Skip to contentSkip to conversation

Atmel AT49BV320C support in Uboot

U-Boot-Users raj reddy 2 participants 4 messages Sep 6, 2007 – Sep 11, 2007

lore
Share & tools
lore
#1 lore raw
Quoted 4 lines · In message <[email protected]> you wrote:

Can any one help me, how to add support for the AT49BV320C (command Flash Interface) support for the uboot.

If this flashis CFI conform, just use the existing CFI driver. Search for CFG_FLASH_CFI* in the existing board config files to get an idea.

Best regards,

Wolfgang Denk

Signature · 5 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Without freedom of choice there is no creativity.
	-- Kirk, "The return of the Archons", stardate 3157.4
author
#2 lore raw

CFI supports only the same size sector flash, but AT49BV320C organized like
8 * 4K
63 * 32K
similar flash driver i saw in the board/at91rm9200dk/flash.c file. I took that file and tried to modify the commands, but i am getting the following Error...

=> saveenv
Saving Environment to Flash...
Protect off FFFB8000 ... FFFBFFFF Un-Protecting sectors 62..62 in bank 1 Un-Protected 1 sectors
Protect off FFFB0000 ... FFFB7FFF Un-Protecting sectors 61..61 in bank 1 Un-Protected 1 sectors
Data to save 0x4000
Data (start 0xfffb4000, len 0x4000) saved at 0xfac1b8 Erasing Flash... FFFB0000 ... FFFB7FFF ...Erase Flash from 0xfffb0000 to 0xfffb7fff in Bank # 1 Erasing sector 61 ... ok.
Erased 1 sectors
Writing to Flash... FFFB0005 ... FFFB4000 ... unaligned destination not supported
Start and/or end address not on sector boundary

is't the right procedure what i am trying to add the flash support for AT49BV320C

Quoted 9 lines · --- Wolfgang Denk

In message
<[email protected]> you

Quoted 3 lines · wrote:

Can any one help me, how to add support for the
AT49BV320C (command Flash Interface) support for

the

Quoted 1 line

uboot.

Quoted 20 lines

If this flashis CFI conform, just use the existing CFI driver. Search
for CFG_FLASH_CFI* in the existing board config files to get an idea.

Best regards,

Wolfgang Denk

Signature · 9 lines
DENX Software Engineering GmbH,     MD: Wolfgang
Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194
Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80
Email: wd at denx.de
Without freedom of choice there is no creativity.
	-- Kirk, "The return of the Archons", stardate
3157.4

Did you know? You can CHAT without downloading messenger. Go to http://in.messenger.yahoo.com/webmessengerpromo.php/

#3 lore raw
Quoted 1 line · In message <[email protected]> you wrote:

CFI supports only the same size sector flash, but

This is wrong. Th CFI flash driver also supports bottom and top boot sector types.

Best regards,

Wolfgang Denk

Signature · 6 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
... bacteriological warfare ... hard to believe we were once foolish
enough to play around with that.
	-- McCoy, "The Omega Glory", stardate unknown