SCSI controllers on the Amiga.
+	  Support for various NCR53c710-based SCSI controllers on Zorro
+	  expansion boards for the Amiga.
 	  This includes:
 	    - the Amiga 4091 Zorro III SCSI-2 controller,
 	    - the MacroSystem Development's WarpEngine Amiga SCSI-2 controller

@@ -1639,10 +1641,6 @@ config SCSI_AMIGA7XX
 	    - the SCSI controller on the Phase5 Blizzard PowerUP 603e+
 	      accelerator card for the Amiga 1200,
 	    - the SCSI controller on the GVP Turbo 040/060 accelerator.
-	  Note that all of the above SCSI controllers, except for the builtin
-	  SCSI controller on the Amiga 4000T, reside on the Zorro expansion
-	  bus, so you also have to enable Zorro bus support if you want to use
-	  them.
 
 config OKTAGON_SCSI
 	tristate "BSC Oktagon SCSI support (EXPERIMENTAL)"
drivers/scsi/Makefile +1 -0
@@ -38,6 +38,7 @@ obj-$(CONFIG_SCSI_SAS_LIBSAS)	+= libsas/
 obj-$(CONFIG_ISCSI_TCP) 	+= libiscsi.o	iscsi_tcp.o
 obj-$(CONFIG_INFINIBAND_ISER) 	+= libiscsi.o
 obj-$(CONFIG_SCSI_A4000T)	+= 53c700.o	a4000t.o
+obj-$(CONFIG_SCSI_ZORRO7XX)	+= 53c700.o	zorro7xx.o
 obj-$(CONFIG_A3000_SCSI)	+= a3000.o	wd33c93.o
 obj-$(CONFIG_A2091_SCSI)	+= a2091.o	wd33c93.o
 obj-$(CONFIG_GVP11_SCSI)	+= gvp11.o	wd33c93.o
drivers/scsi/zorro7xx.c new file +181 -0

181 lines not on this page · raw message

Signature · 10 lines
Gr{oetje,eeting}s,

						Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- [email protected]

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
							    -- Linus Torvalds
author
#6 lore raw
In reply to Geert Uytterhoeven

Hi James,

Quoted 11 lines · Geert Uytterhoeven

These patches add support for m68k to the 53c700 SCSI core and introduce new drivers for various m68k hardware using this 53c700 SCSI core, to replace the just removed drivers using the old 53c7xx SCSI core.

[1] [PATCH] 53c700 scsi: m68k support for the 53c700 SCSI core
[2] [PATCH] 53c700 scsi: m68k BVME6000 NCR53C710 SCSI
[3] [PATCH] 53c700 scsi: m68k MVME16x NCR53C710 SCSI
[4] [PATCH] 53c700 scsi: Amiga 4000T NCR53c710 SCSI
[5] [PATCH] 53c700 scsi: Amiga Zorro NCR53c710 SCSI

Please apply for 2.6.23. Thx!

Apparently I made some major mistakes when preparing these patches. Here are the fixes.
---

Fixup m68k 53c700 drivers:
- a4000t.c: Add missing include, needed in some configurations
- bvme6000_scsi.c: Kill bogus opening brace
- zorro7xx.c: Remove MODULE_DEVICE_TABLE, it should be part of another patch

Signed-off-by Geert Uytterhoeven <[email protected]>
---
 drivers/scsi/a4000t.c        |    1 +
 drivers/scsi/bvme6000_scsi.c |    2 +-
 drivers/scsi/zorro7xx.c      |    1 -
 3 files changed, 2 insertions(+), 2 deletions(-)
drivers/scsi/a4000t.c +1 -0
@@ -12,6 +12,7 @@
 #include <linux/platform_device.h>
 #include <linux/init.h>
 #include <linux/interrupt.h>
+#include <asm/amigahw.h>
 #include <asm/amigaints.h>
 #include <scsi/scsi_host.h>
 #include <scsi/scsi_transport_spi.h>
drivers/scsi/bvme6000_scsi.c +1 -1
@@ -112,7 +112,7 @@ static int __init bvme6000_scsi_init(voi
 	int err;
 
 	err = driver_register(&bvme6000_scsi_driver);
-	if (err) {
+	if (err)
 		return err;
 
 	bvme6000_scsi_device = platform_device_register_simple("bvme6000-scsi",
drivers/scsi/zorro7xx.c +0 -1
@@ -65,7 +65,6 @@ static struct zorro_device_id zorro7xx_z
 	},
 	{ 0 }
 };
-MODULE_DEVICE_TABLE(zorro, zorro7xx_zorro_tbl);
 
 static int __devinit zorro7xx_init_one(struct zorro_dev *z,
 				       const struct zorro_device_id *ent)

Gr{oetje,eeting}s,

Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- [email protected]

In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds

#7 lore raw
In reply to Geert Uytterhoeven
Quoted 6 lines · Geert Uytterhoeven

Hi James,

These patches add support for m68k to the 53c700 SCSI core and introduce new drivers for various m68k hardware using this 53c700 SCSI core, to replace the just removed drivers using the old 53c7xx SCSI core.

Quoted 7 lines

[1] [PATCH] 53c700 scsi: m68k support for the 53c700 SCSI core
[2] [PATCH] 53c700 scsi: m68k BVME6000 NCR53C710 SCSI
[3] [PATCH] 53c700 scsi: m68k MVME16x NCR53C710 SCSI
[4] [PATCH] 53c700 scsi: Amiga 4000T NCR53c710 SCSI
[5] [PATCH] 53c700 scsi: Amiga Zorro NCR53c710 SCSI

Please apply for 2.6.23. Thx!

The patches all look very nice to me, thanks a lot.