2.6.23-rc1: USB hard disk broken
Hi,
I just tried 2.6.23-rc1 and shortly after the boot my external USB hard disk went mad.
I all started with these kernel messages:
kern.info: usb 1-6: USB disconnect, address 5
kern.info: sd 4:0:0:0: [sdb] Result: hostbyte=0x07 driverbyte=0x00 kern.warn: end_request: I/O error, dev sdb, sector 680000479 kern.alert: I/O error in filesystem ("dm-2") meta-data dev dm-2 block 0x6c7fa20 ("xfs_trans_read_buf") error 5 buf count 8192
The full kernel log can be found here:
And the config:
Needless to say that it all worked fine with 2.6.22.
Regards,
Tino
Am Mittwoch 25 Juli 2007 schrieb Tino Keitel:
Quoted 15 lines
Hi,
I just tried 2.6.23-rc1 and shortly after the boot my external USB hard disk went mad.
I all started with these kernel messages:
kern.info: usb 1-6: USB disconnect, address 5
kern.info: sd 4:0:0:0: [sdb] Result: hostbyte=0x07 driverbyte=0x00 kern.warn:end_request: I/O error, dev sdb, sector 680000479 kern.alert: I/O error in filesystem ("dm-2") meta-data dev dm-2 block0x6c7fa20("xfs_trans_read_buf") error 5 buf count 8192The full kernel log can be found here:
Quoted 7 lines
And the config:
Needless to say that it all worked fine with 2.6.22.
Please recompile with CONFIG_USB_DEBUG set.
Regards
Oliver
Quoted 5 lines · Oliver Neukum
Am Mittwoch 25 Juli 2007 schrieb Tino Keitel:
Quoted 4 lines
Hi,
I just tried 2.6.23-rc1 and shortly after the boot my external USB hard disk went mad.
[...]
Quoted 4 lines
Please recompile with
CONFIG_USB_DEBUGset.Regards
Oliver
I tried, but it didn't happen again.
Regards,
Tino
Am Mittwoch 25 Juli 2007 schrieb Tino Keitel:
Quoted 7 lines · Oliver Neukum
Quoted 5 lines
Am Mittwoch 25 Juli 2007 schrieb Tino Keitel:
Quoted 4 lines
Hi,
I just tried 2.6.23-rc1 and shortly after the boot my external USB hard disk went mad.
Quoted 8 lines
[...]
Quoted 4 lines
Please recompile with
CONFIG_USB_DEBUGset.Regards
OliverI tried, but it didn't happen again.
Did you try with the old kernel again? This bug may be related to timing.
Regards
Oliver
Quoted 10 lines · Oliver Neukum
Am Mittwoch 25 Juli 2007 schrieb Tino Keitel:
Quoted 9 lines · Oliver Neukum
Quoted 5 lines
Am Mittwoch 25 Juli 2007 schrieb Tino Keitel:
Quoted 4 lines
Hi,
I just tried 2.6.23-rc1 and shortly after the boot my external USB hard disk went mad.
[...]
Quoted 8 lines
Quoted 6 lines
Quoted 4 lines
Please recompile with
CONFIG_USB_DEBUGset.Regards
OliverI tried, but it didn't happen again.
Did you try with the old kernel again? This bug may be related to timing.
