BUG: skge ethernet breakage (PCI: Unable to reserve mem region)

Jan Gukelberger

author

2007-09-07 16:42 UTC #0 lore raw

Hi,

I originally reported this bug to the Debian BTS:
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=441232
There I was told to talk directly to upstream.

I am pasting the original bug report below. The referenced text files can be found at the mentioned BTS URL.
Additionally, I have just tried Linux 2.6.23-rc5 and am attaching the corresponding dmesg output.

Thanks in advance for any help,
Jan

With recent kernels my on-board network adapter does not work any more. This is a Marvell Gigabit Ethernet Controller on an Asus P5B-V mainboard.

This is the same bug as #428452 reported earlier against linux-image-2.6.21-1-amd64. (Sorry for the duplicate, I didn't know how to extend the old report to newer kernel versions.)
In fact, the network adapter hasn't been working since then, i.e. the last working kernel image was 2.6.20-1-amd64 (which I am using now). The following images 2.6.2[12]-[12]-amd64 have all exposed the same problem.

The key problem seem to be the following lines in dmesg:
------------------------------------------------------------------------
ACPI: PCI Interrupt 0000:04:04.0[A] -> GSI 19 (level, low) -> IRQ 19
PCI: Unable to reserve mem region #1:4000@ff9f8000 for device 0000:04:04.0 skge 0000:04:04.0: cannot obtain PCI resources
ACPI: PCI interrupt for device 0000:04:04.0 disabled
skge: probe of 0000:04:04.0 failed with error -16
------------------------------------------------------------------------

I'm attaching full 'dmesg' output from working (2.6.20-1) and broken (2.6.22-2) kernel versions as well as the output of 'lspci -vvv' on the most recent kernel.

If you need any other information or I can try something please let me know.

Linux version 2.6.23-rc5-amd64 (Debian 2.6.23~rc5-1~experimental.1~snapshot.9462) ([email protected]) (gcc version 4.1.3 20070718 (prerelease) (Debian 4.1.2-14+1)) #1 SMP Thu Sep 6 06:18:52 UTC 2007 Command line: root=/dev/sda6 ro quiet vga=791
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009ec00 (usable)
BIOS-e820: 000000000009ec00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007ef90000 (usable)
BIOS-e820: 000000007ef90000 - 000000007ef9e000 (ACPI data)
BIOS-e820: 000000007ef9e000 - 000000007efe0000 (ACPI NVS)
BIOS-e820: 000000007efe0000 - 000000007f000000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
Entering add_active_range(0, 0, 158) 0 entries of 3200 used
Entering add_active_range(0, 256, 520080) 1 entries of 3200 used
end_pfn_map = 1048576
DMI 2.4 present.
ACPI: RSDP 000FAD70, 0024 (r2 ACPIAM)
ACPI: XSDT 7EF90100, 006C (r1 NEC 5000730 MSFT 97)
ACPI: FACP 7EF90290, 00F4 (r3 MSTEST OEMFACP 5000730 MSFT 97)
ACPI: DSDT 7EF905C0, 9C85 (r1 A0579 A0579000 0 INTL 20060113)
ACPI: FACS 7EF9E000, 0040
ACPI: APIC 7EF90390, 006C (r1 MSTEST OEMAPIC 5000730 MSFT 97)
ACPI: MCFG 7EF90400, 003C (r1 MSTEST OEMMCFG 5000730 MSFT 97)
ACPI: SLIC 7EF90440, 0176 (r1 NEC 5000730 MSFT 97)
ACPI: OEMB 7EF9E040, 007B (r1 MSTEST AMI_OEM 5000730 MSFT 97)
ACPI: HPET 7EF9A250, 0038 (r1 MSTEST OEMHPET 5000730 MSFT 97)
ACPI: GSCI 7EF9E0C0, 2024 (r1 MSTEST GMCHSCI 5000730 MSFT 97)
ACPI: SSDT 7EFA00F0, 01BF (r1 AMI CPU1PM 1 INTL 20060113)
ACPI: SSDT 7EFA02B0, 0133 (r1 AMI CPU2PM 1 INTL 20060113)
No NUMA configuration found
Faking a node at 0000000000000000-000000007ef90000
Entering add_active_range(0, 0, 158) 0 entries of 3200 used
Entering add_active_range(0, 256, 520080) 1 entries of 3200 used
Bootmem setup node 0 0000000000000000-000000007ef90000
Zone PFN ranges:
DMA 0 -> 4096
DMA32 4096 -> 1048576
Normal 1048576 -> 1048576
Movable zone start PFN for each node
early_node_map[2] active PFN ranges

