DRI/AGP on AMD64 based machine
Hi,
For a while now I've been meaning to get DRI running with my rv350 graphics card on my AMD64 machine. However I don't seem to be able to get the right config-fu in the kernel to enable all the components.
For my sins I've been following the Gentoo Howto Wiki
(http://gentoo-wiki.com/HOWTO_DRI_with_ATi_Open-Source_Drivers)
A lot of the AGP stuff in the Kernel seems to be locked to 32 bit kernels. The instructions seem to imply there is an am64-agp module (which looks as though it builds in the tree but doesn't install) and possibly an nvidea-agp module. I'm a little confused as I have both AMD and NVidia chipsets on my machine:
malory agp # lspci
00:00.0 Host bridge: nVidia Corporation nForce3 250Gb Host Bridge (rev a1)
00:01.0 ISA bridge: nVidia Corporation nForce3 250Gb LPC Bridge (rev a2) 00:01.1 SMBus: nVidia Corporation nForce 250Gb PCI System Management (rev a1)
00:02.0 USB Controller: nVidia Corporation CK8S USB Controller (rev a1) 00:02.1 USB Controller: nVidia Corporation CK8S USB Controller (rev a1) 00:02.2 USB Controller: nVidia Corporation nForce3 EHCI USB 2.0 Controller (rev a2)
00:05.0 Bridge: nVidia Corporation CK8S Ethernet Controller (rev a2) 00:06.0 Multimedia audio controller: nVidia Corporation nForce3 250Gb AC'97 Audio Controller (rev a1)
00:08.0 IDE interface: nVidia Corporation CK8S Parallel ATA Controller (v2.5) (rev a2)
00:0a.0 IDE interface: nVidia Corporation CK8S Serial ATA Controller (v2.5) (rev a2)
00:0b.0 PCI bridge: nVidia Corporation nForce3 250Gb AGP Host to PCI Bridge (rev a2)
00:0e.0 PCI bridge: nVidia Corporation nForce3 250Gb PCI-to-PCI Bridge (rev a2)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:00.0 VGA compatible controller: ATI Technologies Inc RV350 AS [Radeon 9550]
01:00.1 Display controller: ATI Technologies Inc RV350 AS [Radeon 9550] (Secondary)
02:06.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 80)
02:0a.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
Any clues on the correct AGP config options to switch on gratefully received. My current .config looks like:
08:56 alex@malory [linux-2.6-stable.git] >grep "AGP" .config CONFIG_AGP=yCONFIG_AGP_AMD64=yCONFIG_AGP_INTEL=m
# CONFIG_AGP_SIS is not setCONFIG_AGP_VIA=m
08:59 alex@malory [linux-2.6-stable.git] >grep "DRM" .config CONFIG_DRM=m
# CONFIG_DRM_TDFX is not set
# CONFIG_DRM_R128 is not setCONFIG_DRM_RADEON=m
# CONFIG_DRM_I810 is not set
# CONFIG_DRM_I830 is not set
# CONFIG_DRM_I915 is not setCONFIG_DRM_MGA=m
# CONFIG_DRM_SIS is not set
# CONFIG_DRM_VIA is not set
# CONFIG_DRM_SAVAGE is not set
Regards,
--
Alex, homepage: http://www.bennee.com/~alex/
Television has brought back murder into the home -- where it belongs. -- Alfred Hitchcock
Quoted 6 lines · Alex Bennee
Hi,
For a while now I've been meaning to get DRI running with my rv350 graphics card on my AMD64 machine. However I don't seem to be able to get the right config-fu in the kernel to enable all the components.
Quoted 8 lines
For my sins I've been following the Gentoo Howto Wiki
(http://gentoo-wiki.com/HOWTO_DRI_with_ATi_Open-Source_Drivers)A lot of the AGP stuff in the Kernel seems to be locked to 32 bit kernels. The instructions seem to imply there is an am64-agp module (which looks as though it builds in the tree but doesn't install) and possibly an nvidea-agp module. I'm a little confused as I have both AMD and NVidia chipsets on my machine:
For the sake of AGP, we only use the on-CPU GART.
The (nvidia) chipset one is ignored.
If amd64-agp isn't working for you, attach your dmesg. (You can also confirm its working by running testgart[1])
Dave
[1] http://www.codemonkey.org.uk/projects/agp/testgart.c
Signature · 1 line
http://www.codemonkey.org.uk
Quoted 5 lines · Dave Jones
For the sake of AGP, we only use the on-CPU GART.
The (nvidia) chipset one is ignored.If amd64-agp isn't working for you, attach your dmesg. (You can also confirm its working by running testgart[1])
Hi Dave, I have an amd64 box for which every kernel after 2.6.18 hangs during boot, so I have no dmesg :(
I used git bisect to find out where the problem patch is, and assuming bisect works (imho it jumped between versions very weirdly: closing in on the last 6 revisions, it jumped from 2.6.18 to 2.6.18-rc2 to 2.6.18-rc6), the problem is a patch in intel-agp.c, where support for the intel 965G is added (which I have).
I mailed the author of the patch, including the git Id of that patch... but he didn't reply... and I didn't keep the mail :/ So, I am afraid I can't give much details.
I'd still like to have it sorted out. If you give me the green light (in the sense that you are willing to help a kernel-newbie when needed) then I'll have another attempt at getting more information.
Signature · 3 lines
Carlo Wood <[email protected]> PS I believe it was you who committed the patch.
Quoted 10 lines · Carlo Wood
Quoted 5 lines · Dave Jones
For the sake of AGP, we only use the on-CPU GART.
The (nvidia) chipset one is ignored.If amd64-agp isn't working for you, attach your dmesg. (You can also confirm its working by running testgart[1])
Hi Dave, I have an amd64 box for which every kernel after 2.6.18 hangs during boot, so I have no dmesg :(
Quoted 6 lines
I used git bisect to find out where the problem patch is, and assuming bisect works (imho it jumped between versions very weirdly: closing in on the last 6 revisions, it jumped from 2.6.18 to 2.6.18-rc2 to 2.6.18-rc6), the problem is a patch in
intel-agp.c, where support for the intel 965G is added (which I have).
How do you have a 965G in an amd64 box? does not compute.
Dave.
Quoted 1 line · Dave Airlie
How do you have a 965G in an amd64 box? does not compute.
Why not? It's the ASUS P5B Deluxe motherboard with an Intel P965/ICH8R chipset. The cpu is a QX6700 2.66 GHz, that's an Intel Core 2 Quad Extreme.
amd64 is just the architecture, not the brand. It's an all intel machine, if that's what you mean.
Signature · 1 line
Carlo Wood <[email protected]>
Quoted 10 lines · Carlo Wood
Quoted 1 line · Dave Airlie
How do you have a 965G in an amd64 box? does not compute.
Why not? It's the ASUS P5B Deluxe motherboard with an Intel P965/ICH8R chipset. The cpu is a QX6700 2.66 GHz, that's an Intel Core 2 Quad Extreme.
amd64 is just the architecture, not the brand. It's an all intel machine, if that's what you mean.
x86-64 is an architecture, amd64 is used by some people however in your case agp-amd64 is not what you wanted, you have a problem with intel-agp.c then.. which is different than what started this thread..
Dave.
[AGPGART] intel_agp: use table for device probe
In reply to Carlo WoodQuoted 10 lines · Carlo Wood
Hi Dave, I have an amd64 box for which every kernel after 2.6.18 hangs during boot, so I have no dmesg :(
I used git bisect to find out where the problem patch is, and assuming bisect works (imho it jumped between versions very weirdly: closing in on the last 6 revisions, it jumped from 2.6.18 to 2.6.18-rc2 to 2.6.18-rc6), the problem is a patch in
intel-agp.c, where support for the intel 965G is added (which I have).
Quoted 8 lines
I mailed the author of the patch, including the git Id of that patch... but he didn't reply... and I didn't keep the mail :/ So, I am afraid I can't give much details.
I'd still like to have it sorted out. If you give me the green light (in the sense that you are willing to help a kernel-newbie when needed) then I'll have another attempt at getting more information.
Dave, I have no idea why you never replied to this -- don't you care that kernels 2.6.19 through 2.6.21 lockup on boot? -- here is a follow up on this matter.
I am not sure which patch it was exactly that broke things, but I think it was:
[AGPGART] Intel 965 Express support.
From: Alan Hourihane <[email protected]>
From: Eric Anholt <[email protected]>
65c25aadfa4e917060e99fe459f33a6a07db53cc
which was supplied after 2.6.18 and before 2.6.19-rc1.
If I remember that correctly, then Alan should have a mail from me with the exact git Id (he never replied either).
The patch causes my machine to lock up and/or crash
in various ways (depending on the exact version of the kernel), very shortly after printing: agpgart: Detected an Intel 965G Chipset.
The first kernel version that stops doing that is 2.6.22-rc5. I used git bisect once more to find the patch that fixes this bug:
commit 9614ece14f23f2ce54a076c471aec9c91e51e79c
Author: Wang Zhenyu <[email protected]> Date: Wed May 30 09:45:58 2007 +0800
[AGPGART] intel_agp: use table for device probe
Fixed issues noted by Christoph Hellwig, and I changed device table scan a bit to allow the case that some models of graphics chips may have same host bridge type. This type of chip will be added in the future.
This patch cleans up device probe function. Eric Anholt was the original aut hor.
:040000 040000 625da154215c98f9016e14b952131a0c1ec8597b cddcf0b42d3632d20d7ee863 91d6ae6d258632e2 M drivers
I am mailing this mostly because the comment doesn't seem to indicate that the author is aware that this patch fixes an existing regression (it worked fine for me with 2.6.18).
Anyway, thanks for fixing this Wang Zhenyu.
If anyone wants to know more (like what hardware I'm using), please show me that you're actually alive / reading my mails.
Signature · 1 line
Carlo Wood <[email protected]>
Re: [AGPGART] intel_agp: use table for device probe
Quoted 11 lines · Carlo Wood
Quoted 9 lines
Hi Dave, I have an amd64 box for which every kernel after 2.6.18 hangs during boot, so I have no dmesg :(
I used git bisect to find out where the problem patch is, and assuming bisect works (imho it jumped between versions very weirdly: closing in on the last 6 revisions, it jumped from 2.6.18 to 2.6.18-rc2 to 2.6.18-rc6), the problem is a patch in
intel-agp.c, where support for the intel 965G is added (which I have).Dave, I have no idea why you never replied to this -- don't you care that kernels 2.6.19 through 2.6.21 lockup on boot? --
Sometimes things fall through the cracks..
I haven't heard any similar problems, which makes it somewhat odd.
Quoted 9 lines
The patch causes my machine to lock up and/or crash
in various ways (depending on the exact version of the kernel), very shortly after printing: agpgart: Detected an Intel 965G Chipset.The first kernel version that stops doing that is 2.6.22-rc5. I used git bisect once more to find the patch that fixes this bug:
I am mailing this mostly because the comment doesn't seem to indicate that the author is aware that this patch fixes an existing regression (it worked fine for me with 2.6.18).
Indeed, it was unknown to me too, this should have just been a clean-up.
Quoted 2 lines
If anyone wants to know more (like what hardware I'm using), please show me that you're actually alive / reading my mails.
Out of curiousity, I'd like to see your lspci
(not -v or anything, just run with no args)
Dave
Signature · 1 line
http://www.codemonkey.org.uk
Re: [AGPGART] intel_agp: use table for device probe
Quoted 2 lines · Dave Jones
Sometimes things fall through the cracks..
I haven't heard any similar problems, which makes it somewhat odd.
Ok. Well, the lockup is all to real here :p
I suspect a memory corruption going on, as under certain circumstances there is printed more after the "agpgart: Detected an Intel 965G Chipset." -- that is, the kernel *sometimes* doesn't hang silently, but either reboots by itself (hard reset) or prints something that looks like a total crash to me. Often, this is prefixed by the name of running process. I am sorry, I never wrote any of that down. Only the last time, it then went like:
agpgart: Detected an Intel 965G Chipset.
modprobe: Corrupt page table at address 20
PGD 178c6c067 PUD 201000c0049c04f BAD
This very same kernel (I boot it several times to see how reproducable things were) always prints "agpgart: Detected an Intel 965G Chipset." but then either hangs (two times), prints the above and hangs (one time) or hard resets (one time).
Then I also booted the other kernels several times, and kernels that booted fine ALWAYS boot fine - while kernels that locked up (that I tested by booting them three times) only printed the agpgart line and locked up three times.
Quoted 4 lines
Quoted 4 lines
The patch causes my machine to lock up and/or crash
in various ways (depending on the exact version of the kernel), very shortly after printing: agpgart: Detected an Intel 965G Chipset.
Quoted 8 lines
Quoted 5 lines
The first kernel version that stops doing that is 2.6.22-rc5. I used git bisect once more to find the patch that fixes this bug:
I am mailing this mostly because the comment doesn't seem to indicate that the author is aware that this patch fixes an existing regression (it worked fine for me with 2.6.18).Indeed, it was unknown to me too, this should have just been a clean-up.
I hope you saw my later post too? I sent it to you too - but also to the list, so I don't know if you'll notice it.
The Subject of that post is: 2.6.22-rc5 regression
I concluded too soon that 2.6.22-rc5 was working :(. I just really tested it and it doesn't! Same error.
Please have a look at that other post of me and lets continue this thread there.
Quoted 2 lines
Out of curiousity, I'd like to see your lspci
(not -v or anything, just run with no args)
I'll add that to that other thread.
Signature · 1 line
Carlo Wood <[email protected]>
Re: [AGPGART] intel_agp: use table for device probe
Quoted 14 lines · Carlo Wood
Quoted 2 lines · Dave Jones
Sometimes things fall through the cracks..
I haven't heard any similar problems, which makes it somewhat odd.Ok. Well, the lockup is all to real here :p
I suspect a memory corruption going on, as under certain circumstances there is printed more after the "agpgart: Detected an Intel 965G Chipset." -- that is, the kernel *sometimes* doesn't hang silently, but either reboots by itself (hard reset) or prints something that looks like a total crash to me. Often, this is prefixed by the name of running process. I am sorry, I never wrote any of that down. Only the last time, it then went like:
Quoted 3 lines
agpgart: Detected an Intel 965G Chipset.
modprobe: Corrupt page table at address 20
PGD178c6c067PUD201000c0049c04fBAD
That's pretty bad corruption indeed. What I'm puzzling over though is why other 965G users aren't seeing the same thing.