I tried again -rc1 without USB_DEBUG, and was able to reproduce the bug 2 times. At the second time, the kernel log shows this:
2007-08-05_10:30:27.75572 kern.err: ehci_hcd 0000:00:1d.7: dev 6 ep1in scatterli
st error 0/-121
2007-08-05_10:30:27.86576 kern.info: usb 1-6: reset high speed USB device using ehci_hcd and address 5 2007-08-05_10:30:55.95293 kern.info: usb 1-6: USB disconnect, address 5 2007-08-05_10:30:55.95300 kern.err: ehci_hcd 0000:00:1d.7: dev 6 ep1in scatterlist error -108/-108 2007-08-05_10:30:55.95310 kern.info: sd 4:0:0:0: [sdb] Result: hostbyte=0x07 driverbyte=0x00 2007-08-05_10:30:55.95314 kern.warn: end_request: I/O error, dev sdb, sector 594818327 2007-08-05_10:30:55.95321 kern.info: sd 4:0:0:0: [sdb] Result: hostbyte=0x07 driverbyte=0x00 2007-08-05_10:30:55.95325 kern.warn: end_request: I/O error, dev sdb, sector 594818567 2007-08-05_10:30:55.95331 kern.info: sd 4:0:0:0: [sdb] Result: hostbyte=0x07 driverbyte=0x00 2007-08-05_10:30:55.95335 kern.warn: end_request: I/O error, dev sdb, sector 594818583 2007-08-05_10:30:55.95342 kern.info: sd 4:0:0:0: [sdb] Result: hostbyte=0x07 driverbyte=0x00 2007-08-05_10:30:55.95352 kern.warn: end_request: I/O error, dev sdb, sector 594818823 2007-08-05_10:30:55.95356 kern.info: sd 4:0:0:0: [sdb] Result: hostbyte=0x07 driverbyte=0x00 2007-08-05_10:30:55.95360 kern.warn: end_request: I/O error, dev sdb, sector 594818327 2007-08-05_10:30:55.95455 kern.info: sd 4:0:0:0: [sdb] Result: hostbyte=0x07 driverbyte=0x00 2007-08-05_10:30:55.95461 kern.warn: end_request: I/O error, dev sdb, sector 594818327 2007-08-05_10:30:55.96972 kern.err: scsi 4:0:0:0: rejecting I/O to dead device 2007-08-05_10:30:55.96977 kern.err: scsi 4:0:0:0: rejecting I/O to dead device
The "scatterlist" line wasn't there in the other cases. I'll try again with the latest git.
Regards,
Tino
Quoted 16 lines · Tino Keitel
Quoted 15 lines · Oliver Neukum
Am Mittwoch 25 Juli 2007 schrieb Tino Keitel:
Quoted 14 lines · Oliver Neukum
Quoted 5 lines
Am Mittwoch 25 Juli 2007 schrieb Tino Keitel:
Quoted 4 lines
Hi,
I just tried 2.6.23-rc1 and shortly after the boot my external USB hard disk went mad.
[...]
Quoted 4 lines
Please recompile with
CONFIG_USB_DEBUGset.Regards
Oliver
Quoted 6 lines
Quoted 3 lines
Quoted 1 line
I tried, but it didn't happen again.
Did you try with the old kernel again? This bug may be related to timing.
I tried again -rc1 without
USB_DEBUG, and was able to reproduce the bug 2 times. At the second time, the kernel log shows this:
Now I tried current git d4ac2477fad0f2680e84ec12e387ce67682c5c13 and I can still reproduce it.
Regards,
Tino
Am Sonntag 05 August 2007 schrieb Tino Keitel:
Quoted 20 lines · Oliver Neukum
Quoted 10 lines
Am Mittwoch 25 Juli 2007 schrieb Tino Keitel:
Quoted 9 lines · Oliver Neukum
Quoted 5 lines
Am Mittwoch 25 Juli 2007 schrieb Tino Keitel:
Quoted 4 lines
Hi,
I just tried 2.6.23-rc1 and shortly after the boot my external USB hard disk went mad.
[...]
Quoted 8 lines
Quoted 6 lines
Quoted 4 lines
Please recompile with
CONFIG_USB_DEBUGset.Regards
OliverI tried, but it didn't happen again.
Did you try with the old kernel again? This bug may be related to timing.
Quoted 8 lines
I tried again -rc1 without
USB_DEBUG, and was able to reproduce the bug 2 times. At the second time, the kernel log shows this:2007-08-05_10:30:27.75572 kern.err:
ehci_hcd0000:00:1d.7: dev 6 ep1in scatterli
st error 0/-121
2007-08-05_10:30:27.86576 kern.info: usb 1-6: reset high speed USB device usingehci_hcdand address 5 2007-08-05_10:30:55.95293 kern.info: usb 1-6: USB disconnect, address 5 2007-08-05_10:30:55.95300 kern.err:ehci_hcd0000:00:1d.7: dev 6 ep1in scatterlist error -108/-108
David, does this error say anything to you?