    0:        0 ->      158
    0:      256 ->   520080

On node 0 totalpages: 519982
DMA zone: 56 pages used for memmap
DMA zone: 1044 pages reserved
DMA zone: 2898 pages, LIFO batch:0
DMA32 zone: 7054 pages used for memmap
DMA32 zone: 508930 pages, LIFO batch:31
Normal zone: 0 pages used for memmap
Movable zone: 0 pages used for memmap
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
ACPI: HPET id: 0x8086a202 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
swsusp: Registered nosave memory region: 000000000009e000 - 000000000009f000
swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e4000
swsusp: Registered nosave memory region: 00000000000e4000 - 0000000000100000 Allocating PCI resources starting at 80000000 (gap: 7f000000:7fe00000)
SMP: Allowing 4 CPUs, 2 hotplug CPUs
PERCPU: Allocating 35176 bytes of per cpu data
Built 1 zonelists in Node order. Total pages: 511828
Policy zone: DMA32
Kernel command line: root=/dev/sda6 ro quiet vga=791
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Extended CMOS year: 2000
time.c: Detected 2399.997 MHz processor.
Console: colour dummy device 80x25
console [tty0] enabled
Checking aperture...
Calgary: detecting Calgary via BIOS EBDA area
Calgary: Unable to locate Rio Grande table in EBDA - bailing!
Memory: 2041096k/2080320k available (2066k kernel code, 38832k reserved, 977k data, 304k init) Calibrating delay using timer specific routine.. 4803.34 BogoMIPS (lpj=9606690) Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Mount-cache hash table entries: 256
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU 0/0 -> Node 0
using mwait in idle threads.
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU0: Thermal monitoring enabled (TM2)
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
Using local APIC timer interrupts.
result 16666629
Detected 16.666 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 4800.03 BogoMIPS (lpj=9600060)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU 1/1 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU1: Thermal monitoring enabled (TM2)
Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz stepping 06
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: Using configuration type 1
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 0480-04bf claimed by ICH6 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 *15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 *14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 10 11 12 14 15)
ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - CD, should be C4 [20070126] Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: ACPI device : hid PNP0A08
pnp: ACPI device : hid PNP0C01
pnp: ACPI device : hid PNP0200
pnp: ACPI device : hid PNP0B00
pnp: ACPI device : hid PNP0800
pnp: ACPI device : hid PNP0C04
pnp: ACPI device : hid PNP0501
pnp: ACPI device : hid PNP0700
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0103
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0303
pnp: ACPI device : hid PNP0F03
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0C01
pnp: PnP ACPI: found 16 devices
ACPI: ACPI bus type pnp unregistered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NET: Registered protocol family 8
NET: Registered protocol family 20
PCI-GART: No AMD northbridge found.
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 64-bit timers, 14318180 Hz
ACPI: RTC can wake from S4
Time: tsc clocksource has been installed.
pnp: the driver 'system' has been registered
pnp: match found with the PnP device '00:01' and the driver 'system'
pnp: 00:01: iomem range 0xfed14000-0xfed19fff has been reserved
pnp: match found with the PnP device '00:08' and the driver 'system'
pnp: 00:08: ioport range 0x290-0x297 has been reserved
pnp: match found with the PnP device '00:09' and the driver 'system'
pnp: 00:09: iomem range 0xfed1c000-0xfed1ffff has been reserved
pnp: 00:09: iomem range 0xfed20000-0xfed8ffff has been reserved
pnp: 00:09: iomem range 0xff9fa000-0xff9fafff has been reserved
pnp: 00:09: iomem range 0xfff00000-0xfffffffe could not be reserved
pnp: match found with the PnP device '00:0b' and the driver 'system'
pnp: 00:0b: iomem range 0xfec00000-0xfec00fff has been reserved
pnp: 00:0b: iomem range 0xfee00000-0xfee00fff could not be reserved
pnp: match found with the PnP device '00:0e' and the driver 'system'
pnp: 00:0e: iomem range 0xe0000000-0xefffffff has been reserved
pnp: match found with the PnP device '00:0f' and the driver 'system'
pnp: 00:0f: iomem range 0x0-0x9ffff could not be reserved
pnp: 00:0f: iomem range 0xc0000-0xcffff has been reserved
pnp: 00:0f: iomem range 0xe0000-0xfffff could not be reserved
pnp: 00:0f: iomem range 0x100000-0x7effffff could not be reserved
PCI: Bridge: 0000:00:01.0
IO window: 8000-afff
MEM window: ff700000-ff7fffff
PREFETCH window: bfe00000-dfdfffff
PCI: Bridge: 0000:00:1c.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: dfe00000-dfefffff
PCI: Bridge: 0000:00:1c.4
IO window: b000-bfff
MEM window: ff800000-ff8fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
IO window: c000-cfff
MEM window: ff900000-ff9fffff
PREFETCH window: 80000000-800fffff
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1c.4 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 262144 (order: 10, 6291456 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 5950k freed
audit: initializing netlink socket (disabled)
audit(1189181505.780:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:01:00.0
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:01.0:pcie00]