My own 965G seems to be fine, though that's using Intel graphics instead of nvidia.
(Just to rule it out, I'm assuming at this stage in boot that the
nvidia driver module has never been loaded?)
And if you never load the agpgart modules, you never see lockups?
Right now, I'm at a loss to explain this.
Dave
Signature · 1 line
http://www.codemonkey.org.uk
Re: [AGPGART] intel_agp: use table for device probe
Quoted 7 lines · Dave Jones
That's pretty bad corruption indeed. What I'm puzzling over though is why other 965G users aren't seeing the same thing.
My own 965G seems to be fine, though that's using Intel graphics instead of nvidia.(Just to rule it out, I'm assuming at this stage in boot that the
nvidia driver module has never been loaded?)
Doesn't even exist for that kernel. I only compiled a new nvidia driver module for one kernel - the one that I am using on a daily basis.
Quoted 1 line
And if you never load the agpgart modules, you never see lockups?
What would the name be of such module?
In fact, I think that when the kernel does NOT lockup, it doesn't print this "agpgart: Detected.." line either.
Ie, the dmesg of cf68676222e54cd0a31efd968da00e65f9a0963f which boots fine, gives:
$ grep Detected dmesg-cf686 time.c: Detected 2666.669 MHz processor. Detected 16.666 MHz APIC timer.
$ grep agpgart dmesg-cf686 Linux agpgart interface v0.102 (c) Dave Jones
Does that give an indication of what you want me to test/try?
Signature · 1 line
Carlo Wood <[email protected]>
Re: [AGPGART] intel_agp: use table for device probe
Quoted 9 lines · Carlo Wood
Quoted 7 lines · Dave Jones
That's pretty bad corruption indeed. What I'm puzzling over though is why other 965G users aren't seeing the same thing.
My own 965G seems to be fine, though that's using Intel graphics instead of nvidia.(Just to rule it out, I'm assuming at this stage in boot that the
nvidia driver module has never been loaded?)
Quoted 7 lines
Doesn't even exist for that kernel. I only compiled a new nvidia driver module for one kernel - the one that I am using on a daily basis.
Quoted 1 line
And if you never load the agpgart modules, you never see lockups?
What would the name be of such module?
intel-agp
Though by the looks of things, with the working kernel, you don't have it loaded (it's dependant upon the 'agpgart' module, which prints the "Detected" line that was missing).
Dave
Signature · 1 line
http://www.codemonkey.org.uk
Re: [AGPGART] intel_agp: use table for device probe
Quoted 7 lines · Dave Jones
Quoted 1 line
What would the name be of such module?
intel-agp
Though by the looks of things, with the working kernel, you don't have it loaded (it's dependant upon the 'agpgart' module, which prints the "Detected" line that was missing).
hikaru:~>lsmod | grep agpintel_agp 31776 0
It's loaded right now... that is with 2.6.22-rc4-+something (one of the working ones). I don't know WHEN it was loaded though. Probably not at the same time as the others.
And
hikaru:~>dmesg | grep agpgart
Linux agpgart interface v0.102 (c) Dave Jones
No 'Detected' line :/
Also, I noted that this 'agpgart: Detected..' line is always(?) printed right after (often even without THAT line having printed a newline yet!) something like:
udev: Waiting for /dev to be fully populated...agpgart: Detected an Intel 965G Chipset.
And this 'udev: Waiting for /dev to be fully populated' (sorry, didn't write down the exact phrase, this is from memory) is also not printed by kernels that work.
Signature · 4 lines
Carlo Wood <[email protected]> PS I asked you move to the other thread - it's a bit annoying to have two threads about this now.
Re: [AGPGART] intel_agp: use table for device probe
In reply to Dave JonesQuoted 7 lines · Dave Jones
Quoted 1 line
What would the name be of such module?
intel-agp
Though by the looks of things, with the working kernel, you don't have it loaded (it's dependant upon the 'agpgart' module, which prints the "Detected" line that was missing).
I can rmmod intel-agp without problems.
The agpgart module isn't loaded.
Signature · 1 line
Carlo Wood <[email protected]>
Re: [AGPGART] intel_agp: use table for device probe
In reply to Dave JonesQuoted 5 lines · Dave Jones
intel-agp
Though by the looks of things, with the working kernel, you don't have it loaded (it's dependant upon the 'agpgart' module, which prints the "Detected" line that was missing).
You are wrong.
1)
I don't have any agpgart module at all, in any of the kernels that I compiled.
$ find /lib/modules -name 'agpgart.ko' $ /lib/modules/2.6.22-rc5-master-188e1f81ba31af1b65a2f3611df4c670b092bbac-amd64 -name '*agp*.ko' /lib/modules/2.6.22-rc5-master-188e1f81ba31af1b65a2f3611df4c670b092bbac-amd64/kernel/drivers/char/agp/sis-agp.ko /lib/modules/2.6.22-rc5-master-188e1f81ba31af1b65a2f3611df4c670b092bbac-amd64/kernel/drivers/char/agp/intel-agp.ko /lib/modules/2.6.22-rc5-master-188e1f81ba31af1b65a2f3611df4c670b092bbac-amd64/kernel/drivers/char/agp/via-agp.ko
2)
$ strings /lib/modules/2.6.22-rc5-master-188e1f81ba31af1b65a2f3611df4c670b092bbac-amd64/kernel/drivers/char/agp/intel-agp.ko | grep 'agpgart: Detected an Intel' <6>agpgart: Detected an Intel %s Chipset.
Hence, in the case that the kernel works, intel-agp is loaded WITHOUT printing this Detected line - while when it doesn't work, it is loaded while printing this line.
Perhaps my "solution" is to remove this module completely? I don't seem to need it.
Signature · 1 line
Carlo Wood <[email protected]>
Re: [AGPGART] intel_agp: use table for device probe
Quoted 9 lines · Carlo Wood
Quoted 5 lines · Dave Jones
intel-agp
Though by the looks of things, with the working kernel, you don't have it loaded (it's dependant upon the 'agpgart' module, which prints the "Detected" line that was missing).
You are wrong.
I don't have any agpgart module at all, in any of the kernels that I compiled.
ok, then you must have CONFIG_AGP=y
Quoted 6 lines
$ find /lib/modules -name 'agpgart.ko' $ /lib/modules/2.6.22-rc5-master-188e1f81ba31af1b65a2f3611df4c670b092bbac-amd64 -name '*agp*.ko' /lib/modules/2.6.22-rc5-master-188e1f81ba31af1b65a2f3611df4c670b092bbac-amd64/kernel/drivers/char/agp/sis-agp.ko /lib/modules/2.6.22-rc5-master-188e1f81ba31af1b65a2f3611df4c670b092bbac-amd64/kernel/drivers/char/agp/intel-agp.ko /lib/modules/2.6.22-rc5-master-188e1f81ba31af1b65a2f3611df4c670b092bbac-amd64/kernel/drivers/char/agp/via-agp.ko
Quoted 7 lines
2)
$ strings /lib/modules/2.6.22-rc5-master-188e1f81ba31af1b65a2f3611df4c670b092bbac-amd64/kernel/drivers/char/agp/intel-agp.ko | grep 'agpgart: Detected an Intel' <6>agpgart: Detected an Intel %s Chipset.Hence, in the case that the kernel works, intel-agp is loaded WITHOUT printing this Detected line
That doesn't make much sense. The hardware doesn't change between a working & not-working kernel, and somehow the PCI probing fails. Hmm, do you have CONFIG_EDAC set ?
There's an outstanding bug (well, lack of feature) , where it claims the PCI device before AGP gets a chance to.
This is unrelated to your hang however, but would at least explain the inconsistent probing.
Quoted 2 lines
Perhaps my "solution" is to remove this module completely? I don't seem to need it.
It's needed only for 3d, but it'd be good to figure out why its so broken on your system, even if you don't need it.
Dave
Signature · 1 line
http://www.codemonkey.org.uk
Re: [AGPGART] intel_agp: use table for device probe
Quoted 1 line · Dave Jones
ok, then you must have
CONFIG_AGP=y
I do - not voluntary however. For some mysterious reason I am unable to set it to n or m. I am also not able to set CONFIG_AGP_INTEL to n, only to y or m.
(using make 'menuconfig' for example).
Quoted 11 lines
Quoted 11 lines
$ find /lib/modules -name 'agpgart.ko' $ /lib/modules/2.6.22-rc5-master-188e1f81ba31af1b65a2f3611df4c670b092bbac-amd64 -name '*agp*.ko' /lib/modules/2.6.22-rc5-master-188e1f81ba31af1b65a2f3611df4c670b092bbac-amd64/kernel/drivers/char/agp/sis-agp.ko /lib/modules/2.6.22-rc5-master-188e1f81ba31af1b65a2f3611df4c670b092bbac-amd64/kernel/drivers/char/agp/intel-agp.ko /lib/modules/2.6.22-rc5-master-188e1f81ba31af1b65a2f3611df4c670b092bbac-amd64/kernel/drivers/char/agp/via-agp.ko2)
$ strings /lib/modules/2.6.22-rc5-master-188e1f81ba31af1b65a2f3611df4c670b092bbac-amd64/kernel/drivers/char/agp/intel-agp.ko | grep 'agpgart: Detected an Intel' <6>agpgart: Detected an Intel %s Chipset.
Quoted 6 lines
Quoted 2 lines
Hence, in the case that the kernel works, intel-agp is loaded WITHOUT printing this Detected line
That doesn't make much sense. The hardware doesn't change between a working & not-working kernel, and somehow the PCI probing fails. Hmm, do you have
CONFIG_EDACset ?
CONFIG_EDAC=m
$ lsmod | grep edac $
Quoted 9 lines
There's an outstanding bug (well, lack of feature) , where it claims the PCI device before AGP gets a chance to.
This is unrelated to your hang however, but would at least explain the inconsistent probing.Quoted 2 lines
Perhaps my "solution" is to remove this module completely? I don't seem to need it.
It's needed only for 3d,
Nope - I just played UT2004 without problems, and without intel-agp loaded.
Quoted 2 lines
but it'd be good to figure out why its so
broken on your system, even if you don't need it.
Please tell me what to do / try.
I'm an experienced coder - but I never really played with the kernel before - so you'll have to spell out how to turn on debugging etc.
Signature · 1 line
Carlo Wood <[email protected]>
Re: [AGPGART] intel_agp: use table for device probe
Quoted 5 lines · Carlo Wood
Quoted 1 line · Dave Jones
ok, then you must have
CONFIG_AGP=yI do - not voluntary however. For some mysterious reason I am unable to set it to n or m.
You likely have CONFIG_IOMMU set. This makes AGP non-optional.
Quoted 3 lines
I am also not able to set
CONFIG_AGP_INTEL
to n, only to y or m.
(using make 'menuconfig' for example).
Can't explain that one.
Quoted 10 lines
Quoted 6 lines
Quoted 2 lines
Hence, in the case that the kernel works, intel-agp is loaded WITHOUT printing this Detected line
That doesn't make much sense. The hardware doesn't change between a working & not-working kernel, and somehow the PCI probing fails. Hmm, do you have
CONFIG_EDACset ?
CONFIG_EDAC=m$ lsmod | grep edac
ok, red herring.
Quoted 11 lines
Quoted 9 lines
There's an outstanding bug (well, lack of feature) , where it claims the PCI device before AGP gets a chance to.
This is unrelated to your hang however, but would at least explain the inconsistent probing.Quoted 2 lines
Perhaps my "solution" is to remove this module completely? I don't seem to need it.
It's needed only for 3d,
Nope - I just played UT2004 without problems, and without intel-agp loaded.
Using the nvidia driver? It has its own built-in AGP support which will get used if the kernel AGP support is missing.
Quoted 6 lines
Quoted 2 lines
but it'd be good to figure out why its so
broken on your system, even if you don't need it.Please tell me what to do / try.
I'm an experienced coder - but I never really played with the kernel before - so you'll have to spell out how to turn on debugging etc.
Right now, I'm at a loss to explain the corruption, so it's difficult to suggest what to try.
Dave
Signature · 1 line
http://www.codemonkey.org.uk
Re: [AGPGART] intel_agp: use table for device probe
Quoted 3 lines
Right now, I'm at a loss to explain the corruption, so it's difficult to suggest what to try.
The thing is here, this is PCIE, so if there is a GPU plugged into the PCIE 16x slot in theory the main onboard graphics should disable, AGP code is used to control the GART for the onboard chip, in this case a plugged in card will not use AGP, I wonder have Intel tested with a pcie card in place...
Dave.
Re: [AGPGART] intel_agp: use table for device probe
Quoted 8 lines · Dave Airlie
Quoted 2 lines
Right now, I'm at a loss to explain the corruption, so it's difficult to suggest what to try.
The thing is here, this is PCIE, so if there is a GPU plugged into the PCIE 16x slot in theory the main onboard graphics should disable, AGP code is used to control the GART for the onboard chip, in this case a plugged in card will not use AGP, I wonder have Intel tested with a pcie card in place...
That is Chinese for me :/.
Do you want me to try something?
Signature · 1 line
Carlo Wood <[email protected]>
Re: [AGPGART] intel_agp: use table for device probe
Quoted 10 lines
Quoted 6 lines
The thing is here, this is PCIE, so if there is a GPU plugged into the PCIE 16x slot in theory the main onboard graphics should disable, AGP code is used to control the GART for the onboard chip, in this case a plugged in card will not use AGP, I wonder have Intel tested with a pcie card in place...
That is Chinese for me :/.
Do you want me to try something?
Well it was more for davej's benefit, in theory for your machine with a PCIE graphics card you don't need agpgart enabled at all granted it shouldn't screw up if it is..
Dave.
Re: [AGPGART] intel_agp: use table for device probe
Quoted 3 lines · Dave Airlie
Well it was more for davej's benefit, in theory for your machine with a PCIE graphics card you don't need agpgart enabled at all granted it shouldn't screw up if it is..
I can't disable it though.
I am not THAT much interested in disabling it however as long as I get help here to debug this. I am interested in finding out what is causing the crash, can't stand it to have a bug on my machine without knowing what it is ;)
Signature · 1 line
Carlo Wood <[email protected]>
Re: [AGPGART] intel_agp: use table for device probe
In reply to Carlo WoodQuoted 9 lines · Carlo Wood
Quoted 8 lines · Dave Airlie
Quoted 2 lines
Right now, I'm at a loss to explain the corruption, so it's difficult to suggest what to try.