Regards
Oliver
Quoted 3 lines · Oliver Neukum
Quoted 3 lines
2007-08-05_10:30:27.75572 kern.err:
ehci_hcd 0000:00:1d.7: dev 6 ep1in scatterlist error 0/-121
That's rather strange since it means a *success* (urb->status 0) was reported after a short read (scatterlist status -120, -EREMOTEIO).
The hardware should have stopped queue processing after the short read, because of how qtd->hw_alt_next gets set up ... at least, that's how I remember it, these many years after writing that code.
It might be that because of the issue noted below, it was wrongly restarted by the software.
Quoted 4 lines
Quoted 4 lines
2007-08-05_10:30:27.86576 kern.info: usb 1-6: reset high speed USB device using
ehci_hcdand address 5 2007-08-05_10:30:55.95293 kern.info: usb 1-6: USB disconnect, address 5 2007-08-05_10:30:55.95300 kern.err:ehci_hcd 0000:00:1d.7: dev 6 ep1in scatterlist error -108/-108
That one just means nobody updated that test to recognize that the -ESHUTDOWN (-108) triggered after disconnect is a "clean" failure like the ones triggered by unlinking.
However it also indicates that something changed in the unlink code paths, since I see the *expected* code (-ECONNRESET) is no longer being set by usbcore during unlinks ... it's not quite clear to me what else that change will have broken. Including whether that might not explain how the hardware queue got wrongly restarted after the short read above.
- Dave
Quoted 1 line
David, does this error say anything to you?
Quoted 22 lines · Oliver Neukum
Am Sonntag 05 August 2007 schrieb Tino Keitel:
Quoted 12 lines · Oliver Neukum
Quoted 11 lines
Am Mittwoch 25 Juli 2007 schrieb Tino Keitel:
Quoted 10 lines · Oliver Neukum
Quoted 5 lines
Am Mittwoch 25 Juli 2007 schrieb Tino Keitel:
Quoted 4 lines
Hi,
I just tried 2.6.23-rc1 and shortly after the boot my external USB hard disk went mad.
[...]
Quoted 2 lines
Please recompile with
CONFIG_USB_DEBUGset.Quoted 8 lines
I tried again -rc1 without
USB_DEBUG, and was able to reproduce the bug 2 times. At the second time, the kernel log shows this:2007-08-05_10:30:27.75572 kern.err:
ehci_hcd0000:00:1d.7: dev 6 ep1in scatterli
st error 0/-121
2007-08-05_10:30:27.86576 kern.info: usb 1-6: reset high speed USB device usingehci_hcdand address 5 2007-08-05_10:30:55.95293 kern.info: usb 1-6: USB disconnect, address 5 2007-08-05_10:30:55.95300 kern.err:ehci_hcd0000:00:1d.7: dev 6 ep1in scatterlist error -108/-108
Quoted 4 lines
David, does this error say anything to you?
Regards
Oliver
Hi,
I just completed a git bisect, and commit 8dfe4b14869fd185ca25ee88b02ada58a3005eaf was the commit that introduced this problem. This is "usb-storage: implement autosuspend". I don't think there have been many changes in drivers/usb since I last verified this problem, so I'm pretty sure this is still happening in the latest kernel.
The first thing I am going to do is pull the latest sources, attempt to revert this patch, and see whether the kernel compiles and works properly with my USB hard drive. Please let me know of anything I can do to help.
Dan
Quoted 37 lines · Dan Zwell
Quoted 22 lines · Oliver Neukum
Am Sonntag 05 August 2007 schrieb Tino Keitel:
Quoted 12 lines · Oliver Neukum
Quoted 11 lines
Am Mittwoch 25 Juli 2007 schrieb Tino Keitel:
Quoted 10 lines · Oliver Neukum
Quoted 5 lines
Am Mittwoch 25 Juli 2007 schrieb Tino Keitel:
Quoted 4 lines
Hi,
I just tried 2.6.23-rc1 and shortly after the boot my external USB hard disk went mad.