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
PCI: Setting latency timer of device 0000:00:1c.4 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.4:pcie00]
Allocate Port Service[0000:00:1c.4:pcie02]
vesafb: framebuffer at 0xc0000000, mapped to 0xffffc20000b00000, using 3072k, total 16384k
vesafb: mode is 1024x768x16, linelength=2048, pages=9
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
Real Time Clock Driver v1.12ac
hpet_resources: 0xfed00000 is busy
Linux agpgart interface v0.102
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
pnp: the driver 'serial' has been registered
pnp: match found with the PnP device '00:06' and the driver 'serial'
00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
pnp: the driver 'i8042 kbd' has been registered
pnp: match found with the PnP device '00:0c' and the driver 'i8042 kbd'
pnp: the driver 'i8042 aux' has been registered
pnp: match found with the PnP device '00:0d' and the driver 'i8042 aux'
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Freeing unused kernel memory: 304k freed
input: AT Translated Set 2 keyboard as /class/input/input0
ACPI Exception (processor_core-0797): AE_NOT_FOUND, Processor Device is not present [20070126] ACPI Exception (processor_core-0797): AE_NOT_FOUND, Processor Device is not present [20070126] USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1a.0 to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000e000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
pnp: the driver 'ide' has been registered
Floppy drive(s): fd0 is 1.44M
SCSI subsystem initialized
libata version 2.21 loaded.
FDC 0 is a post-1991 82077
ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1a.1 to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1a.1: irq 17, io base 0x0000e080
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000d800
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000d880
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000dc00
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:04:04.0[A] -> GSI 19 (level, low) -> IRQ 19
PCI: Unable to reserve mem region #1:4000@ff9f8000 for device 0000:04:04.0
skge 0000:04:04.0: cannot obtain PCI resources
ACPI: PCI interrupt for device 0000:04:04.0 disabled
skge: probe of 0000:04:04.0 failed with error -16
ACPI: PCI Interrupt 0000:04:03.0[A] -> GSI 21 (level, low) -> IRQ 21
firewire_ohci: Added fw-ohci device 0000:04:03.0, OHCI version 1.10
ahci 0000:00:1f.2: version 2.3
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
firewire_core: created new fw device fw0 (0 config rom retries, S400)
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0x33 impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq sntf ilck stag pm led clo pmp pio slum part
PCI: Setting latency timer of device 0000:00:1f.2 to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
scsi4 : ahci
scsi5 : ahci
ata1: SATA max UDMA/133 cmd 0xffffc20000ac2900 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 1276
ata2: SATA max UDMA/133 cmd 0xffffc20000ac2980 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 1276
ata3: DUMMY
ata4: DUMMY
ata5: SATA max UDMA/133 cmd 0xffffc20000ac2b00 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 1276
ata6: SATA max UDMA/133 cmd 0xffffc20000ac2b80 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 1276
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-7: SAMSUNG HD401LJ, ZZ100-15, max UDMA7
ata1.00: 781422768 sectors, multi 0: LBA48 NCQ (not used)
ata1.00: configured for UDMA/133
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.00: ATAPI: HL-DT-STDVD-RAM GSA-H30N, 1.01, max UDMA/100
ata2.00: configured for UDMA/100
ata5: SATA link down (SStatus 0 SControl 300)
ata6: SATA link down (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access ATA SAMSUNG HD401LJ ZZ10 PQ: 0 ANSI: 5
scsi 1:0:0:0: CD-ROM HL-DT-ST DVD-RAM GSA-H30N 1.01 PQ: 0 ANSI: 5
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1a.7 to 64
ehci_hcd 0000:00:1a.7: EHCI Host Controller
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 6
ehci_hcd 0000:00:1a.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1a.7
ehci_hcd 0000:00:1a.7: irq 18, io mem 0xffaff000
ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 4 ports detected
ahci 0000:02:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
ahci 0000:02:00.0: flags: 64bit ncq pm led clo pmp pio slum part
PCI: Setting latency timer of device 0000:02:00.0 to 64
scsi6 : ahci
scsi7 : ahci
ata7: SATA max UDMA/133 cmd 0xffffc20000ac4100 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 16
ata8: SATA max UDMA/133 cmd 0xffffc20000ac4180 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 16
ata7: SATA link down (SStatus 0 SControl 300)
ata8: SATA link down (SStatus 0 SControl 300)
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 7
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xffafec00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 6 ports detected
sd 0:0:0:0: [sda] 781422768 512-byte hardware sectors (400088 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 781422768 512-byte hardware sectors (400088 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 < sda5 sda6 sda7 >
sd 0:0:0:0: [sda] Attached SCSI disk
JMB363: IDE controller at PCI slot 0000:02:00.1
PCI: Enabling device 0000:02:00.1 (0000 -> 0001)
ACPI: PCI Interrupt 0000:02:00.1[B] -> GSI 17 (level, low) -> IRQ 17
JMB363: chipset revision 2
JMB363: 100% native mode on irq 17
PCI: Setting latency timer of device 0000:02:00.1 to 64