The thing is here, this is PCIE, so if there is a GPU plugged into the PCIE 16x slot in theory the main onboard graphics should disable, AGP code is used to control the GART for the onboard chip, in this case a plugged in card will not use AGP, I wonder have Intel tested with a pcie card in place...
Agree. We seem to always enable AGP even IGD is disabled or not exists, other card should not depend on this module ever.
Quoted 3 lines
That is Chinese for me :/.
Do you want me to try something?
Carlo, I've just built latest kernel git tree on a Dell 965G box and have a NV card plugged-in. It boots fine.
Linux agpgart interface v0.102 (c) Dave Jones
agpgart: Detected an Intel 965G Chipset.
agpgart: AGP aperture is 256M @ 0x0
I don't know why it hangs your machine when loading this module, it should just not bother anything. But from your last "modprobe: ..." line, it seems there's really badness somewhere, do you have serial console to see more in the message?
Re: [AGPGART] intel_agp: use table for device probe
Quoted 19 lines · Wang Zhenyu
Quoted 8 lines · Carlo Wood
Quoted 7 lines · Dave Airlie
Quoted 2 lines
Right now, I'm at a loss to explain the corruption, so it's difficult to suggest what to try.
The thing is here, this is PCIE, so if there is a GPU plugged into the PCIE 16x slot in theory the main onboard graphics should disable, AGP code is used to control the GART for the onboard chip, in this case a plugged in card will not use AGP, I wonder have Intel tested with a pcie card in place...
Agree. We seem to always enable AGP even IGD is disabled or not exists, other card should not depend on this module ever.
Quoted 2 lines
That is Chinese for me :/.
Do you want me to try something?Carlo, I've just built latest kernel git tree on a Dell 965G box and have a NV card plugged-in. It boots fine.
Quoted 8 lines
Linux agpgart interface v0.102 (c) Dave Jones
agpgart: Detected an Intel 965G Chipset.
agpgart: AGP aperture is 256M @0x0I don't know why it hangs your machine when loading this module, it should just not bother anything. But from your last "modprobe: ..." line, it seems there's really badness somewhere, do you have serial console to see more in the message?
There are also these bug reports:
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=229913
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=242101
Re: [AGPGART] intel_agp: use table for device probe
Quoted 29 lines · Chuck Ebbert
Quoted 19 lines · Wang Zhenyu
Quoted 8 lines · Carlo Wood
Quoted 7 lines · Dave Airlie
Quoted 2 lines
Right now, I'm at a loss to explain the corruption, so it's difficult to suggest what to try.
The thing is here, this is PCIE, so if there is a GPU plugged into the PCIE 16x slot in theory the main onboard graphics should disable, AGP code is used to control the GART for the onboard chip, in this case a plugged in card will not use AGP, I wonder have Intel tested with a pcie card in place...
Agree. We seem to always enable AGP even IGD is disabled or not exists, other card should not depend on this module ever.
Quoted 2 lines
That is Chinese for me :/.
Do you want me to try something?Carlo, I've just built latest kernel git tree on a Dell 965G box and have a NV card plugged-in. It boots fine.
Quoted 8 lines
Linux agpgart interface v0.102 (c) Dave Jones
agpgart: Detected an Intel 965G Chipset.
agpgart: AGP aperture is 256M @0x0I don't know why it hangs your machine when loading this module, it should just not bother anything. But from your last "modprobe: ..." line, it seems there's really badness somewhere, do you have serial console to see more in the message?
Quoted 4 lines
There are also these bug reports:
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=229913
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=242101
good find.
Looking through intel-agp brings up a wart that I've been complaining about for a while.
Start looking for functions with '965' in them.
the first one you hit is the wonderfully named 'intel_i830_init_gtt_entries'.
Two thirds of that function no longer have anything to do with an i830. Instead of adding a intel_i965_init_gtt_entries, this thing has grown into a monster dealing with three different generations of hardware.
This results in tables like this..
static const struct agp_bridge_driver intel_i965_driver = {
.owner = THIS_MODULE,
.aperture_sizes = intel_i830_sizes,
.size_type = FIXED_APER_SIZE,
.num_aperture_sizes = 4,
.needs_scratch_page = TRUE,
.configure = intel_i915_configure,
.fetch_size = intel_i9xx_fetch_size,
.cleanup = intel_i915_cleanup,
.tlb_flush = intel_i810_tlbflush,
.mask_memory = intel_i965_mask_memory,
.masks = intel_i810_masks,
.agp_enable = intel_i810_agp_enable,
.cache_flush = global_cache_flush,
.create_gatt_table = intel_i965_create_gatt_table,
.free_gatt_table = intel_i830_free_gatt_table,
.insert_memory = intel_i915_insert_entries,
.remove_memory = intel_i915_remove_entries,
.alloc_by_type = intel_i830_alloc_by_type,
.free_by_type = intel_i810_free_by_type,
.agp_alloc_page = agp_generic_alloc_page,
.agp_destroy_page = agp_generic_destroy_page,
.agp_type_to_mask_type = intel_i830_type_to_mask_type,so we use bits and pieces from 810, 830, 915, and throw in some new 965 routines too. Why is this a mess ? Because it's non-trivial to just look at this table and spot bugs like "wait, that 810 should be using 915" without lots of staring at data sheets. Additionally each time we twist these routines to cope with an additional chipset, we risk breaking previous generations.
Having functions do ONE thing is a good thing, even if it means having 15 of them that look similar. The alternative of a single function that becomes a nest of if's & switches is just horrible.
It could be that all of the above is actually pointing to the correct routines. It could also be that the codepaths in those routines, as twisty as they are, are fine, and this is just some normal bug, but hunting for it becomes a lot harder when the code is this baroque.
Dave
Signature · 1 line
http://www.codemonkey.org.uk
Re: [AGPGART] intel_agp: use table for device probe
In reply to Chuck EbbertQuoted 4 lines · Chuck Ebbert
There are also these bug reports:
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=229913
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=242101
I managed to set up a serial console for booting, and because of these bug reports tried to boot 2.6.22-rc5 with and without agp=off. With agp=off it does indeed boot fine.
Here is the result for both cases (I've been so free to remove any occurance of ^M and replace ESC with the two characters ^[):
rawserial-master-188e1:
Press any key to continue.
Press any key to continue.
Press any key to continue.
Press any key to continue.
Press any key to continue.
Press any key to continue.
Press any key to continue.
^[[H^[[J
GNU GRUB version 0.97 (635K lower / 2095680K upper memory)
^[[m^[[4;2H+-------------------------------------------------------------------------+^[[5;2H|^[[5;76H|^[[6;2H|^[[6;76H|^[[7;2H|^[[7;76H|^[[8;2H|^[[8;76H|^[[9;2H|^[[9;76H|^[[10;2H|^[[10;76H|^[[11;2H|^[[11;76H|^[[12;2H|^[[12;76H|^[[13;2H|^[[13;76H|^[[14;2H|^[[14;76H|^[[15;2H|^[[15;76H|^[[16;2H|^[[16;76H|^[[17;2H+-------------------------------------------------------------------------+^[[m
Use the ^ and v keys to select which entry is highlighted.
Press enter to boot the selected OS, 'e' to edit the
commands before booting, or 'c' for a command-line.^[[5;78H ^[[m^[[7m^[[5;3H Debian GNU/Linux, kernel 2.6.22-rc5-master-188e1f81ba31af1b65a2f3611d> ^[[5;75H^[[m^[[m^[[6;3H Debian GNU/Linux, kernel 2.6.22-rc5-master-188e1f81ba31af1b65a2f3611d> ^[[6;75H^[[m^[[m^[[7;3H Debian GNU/Linux, kernel 2.6.22-rc4-hikaru-amd64 ^[[7;75H^[[m^[[m^[[8;3H Debian GNU/Linux, kernel 2.6.22-rc4-hikaru-amd64 (single-user mode) ^[[8;75H^[[m^[[m^[[9;3H Debian GNU/Linux, kernel 2.6.18-4-amd64 ^[[9;75H^[[m^[[m^[[10;3H Debian GNU/Linux, kernel 2.6.18-4-amd64 (single-user mode) ^[[10;75H^[[m^[[m^[[11;3H ^[[11;75H^[[m^[[m^[[12;3H ^[[12;75H^[[m^[[m^[[13;3H ^[[13;75H^[[m^[[m^[[14;3H ^[[14;75H^[[m^[[m^[[15;3H ^[[15;75H^[[m^[[m^[[16;3H ^[[16;75H^[[m^[[16;78H ^[[5;75H^[[23;4H The highlighted entry will be booted automatically in 5 seconds. ^[[5;75H^[[23;4H The highlighted entry will be booted automatically in 4 seconds. ^[[5;75H^[[23;4H The highlighted entry will be booted automatically in 3 seconds. ^[[5;75H^[[23;4H The highlighted entry will be booted automatically in 2 seconds. ^[[5;75H^[[23;4H ^[[5;75H^[[m^[[5;3H Debian GNU/Linux, kernel 2.6.22-rc5-master-188e1f81ba31af1b65a2f3611d> ^[[5;75H^[[m^[[m^[[7m^[[6;3H Debian GNU/Linux, kernel 2.6.22-rc5-master-188e1f81ba31af1b65a2f3611d> ^[[6;75H^[[m^[[m^[[6;3H Debian GNU/Linux, kernel 2.6.22-rc5-master-188e1f81ba31af1b65a2f3611d> ^[[6;75H^[[m^[[m^[[7m^[[5;3H Debian GNU/Linux, kernel 2.6.22-rc5-master-188e1f81ba31a!
f1b65a2f
3611d> ^[[5;75H^[[m^[[H^[[J Booting 'Debian GNU/Linux, kernel 2.6.22-rc5-master-188e1f81ba31af1b65a2f3611
df4c670b092bbac-amd64'
root (hd0,0)
Filesystem type is ext2fs, partition type 0xfd
kernel /vmlinuz-2.6.22-rc5-master-188e1f81ba31af1b65a2f3611df4c670b092bbac-amd 64 root=/dev/md2 ro console=tty0 console=ttyS0,38400n8
[Linux-bzImage, setup=0x1e00, size=0x17ac68]
initrd /initrd.img-2.6.22-rc5-master-188e1f81ba31af1b65a2f3611df4c670b092bbac- amd64
[Linux-initrd @ 0x379e6000, 0x60989e bytes]
savedefault
Linux version 2.6.22-rc5-master-188e1f81ba31af1b65a2f3611df4c670b092bbac-amd64 (carlo@hikaru) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP Sun Jun 17 18:45:05 CEST 2007 Command line: root=/dev/md2 ro console=tty0 console=ttyS0,38400n8
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009ec00 (usable)
BIOS-e820: 000000000009ec00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007ff90000 (usable)
BIOS-e820: 000000007ff90000 - 000000007ff9e000 (ACPI data)
BIOS-e820: 000000007ff9e000 - 000000007ffe0000 (ACPI NVS)
BIOS-e820: 000000007ffe0000 - 0000000080000000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 0000000180000000 (usable)end_pfn_map = 1572864
DMI 2.4 present.
ACPI: RSDP 000FAE40, 0024 (r2 ACPIAM)
ACPI: XSDT 7FF90100, 0054 (r1 ÿÿÿÿÿÿ ÿÿÿÿÿÿÿÿ 3000709 MSFT 97)
ACPI: FACP 7FF90290, 00F4 (r3 MSTEST OEMFACP 3000709 MSFT 97)
ACPI: DSDT 7FF905C0, 8E7D (r1 A0483 A0483035 35 INTL 20060113)
ACPI: FACS 7FF9E000, 0040
ACPI: APIC 7FF90390, 006C (r1 MSTEST OEMAPIC 3000709 MSFT 97)
ACPI: MCFG 7FF90400, 003C (r1 MSTEST OEMMCFG 3000709 MSFT 97)
ACPI: SLIC 7FF90440, 0176 (r1 ÿÿÿÿÿÿ ÿÿÿÿÿÿÿÿ 3000709 MSFT 97)
ACPI: OEMB 7FF9E040, 007B (r1 MSTEST AMI_OEM 3000709 MSFT 97)
ACPI: HPET 7FF99440, 0038 (r1 MSTEST OEMHPET 3000709 MSFT 97)
No NUMA configuration found
Faking a node at 0000000000000000-0000000180000000
Bootmem setup node 0 0000000000000000-0000000180000000
Zone PFN ranges:
DMA 0 -> 4096
DMA32 4096 -> 1048576
Normal 1048576 -> 1572864
early_node_map[3] active PFN ranges
0: 0 -> 158
0: 256 -> 524176
0: 1048576 -> 1572864ACPI: PM-Timer IO Port: 0x808
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
Processor #2
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] enabled)
Processor #1
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
Processor #3
ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 4, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Setting APIC routing to flat
ACPI: HPET id: 0x8086a202 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
swsusp: Registered nosave memory region: 000000000009e000 - 000000000009f000
swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e4000
swsusp: Registered nosave memory region: 00000000000e4000 - 0000000000100000
swsusp: Registered nosave memory region: 000000007ff90000 - 000000007ff9e000
swsusp: Registered nosave memory region: 000000007ff9e000 - 000000007ffe0000
swsusp: Registered nosave memory region: 000000007ffe0000 - 0000000080000000
swsusp: Registered nosave memory region: 0000000080000000 - 00000000fee00000
swsusp: Registered nosave memory region: 00000000fee00000 - 00000000fee01000
swsusp: Registered nosave memory region: 00000000fee01000 - 00000000ffb00000
swsusp: Registered nosave memory region: 00000000ffb00000 - 0000000100000000
Allocating PCI resources starting at 88000000 (gap: 80000000:7ee00000)
SMP: Allowing 4 CPUs, 0 hotplug CPUs
PERCPU: Allocating 37768 bytes of per cpu data
Built 1 zonelists. Total pages: 1025869
Kernel command line: root=/dev/md2 ro console=tty0 console=ttyS0,38400n8
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Extended CMOS year: 2000time.c: Detected 2666.666 MHz processor.
Console: colour VGA+ 80x25
Checking aperture...