[...]
Quoted 2 lines
Please recompile with
CONFIG_USB_DEBUGset.Quoted 8 lines
I tried again -rc1 without
USB_DEBUG, and was able to reproduce the bug 2 times. At the second time, the kernel log shows this:2007-08-05_10:30:27.75572 kern.err:
ehci_hcd0000:00:1d.7: dev 6 ep1in scatterli
st error 0/-121
2007-08-05_10:30:27.86576 kern.info: usb 1-6: reset high speed USB device usingehci_hcdand address 5 2007-08-05_10:30:55.95293 kern.info: usb 1-6: USB disconnect, address 5 2007-08-05_10:30:55.95300 kern.err:ehci_hcd0000:00:1d.7: dev 6 ep1in scatterlist error -108/-108Quoted 4 lines
David, does this error say anything to you?
Regards
OliverHi,
I just completed a git bisect, and commit
8dfe4b14869fd185ca25ee88b02ada58a3005eafwas the commit that introduced this problem. This is "usb-storage: implement autosuspend". I don't think there have been many changes indrivers/usbsince I last verified this problem, so I'm pretty sure this is still happening in the latest kernel.
Quoted 4 lines
The first thing I am going to do is pull the latest sources, attempt to revert this patch, and see whether the kernel compiles and works properly with my USB hard drive. Please let me know of anything I can do to help.
What makes you think the problem you see is the same as the one described by Tino? Do you get the "scatterlist error 0/-121" line in your log?
Please provide a dmesg log showing your problem with CONFIG_USB_DEBUG enabled.
Alan Stern
On Thu, Aug 09, 2007 at 16:00:13 -0400, Alan Stern wrote:
[...]
Quoted 6 lines
What makes you think the problem you see is the same as the one described by Tino? Do you get the "scatterlist error 0/-121" line in your log?
Please provide a dmesg log showing your problem with
CONFIG_USB_DEBUGenabled.
I'll try to reproduce the problem with the commit reverted, but not before Sunday evening.
Regards,
Tino
Quoted 30 lines · Alan Stern
Quoted 28 lines · Dan Zwell
Quoted 21 lines · Oliver Neukum
Am Sonntag 05 August 2007 schrieb Tino Keitel:
Quoted 12 lines · Oliver Neukum
Quoted 11 lines
Am Mittwoch 25 Juli 2007 schrieb Tino Keitel:
Quoted 10 lines · Oliver Neukum
Quoted 5 lines
Am Mittwoch 25 Juli 2007 schrieb Tino Keitel:
Quoted 4 lines
Hi,
I just tried 2.6.23-rc1 and shortly after the boot my external USB hard disk went mad.
[...]
Quoted 2 lines
Please recompile with
CONFIG_USB_DEBUGset.Quoted 8 lines
I tried again -rc1 without
USB_DEBUG, and was able to reproduce the bug 2 times. At the second time, the kernel log shows this:2007-08-05_10:30:27.75572 kern.err:
ehci_hcd0000:00:1d.7: dev 6 ep1in scatterli
st error 0/-121
2007-08-05_10:30:27.86576 kern.info: usb 1-6: reset high speed USB device usingehci_hcdand address 5 2007-08-05_10:30:55.95293 kern.info: usb 1-6: USB disconnect, address 5 2007-08-05_10:30:55.95300 kern.err:ehci_hcd0000:00:1d.7: dev 6 ep1in scatterlist error -108/-108Quoted 4 lines
David, does this error say anything to you?
Regards
OliverHi,
Quoted 9 lines
Quoted 2 lines
I just completed a git bisect, and commit
8dfe4b14869fd185ca25ee88b02ada58a3005eafwas the commit that introduced this problem. This is "usb-storage: implement autosuspend". I don't think there have been many changes indrivers/usbsince I last verified this problem, so I'm pretty sure this is still happening in the latest kernel.What makes you think the problem you see is the same as the one described by Tino? Do you get the "scatterlist error 0/-121" line in your log?