    ide0: BM-DMA at 0xb400-0xb407, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xb408-0xb40f, BIOS settings: hdc:pio, hdd:pio

Probing IDE interface ide0...
sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 1:0:0:0: Attached scsi generic sg1 type 5
hdb: WDC WD400BB-00AUA1, ATA DISK drive
hdb: selected mode 0x45
ide0 at 0xbc00-0xbc07,0xb882 on irq 17
Probing IDE interface ide1...
hdb: max request size: 128KiB
hdb: 78165360 sectors (40020 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
hdb: cache flushes not supported
hdb: hdb1 hdb2 < hdb5 hdb6 hdb7 hdb8 hdb9 hdb10 hdb11 >
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
input: PC Speaker as /class/input/input1
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
iTCO_wdt: Found a ICH8 or ICH8R TCO device (Version=2, TCOBASE=0x0860)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
input: Power Button (FF) as /class/input/input2
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input3
ACPI: Power Button (CM) [PWRB]
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:1b.0 to 64
hda_codec: Unknown model for AD1988, trying auto-probe from BIOS... Linux video capture interface: v2.00
PCI: Enabling device 0000:00:1f.3 (0001 -> 0003)
ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 18 (level, low) -> IRQ 18
logips2pp: Detected unknown logitech mouse model 95
saa7146: register extension 'dvb'.
ACPI: PCI Interrupt 0000:04:01.0[A] -> GSI 22 (level, low) -> IRQ 22
saa7146: found saa7146 @ mem ffffc20000ace800 (revision 1, irq 22) (0x13c2,0x0003).
DVB: registering new adapter (Technotrend/Hauppauge WinTV Nexus-S rev2.X) adapter has MAC addr = 00:d0:5c:22:68:cc
dvb-ttpci: gpioirq unknown type=0 len=0
dvb-ttpci: info @ card 0: firm f0240009, rtsl b0250018, vid 71010068, app 80002622
dvb-ttpci: firmware @ card 0 supports CI link layer interface
input: ImExPS/2 Logitech Explorer Mouse as /class/input/input4
dvb-ttpci: adac type set to 0 @ card 0
saa7146_vv: saa7146 (0): registered device video0 [v4l2]
saa7146_vv: saa7146 (0): registered device vbi0 [v4l2]
DVB: registering frontend 0 (ST STV0299 DVB-S)...
input: DVB on-card IR receiver as /class/input/input5
dvb-ttpci: found av7110-0.
EXT3 FS on sda6, internal journal
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: [email protected] kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended EXT3 FS on sda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
pnp: the driver 'parport_pc' has been registered
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
[drm] Initialized drm 1.1.0 20060810
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16 [drm] Initialized radeon 1.28.0 20060524 on minor 0
[drm] Setting GART location based on new memory map
[drm] Loading R300 Microcode
[drm] writeback test succeeded in 1 usecs

Stephen Hemminger

2007-09-11 08:20 UTC #1 lore raw

Quoted 35 lines · On Fri, 07 Sep 2007 18:42:35 +0200 Jan Gukelberger <[email protected]> wrote:

Hi,
I originally reported this bug to the Debian BTS:
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=441232
There I was told to talk directly to upstream.
I am pasting the original bug report below. The referenced text files can be found at the mentioned BTS URL.
Additionally, I have just tried Linux 2.6.23-rc5 and am attaching the corresponding dmesg output.
Thanks in advance for any help,
Jan
With recent kernels my on-board network adapter does not work any more. This is a Marvell Gigabit Ethernet Controller on an Asus P5B-V mainboard.
This is the same bug as #428452 reported earlier against linux-image-2.6.21-1-amd64. (Sorry for the duplicate, I didn't know how to extend the old report to newer kernel versions.)
In fact, the network adapter hasn't been working since then, i.e. the last working kernel image was 2.6.20-1-amd64 (which I am using now). The following images 2.6.2[12]-[12]-amd64 have all exposed the same problem.
The key problem seem to be the following lines in dmesg:
------------------------------------------------------------------------
ACPI: PCI Interrupt 0000:04:04.0[A] -> GSI 19 (level, low) -> IRQ 19
PCI: Unable to reserve mem region #1:4000@ff9f8000 for device 0000:04:04.0 skge 0000:04:04.0: cannot obtain PCI resources
ACPI: PCI interrupt for device 0000:04:04.0 disabled
skge: probe of 0000:04:04.0 failed with error -16
------------------------------------------------------------------------

Quoted 6 lines

I'm attaching full 'dmesg' output from working (2.6.20-1) and broken (2.6.22-2) kernel versions as well as the output of 'lspci -vvv' on the most recent kernel.
If you need any other information or I can try something please let me know.

There is some kind of device conflict, please provide lspci -vvvxx output.

Jan Gukelberger

author

2007-09-11 10:58 UTC #2 lore raw

Quoted 2 lines · Stephen Hemminger

On Fri, 07 Sep 2007 18:42:35 +0200
Jan Gukelberger <[email protected]> wrote:

[...]

Quoted 11 lines

Quoted 9 lines
The key problem seem to be the following lines in dmesg:
------------------------------------------------------------------------
ACPI: PCI Interrupt 0000:04:04.0[A] -> GSI 19 (level, low) -> IRQ 19
PCI: Unable to reserve mem region #1:4000@ff9f8000 for device 0000:04:04.0 skge 0000:04:04.0: cannot obtain PCI resources
ACPI: PCI interrupt for device 0000:04:04.0 disabled
skge: probe of 0000:04:04.0 failed with error -16
------------------------------------------------------------------------
There is some kind of device conflict, please provide lspci -vvvxx output.