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
Placing software IO TLB between 0x1059000 - 0x5059000
Memory: 4030964k/6291456k available (2015k kernel code, 162500k reserved, 947k data, 296k init) Calibrating delay using timer specific routine.. 5336.91 BogoMIPS (lpj=10673826)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Mount-cache hash table entries: 256
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L3 cache: 4096K
CPU 0/0 -> Node 0
using mwait in idle threads.
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU0: Thermal monitoring enabled (TM2)
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
Using local APIC timer interrupts.
result 16666650
Detected 16.666 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/4 APIC 0x2
Initializing CPU#1
Calibrating delay using timer specific routine.. 5333.56 BogoMIPS (lpj=10667122)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L3 cache: 4096K
CPU 1/2 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU1: Thermal monitoring enabled (TM2)
Intel(R) Core(TM)2 Quad CPU @ 2.66GHz stepping 07
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
SMP alternatives: switching to SMP code
Booting processor 2/4 APIC 0x1
Initializing CPU#2
Calibrating delay using timer specific routine.. 5333.39 BogoMIPS (lpj=10666789)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L3 cache: 4096K
CPU 2/1 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU2: Thermal monitoring enabled (TM2)
Intel(R) Core(TM)2 Quad CPU @ 2.66GHz stepping 07
checking TSC synchronization [CPU#0 -> CPU#2]: passed.
SMP alternatives: switching to SMP code
Booting processor 3/4 APIC 0x3
Initializing CPU#3
Calibrating delay using timer specific routine.. 5333.36 BogoMIPS (lpj=10666733)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L3 cache: 4096K
CPU 3/3 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU3: Thermal monitoring enabled (TM2)
Intel(R) Core(TM)2 Quad CPU @ 2.66GHz stepping 07
checking TSC synchronization [CPU#0 -> CPU#3]: passed.
Brought up 4 CPUs
migration_cost=3360
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: Using configuration type 1
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 0480-04bf claimed by ICH6 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 *15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 *14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 15 devices
ACPI: ACPI bus type pnp unregistered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NET: Registered protocol family 8
NET: Registered protocol family 20
PCI-GART: No AMD northbridge found.
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 64-bit timers, 14318180 Hz
ACPI: RTC can wake from S4
pnp: 00:01: iomem range 0xfed14000-0xfed19fff has been reserved
pnp: 00:07: ioport range 0x290-0x297 has been reserved
pnp: 00:08: iomem range 0xffafe000-0xffb0cbff could not be reserved
pnp: 00:08: iomem range 0xffb00000-0xffbfffff could not be reserved
pnp: 00:08: iomem range 0xfed1c000-0xfed1ffff has been reserved
pnp: 00:08: iomem range 0xfed20000-0xfed8ffff has been reserved
pnp: 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved
pnp: 00:0a: iomem range 0xfee00000-0xfee00fff could not be reserved
pnp: 00:0d: iomem range 0xe0000000-0xefffffff has been reserved
pnp: 00:0e: iomem range 0x0-0x9ffff could not be reserved
pnp: 00:0e: iomem range 0xc0000-0xcffff has been reserved
Time: tsc clocksource has been installed.
pnp: 00:0e: iomem range 0xe0000-0xfffff could not be reserved
pnp: 00:0e: iomem range 0x100000-0x7fffffff could not be reserved
PCI: Bridge: 0000:00:01.0
IO window: a000-afff
MEM window: f8800000-fe8fffff
PREFETCH window: bfe00000-dfdfffff
PCI: Bridge: 0000:00:1c.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: dfe00000-dfefffff
PCI: Bridge: 0000:00:1c.5
IO window: b000-bfff
MEM window: fe900000-fe9fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
IO window: c000-cfff
MEM window: fea00000-feafffff
PREFETCH window: disabled.
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
ACPI: PCI Interrupt 0000:00:1c.5[B] -> GSI 17 (level, low) -> IRQ 17
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 524288 (order: 11, 12582912 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 524288 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 6182k freed
audit: initializing netlink socket (disabled)
audit(1182191783.492:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)assign_interrupt_mode Found MSI capabilityassign_interrupt_mode Found MSI capabilityassign_interrupt_mode Found MSI capability
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.102 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
input: AT Translated Set 2 keyboard as /class/input/input0
Freeing unused kernel memory: 296k freed
Loading, please wait...
Begin: Loading essential drivers... ...
Done.
Begin: Running /scripts/init-premount ...
ACPI Warning (tbutils-0158): Incorrect checksum in table [OEMB] - F5, should be F4 [20070126]
ACPI: SSDT 7FF9E0C0, 0208 (r1 AMI CPU1PM 1 INTL 20060113)
ACPI: SSDT 7FF9E2D0, 013A (r1 AMI CPU2PM 1 INTL 20060113)
ACPI: SSDT 7FF9E410, 013A (r1 AMI CPU3PM 1 INTL 20060113)
ACPI: SSDT 7FF9E550, 013A (r1 AMI CPU4PM 1 INTL 20060113)
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 16uhci_hcd 0000:00:1a.0: UHCI Host Controlleruhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000e000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
SCSI subsystem initialized
ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 17 (level, low) -> IRQ 17uhci_hcd 0000:00:1a.1: UHCI Host Controlleruhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2uhci_hcd 0000:00:1a.1: irq 17, io base 0x0000e080
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23uhci_hcd 0000:00:1d.0: UHCI Host Controlleruhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 3uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000d800
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19uhci_hcd 0000:00:1d.1: UHCI Host Controlleruhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 4uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000d880
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18uhci_hcd 0000:00:1d.2: UHCI Host Controlleruhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 5uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000dc00
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 18ehci_hcd 0000:00:1a.7: EHCI Host Controllerehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 6
usb 4-2: new low speed USB device using uhci_hcd and address 2ehci_hcd 0000:00:1a.7: debug port 1ehci_hcd 0000:00:1a.7: irq 18, io mem 0xfebff400ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 4 ports detected
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23ehci_hcd 0000:00:1d.7: EHCI Host Controllerehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 7ehci_hcd 0000:00:1d.7: debug port 1ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfebff000ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb 4-2: configuration #1 chosen from 1 choice
usb 4-2: can't set config #1, error -71
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 6 ports detected
usb 4-2: USB disconnect, address 2
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
usb 4-2: new low speed USB device using uhci_hcd and address 3
usb 4-2: configuration #1 chosen from 1 choice
usbcore: registered new interface driver hiddev
input: Microsoft Microsoft Wireless Intellimouse Explorer® 1.0A as /class/input/input1
input: USB HID v1.10 Mouse [Microsoft Microsoft Wireless Intellimouse Explorer® 1.0A] on usb-0000:00:1d.1-2
usbcore: registered new interface driver usbhiddrivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 6 ports 3 Gbps 0x3f impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq ilck stag pm led clo pmp pio slum part
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
scsi4 : ahci
scsi5 : ahci
ata1: SATA max UDMA/133 cmd 0xffffc20001448900 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
ata2: SATA max UDMA/133 cmd 0xffffc20001448980 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
ata3: SATA max UDMA/133 cmd 0xffffc20001448a00 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
ata4: SATA max UDMA/133 cmd 0xffffc20001448a80 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
ata5: SATA max UDMA/133 cmd 0xffffc20001448b00 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
ata6: SATA max UDMA/133 cmd 0xffffc20001448b80 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ata_hpa_resize 1: sectors = 145226112, hpa_sectors = 145226112
ata1.00: ATA-7: WDC WD740ADFD-00NLR1, 20.07P20, max UDMA/133
ata1.00: 145226112 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata1.00: ata_hpa_resize 1: sectors = 145226112, hpa_sectors = 145226112
ata1.00: configured for UDMA/133
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.00: ata_hpa_resize 1: sectors = 145226112, hpa_sectors = 145226112
ata2.00: ATA-7: WDC WD740ADFD-00NLR1, 20.07P20, max UDMA/133
ata2.00: 145226112 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata2.00: ata_hpa_resize 1: sectors = 145226112, hpa_sectors = 145226112
ata2.00: configured for UDMA/133
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: ata_hpa_resize 1: sectors = 145226112, hpa_sectors = 145226112
ata3.00: ATA-7: WDC WD740ADFD-00NLR1, 20.07P20, max UDMA/133
ata3.00: 145226112 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata3.00: ata_hpa_resize 1: sectors = 145226112, hpa_sectors = 145226112
ata3.00: configured for UDMA/133
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4.00: ata_hpa_resize 1: sectors = 625142448, hpa_sectors = 625142448
ata4.00: ATA-7: ST3320620AS, 3.AAE, max UDMA/133
ata4.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata4.00: ata_hpa_resize 1: sectors = 625142448, hpa_sectors = 625142448
ata4.00: configured for UDMA/133
ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata5.00: ATAPI: LITE-ON DVDRW LH-20A1S, 9L02, max UDMA/100
ata5.00: configured for UDMA/100
ata6: SATA link down (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access ATA WDC WD740ADFD-00 20.0 PQ: 0 ANSI: 5 scsi 1:0:0:0: Direct-Access ATA WDC WD740ADFD-00 20.0 PQ: 0 ANSI: 5 scsi 2:0:0:0: Direct-Access ATA WDC WD740ADFD-00 20.0 PQ: 0 ANSI: 5 scsi 3:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5 scsi 4:0:0:0: CD-ROM LITE-ON DVDRW LH-20A1S 9L02 PQ: 0 ANSI: 5
ACPI: PCI Interrupt 0000:04:03.0[A] -> GSI 21 (level, low) -> IRQ 21
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[21] MMIO=[feaff800-feafffff] Max Packet=[2048] IR/IT contexts=[4/8] sd 0:0:0:0: [sda] 145226112 512-byte hardware sectors (74356 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 145226112 512-byte hardware sectors (74356 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 >
sd 0:0:0:0: [sda] Attached SCSI disk
sd 1:0:0:0: [sdb] 145226112 512-byte hardware sectors (74356 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sdb] 145226112 512-byte hardware sectors (74356 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 sdb6 sdb7 sdb8 sdb9 sdb10 >
sd 1:0:0:0: [sdb] Attached SCSI disk
sd 2:0:0:0: [sdc] 145226112 512-byte hardware sectors (74356 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:0:0:0: [sdc] 145226112 512-byte hardware sectors (74356 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1 sdc2 sdc3 sdc4 < sdc5 sdc6 sdc7 sdc8 sdc9 sdc10 >
sd 2:0:0:0: [sdc] Attached SCSI disk
sd 3:0:0:0: [sdd] 625142448 512-byte hardware sectors (320073 MB)
sd 3:0:0:0: [sdd] Write Protect is off
sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 3:0:0:0: [sdd] 625142448 512-byte hardware sectors (320073 MB)
sd 3:0:0:0: [sdd] Write Protect is off
sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdd: sdd1 sdd2 sdd3
sd 3:0:0:0: [sdd] Attached SCSI disk
sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 1:0:0:0: Attached scsi generic sg1 type 0
sd 2:0:0:0: Attached scsi generic sg2 type 0
sd 3:0:0:0: Attached scsi generic sg3 type 0
sr 4:0:0:0: Attached scsi generic sg4 type 5
Done.
Begin: Mounting root file system... ...
Begin: Running /scripts/local-top ...
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Begin: Loading Mmd: raid1 personality registered for level 1
D modules ...
raid5: automatically using best checksumming function: generic_sse
Success: loaded module raid1.
generic_sse: 9514.000 MB/sec
raid5: using function: generic_sse (9514.000 MB/sec)
raid6: int64x1 2500 MB/s
raid6: int64x2 3017 MB/s
raid6: int64x4 2881 MB/s
raid6: int64x8 1921 MB/s
raid6: sse2x1 4193 MB/s
raid6: sse2x2 4612 MB/s
raid6: sse2x4 7864 MB/s
raid6: using algorithm sse2x4 (7864 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
Success: loaded module raid456.
Done.
Begin: Amd: md0 stopped.
ssembling all MD arrays ...
md: bind<sdb1>
md: bind<sdc1>
md: bind<sda1>
raid1: raid set md0 active with 3 out of 3 mirrors
mdadm: /dev/md0 md: md1 stopped.
has been started with 3 drives.
md: bind<sdb2>
md: bind<sdc2>
md: bind<sda2>
raid5: device sda2 operational as raid disk 0
raid5: device sdc2 operational as raid disk 2
raid5: device sdb2 operational as raid disk 1
raid5: allocated 3212kB for md1
raid5: raid level 5 set md1 active with 3 out of 3 devices, algorithm 2
RAID5 conf printout:
--- rd:3 wd:3
disk 0, o:1, dev:sda2
disk 1, o:1, dev:sdb2
disk 2, o:1, dev:sdc2
mdadm: /dev/md1 md: md2 stopped.
has been started with 3 drives.
md: bind<sdb3>
md: bind<sdc3>
md: bind<sda3>
raid5: device sda3 operational as raid disk 0
raid5: device sdc3 operational as raid disk 2
raid5: device sdb3 operational as raid disk 1
raid5: allocated 3212kB for md2
raid5: raid level 5 set md2 active with 3 out of 3 devices, algorithm 2
RAID5 conf printout:
--- rd:3 wd:3
disk 0, o:1, dev:sda3
disk 1, o:1, dev:sdb3
disk 2, o:1, dev:sdc3
mdadm: /dev/md2 md: md3 stopped.
has been started with 3 drives.
md: bind<sdb5>
md: bind<sdc5>
md: bind<sda5>
raid5: device sda5 operational as raid disk 0
raid5: device sdc5 operational as raid disk 2
raid5: device sdb5 operational as raid disk 1
raid5: allocated 3212kB for md3
raid5: raid level 5 set md3 active with 3 out of 3 devices, algorithm 2
RAID5 conf printout:
--- rd:3 wd:3
disk 0, o:1, dev:sda5
disk 1, o:1, dev:sdb5
disk 2, o:1, dev:sdc5
mdadm: /dev/md3 md: md4 stopped.
has been started with 3 drives.
md: bind<sdb6>
md: bind<sdc6>
md: bind<sda6>
raid5: device sda6 operational as raid disk 0
raid5: device sdc6 operational as raid disk 2
raid5: device sdb6 operational as raid disk 1
raid5: allocated 3212kB for md4
raid5: raid level 5 set md4 active with 3 out of 3 devices, algorithm 2
RAID5 conf printout:
--- rd:3 wd:3
disk 0, o:1, dev:sda6
disk 1, o:1, dev:sdb6
disk 2, o:1, dev:sdc6
mdadm: /dev/md4 md: md5 stopped.