Please provide a dmesg log showing your problem with
CONFIG_USB_DEBUGenabled.Alan Stern
You're right, it probably isn't the same error, unfortunately. I jumped to conclusions when I read Tino's description of the problem, "my external USB hard disk went mad", which is a very good description of what is happening to me. When any attempt is made to access the USB disk, it (logically) disconnects and reconnects. When using hald's automounting facilities, this leads to (endlessly repeated) madness.
I have attached my dmesg output (and a sanitized version that should contain all the important information, but is easier to read). It looks like the drive is auto suspended, but the resume process fails. Then the process is repeated.
[ 126.512815] usb 1-1: usb auto-resume [ 126.543447] uhci_hcd 0000:00:1f.2: port 1 portsc 00a5,01 [ 126.559426] usb 1-1: finish resume [ 126.561435] usb 1-1: gone after usb resume? status -19 [ 126.561445] usb 1-1: can't resume, status -19 [ 126.561451] hub 1-0:1.0: logical disconnect on port 1 [ 126.562486] sd 5:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OK
Relevant info:
-obviously, I'm using uhci
-the drive is SATA, connected to USB with a SATA/IDE to USB adapter -this problem does not occur with a USB flash drive -reverting the commit that introduced auto-suspend prevents this error.
Thanks,
Dan
Quoted 23 lines · Dan Zwell
Quoted 10 lines
What makes you think the problem you see is the same as the one described by Tino? Do you get the "scatterlist error 0/-121" line in your log?
Please provide a dmesg log showing your problem with
CONFIG_USB_DEBUGenabled.Alan Stern
You're right, it probably isn't the same error, unfortunately. I jumped to conclusions when I read Tino's description of the problem, "my external USB hard disk went mad", which is a very good description of what is happening to me. When any attempt is made to access the USB disk, it (logically) disconnects and reconnects. When using hald's automounting facilities, this leads to (endlessly repeated) madness.
I have attached my dmesg output (and a sanitized version that should contain all the important information, but is easier to read). It looks like the drive is auto suspended, but the resume process fails. Then the process is repeated.
Quoted 8 lines
[ 126.512815] usb 1-1: usb auto-resume [ 126.543447] uhci_hcd 0000:00:1f.2: port 1 portsc 00a5,01 [ 126.559426] usb 1-1: finish resume [ 126.561435] usb 1-1: gone after usb resume? status -19 [ 126.561445] usb 1-1: can't resume, status -19 [ 126.561451] hub 1-0:1.0: logical disconnect on port 1 [ 126.562486] sd 5:0:0:0: [sdb] Result: hostbyte=DID_ERRORdriverbyte=DRIVER_OK,SUGGEST_OK
This suggests a bug in the device's firmware, probably it sends a 1-byte Device-Status reply instead of a 2-byte reply as required by the USB spec. You could find out for certain by using usbmon.
But if that is indeed the problem, the patch below should help. I've seen it before; perhaps we should adopt this workaround permanently.
Review
Quoted 5 lines
Relevant info:
(quoted diff) +0
-4-obviously, I'm using uhci -the drive is SATA, connected to USB with a SATA/IDE to USB adapter -this problem does not occur with a USB flash drive -reverting the commit that introduced auto-suspend prevents this error.
If necessary you could disable autosuspend for your drive. But first test this patch.
Alan Stern
drivers/usb/core/hub.c +2 -1
@@ -1644,9 +1644,10 @@ static int finish_port_resume(struct usb* and device drivers will know about any resume quirks. */ if (status ==0 ) { + devstatus =0 ; status =usb_get_status (udev,USB_RECIP_DEVICE ,0 , &devstatus);if (status >=0 ) - status = (status ==2 ?0 : -ENODEV ); + status = (status >0 ?0 : -ENODEV ); }if (status) {
Quoted 32 lines · Alan Stern
Quoted 7 lines
[ 126.512815] usb 1-1: usb auto-resume [ 126.543447] uhci_hcd 0000:00:1f.2: port 1 portsc 00a5,01 [ 126.559426] usb 1-1: finish resume [ 126.561435] usb 1-1: gone after usb resume? status -19 [ 126.561445] usb 1-1: can't resume, status -19 [ 126.561451] hub 1-0:1.0: logical disconnect on port 1 [ 126.562486] sd 5:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OKThis suggests a bug in the device's firmware, probably it sends a 1-byte Device-Status reply instead of a 2-byte reply as required by the USB spec. You could find out for certain by using usbmon.