I'm attaching the output of 'lspci -vvvxx' on the working 2.6.20 kernel as well as the output of 'lspci -vvxxx' on 2.6.23-rc5 which I recorded earlier.
I you specifically need 'lspci -vvvxx' on 2.6.23-rc5 please drop me a note and I'll reboot quickly.

Thanks,
Jan

00:00.0 Host bridge: Intel Corporation 82P965/G965 Memory Controller Hub (rev 02)
Subsystem: ASUSTeK Computer Inc. Unknown device 820b
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00: 86 80 a0 29 06 00 90 20 02 00 00 06 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 0b 82
30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00

00:01.0 PCI bridge: Intel Corporation 82P965/G965 PCI Express Root Port (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00008000-0000afff
Memory behind bridge: ff700000-ff7fffff
Prefetchable memory behind bridge: 00000000bfe00000-00000000dfdfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [88] Subsystem: Intel Corporation Unknown device 0000
Capabilities: [80] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee00000 Data: 4049
Capabilities: [a0] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s, Port 2
Link: Latency L0s <256ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x16
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
00: 86 80 a1 29 07 05 10 00 02 00 04 06 08 00 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 00 80 a0 00 00
20: 70 ff 70 ff e1 bf d1 df 00 00 00 00 00 00 00 00
30: 00 00 00 00 88 00 00 00 00 00 00 00 0b 01 0a 00

00:03.0 Communication controller: Intel Corporation 82P965/G965 HECI Controller (rev 02)
Subsystem: ASUSTeK Computer Inc. Unknown device 820b
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at ffaff400 (64-bit, non-prefetchable) [size=16]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [8c] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
00: 86 80 a4 29 06 00 18 00 02 00 80 07 00 00 80 00
10: 04 f4 af ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 0b 82
30: 00 00 00 00 50 00 00 00 00 00 00 00 0b 01 00 00

00:1a.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI #4 (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 81ec
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at e000 [size=32]
00: 86 80 34 28 05 00 80 02 02 00 03 0c 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 e0 00 00 00 00 00 00 00 00 00 00 43 10 ec 81
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 00 00

00:1a.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI #5 (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 81ec
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at e080 [size=32]
00: 86 80 35 28 05 00 80 02 02 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 81 e0 00 00 00 00 00 00 00 00 00 00 43 10 ec 81
30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 02 00 00

00:1a.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI #2 (rev 02) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 81ec
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 0: Memory at ffaff000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
00: 86 80 3a 28 06 00 90 02 02 20 03 0c 00 00 00 00
10: 00 f0 af ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 ec 81
30: 00 00 00 00 50 00 00 00 00 00 00 00 05 03 00 00

00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 02)
Subsystem: ASUSTeK Computer Inc. Unknown device 821a
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at ffaf8000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express Unknown type IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed unknown, Width x0, ASPM unknown, Port 0
Link: Latency L0s <64ns, L1 <1us
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed unknown, Width x0
00: 86 80 4b 28 06 00 10 00 02 00 03 04 08 00 00 00
10: 04 80 af ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 1a 82
30: 00 00 00 00 50 00 00 00 00 00 00 00 03 01 00 00

00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 02) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000dfe00000-00000000dfefffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x2, ASPM L0s L1, Port 1
Link: Latency L0s <1us, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x0
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee00000 Data: 4051
Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Unknown device 821a
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 86 80 3f 28 06 05 10 00 02 00 04 06 08 00 81 00
10: 00 00 00 00 00 00 00 00 00 03 03 00 f0 00 00 20
20: f0 ff 00 00 e1 df e1 df 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 01 02 00

00:1c.4 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 5 (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: ff800000-ff8fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 5
Link: Latency L0s <256ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee00000 Data: 4059
Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Unknown device 821a
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 86 80 47 28 07 05 10 00 02 00 04 06 08 00 81 00
10: 00 00 00 00 00 00 00 00 00 02 02 00 b0 b0 00 00
20: 80 ff 80 ff f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 01 02 00

00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI #1 (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 81ec
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at d800 [size=32]
00: 86 80 30 28 05 00 80 02 02 00 03 0c 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 d8 00 00 00 00 00 00 00 00 00 00 43 10 ec 81
30: 00 00 00 00 00 00 00 00 00 00 00 00 07 01 00 00

00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI #2 (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 81ec
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at d880 [size=32]
00: 86 80 31 28 05 00 80 02 02 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 81 d8 00 00 00 00 00 00 00 00 00 00 43 10 ec 81
30: 00 00 00 00 00 00 00 00 00 00 00 00 0f 02 00 00

00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI #3 (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 81ec
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at dc00 [size=32]
00: 86 80 32 28 05 00 80 02 02 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 dc 00 00 00 00 00 00 00 00 00 00 43 10 ec 81
30: 00 00 00 00 00 00 00 00 00 00 00 00 05 03 00 00

00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI #1 (rev 02) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 81ec
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at ffafec00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
00: 86 80 36 28 06 00 90 02 02 20 03 0c 00 00 00 00
10: 00 ec af ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 ec 81
30: 00 00 00 00 50 00 00 00 00 00 00 00 07 01 00 00

