debian 40r installation issue on IA 64
I have been trying to install debian 40r0 on hp longs peak itanium server. The installation hangs trying to configure net....
EFI Time Services Driver v0.4
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
00:04: ttyS0 at MMIO 0xff5e0000 (irq = 49) is a 16550A 00:05: ttyS1 at MMIO 0xff5e2000 (irq = 50) is a 16550A GSI 82 (level, low) -> CPU 1 (0x0100) vector 51
ACPI: PCI Interrupt 0000:e0:01.0[A] -> GSI 82 (level, low) -> IRQ 51
0000:e0:01.0: ttyS2 at MMIO 0xf8031000 (irq = 51) is a 16550A
ACPI: PCI Interrupt 0000:e0:01.1[A] -> GSI 82 (level, low) -> IRQ 51
0000:e0:01.1: ttyS3 at MMIO 0xf8030000 (irq = 51) is a 16550A
Couldn't register serial port 0000:e0:01.1: -28 RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize
mice: PS/2 mouse device common for all mice TCP bic registered
NET: Re
Quoted 3 lines · Kallol Biswas
I have been trying to install debian 40r0 on hp longs peak itanium server. The installation hangs trying to configure net....
I copied the debian-ia64 list, which is probably a better place to start.
The HP management processor contains a virtual UART that is implemented partly in hardware and partly in firmware. There have been a number of issues related to the fact that it is not a real 16550 UART.
Here's a summary of the issues I know about. My guess is that you're seeing the first one, so I'd start by checking your MP firmware revision.
* serial console device lockup
- system responds via network
- no input or output via serial console device
- occurs when application opens device while transmit buffer contains polled-mode kernel output, typically during boot
- INIT dump shows CPUs in idle loop
- after system reset, MP event log shows "BOOT_PLAT_CONSOLE_DEV_FAILED" or similar event
- hang is resolved only by MP reset; system reset is not sufficient
- resolved in MP firmware E.03.29 or later (rx16x0, rx26x0, rx4640, rx5670)
- resolved in MP firmware F.01.39 or later (rx3600, rx6600)
* serial console driver deadlock
- system completely unresponsive to all devices
- INIT dump shows one or more CPUs in ia64_spinlock_contention, waiting for a ttyS UART lock (lock ptr in r31)
* serial device out of sync with driver
- system responds via network
- serial output stops
- sending serial input generates an interrupt that causes up to 16 more characters of output
- re-opening the device fixes the problem
* serial device drops interrupt
- system responds via network
- serial output stops
- sending serial input generates an interrupt that resolves the problem
Quoted 14 lines
EFI Time Services Driver v0.4
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled 00:04: ttyS0 at MMIO0xff5e0000(irq = 49) is a 16550A 00:05: ttyS1 at MMIO0xff5e2000(irq = 50) is a 16550A
GSI 82 (level, low) -> CPU 1 (0x0100) vector 51
ACPI: PCI Interrupt 0000:e0:01.0[A] -> GSI 82 (level, low) -> IRQ 51 0000:e0:01.0: ttyS2 at MMIO0xf8031000(irq = 51) is a 16550A
ACPI: PCI Interrupt 0000:e0:01.1[A] -> GSI 82 (level, low) -> IRQ 51 0000:e0:01.1: ttyS3 at MMIO0xf8030000(irq = 51) is a 16550A Couldn't register serial port 0000:e0:01.1: -28
RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Re
Quoted 4 lines
Quoted 4 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
"Bjorn" = Bjorn Helgaas <[email protected]> writes:
I have been trying to install debian 40r0 on hp longs peak itanium server. The installation hangs trying to configure net....
I ran into this yesterday. Upgrading the MP firmware to 3.30 fixed the problem...
Signature · 1 line
Martin K. Petersen Oracle Linux Engineering