But if that is indeed the problem, the patch below should help. I've seen it before; perhaps we should adopt this workaround permanently.
Review
Quoted 5 lines
Relevant info:
(quoted diff) +0
-4-obviously, I'm using uhci -the drive is SATA, connected to USB with a SATA/IDE to USB adapter -this problem does not occur with a USB flash drive -reverting the commit that introduced auto-suspend prevents this error.If necessary you could disable autosuspend for your drive. But first test this patch.
Alan Stern
Index:
2.6.23-rc1/drivers/usb/core/hub.c
===================================================================drivers/usb/core/hub.c +0
-0@@ -1644,9 +1644,10 @@ static int finish_port_resume(struct usb* and device drivers will know about any resume quirks.
drivers/usb/core/hub.c static int finish_port_resume(struct usb · line 1653
Quoted 10 lines
drivers/usb/core/hub.c +2
-1*/ if (status ==0 ) { + devstatus =0 ; status =usb_get_status (udev,USB_RECIP_DEVICE ,0 , &devstatus);if (status >=0 ) - status = (status ==2 ?0 : -ENODEV ); + status = (status >0 ?0 : -ENODEV ); }if (status) {
Alan,
Yes, that patch worked, and dmesg now shows the device auto-suspending and resuming every few seconds. Thanks a lot. I hope you do merge this patch or a workaround like it.
Dan
Quoted 5 lines · Dan Zwell
Alan,
Yes, that patch worked, and dmesg now shows the device auto-suspending and resuming every few seconds. Thanks a lot. I hope you do merge this patch or a workaround like it.
I will submit it; we'll see whether anyone objects.
By the way, you can change the constant autosuspend and autoresume behavior easily enough. All you have to do is:
echo N >/sys/bus/usb/devices/.../power/autosuspend
where "..." is the path for the disk's USB device and N is the number of seconds the disk should be idle before it gets autosuspended. If you use -1 for N then the disk will never autosuspend.
Alan Stern
Re: 2.6.23-rc1: USB hard disk broken (REGRESSION)
In reply to Dan ZwellQuoted 46 lines · Dan Zwell
Quoted 32 lines · Alan Stern
Quoted 7 lines
[ 126.512815] usb 1-1: usb auto-resume [ 126.543447] uhci_hcd 0000:00:1f.2: port 1 portsc 00a5,01 [ 126.559426] usb 1-1: finish resume [ 126.561435] usb 1-1: gone after usb resume? status -19 [ 126.561445] usb 1-1: can't resume, status -19 [ 126.561451] hub 1-0:1.0: logical disconnect on port 1 [ 126.562486] sd 5:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OKThis suggests a bug in the device's firmware, probably it sends a 1-byte Device-Status reply instead of a 2-byte reply as required by the USB spec. You could find out for certain by using usbmon.
But if that is indeed the problem, the patch below should help. I've seen it before; perhaps we should adopt this workaround permanently.
Review
Quoted 5 lines
Relevant info:
(quoted diff) +0
-4-obviously, I'm using uhci -the drive is SATA, connected to USB with a SATA/IDE to USB adapter -this problem does not occur with a USB flash drive -reverting the commit that introduced auto-suspend prevents this error.If necessary you could disable autosuspend for your drive. But first test this patch.
Alan Stern
Index:
2.6.23-rc1/drivers/usb/core/hub.c
===================================================================drivers/usb/core/hub.c +0
-0@@ -1644,9 +1644,10 @@ static int finish_port_resume(struct usb* and device drivers will know about any resume quirks. drivers/usb/core/hub.c static int finish_port_resume(struct usb · line 1653
Quoted 10 lines
drivers/usb/core/hub.c +2
-1*/ if (status ==0 ) { + devstatus =0 ; status =usb_get_status (udev,USB_RECIP_DEVICE ,0 , &devstatus);if (status >=0 ) - status = (status ==2 ?0 : -ENODEV ); + status = (status >0 ?0 : -ENODEV ); }if (status) {Alan,
Quoted 3 lines
Yes, that patch worked, and dmesg now shows the device auto-suspending and resuming every few seconds. Thanks a lot. I hope you do merge this patch or a workaround like it.