00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev f2) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: ff900000-ff9fffff
Prefetchable memory behind bridge: 0000000080000000-00000000800fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Subsystem: ASUSTeK Computer Inc. Unknown device 821a
00: 86 80 4e 24 07 01 10 00 f2 01 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 04 04 20 c0 c0 80 22
20: 90 ff 90 ff 01 80 01 80 00 00 00 00 00 00 00 00
30: 00 00 00 00 50 00 00 00 00 00 00 00 ff 00 02 00

00:1f.0 ISA bridge: Intel Corporation 82801HB/HR (ICH8/R) LPC Interface Controller (rev 02)
Subsystem: ASUSTeK Computer Inc. Unknown device 821a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00: 86 80 10 28 07 00 10 02 02 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 1a 82
30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00

00:1f.2 SATA controller: Intel Corporation 82801HR/HO/HH (ICH8R/DO/DH) SATA AHCI Controller (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: ASUSTeK Computer Inc. Unknown device 821a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 1276
Region 0: I/O ports at ec00 [size=8]
Region 1: I/O ports at e880 [size=4]
Region 2: I/O ports at e800 [size=8]
Region 3: I/O ports at e480 [size=4]
Region 4: I/O ports at e400 [size=32]
Region 5: Memory at ffaff800 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/4 Enable+
Address: fee00000 Data: 4079
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] #12 [0010]
00: 86 80 24 28 07 04 b0 02 02 01 06 01 00 00 00 00
10: 01 ec 00 00 81 e8 00 00 01 e8 00 00 81 e4 00 00
20: 01 e4 00 00 00 f8 af ff 00 00 00 00 43 10 1a 82
30: 00 00 00 00 80 00 00 00 00 00 00 00 0f 02 00 00

00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 02)
Subsystem: ASUSTeK Computer Inc. Unknown device 821a
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at 80100000 (32-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 0400 [size=32]
00: 86 80 3e 28 03 00 80 02 02 00 05 0c 00 00 00 00
10: 00 00 10 80 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 04 00 00 00 00 00 00 00 00 00 00 43 10 1a 82
30: 00 00 00 00 00 00 00 00 00 00 00 00 0f 03 00 00

01:00.0 VGA compatible controller: ATI Technologies Inc R480 [Radeon X800 GTO (PCIE)] (prog-if 00 [VGA])
Subsystem: PC Partner Limited Unknown device 1600
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at c0000000 (64-bit, prefetchable) [size=256M]
Region 2: Memory at ff7f0000 (64-bit, non-prefetchable) [size=64K]
Region 4: I/O ports at a000 [size=256]
Expansion ROM at ff7c0000 [disabled] [size=128K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <256ns, L1 <4us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port 0
Link: Latency L0s <256ns, L1 <2us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x16
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
00: 02 10 4f 5d 07 00 10 00 00 00 00 03 08 00 80 00
10: 0c 00 00 c0 00 00 00 00 04 00 7f ff 00 00 00 00
20: 01 a0 00 00 00 00 00 00 00 00 00 00 4b 17 00 16
30: 00 00 7c ff 50 00 00 00 00 00 00 00 0b 01 00 00

01:00.1 Display controller: ATI Technologies Inc R480 [Radeon X800 GTO (PCIE)] (Secondary)
Subsystem: PC Partner Limited Unknown device 1601
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Region 0: Memory at ff7e0000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <256ns, L1 <4us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port 0
Link: Latency L0s <256ns, L1 <2us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x16
00: 02 10 6f 5d 07 00 10 00 00 00 80 03 08 00 00 00
10: 04 00 7e ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 4b 17 01 16
30: 00 00 00 00 50 00 00 00 00 00 00 00 ff 00 00 00

02:00.0 IDE interface: JMicron Technologies, Inc. JMicron 20360/20363 AHCI Controller (rev 02) (prog-if 01 [PriO])
Subsystem: ASUSTeK Computer Inc. Unknown device 81e4
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 5: Memory at ff8fe000 (32-bit, non-prefetchable) [size=8K]
Expansion ROM at ff8e0000 [disabled] [size=64K]
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Express Legacy Endpoint IRQ 1
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s, Port 1
Link: Latency L0s <1us, L1 <16us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
00: 7b 19 63 23 07 00 10 00 02 01 06 01 08 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 e0 8f ff 00 00 00 00 43 10 e4 81
30: 00 00 8e ff 68 00 00 00 00 00 00 00 0b 01 00 00

02:00.1 IDE interface: JMicron Technologies, Inc. JMicron 20360/20363 AHCI Controller (rev 02) (prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc. Unknown device 81e4
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at bc00 [size=8]
Region 1: I/O ports at b880 [size=4]
Region 2: I/O ports at b800 [size=8]
Region 3: I/O ports at b480 [size=4]
Region 4: I/O ports at b400 [size=16]
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 7b 19 63 23 05 00 10 00 02 85 01 01 00 00 00 00
10: 01 bc 00 00 81 b8 00 00 01 b8 00 00 81 b4 00 00
20: 01 b4 00 00 00 00 00 00 00 00 00 00 43 10 e4 81
30: 00 00 00 00 68 00 00 00 00 00 00 00 00 02 00 00