has been started with 3 drives.
md: bind<sdb7>
md: bind<sdc7>
md: bind<sda7>
raid5: device sda7 operational as raid disk 0
raid5: device sdc7 operational as raid disk 2
raid5: device sdb7 operational as raid disk 1
raid5: allocated 3212kB for md5
raid5: raid level 5 set md5 active with 3 out of 3 devices, algorithm 2
RAID5 conf printout:
--- rd:3 wd:3
disk 0, o:1, dev:sda7
disk 1, o:1, dev:sdb7
disk 2, o:1, dev:sdc7
mdadm: /dev/md5 md: md6 stopped.
has been started with 3 drives.
md: bind<sdb8>
md: bind<sdc8>
md: bind<sda8>
raid5: device sda8 operational as raid disk 0
raid5: device sdc8 operational as raid disk 2
raid5: device sdb8 operational as raid disk 1
raid5: allocated 3212kB for md6
raid5: raid level 5 set md6 active with 3 out of 3 devices, algorithm 2
RAID5 conf printout:
--- rd:3 wd:3
disk 0, o:1, dev:sda8
disk 1, o:1, dev:sdb8
disk 2, o:1, dev:sdc8
mdadm: /dev/md6 md: md7 stopped.
has been started with 3 drives.
md: bind<sdb9>
md: bind<sdc9>
md: bind<sda9>
raid5: device sda9 operational as raid disk 0
raid5: device sdc9 operational as raid disk 2
raid5: device sdb9 operational as raid disk 1
raid5: allocated 3212kB for md7
raid5: raid level 5 set md7 active with 3 out of 3 devices, algorithm 2
RAID5 conf printout:
--- rd:3 wd:3
disk 0, o:1, dev:sda9
disk 1, o:1, dev:sdb9
disk 2, o:1, dev:sdc9
mdadm: /dev/md7 md: md8 stopped.
has been started with 3 drives.
md: bind<sdb10>
md: bind<sdc10>
md: bind<sda10>
raid5: device sda10 operational as raid disk 0
raid5: device sdc10 operational as raid disk 2
raid5: device sdb10 operational as raid disk 1
raid5: allocated 3212kB for md8
raid5: raid level 5 set md8 active with 3 out of 3 devices, algorithm 2
RAID5 conf printout:
--- rd:3 wd:3
disk 0, o:1, dev:sda10
disk 1, o:1, dev:sdb10
disk 2, o:1, dev:sdc10
mdadm: /dev/md8 has been started with 3 drives.
Success: assembled all arrays.
Done.
Begin: Executing udevtrigger again ...
Done.
Done.
Begin: Running /scripts/local-premount ...
Attempting manual resume
kinit: name_to_dev_t(/dev/md1) = md1(9,1)
kinit: trying to resume from /dev/md1
kinit: No resume image, doing normal boot...
Done.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Begin: Running /scripts/local-bottom ...
Done.
Done.
Begin: Running /scripts/init-bottom ...
Done.
Mount failed for selinuxfs on /selinux: No such device
INIT: version 2.86 booting
Starting the hotplug events dispatcher: udevd.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...agpgart: Detected an Intel 965G Chipset.
======================================================================================
rawserial-master-188e1-agp=off:
Press any key to continue.
Press any key to continue.
Press any key to continue.
Press any key to continue.
^[[H^[[J
GNU GRUB version 0.97 (635K lower / 2095680K upper memory)
^[[m^[[4;2H+-------------------------------------------------------------------------+^[[5;2H|^[[5;76H|^[[6;2H|^[[6;76H|^[[7;2H|^[[7;76H|^[[8;2H|^[[8;76H|^[[9;2H|^[[9;76H|^[[10;2H|^[[10;76H|^[[11;2H|^[[11;76H|^[[12;2H|^[[12;76H|^[[13;2H|^[[13;76H|^[[14;2H|^[[14;76H|^[[15;2H|^[[15;76H|^[[16;2H|^[[16;76H|^[[17;2H+-------------------------------------------------------------------------+^[[m
Use the ^ and v keys to select which entry is highlighted.
Press enter to boot the selected OS, 'e' to edit the
commands before booting, or 'c' for a command-line.^[[5;78H ^[[m^[[7m^[[5;3H Debian GNU/Linux, kernel 2.6.22-rc5-master-188e1f81ba31af1b65a2f3611d> ^[[5;75H^[[m^[[m^[[6;3H Debian GNU/Linux, kernel 2.6.22-rc5-master-188e1f81ba31af1b65a2f3611d> ^[[6;75H^[[m^[[m^[[7;3H Debian GNU/Linux, kernel 2.6.22-rc4-hikaru-amd64 ^[[7;75H^[[m^[[m^[[8;3H Debian GNU/Linux, kernel 2.6.22-rc4-hikaru-amd64 (single-user mode) ^[[8;75H^[[m^[[m^[[9;3H Debian GNU/Linux, kernel 2.6.18-4-amd64 ^[[9;75H^[[m^[[m^[[10;3H Debian GNU/Linux, kernel 2.6.18-4-amd64 (single-user mode) ^[[10;75H^[[m^[[m^[[11;3H ^[[11;75H^[[m^[[m^[[12;3H ^[[12;75H^[[m^[[m^[[13;3H ^[[13;75H^[[m^[[m^[[14;3H ^[[14;75H^[[m^[[m^[[15;3H ^[[15;75H^[[m^[[m^[[16;3H ^[[16;75H^[[m^[[16;78H ^[[5;75H^[[23;4H The highlighted entry will be booted automatically in 5 seconds. ^[[5;75H^[[23;4H The highlighted entry will be booted automatically in 4 seconds. ^[[5;75H^[[23;4H The highlighted entry will be booted automatically in 3 seconds. ^[[5;75H^[[23;4H ^[[5;75H^[[m^[[5;3H Debian GNU/Linux, kernel 2.6.22-rc5-master-188e1f81ba31af1b65a2f3611d> ^[[5;75H^[[m^[[m^[[7m^[[6;3H Debian GNU/Linux, kernel 2.6.22-rc5-master-188e1f81ba31af1b65a2f3611d> ^[[6;75H^[[m^[[m^[[6;3H Debian GNU/Linux, kernel 2.6.22-rc5-master-188e1f81ba31af1b65a2f3611d> ^[[6;75H^[[m^[[m^[[7m^[[5;3H Debian GNU/Linux, kernel 2.6.22-rc5-master-188e1f81ba31af1b65a2f3611d> ^[[5;75H^[[m^[[H^[[J Booting 'Debian GNU/Linux, kernel 2.6.22-rc5-m!
aster-188e1f81ba31af1b65a2f3611
df4c670b092bbac-amd64'
root (hd0,0)
Filesystem type is ext2fs, partition type 0xfd
kernel /vmlinuz-2.6.22-rc5-master-188e1f81ba31af1b65a2f3611df4c670b092bbac-amd 64 root=/dev/md2 ro console=tty0 console=ttyS0,38400n8 agp=off
[Linux-bzImage, setup=0x1e00, size=0x17ac68]
initrd /initrd.img-2.6.22-rc5-master-188e1f81ba31af1b65a2f3611df4c670b092bbac- amd64
[Linux-initrd @ 0x379e6000, 0x60989e bytes]
savedefault
Linux version 2.6.22-rc5-master-188e1f81ba31af1b65a2f3611df4c670b092bbac-amd64 (carlo@hikaru) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP Sun Jun 17 18:45:05 CEST 2007 Command line: root=/dev/md2 ro console=tty0 console=ttyS0,38400n8 agp=off
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009ec00 (usable)
BIOS-e820: 000000000009ec00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007ff90000 (usable)
BIOS-e820: 000000007ff90000 - 000000007ff9e000 (ACPI data)
BIOS-e820: 000000007ff9e000 - 000000007ffe0000 (ACPI NVS)
BIOS-e820: 000000007ffe0000 - 0000000080000000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 0000000180000000 (usable)end_pfn_map = 1572864
DMI 2.4 present.
ACPI: RSDP 000FAE40, 0024 (r2 ACPIAM)
ACPI: XSDT 7FF90100, 0054 (r1 ÿÿÿÿÿÿ ÿÿÿÿÿÿÿÿ 3000709 MSFT 97)
ACPI: FACP 7FF90290, 00F4 (r3 MSTEST OEMFACP 3000709 MSFT 97)
ACPI: DSDT 7FF905C0, 8E7D (r1 A0483 A0483035 35 INTL 20060113)
ACPI: FACS 7FF9E000, 0040
ACPI: APIC 7FF90390, 006C (r1 MSTEST OEMAPIC 3000709 MSFT 97)
ACPI: MCFG 7FF90400, 003C (r1 MSTEST OEMMCFG 3000709 MSFT 97)
ACPI: SLIC 7FF90440, 0176 (r1 ÿÿÿÿÿÿ ÿÿÿÿÿÿÿÿ 3000709 MSFT 97)
ACPI: OEMB 7FF9E040, 007B (r1 MSTEST AMI_OEM 3000709 MSFT 97)
ACPI: HPET 7FF99440, 0038 (r1 MSTEST OEMHPET 3000709 MSFT 97)
No NUMA configuration found
Faking a node at 0000000000000000-0000000180000000
Bootmem setup node 0 0000000000000000-0000000180000000
Zone PFN ranges:
DMA 0 -> 4096
DMA32 4096 -> 1048576
Normal 1048576 -> 1572864
early_node_map[3] active PFN ranges
0: 0 -> 158
0: 256 -> 524176
0: 1048576 -> 1572864ACPI: PM-Timer IO Port: 0x808
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
Processor #2
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] enabled)
Processor #1
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
Processor #3
ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 4, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Setting APIC routing to flat
ACPI: HPET id: 0x8086a202 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
swsusp: Registered nosave memory region: 000000000009e000 - 000000000009f000
swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e4000
swsusp: Registered nosave memory region: 00000000000e4000 - 0000000000100000
swsusp: Registered nosave memory region: 000000007ff90000 - 000000007ff9e000
swsusp: Registered nosave memory region: 000000007ff9e000 - 000000007ffe0000
swsusp: Registered nosave memory region: 000000007ffe0000 - 0000000080000000
swsusp: Registered nosave memory region: 0000000080000000 - 00000000fee00000
swsusp: Registered nosave memory region: 00000000fee00000 - 00000000fee01000
swsusp: Registered nosave memory region: 00000000fee01000 - 00000000ffb00000
swsusp: Registered nosave memory region: 00000000ffb00000 - 0000000100000000
Allocating PCI resources starting at 88000000 (gap: 80000000:7ee00000)
SMP: Allowing 4 CPUs, 0 hotplug CPUs
PERCPU: Allocating 37768 bytes of per cpu data
Built 1 zonelists. Total pages: 1025869
Kernel command line: root=/dev/md2 ro console=tty0 console=ttyS0,38400n8 agp=off Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Extended CMOS year: 2000time.c: Detected 2666.669 MHz processor.
Console: colour VGA+ 80x25
Checking aperture...
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
Placing software IO TLB between 0x1059000 - 0x5059000
Memory: 4030964k/6291456k available (2015k kernel code, 162500k reserved, 947k data, 296k init) Calibrating delay using timer specific routine.. 5336.89 BogoMIPS (lpj=10673790)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Mount-cache hash table entries: 256
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L3 cache: 4096K
CPU 0/0 -> Node 0
using mwait in idle threads.
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU0: Thermal monitoring enabled (TM2)
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
Using local APIC timer interrupts.
result 16666671
Detected 16.666 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/4 APIC 0x2
Initializing CPU#1
Calibrating delay using timer specific routine.. 5333.45 BogoMIPS (lpj=10666915)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L3 cache: 4096K
CPU 1/2 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU1: Thermal monitoring enabled (TM2)
Intel(R) Core(TM)2 Quad CPU @ 2.66GHz stepping 07
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
SMP alternatives: switching to SMP code
Booting processor 2/4 APIC 0x1
Initializing CPU#2
Calibrating delay using timer specific routine.. 5333.58 BogoMIPS (lpj=10667172)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L3 cache: 4096K
CPU 2/1 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU2: Thermal monitoring enabled (TM2)
Intel(R) Core(TM)2 Quad CPU @ 2.66GHz stepping 07
checking TSC synchronization [CPU#0 -> CPU#2]: passed.
SMP alternatives: switching to SMP code
Booting processor 3/4 APIC 0x3
Initializing CPU#3
Calibrating delay using timer specific routine.. 5333.36 BogoMIPS (lpj=10666726)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L3 cache: 4096K
CPU 3/3 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU3: Thermal monitoring enabled (TM2)
Intel(R) Core(TM)2 Quad CPU @ 2.66GHz stepping 07
checking TSC synchronization [CPU#0 -> CPU#3]: passed.
Brought up 4 CPUs
migration_cost=3357
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: Using configuration type 1
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 0480-04bf claimed by ICH6 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 *15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 *14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 15 devices
ACPI: ACPI bus type pnp unregistered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NET: Registered protocol family 8
NET: Registered protocol family 20
PCI-GART: No AMD northbridge found.
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 64-bit timers, 14318180 Hz
ACPI: RTC can wake from S4
pnp: 00:01: iomem range 0xfed14000-0xfed19fff has been reserved
pnp: 00:07: ioport range 0x290-0x297 has been reserved
pnp: 00:08: iomem range 0xffafe000-0xffb0cbff could not be reserved
pnp: 00:08: iomem range 0xffb00000-0xffbfffff could not be reserved
pnp: 00:08: iomem range 0xfed1c000-0xfed1ffff has been reserved
pnp: 00:08: iomem range 0xfed20000-0xfed8ffff has been reserved
pnp: 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved
pnp: 00:0a: iomem range 0xfee00000-0xfee00fff could not be reserved
pnp: 00:0d: iomem range 0xe0000000-0xefffffff has been reserved
Time: tsc clocksource has been installed.
pnp: 00:0e: iomem range 0x0-0x9ffff could not be reserved
pnp: 00:0e: iomem range 0xc0000-0xcffff has been reserved
pnp: 00:0e: iomem range 0xe0000-0xfffff could not be reserved
pnp: 00:0e: iomem range 0x100000-0x7fffffff could not be reserved
PCI: Bridge: 0000:00:01.0
IO window: a000-afff
MEM window: f8800000-fe8fffff
PREFETCH window: bfe00000-dfdfffff
PCI: Bridge: 0000:00:1c.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: dfe00000-dfefffff
PCI: Bridge: 0000:00:1c.5
IO window: b000-bfff
MEM window: fe900000-fe9fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
IO window: c000-cfff
MEM window: fea00000-feafffff
PREFETCH window: disabled.