Dan
The same bug kills my Sandisk Cruzer Micro USB pen drives.
I plug them in, they work briefly, then the light goes out (abnormal), and 30-second timeout/reset is needed for each subsequent access. Ugh.
They work fine in 2.6.22. I'll try the above patch here now and see if it fixes this regression.
Re: 2.6.23-rc1: USB hard disk broken (REGRESSION)
Quoted 49 lines · Mark Lord
Quoted 48 lines · Dan Zwell
Quoted 32 lines · Alan Stern
Quoted 7 lines
[ 126.512815] usb 1-1: usb auto-resume [ 126.543447] uhci_hcd 0000:00:1f.2: port 1 portsc 00a5,01 [ 126.559426] usb 1-1: finish resume [ 126.561435] usb 1-1: gone after usb resume? status -19 [ 126.561445] usb 1-1: can't resume, status -19 [ 126.561451] hub 1-0:1.0: logical disconnect on port 1 [ 126.562486] sd 5:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK,SUGGEST_OKThis suggests a bug in the device's firmware, probably it sends a 1-byte Device-Status reply instead of a 2-byte reply as required by the USB spec. You could find out for certain by using usbmon.
But if that is indeed the problem, the patch below should help. I've seen it before; perhaps we should adopt this workaround permanently.
Review
Quoted 5 lines
Relevant info:
(quoted diff) +0
-4-obviously, I'm using uhci -the drive is SATA, connected to USB with a SATA/IDE to USB adapter -this problem does not occur with a USB flash drive -reverting the commit that introduced auto-suspend prevents this error.If necessary you could disable autosuspend for your drive. But first test this patch.
Alan Stern
Index:
2.6.23-rc1/drivers/usb/core/hub.c
===================================================================drivers/usb/core/hub.c +0
-0@@ -1644,9 +1644,10 @@ static int finish_port_resume(struct usb* and device drivers will know about any resume quirks. drivers/usb/core/hub.c static int finish_port_resume(struct usb · line 1653
Quoted 10 lines
drivers/usb/core/hub.c +2
-1*/ if (status ==0 ) { + devstatus =0 ; status =usb_get_status (udev,USB_RECIP_DEVICE ,0 , &devstatus);if (status >=0 ) - status = (status ==2 ?0 : -ENODEV ); + status = (status >0 ?0 : -ENODEV ); }if (status) {Alan,
Yes, that patch worked, and dmesg now shows the device auto-suspending and resuming every few seconds. Thanks a lot. I hope you do merge this patch or a workaround like it.
Quoted 8 lines
Quoted 1 line
Dan
The same bug kills my Sandisk Cruzer Micro USB pen drives.
I plug them in, they work briefly, then the light goes out (abnormal), and 30-second timeout/reset is needed for each subsequent access. Ugh.They work fine in 2.6.22. I'll try the above patch here now and see if it fixes this regression.
Nope. Patch is already in -rc6 I see, so still NFG.
We can continue blacklisting the multitudes of b0rked devices one by one, or we can revert this change or default it to "off" for usb-storage (at least).
This really kills a lot of everyday devices. Here's my Sandisk Cruzer(s), after forcing autosuspend=0:
Bus 005 Device 014: ID 0781:5151 SanDisk Corp. Cruzer Micro 256/512MB Flash Drive Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0781 SanDisk Corp.
idProduct 0x5151 Cruzer Micro 256/512MB Flash Drive
bcdDevice 0.10
iManufacturer 1 SanDisk Corporation
iProduct 2 Cruzer Micro
iSerial 3 20060775000CF73334D3
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 200mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI bInterfaceProtocol 80 Bulk (Zip)
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 1
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)