04:00.0 Class ff00: Measurement Computing PCI-DAS6025 (rev 02)

	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64, Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 14
	Region 0: Memory at ff9ffc00 (32-bit, non-prefetchable) [size=256]
	Region 1: I/O ports at c800 [size=256]
	Region 2: Memory at ff9fe000 (32-bit, non-prefetchable) [size=4K]
	Region 3: Memory at ff9fd000 (32-bit, non-prefetchable) [size=4K]

00: 07 13 5e 00 17 00 80 02 02 00 00 ff 08 40 00 00 10: 00 fc 9f ff 01 c8 00 00 00 e0 9f ff 00 d0 9f ff 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 0e 01 00 00

04:01.0 Multimedia controller: Philips Semiconductors SAA7146 (rev 01)
Subsystem: Technotrend Systemtechnik GmbH Technotrend/Hauppauge DVB card rev2.1
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (3750ns min, 9500ns max)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at ff9ff800 (32-bit, non-prefetchable) [size=512]
00: 31 11 46 71 06 00 80 02 01 00 80 04 00 40 00 00
10: 00 f8 9f ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 c2 13 03 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 03 01 0f 26

04:03.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev c0) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 81fe
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at ff9ff000 (32-bit, non-prefetchable) [size=2K]
Region 1: I/O ports at cc00 [size=128]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 44 30 17 00 10 02 c0 10 00 0c 08 40 00 00
10: 00 f0 9f ff 01 cc 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 fe 81
30: 00 00 00 00 50 00 00 00 00 00 00 00 0e 01 00 20

04:04.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001 Gigabit Ethernet Controller (rev 14)
Subsystem: ASUSTeK Computer Inc. Marvell 88E8001 Gigabit Ethernet Controller (Asus)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (5750ns min, 7750ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at ff9f8000 (32-bit, non-prefetchable) [size=16K]
Region 1: I/O ports at c400 [size=256]
Expansion ROM at 80000000 [disabled] [size=128K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
00: ab 11 20 43 17 00 b0 02 14 00 00 02 08 40 00 00
10: 00 80 9f ff 01 c4 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 1a 81
30: 00 00 9c ff 48 00 00 00 00 00 00 00 0f 01 17 1f

00:00.0 Host bridge: Intel Corporation 82P965/G965 Memory Controller Hub (rev 02)
Subsystem: ASUSTeK Computer Inc. Unknown device 820b
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00: 86 80 a0 29 06 00 90 20 02 00 00 06 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 0b 82
30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00
40: 01 90 d1 fe 00 00 00 00 01 40 d1 fe 00 00 00 00
50: 00 00 02 00 43 00 00 00 00 00 00 00 00 00 00 00
60: 01 00 00 e0 00 00 00 00 01 80 d1 fe 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 10 11 11 01 00 33 33 00 ff 03 00 00 00 0a 38 00
a0: 20 00 00 08 00 00 00 7f 00 00 00 00 00 00 00 7f
b0: 00 7f 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 49 00 00 00 00 00 00 13
e0: 09 00 09 51 6e 03 00 89 86 0c 00 00 00 00 00 00
f0: 02 00 00 00 00 00 00 00 90 0f 04 00 00 00 00 00

00:01.0 PCI bridge: Intel Corporation 82P965/G965 PCI Express Root Port (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00008000-0000afff
Memory behind bridge: ff700000-ff7fffff
Prefetchable memory behind bridge: 00000000bfe00000-00000000dfdfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [88] Subsystem: Intel Corporation Unknown device 0000
Capabilities: [80] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee0300c Data: 4159
Capabilities: [a0] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s, Port 2
Link: Latency L0s <256ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x16
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
00: 86 80 a1 29 07 05 10 00 02 00 04 06 08 00 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 00 80 a0 00 00
20: 70 ff 70 ff e1 bf d1 df 00 00 00 00 00 00 00 00
30: 00 00 00 00 88 00 00 00 00 00 00 00 0b 01 0a 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 02
80: 01 90 03 c8 08 00 00 00 0d 80 00 00 86 80 00 00
90: 05 a0 01 00 0c 30 e0 fe 59 41 00 00 00 00 00 00
a0: 10 00 41 01 00 80 00 00 0f 00 00 00 01 25 01 02
b0: 40 00 01 11 00 00 04 00 c0 01 48 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 01 00 03 e1 3f 00 90 0f 04 00 00 00 00 00