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
ACPI: PCI Interrupt 0000:00:1c.5[B] -> GSI 17 (level, low) -> IRQ 17
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 524288 (order: 11, 12582912 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 524288 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 6182k freed
audit: initializing netlink socket (disabled)
audit(1182191286.492:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)assign_interrupt_mode Found MSI capabilityassign_interrupt_mode Found MSI capabilityassign_interrupt_mode Found MSI capability
Real Time Clock Driver v1.12ac
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
input: AT Translated Set 2 keyboard as /class/input/input0
Freeing unused kernel memory: 296k freed
Loading, please wait...
Begin: Loading essential drivers... ...
Done.
Begin: Running /scripts/init-premount ...
ACPI Warning (tbutils-0158): Incorrect checksum in table [OEMB] - F5, should be F4 [20070126]
ACPI: SSDT 7FF9E0C0, 0208 (r1 AMI CPU1PM 1 INTL 20060113)
ACPI: SSDT 7FF9E2D0, 013A (r1 AMI CPU2PM 1 INTL 20060113)
ACPI: SSDT 7FF9E410, 013A (r1 AMI CPU3PM 1 INTL 20060113)
ACPI: SSDT 7FF9E550, 013A (r1 AMI CPU4PM 1 INTL 20060113)
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 16uhci_hcd 0000:00:1a.0: UHCI Host Controlleruhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000e000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
SCSI subsystem initialized
ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 17 (level, low) -> IRQ 17uhci_hcd 0000:00:1a.1: UHCI Host Controlleruhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2uhci_hcd 0000:00:1a.1: irq 17, io base 0x0000e080
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 18ehci_hcd 0000:00:1a.7: EHCI Host Controllerehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 3ehci_hcd 0000:00:1a.7: debug port 1ehci_hcd 0000:00:1a.7: irq 18, io mem 0xfebff400ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23uhci_hcd 0000:00:1d.0: UHCI Host Controlleruhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 4uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000d800
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19uhci_hcd 0000:00:1d.1: UHCI Host Controlleruhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 5uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000d880
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18uhci_hcd 0000:00:1d.2: UHCI Host Controlleruhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 6uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000dc00
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23ehci_hcd 0000:00:1d.7: EHCI Host Controllerehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 7
usb 5-2: new low speed USB device using uhci_hcd and address 2ehci_hcd 0000:00:1d.7: debug port 1ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfebff000ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 6 ports detected
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
usb 5-2: new low speed USB device using uhci_hcd and address 3
usb 5-2: configuration #1 chosen from 1 choice
usbcore: registered new interface driver hiddev
input: Microsoft Microsoft Wireless Intellimouse Explorer® 1.0A as /class/input/input1
input: USB HID v1.10 Mouse [Microsoft Microsoft Wireless Intellimouse Explorer® 1.0A] on usb-0000:00:1d.1-2
usbcore: registered new interface driver usbhiddrivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 6 ports 3 Gbps 0x3f impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq ilck stag pm led clo pmp pio slum part
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
scsi4 : ahci
scsi5 : ahci
ata1: SATA max UDMA/133 cmd 0xffffc20001448900 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
ata2: SATA max UDMA/133 cmd 0xffffc20001448980 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
ata3: SATA max UDMA/133 cmd 0xffffc20001448a00 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
ata4: SATA max UDMA/133 cmd 0xffffc20001448a80 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
ata5: SATA max UDMA/133 cmd 0xffffc20001448b00 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
ata6: SATA max UDMA/133 cmd 0xffffc20001448b80 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 0
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ata_hpa_resize 1: sectors = 145226112, hpa_sectors = 145226112
ata1.00: ATA-7: WDC WD740ADFD-00NLR1, 20.07P20, max UDMA/133
ata1.00: 145226112 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata1.00: ata_hpa_resize 1: sectors = 145226112, hpa_sectors = 145226112
ata1.00: configured for UDMA/133
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.00: ata_hpa_resize 1: sectors = 145226112, hpa_sectors = 145226112
ata2.00: ATA-7: WDC WD740ADFD-00NLR1, 20.07P20, max UDMA/133
ata2.00: 145226112 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata2.00: ata_hpa_resize 1: sectors = 145226112, hpa_sectors = 145226112
ata2.00: configured for UDMA/133
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: ata_hpa_resize 1: sectors = 145226112, hpa_sectors = 145226112
ata3.00: ATA-7: WDC WD740ADFD-00NLR1, 20.07P20, max UDMA/133
ata3.00: 145226112 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata3.00: ata_hpa_resize 1: sectors = 145226112, hpa_sectors = 145226112
ata3.00: configured for UDMA/133
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4.00: ata_hpa_resize 1: sectors = 625142448, hpa_sectors = 625142448
ata4.00: ATA-7: ST3320620AS, 3.AAE, max UDMA/133
ata4.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata4.00: ata_hpa_resize 1: sectors = 625142448, hpa_sectors = 625142448
ata4.00: configured for UDMA/133
ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata5.00: ATAPI: LITE-ON DVDRW LH-20A1S, 9L02, max UDMA/100
ata5.00: configured for UDMA/100
ata6: SATA link down (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access ATA WDC WD740ADFD-00 20.0 PQ: 0 ANSI: 5 scsi 1:0:0:0: Direct-Access ATA WDC WD740ADFD-00 20.0 PQ: 0 ANSI: 5 scsi 2:0:0:0: Direct-Access ATA WDC WD740ADFD-00 20.0 PQ: 0 ANSI: 5 scsi 3:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5 scsi 4:0:0:0: CD-ROM LITE-ON DVDRW LH-20A1S 9L02 PQ: 0 ANSI: 5
ACPI: PCI Interrupt 0000:04:03.0[A] -> GSI 21 (level, low) -> IRQ 21
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[21] MMIO=[feaff800-feafffff] Max Packet=[2048] IR/IT contexts=[4/8] sd 0:0:0:0: [sda] 145226112 512-byte hardware sectors (74356 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 145226112 512-byte hardware sectors (74356 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 >
sd 0:0:0:0: [sda] Attached SCSI disk
sd 1:0:0:0: [sdb] 145226112 512-byte hardware sectors (74356 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sdb] 145226112 512-byte hardware sectors (74356 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 sdb6 sdb7 sdb8 sdb9 sdb10 >
sd 1:0:0:0: [sdb] Attached SCSI disk
sd 2:0:0:0: [sdc] 145226112 512-byte hardware sectors (74356 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:0:0:0: [sdc] 145226112 512-byte hardware sectors (74356 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1 sdc2 sdc3 sdc4 < sdc5 sdc6 sdc7 sdc8 sdc9 sdc10 >
sd 2:0:0:0: [sdc] Attached SCSI disk
sd 3:0:0:0: [sdd] 625142448 512-byte hardware sectors (320073 MB)
sd 3:0:0:0: [sdd] Write Protect is off
sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 3:0:0:0: [sdd] 625142448 512-byte hardware sectors (320073 MB)
sd 3:0:0:0: [sdd] Write Protect is off
sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdd: sdd1 sdd2 sdd3
sd 3:0:0:0: [sdd] Attached SCSI disk
sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 1:0:0:0: Attached scsi generic sg1 type 0
sd 2:0:0:0: Attached scsi generic sg2 type 0
sd 3:0:0:0: Attached scsi generic sg3 type 0
sr 4:0:0:0: Attached scsi generic sg4 type 5
Done.
Begin: Mounting root file system... ...
Begin: Running /scripts/local-top ...
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Begin: Loading Mmd: raid1 personality registered for level 1
D modules ...
raid5: automatically using best checksumming function: generic_sse
Success: loaded module raid1.
generic_sse: 9512.000 MB/sec
raid5: using function: generic_sse (9512.000 MB/sec)
raid6: int64x1 2501 MB/s
raid6: int64x2 3018 MB/s
raid6: int64x4 2881 MB/s
raid6: int64x8 1921 MB/s
raid6: sse2x1 4208 MB/s
raid6: sse2x2 5243 MB/s
raid6: sse2x4 7870 MB/s
raid6: using algorithm sse2x4 (7870 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
Success: loaded module raid456.
Done.
Begin: Amd: md0 stopped.
ssembling all MD arrays ...
md: bind<sdb1>
md: bind<sdc1>
md: bind<sda1>
raid1: raid set md0 active with 3 out of 3 mirrors
mdadm: /dev/md0 md: md1 stopped.
has been started with 3 drives.
md: bind<sdb2>
md: bind<sdc2>
md: bind<sda2>
raid5: device sda2 operational as raid disk 0
raid5: device sdc2 operational as raid disk 2
raid5: device sdb2 operational as raid disk 1
raid5: allocated 3212kB for md1
raid5: raid level 5 set md1 active with 3 out of 3 devices, algorithm 2
RAID5 conf printout:
--- rd:3 wd:3
disk 0, o:1, dev:sda2
disk 1, o:1, dev:sdb2
disk 2, o:1, dev:sdc2
mdadm: /dev/md1 md: md2 stopped.
has been started with 3 drives.
md: bind<sdb3>
md: bind<sdc3>
md: bind<sda3>
raid5: device sda3 operational as raid disk 0
raid5: device sdc3 operational as raid disk 2
raid5: device sdb3 operational as raid disk 1
raid5: allocated 3212kB for md2
raid5: raid level 5 set md2 active with 3 out of 3 devices, algorithm 2
RAID5 conf printout:
--- rd:3 wd:3
disk 0, o:1, dev:sda3
disk 1, o:1, dev:sdb3
disk 2, o:1, dev:sdc3
mdadm: /dev/md2 md: md3 stopped.
has been started with 3 drives.
md: bind<sdb5>
md: bind<sdc5>
md: bind<sda5>
raid5: device sda5 operational as raid disk 0
raid5: device sdc5 operational as raid disk 2
raid5: device sdb5 operational as raid disk 1
raid5: allocated 3212kB for md3
raid5: raid level 5 set md3 active with 3 out of 3 devices, algorithm 2
RAID5 conf printout:
--- rd:3 wd:3
disk 0, o:1, dev:sda5
disk 1, o:1, dev:sdb5
disk 2, o:1, dev:sdc5
mdadm: /dev/md3 md: md4 stopped.
has been started with 3 drives.
md: bind<sdb6>
md: bind<sdc6>
md: bind<sda6>
raid5: device sda6 operational as raid disk 0
raid5: device sdc6 operational as raid disk 2
raid5: device sdb6 operational as raid disk 1
raid5: allocated 3212kB for md4
raid5: raid level 5 set md4 active with 3 out of 3 devices, algorithm 2
RAID5 conf printout:
--- rd:3 wd:3
disk 0, o:1, dev:sda6
disk 1, o:1, dev:sdb6
disk 2, o:1, dev:sdc6
mdadm: /dev/md4 md: md5 stopped.
has been started with 3 drives.
md: bind<sdb7>
md: bind<sdc7>
md: bind<sda7>
raid5: device sda7 operational as raid disk 0
raid5: device sdc7 operational as raid disk 2
raid5: device sdb7 operational as raid disk 1
raid5: allocated 3212kB for md5
raid5: raid level 5 set md5 active with 3 out of 3 devices, algorithm 2
RAID5 conf printout:
--- rd:3 wd:3
disk 0, o:1, dev:sda7
disk 1, o:1, dev:sdb7
disk 2, o:1, dev:sdc7
mdadm: /dev/md5 md: md6 stopped.
has been started with 3 drives.
md: bind<sdb8>
md: bind<sdc8>
md: bind<sda8>
raid5: device sda8 operational as raid disk 0
raid5: device sdc8 operational as raid disk 2
raid5: device sdb8 operational as raid disk 1
raid5: allocated 3212kB for md6
raid5: raid level 5 set md6 active with 3 out of 3 devices, algorithm 2
RAID5 conf printout:
--- rd:3 wd:3
disk 0, o:1, dev:sda8
disk 1, o:1, dev:sdb8
disk 2, o:1, dev:sdc8
mdadm: /dev/md6 md: md7 stopped.
has been started with 3 drives.
md: bind<sdb9>
md: bind<sdc9>
md: bind<sda9>
raid5: device sda9 operational as raid disk 0
raid5: device sdc9 operational as raid disk 2
raid5: device sdb9 operational as raid disk 1
raid5: allocated 3212kB for md7
raid5: raid level 5 set md7 active with 3 out of 3 devices, algorithm 2
RAID5 conf printout:
--- rd:3 wd:3
disk 0, o:1, dev:sda9
disk 1, o:1, dev:sdb9
disk 2, o:1, dev:sdc9
mdadm: /dev/md7 md: md8 stopped.
has been started with 3 drives.
md: bind<sdb10>
md: bind<sdc10>
md: bind<sda10>
raid5: device sda10 operational as raid disk 0
raid5: device sdc10 operational as raid disk 2
raid5: device sdb10 operational as raid disk 1
raid5: allocated 3212kB for md8
raid5: raid level 5 set md8 active with 3 out of 3 devices, algorithm 2
RAID5 conf printout:
--- rd:3 wd:3
disk 0, o:1, dev:sda10
disk 1, o:1, dev:sdb10
disk 2, o:1, dev:sdc10
mdadm: /dev/md8 has been started with 3 drives.
Success: assembled all arrays.
Done.
Begin: Executing udevtrigger again ...
Done.
Done.
Begin: Running /scripts/local-premount ...
Attempting manual resume
kinit: name_to_dev_t(/dev/md1) = md1(9,1)
kinit: trying to resume from /dev/md1
kinit: No resume image, doing kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
normal boot...
Done.
Begin: Running /scripts/local-bottom ...
Done.
Done.
Begin: Running /scripts/init-bottom ...
Done.
