How to use software encryption with WEP and mac80211
What do I need to do to get mac80211 to do software encryption for WEP? My port of the PHY code from bcm43xx and the mac80211 front end works with WPA encryption. With WEP, it authenticates and associates, but never gets an IP number from DHCP. That indicates to me that the encryption is not set up correctly. I looked through the various definitions in include/net/mac80211.h, but nothing seems to apply.
Thanks,
Larry
Quoted 5 lines · On Saturday 11 August 2007 05:25:11 Larry Finger wrote:
What do I need to do to get mac80211 to do software encryption for WEP? My port of the PHY code from bcm43xx and the mac80211 front end works with WPA encryption. With WEP, it authenticates and associates, but never gets an IP number from DHCP. That indicates to me that the encryption is not set up correctly. I looked through the various definitions in
include/net/mac80211.h, but nothing seems to apply.
Which hw enc code do you use in that tree? The old softmac crap or my new code from bcm43xx-mac80211?
Anyway, if you want to disable hw enc, always set the force sw enc bit in the set_key function and return early:
key->flags |= IEEE80211_KEY_FORCE_SW_ENCRYPT; return 0;
Signature · 1 line
Greetings Michael.
Quoted 5 lines · Michael Buesch
Quoted 1 line · On Saturday 11 August 2007 05:25:11 Larry Finger wrote:
What do I need to do to get mac80211 to do software encryption for WEP? My port of the PHY code from bcm43xx and the mac80211 front end works with WPA encryption. With WEP, it authenticates and associates, but never gets an IP number from DHCP. That indicates to me that the encryption is not set up correctly. I looked through the various definitions in
include/net/mac80211.h, but nothing seems to apply.Which hw enc code do you use in that tree? The old softmac crap or my new code from bcm43xx-mac80211?
I had stripped out all the key stuff, but before that it was from bcm43xx-mac80211.
Quoted 5 lines
Anyway, if you want to disable hw enc, always set the force sw enc bit in the
set_keyfunction and return early:key->flags |= IEEE80211_KEY_FORCE_SW_ENCRYPT; return 0;
This doesn't seem to work. I had tried it before. I guess I put your code back in again.
Thanks,
Larry
Quoted 13 lines · On Saturday 11 August 2007 17:05:28 Larry Finger wrote:
Quoted 9 lines · Michael Buesch
Quoted 5 lines · On Saturday 11 August 2007 05:25:11 Larry Finger wrote:
What do I need to do to get mac80211 to do software encryption for WEP? My port of the PHY code from bcm43xx and the mac80211 front end works with WPA encryption. With WEP, it authenticates and associates, but never gets an IP number from DHCP. That indicates to me that the encryption is not set up correctly. I looked through the various definitions in
include/net/mac80211.h, but nothing seems to apply.Which hw enc code do you use in that tree? The old softmac crap or my new code from bcm43xx-mac80211?
I had stripped out all the key stuff, but before that it was from bcm43xx-mac80211.
Quoted 7 lines
Quoted 5 lines
Anyway, if you want to disable hw enc, always set the force sw enc bit in the
set_keyfunction and return early:key->flags |= IEEE80211_KEY_FORCE_SW_ENCRYPT; return 0;This doesn't seem to work. I had tried it before. I guess I put your code back in again.
bcm43xx-mac80211 hwenc code does not work with v3 firmware. There is no working hwenc code for v3 firmware.
The above code should work to enable swenc, unless there's a bug in mac80211.
Signature · 1 line
Greetings Michael.
Quoted 7 lines · Michael Buesch
Quoted 1 line · On Saturday 11 August 2007 17:05:28 Larry Finger wrote:
This doesn't seem to work. I had tried it before. I guess I put your code back in again.
bcm43xx-mac80211 hwenc code does not work with v3 firmware. There is no working hwenc code for v3 firmware.
The above code should work to enable swenc, unless there's a bug in mac80211.
Thanks. That saves a lot of work. Now I know where to look.
Larry
Quoted 11 lines · Michael Buesch
Quoted 10 lines · On Saturday 11 August 2007 17:05:28 Larry Finger wrote:
Quoted 4 lines · Michael Buesch
Quoted 1 line · On Saturday 11 August 2007 05:25:11 Larry Finger wrote:
What do I need to do to get mac80211 to do software encryption for WEP? My port of the PHY code from bcm43xx and the mac80211 front end works with WPA encryption. With WEP, it authenticates and associates, but never gets an IP number from DHCP. That indicates to me that the encryption is not set up correctly. I looked through the various definitions in
include/net/mac80211.h, but nothing seems to apply.Which hw enc code do you use in that tree? The old softmac crap or my new code from bcm43xx-mac80211?
I had stripped out all the key stuff, but before that it was from bcm43xx-mac80211.
Quoted 3 lines
Anyway, if you want to disable hw enc, always set the force sw enc bit in the
set_keyfunction and return early:
Quoted 8 lines
Quoted 3 lines
Quoted 2 lines
key->flags |= IEEE80211_KEY_FORCE_SW_ENCRYPT; return 0;This doesn't seem to work. I had tried it before. I guess I put your code back in again.
bcm43xx-mac80211 hwenc code does not work with v3 firmware. There is no working hwenc code for v3 firmware.
The above code should work to enable swenc, unless there's a bug in mac80211.
It wasn't a bug in mac80211. In fact, it forces software encryption if the set_key callback is not specified. My problem was that the hw->flags were wrong in the initial registration of the iface. Both WEP and WPA are working now.
Larry