Mount failed for selinuxfs on /selinux: No such device
INIT: version 2.86 booting
Starting the hotplug events dispatcher: udevd.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (21-Jan-2007)iTCO_wdt: Found a ICH8 or ICH8R TCO device (Version=2, TCOBASE=0x0860)iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 17 (level, low) -> IRQ 17
sky2 0000:02:00.0: v1.14 addr 0xfe9fc000 irq 17 Yukon-EC Ultra (0xb4) rev 2
input: PC Speaker as /class/input/input2
sky2 eth0: addr 00:1a:92:3a:4a:c1
PCI: Enabling device 0000:00:1f.3 (0001 -> 0003)
ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 18 (level, low) -> IRQ 18
gameport: EMU10K1 is pci0000:04:02.1/gameport0, io 0xcc00, speed 1041kHz
ACPI: PCI Interrupt 0000:04:02.0[A] -> GSI 23 (level, low) -> IRQ 23
input: PS/2 Logitech Mouse as /class/input/input3
done.
Setting parameters of disc: (none).
Checking root file system...fsck 1.40-WIP (14-Nov-2006)/dev/md2: clean, 14667/488640 files, 100111/975904 blocks
done.
EXT3 FS on md2, internal journal
Setting the system clock..
Cleaning up ifupdown....
Loading kernel modules...loop: module loaded
coretemp coretemp.0: Using undocumented features, absolute temperature might be wrong!
coretemp coretemp.1: Using undocumented features, absolute temperature might be wrong!
coretemp coretemp.2: Using undocumented features, absolute temperature might be wrong!
coretemp coretemp.3: Using undocumented features, absolute temperature might be wrong!
done.
Loading device-mapper supportdevice-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: [email protected] .
Generating udev events for MD arrays...done.
Starting early crypto disks... cswap(starting) encrypted(starting)
Enter LUKS passphrase:
key slot 1 unlocked.
Command successful.
done.
Starting remaining crypto disks... cswap(running) encrypted(running)done.
Checking file systems...fsck 1.40-WIP (14-Nov-2006)/dev/md0: clean, 36/24096 files, 35121/96256 blocks (check after next mount)/dev/md5: clean, 40392/1221600 files, 1043914/2441824 blocks/dev/sdd2: clean, 10111/4889248 files, 5934404/9765511 blocks/dev/sdd3: clean, 1778/21987328 files, 35333378/43961872 blocks (check in 5 mounts)/dev/md8: clean, 116771/2747136 files, 909662/5490144 blocks/dev/md3: clean, 101351/2443200 files, 672471/4883712 blocks/dev/md6: clean, 53/1221600 files, 76570/2441824 blocks/dev/md7: clean, 1179413/7323648 files, 5757529/14647200 blocks/dev/md4: clean, 7509/732960 files, 268934/1465856 blocks (check in 3 mounts)/dev/mapper/encrypted: clean, 14607/12222464 files, 13969744/24414646 blocks
done.
Setting kernel variables...done.
Mounting local filesystems...kjournald starting. Commit interval 5 seconds
EXT3 FS on md0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on md5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sdd2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sdd3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on md8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on md3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on md6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on md7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on md4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
done.
Activating swapfile swap...Adding 15631096k swap on /dev/mapper/cswap. Priority:1 extents:1 across:15631096k done.
Detecting hardware...Setting up networking....
Configuring network interfaces...done.
Starting portmap daemon....
sky2 eth1: enabling interface
sky2 eth1: ram buffer 0K
NET: Registered protocol family 10
lo: Disabled Privacy ExtensionsADDRCONF(NETDEV_UP): eth1: link is not ready
Setting sensors limits: done.
Setting console screen modes and fonts.
Setting up ALSA...done.
Recovering schroot sessions: sid32-df306a93-1d63-494d-a726-c924190900c6.
INIT: Entering runlevel: 2
Starting system log daemon....
Starting kernel log daemon....
Starting portmap daemon...Already running..
Starting HP Linux Printing and Imaging System: hpiod hpssdsky2 eth1: Link is up at 1000 Mbps, full duplex, flow control both ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
.
Loading ACPI modules...input: Power Button (FF) as /class/input/input4
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input5
ACPI: Power Button (CM) [PWRB]
.
Starting Advanced Configuration and Power Interface daemon....
Starting BitTorrent tracker: disabled in /etc/default/bittorrent.
Starting Common Unix Printing System: cupsdlp: driver loaded but no devices found
ppdev: user-space parallel port driver
.
Starting system message bus: dbus.
Starting network connection manager: NetworkManager.
Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
Starting network events dispatcher: NetworkManagerDispatcher.
Starting MTA: exim4.
Starting mouse interface server: gpm.
Starting disk temperature monitoring daemon: hddtemp: /dev/sda /dev/sdb /dev/sdc /dev/sdd..
Installing knfsd (copyright (C) 1996 [email protected]).
Exporting directories for NFS kernel daemon....
Starting NFS kernel daemon: nfsdNFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: starting 90-second grace period
mountd.
Starting internet superserver: inetd.
Starting OpenBSD Secure Shell server: sshd.
Starting GNOME Display Manager: gdm.
Starting NFS common utilities: statd idmapd.
Starting DHCP D-Bus daemon: dhcdbd.
Starting Hardware abstraction layer: hald.
Starting MD monitoring service: mdadm --monitor.
Starting anac(h)ronistic cron: anacron.
Starting periodic command scheduler: crond.
Debian GNU/Linux lenny/sid hikaru ttyS0
hikaru login:
===================================================================================
And the diff between the two:
rawserial-master-188e1 renamed from rawserial-master-188e1-agp=off +3 -1
@@ -2,19 +2,22 @@ Press any key to continue. Press any key to continue. Press any key to continue. +Press any key to continue. +Press any key to continue. +Press any key to continue. ^[[H^[[J GNU GRUB version 0.97 (635K lower / 2095680K upper memory) ^[[m^[[4;2H+-------------------------------------------------------------------------+^[[5;2H|^[[5;76H|^[[6;2H|^[[6;76H|^[[7;2H|^[[7;76H|^[[8;2H|^[[8;76H|^[[9;2H|^[[9;76H|^[[10;2H|^[[10;76H|^[[11;2H|^[[11;76H|^[[12;2H|^[[12;76H|^[[13;2H|^[[13;76H|^[[14;2H|^[[14;76H|^[[15;2H|^[[15;76H|^[[16;2H|^[[16;76H|^[[17;2H+-------------------------------------------------------------------------+^[[m Use the ^ and v keys to select which entry is highlighted. Press enter to boot the selected OS, 'e' to edit the - commands before booting, or 'c' for a command-line.^[[5;78H ^[[m^[[7m^[[5;3H Debian GNU/Linux, kernel 2.6.22-rc5-master-188e1f81ba31af1b65a2f3611d> ^[[5;75H^[[m^[[m^[[6;3H Debian GNU/Linux, kernel 2.6.22-rc5-master-188e1f81ba31af1b65a2f3611d> ^[[6;75H^[[m^[[m^[[7;3H Debian GNU/Linux, kernel 2.6.22-rc4-hikaru-amd64 ^[[7;75H^[[m^[[m^[[8;3H Debian GNU/Linux, kernel 2.6.22-rc4-hikaru-amd64 (single-user mode) ^[[8;75H^[[m^[[m^[[9;3H Debian GNU/Linux, kernel 2.6.18-4-amd64 ^[[9;75H^[[m^[[m^[[10;3H Debian GNU/Linux, kernel 2.6.18-4-amd64 (single-user mode) ^[[10;75H^[[m^[[m^[[11;3H ^[[11;75H^[[m^[[m^[[12;3H ^[[12;75H^[[m^[[m^[[13;3H ^[[13;75H^[[m^[[m^[[14;3H ^[[14;75H^[[m^[[m^[[15;3H ^[[15;75H^[[m^[[m^[[16;3H ^[[16;75H^[[m^[[16;78H ^[[5;75H^[[23;4H The highlighted entry will be booted automatically in 5 seconds. ^[[5;75H^[[23;4H The highlighted entry will be booted automatically in 4 seconds. ^[[5;75H^[[23;4H The highlighted entry will be booted automatically in 3 seconds. ^[[5;75H^[[23;4H ^[[5;75H^[[m^[[5;3H Debian GNU/Linux, kernel 2.6.22-rc5-master-188e1f81ba31af1b65a2f3611d> ^[[5;75H^[[m^[[m^[[7m^[[6;3H Debian GNU/Linux, kernel 2.6.22-rc5-master-188e1f81ba31af1b65a2f3611d> ^[[6;75H^[[m^[[m^[[6;3H Debian GNU/Linux, kernel 2.6.22-rc5-master-188e1f81ba31af1b65a2f3611d> ^[[6;75H^[[m^[[m^[[7m^[[5;3H Debian GNU/Linux, kernel 2.6.22-rc5-master-188e1f81ba31af1b65a2f3611d> ^[[5;75H^[[m^[[H^[[J Booting 'Debian GNU/Linux, kernel 2.6.22-rc5-! master-1
88e1f81ba31af1b65a2f3611
+ commands before booting, or 'c' for a command-line.^[[5;78H ^[[m^[[7m^[[5;3H Debian GNU/Linux, kernel 2.6.22-rc5-master-188e1f81ba31af1b65a2f3611d> ^[[5;75H^[[m^[[m^[[6;3H Debian GNU/Linux, kernel 2.6.22-rc5-master-188e1f81ba31af1b65a2f3611d> ^[[6;75H^[[m^[[m^[[7;3H Debian GNU/Linux, kernel 2.6.22-rc4-hikaru-amd64 ^[[7;75H^[[m^[[m^[[8;3H Debian GNU/Linux, kernel 2.6.22-rc4-hikaru-amd64 (single-user mode) ^[[8;75H^[[m^[[m^[[9;3H Debian GNU/Linux, kernel 2.6.18-4-amd64 ^[[9;75H^[[m^[[m^[[10;3H Debian GNU/Linux, kernel 2.6.18-4-amd64 (single-user mode) ^[[10;75H^[[m^[[m^[[11;3H ^[[11;75H^[[m^[[m^[[12;3H ^[[12;75H^[[m^[[m^[[13;3H ^[[13;75H^[[m^[[m^[[14;3H ^[[14;75H^[[m^[[m^[[15;3H ^[[15;75H^[[m^[[m^[[16;3H ^[[16;75H^[[m^[[16;78H ^[[5;75H^[[23;4H The highlighted entry will be booted automatically in 5 seconds. ^[[5;75H^[[23;4H The highlighted entry will be booted automatically in 4 seconds. ^[[5;75H^[[23;4H The highlighted entry will be booted automatically in 3 seconds. ^[[5;75H^[[23;4H The highlighted entry will be booted automatically in 2 seconds. ^[[5;75H^[[23;4H ^[[5;75H^[[m^[[5;3H Debian GNU/Linux, kernel 2.6.22-rc5-master-188e1f81ba31af1b65a2f3611d> ^[[5;75H^[[m^[[m^[[7m^[[6;3H Debian GNU/Linux, kernel 2.6.22-rc5-master-188e1f81ba31af1b65a2f3611d> ^[[6;75H^[[m^[[m^[[6;3H Debian GNU/Linux, kernel 2.6.22-rc5-master-188e1f81ba31af1b65a2f3611d> ^[[6;75H^[[m^[[m^[[7m^[[5;3H Debian GNU/Linux, kernel 2.6.22-rc5-master-188e1f81ba31!
af1b65a2
f3611d> ^[[5;75H^[[m^[[H^[[J Booting 'Debian GNU/Linux, kernel 2.6.22-rc5-master-188e1f81ba31af1b65a2f3611
df4c670b092bbac-amd64'
root (hd0,0)
Filesystem type is ext2fs, partition type 0xfd
kernel /vmlinuz-2.6.22-rc5-master-188e1f81ba31af1b65a2f3611df4c670b092bbac-amd
-64 root=/dev/md2 ro console=tty0 console=ttyS0,38400n8 agp=off
+64 root=/dev/md2 ro console=tty0 console=ttyS0,38400n8
[Linux-bzImage, setup=0x1e00, size=0x17ac68]
initrd /initrd.img-2.6.22-rc5-master-188e1f81ba31af1b65a2f3611df4c670b092bbac- amd64
@@ -22,7 +25,7 @@
savedefault
Linux version 2.6.22-rc5-master-188e1f81ba31af1b65a2f3611df4c670b092bbac-amd64 (carlo@hikaru) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP Sun Jun 17 18:45:05 CEST 2007
-Command line: root=/dev/md2 ro console=tty0 console=ttyS0,38400n8 agp=off
+Command line: root=/dev/md2 ro console=tty0 console=ttyS0,38400n8
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009ec00 (usable)
BIOS-e820: 000000000009ec00 - 00000000000a0000 (reserved)
@@ -88,17 +91,17 @@
SMP: Allowing 4 CPUs, 0 hotplug CPUs
PERCPU: Allocating 37768 bytes of per cpu data
Built 1 zonelists. Total pages: 1025869
-Kernel command line: root=/dev/md2 ro console=tty0 console=ttyS0,38400n8 agp=off
+Kernel command line: root=/dev/md2 ro console=tty0 console=ttyS0,38400n8
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Extended CMOS year: 2000-time.c: Detected 2666.669 MHz processor.+time.c: Detected 2666.666 MHz processor.
Console: colour VGA+ 80x25
Checking aperture...
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
Placing software IO TLB between 0x1059000 - 0x5059000
Memory: 4030964k/6291456k available (2015k kernel code, 162500k reserved, 947k data, 296k init)
-Calibrating delay using timer specific routine.. 5336.89 BogoMIPS (lpj=10673790)
+Calibrating delay using timer specific routine.. 5336.91 BogoMIPS (lpj=10673826)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
@@ -115,12 +118,12 @@
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
Using local APIC timer interrupts.
-result 16666671
+result 16666650
Detected 16.666 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/4 APIC 0x2
Initializing CPU#1
-Calibrating delay using timer specific routine.. 5333.45 BogoMIPS (lpj=10666915)
+Calibrating delay using timer specific routine.. 5333.56 BogoMIPS (lpj=10667122)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L3 cache: 4096K
CPU 1/2 -> Node 0
@@ -132,7 +135,7 @@
SMP alternatives: switching to SMP code
Booting processor 2/4 APIC 0x1
Initializing CPU#2
-Calibrating delay using timer specific routine.. 5333.58 BogoMIPS (lpj=10667172)
+Calibrating delay using timer specific routine.. 5333.39 BogoMIPS (lpj=10666789)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L3 cache: 4096K
CPU 2/1 -> Node 0
@@ -144,7 +147,7 @@
SMP alternatives: switching to SMP code
Booting processor 3/4 APIC 0x3
Initializing CPU#3
-Calibrating delay using timer specific routine.. 5333.36 BogoMIPS (lpj=10666726)
+Calibrating delay using timer specific routine.. 5333.36 BogoMIPS (lpj=10666733)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L3 cache: 4096K
CPU 3/3 -> Node 0
@@ -154,7 +157,7 @@
Intel(R) Core(TM)2 Quad CPU @ 2.66GHz stepping 07
checking TSC synchronization [CPU#0 -> CPU#3]: passed.
Brought up 4 CPUs
-migration_cost=3357
+migration_cost=3360
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
@@ -200,9 +203,9 @@
pnp: 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved
pnp: 00:0a: iomem range 0xfee00000-0xfee00fff could not be reserved
pnp: 00:0d: iomem range 0xe0000000-0xefffffff has been reserved
-Time: tsc clocksource has been installed.
pnp: 00:0e: iomem range 0x0-0x9ffff could not be reserved
pnp: 00:0e: iomem range 0xc0000-0xcffff has been reserved
+Time: tsc clocksource has been installed.
pnp: 00:0e: iomem range 0xe0000-0xfffff could not be reserved
pnp: 00:0e: iomem range 0x100000-0x7fffffff could not be reserved
PCI: Bridge: 0000:00:01.0
@@ -233,7 +236,7 @@
checking if image is initramfs... it is
Freeing initrd memory: 6182k freed
audit: initializing netlink socket (disabled)
-audit(1182191286.492:1): initialized
+audit(1182191783.492:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
io scheduler noop registered
@@ -244,6 +247,7 @@
assign_interrupt_mode Found MSI capability
assign_interrupt_mode Found MSI capability
Real Time Clock Driver v1.12ac
+Linux agpgart interface v0.102 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
@@ -281,49 +285,52 @@
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
-ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 18
-ehci_hcd 0000:00:1a.7: EHCI Host Controller
-ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 3
-ehci_hcd 0000:00:1a.7: debug port 1
-ehci_hcd 0000:00:1a.7: irq 18, io mem 0xfebff400
-ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
-usb usb3: configuration #1 chosen from 1 choice
-hub 3-0:1.0: USB hub found
-hub 3-0:1.0: 4 ports detected
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
uhci_hcd 0000:00:1d.0: UHCI Host Controller
-uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 4
+uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000d800
-usb usb4: configuration #1 chosen from 1 choice
-hub 4-0:1.0: USB hub found
-hub 4-0:1.0: 2 ports detected
+usb usb3: configuration #1 chosen from 1 choice
+hub 3-0:1.0: USB hub found
+hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.1: UHCI Host Controller
-uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 5
+uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000d880
-usb usb5: configuration #1 chosen from 1 choice
-hub 5-0:1.0: USB hub found
-hub 5-0:1.0: 2 ports detected
+usb usb4: configuration #1 chosen from 1 choice
+hub 4-0:1.0: USB hub found
+hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: UHCI Host Controller
-uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 6
+uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000dc00
+usb usb5: configuration #1 chosen from 1 choice
+hub 5-0:1.0: USB hub found
+hub 5-0:1.0: 2 ports detected
+ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 18
+ehci_hcd 0000:00:1a.7: EHCI Host Controller
+ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 6
+usb 4-2: new low speed USB device using uhci_hcd and address 2
+ehci_hcd 0000:00:1a.7: debug port 1
+ehci_hcd 0000:00:1a.7: irq 18, io mem 0xfebff400
+ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
-hub 6-0:1.0: 2 ports detected
+hub 6-0:1.0: 4 ports detected
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 7
-usb 5-2: new low speed USB device using uhci_hcd and address 2
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfebff000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
+usb 4-2: configuration #1 chosen from 1 choice
+usb 4-2: can't set config #1, error -71
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 6 ports detected
+usb 4-2: USB disconnect, address 2
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
-usb 5-2: new low speed USB device using uhci_hcd and address 3
-usb 5-2: configuration #1 chosen from 1 choice
+usb 4-2: new low speed USB device using uhci_hcd and address 3
+usb 4-2: configuration #1 chosen from 1 choice
usbcore: registered new interface driver hiddev
input: Microsoft Microsoft Wireless Intellimouse Explorer® 1.0A as /class/input/input1
input: USB HID v1.10 Mouse [Microsoft Microsoft Wireless Intellimouse Explorer® 1.0A] on usb-0000:00:1d.1-2
@@ -426,16 +433,16 @@
D modules ...
raid5: automatically using best checksumming function: generic_sse
Success: loaded module raid1.
- generic_sse: 9512.000 MB/sec
-raid5: using function: generic_sse (9512.000 MB/sec)
-raid6: int64x1 2501 MB/s -raid6: int64x2 3018 MB/s + generic_sse: 9514.000 MB/sec +raid5: using function: generic_sse (9514.000 MB/sec) +raid6: int64x1 2500 MB/s +raid6: int64x2 3017 MB/s raid6: int64x4 2881 MB/s raid6: int64x8 1921 MB/s -raid6: sse2x1 4208 MB/s -raid6: sse2x2 5243 MB/s -raid6: sse2x4 7870 MB/s -raid6: using algorithm sse2x4 (7870 MB/s) +raid6: sse2x1 4193 MB/s +raid6: sse2x2 4612 MB/s +raid6: sse2x4 7864 MB/s
+raid6: using algorithm sse2x4 (7864 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
@@ -577,10 +584,10 @@
Attempting manual resume
kinit: name_to_dev_t(/dev/md1) = md1(9,1)
kinit: trying to resume from /dev/md1
-kinit: No resume image, doing kjournald starting. Commit interval 5 seconds
-EXT3-fs: mounted filesystem with ordered data mode.
-normal boot...
+kinit: No resume image, doing normal boot...
Done.
+kjournald starting. Commit interval 5 seconds
+EXT3-fs: mounted filesystem with ordered data mode.
Begin: Running /scripts/local-bottom ...
Done.
Done.
@@ -590,138 +597,4 @@
INIT: version 2.86 booting
Starting the hotplug events dispatcher: udevd.
Synthesizing the initial hotplug events...done.
-Waiting for /dev to be fully populated...iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (21-Jan-2007) -iTCO_wdt: Found a ICH8 or ICH8R TCO device (Version=2, TCOBASE=0x0860)
-iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
-ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 17 (level, low) -> IRQ 17
-sky2 0000:02:00.0: v1.14 addr 0xfe9fc000 irq 17 Yukon-EC Ultra (0xb4) rev 2
-input: PC Speaker as /class/input/input2
-sky2 eth0: addr 00:1a:92:3a:4a:c1
-PCI: Enabling device 0000:00:1f.3 (0001 -> 0003)
-ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 18 (level, low) -> IRQ 18
-gameport: EMU10K1 is pci0000:04:02.1/gameport0, io 0xcc00, speed 1041kHz
-ACPI: PCI Interrupt 0000:04:02.0[A] -> GSI 23 (level, low) -> IRQ 23
-input: PS/2 Logitech Mouse as /class/input/input3
-done.
-Setting parameters of disc: (none).
-Checking root file system...fsck 1.40-WIP (14-Nov-2006)
-/dev/md2: clean, 14667/488640 files, 100111/975904 blocks
-done.-EXT3 FS on md2, internal journal
-Setting the system clock..
-Cleaning up ifupdown....
-Loading kernel modules...loop: module loaded
-coretemp coretemp.0: Using undocumented features, absolute temperature might be wrong!
-coretemp coretemp.1: Using undocumented features, absolute temperature might be wrong!
-coretemp coretemp.2: Using undocumented features, absolute temperature might be wrong!
-coretemp coretemp.3: Using undocumented features, absolute temperature might be wrong!
-done.
-Loading device-mapper supportdevice-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: [email protected] -.
-Generating udev events for MD arrays...done.
-Starting early crypto disks... cswap(starting) encrypted(starting)
-Enter LUKS passphrase:
-key slot 1 unlocked.
-Command successful.
-done.
-Starting remaining crypto disks... cswap(running) encrypted(running)done.
-Checking file systems...fsck 1.40-WIP (14-Nov-2006)
-/dev/md0: clean, 36/24096 files, 35121/96256 blocks (check after next mount)
-/dev/md5: clean, 40392/1221600 files, 1043914/2441824 blocks
-/dev/sdd2: clean, 10111/4889248 files, 5934404/9765511 blocks
-/dev/sdd3: clean, 1778/21987328 files, 35333378/43961872 blocks (check in 5 mounts)
-/dev/md8: clean, 116771/2747136 files, 909662/5490144 blocks
-/dev/md3: clean, 101351/2443200 files, 672471/4883712 blocks
-/dev/md6: clean, 53/1221600 files, 76570/2441824 blocks
-/dev/md7: clean, 1179413/7323648 files, 5757529/14647200 blocks
-/dev/md4: clean, 7509/732960 files, 268934/1465856 blocks (check in 3 mounts)
-/dev/mapper/encrypted: clean, 14607/12222464 files, 13969744/24414646 blocks
-done.
-Setting kernel variables...done.
-Mounting local filesystems...kjournald starting. Commit interval 5 seconds-EXT3 FS on md0, internal journal
-EXT3-fs: mounted filesystem with ordered data mode.
-kjournald starting. Commit interval 5 seconds-EXT3 FS on md5, internal journal
-EXT3-fs: mounted filesystem with ordered data mode.
-kjournald starting. Commit interval 5 seconds-EXT3 FS on sdd2, internal journal
-EXT3-fs: mounted filesystem with ordered data mode.
-kjournald starting. Commit interval 5 seconds-EXT3 FS on sdd3, internal journal
-EXT3-fs: mounted filesystem with ordered data mode.
-kjournald starting. Commit interval 5 seconds-EXT3 FS on md8, internal journal
-EXT3-fs: mounted filesystem with ordered data mode.
-kjournald starting. Commit interval 5 seconds-EXT3 FS on md3, internal journal
-EXT3-fs: mounted filesystem with ordered data mode.
-kjournald starting. Commit interval 5 seconds-EXT3 FS on md6, internal journal
-EXT3-fs: mounted filesystem with ordered data mode.
-kjournald starting. Commit interval 5 seconds-EXT3 FS on md7, internal journal
-EXT3-fs: mounted filesystem with ordered data mode.
-kjournald starting. Commit interval 5 seconds-EXT3 FS on md4, internal journal
-EXT3-fs: mounted filesystem with ordered data mode.
-kjournald starting. Commit interval 5 seconds-EXT3 FS on dm-1, internal journal
-EXT3-fs: mounted filesystem with ordered data mode.
-done.
-Activating swapfile swap...Adding 15631096k swap on /dev/mapper/cswap. Priority:1 extents:1 across:15631096k -done.
-Detecting hardware...Setting up networking....
-Configuring network interfaces...done.
-Starting portmap daemon....
-sky2 eth1: enabling interface
-sky2 eth1: ram buffer 0K
-NET: Registered protocol family 10
-lo: Disabled Privacy Extensions
-ADDRCONF(NETDEV_UP): eth1: link is not ready
-Setting sensors limits: done.
-Setting console screen modes and fonts.
-Setting up ALSA...done.
-Recovering schroot sessions: sid32-df306a93-1d63-494d-a726-c924190900c6.
-INIT: Entering runlevel: 2
-Starting system log daemon....
-Starting kernel log daemon....
-Starting portmap daemon...Already running..
-Starting HP Linux Printing and Imaging System: hpiod hpssdsky2 eth1: Link is up at 1000 Mbps, full duplex, flow control both -ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
-.
-Loading ACPI modules...input: Power Button (FF) as /class/input/input4
-ACPI: Power Button (FF) [PWRF]
-input: Power Button (CM) as /class/input/input5
-ACPI: Power Button (CM) [PWRB]
-.
-Starting Advanced Configuration and Power Interface daemon....
-Starting BitTorrent tracker: disabled in /etc/default/bittorrent.
-Starting Common Unix Printing System: cupsdlp: driver loaded but no devices found
-ppdev: user-space parallel port driver
-.
-Starting system message bus: dbus.
-Starting network connection manager: NetworkManager.
-Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
-Starting network events dispatcher: NetworkManagerDispatcher.
-Starting MTA: exim4.
-Starting mouse interface server: gpm.
-Starting disk temperature monitoring daemon: hddtemp: /dev/sda /dev/sdb /dev/sdc /dev/sdd..
-Installing knfsd (copyright (C) 1996 [email protected]).
-Exporting directories for NFS kernel daemon....
-Starting NFS kernel daemon: nfsdNFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory -NFSD: starting 90-second grace period
- mountd.
-Starting internet superserver: inetd.
-Starting OpenBSD Secure Shell server: sshd.
-Starting GNOME Display Manager: gdm.
-Starting NFS common utilities: statd idmapd.
-Starting DHCP D-Bus daemon: dhcdbd.
-Starting Hardware abstraction layer: hald.
-Starting MD monitoring service: mdadm --monitor.
-Starting anac(h)ronistic cron: anacron.
-Starting periodic command scheduler: crond.
-
-Debian GNU/Linux lenny/sid hikaru ttyS0
-
-hikaru login:
+Waiting for /dev to be fully populated...agpgart: Detected an Intel 965G Chipset.
As you can see, lots and lots of things are being done between
Linux agpgart interface v0.102 (c) Dave Jones
and
agpgart: Detected an Intel 965G Chipset.
Signature · 1 line
Carlo Wood <[email protected]>
Re: [AGPGART] intel_agp: use table for device probe
In reply to Wang ZhenyuQuoted 2 lines · Wang Zhenyu
Carlo, I've just built latest kernel git tree on a Dell 965G box and have a NV card plugged-in. It boots fine.
It would be nice if you could test it with the exact same hardware ... I am pretty sure it should be reproducable then *cough*
Quoted 8 lines
Linux agpgart interface v0.102 (c) Dave Jones
agpgart: Detected an Intel 965G Chipset.
agpgart: AGP aperture is 256M @0x0I don't know why it hangs your machine when loading this module, it should just not bother anything. But from your last "modprobe: ..." line, it seems there's really badness somewhere, do you have serial console to see more in the message?
The reason I react a bit late to your post is because in the meantime I set up a serial console and figured out how to boot that way... and captured the boot messages.
I will add that to one of the other posts, because as a result of what they posted there I added agp=off - and that (indeed) makes it possible for me to boot. Please see my next post thus.
Signature · 1 line
Carlo Wood <[email protected]>