00:03.0 Communication controller: Intel Corporation 82P965/G965 HECI Controller (rev 02)
Subsystem: ASUSTeK Computer Inc. Unknown device 820b
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at ffaff400 (64-bit, non-prefetchable) [size=16]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [8c] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
00: 86 80 a4 29 06 00 18 00 02 00 80 07 00 00 80 00
10: 04 f4 af ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 0b 82
30: 00 00 00 00 50 00 00 00 00 00 00 00 0b 01 00 00
40: 02 00 01 40 00 00 00 00 00 00 00 00 00 00 00 00
50: 01 8c 03 c8 08 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 05 00 80 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:1a.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI #4 (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 81ec
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at e000 [size=32]
00: 86 80 34 28 05 00 80 02 02 00 03 0c 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 e0 00 00 00 00 00 00 00 00 00 00 43 10 ec 81
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 2f 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 86 0f 02 00 00 00 00 00

00:1a.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI #5 (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 81ec
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at e080 [size=32]
00: 86 80 35 28 05 00 80 02 02 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 81 e0 00 00 00 00 00 00 00 00 00 00 43 10 ec 81
30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 02 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 2f 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 86 0f 02 00 00 00 00 00

00:1a.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI #2 (rev 02) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 81ec
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 0: Memory at ffaff000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
00: 86 80 3a 28 06 00 90 02 02 20 03 0c 00 00 00 00
10: 00 f0 af ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 ec 81
30: 00 00 00 00 50 00 00 00 00 00 00 00 05 03 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 01 58 c2 c9 00 00 00 00 0a 00 a0 20 00 00 00 00
60: 20 20 ff 01 00 00 00 00 01 00 00 00 00 00 08 80
70: 00 00 cf 03 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 aa ff 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 88 85 40 00 86 0f 02 00 06 97 02 20

00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 02)
Subsystem: ASUSTeK Computer Inc. Unknown device 821a
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at ffaf8000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express Unknown type IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed unknown, Width x0, ASPM unknown, Port 0
Link: Latency L0s <64ns, L1 <1us
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed unknown, Width x0
00: 86 80 4b 28 06 00 10 00 02 00 03 04 08 00 00 00
10: 04 80 af ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 1a 82
30: 00 00 00 00 50 00 00 00 00 00 00 00 03 01 00 00
40: 01 00 00 03 00 00 00 00 00 00 00 00 00 00 00 00
50: 01 60 42 c8 00 00 00 00 00 00 00 00 00 00 00 00
60: 05 70 80 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 10 00 91 00 00 00 00 00 00 08 10 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 86 0f 02 00 00 00 00 00

00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 02) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Prefetchable memory behind bridge: 00000000dfe00000-00000000dfefffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x2, ASPM L0s L1, Port 1
Link: Latency L0s <1us, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x0
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee0300c Data: 4161
Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Unknown device 821a
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 86 80 3f 28 06 05 10 00 02 00 04 06 08 00 81 00
10: 00 00 00 00 00 00 00 00 00 03 03 00 f0 00 00 20
20: f0 ff 00 00 e1 df e1 df 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 01 02 00
40: 10 80 41 01 c0 8f 00 00 0f 00 10 00 21 4c 11 01
50: 00 00 01 10 60 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 05 90 01 00 0c 30 e0 fe 61 41 00 00 00 00 00 00
90: 0d a0 00 00 43 10 1a 82 00 00 00 00 00 00 00 00
a0: 01 00 02 c8 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 11 08 00 00 00 00
e0: 00 00 c7 00 06 07 08 00 30 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 86 0f 02 00 00 00 00 00

00:1c.4 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 5 (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: ff800000-ff8fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 5
Link: Latency L0s <256ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee0300c Data: 4169
Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Unknown device 821a
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 86 80 47 28 07 05 10 00 02 00 04 06 08 00 81 00
10: 00 00 00 00 00 00 00 00 00 02 02 00 b0 b0 00 00
20: 80 ff 80 ff f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 01 02 00
40: 10 80 41 01 c0 8f 00 00 0f 00 10 00 11 2c 11 05
50: 40 00 11 30 60 00 00 00 00 00 48 01 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 05 90 01 00 0c 30 e0 fe 69 41 00 00 00 00 00 00
90: 0d a0 00 00 43 10 1a 82 00 00 00 00 00 00 00 00
a0: 01 00 02 c8 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 11 08 00 00 00 00
e0: 00 00 c7 00 06 07 08 00 30 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 86 0f 02 00 00 00 00 00

00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI #1 (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 81ec
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at d800 [size=32]
00: 86 80 30 28 05 00 80 02 02 00 03 0c 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 d8 00 00 00 00 00 00 00 00 00 00 43 10 ec 81
30: 00 00 00 00 00 00 00 00 00 00 00 00 07 01 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 2f 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 86 0f 02 00 00 00 00 00

00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI #2 (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 81ec
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at d880 [size=32]
00: 86 80 31 28 05 00 80 02 02 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 81 d8 00 00 00 00 00 00 00 00 00 00 43 10 ec 81
30: 00 00 00 00 00 00 00 00 00 00 00 00 0f 02 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 2f 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 86 0f 02 00 00 00 00 00

00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI #3 (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 81ec
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at dc00 [size=32]
00: 86 80 32 28 05 00 80 02 02 00 03 0c 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 dc 00 00 00 00 00 00 00 00 00 00 43 10 ec 81
30: 00 00 00 00 00 00 00 00 00 00 00 00 05 03 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 2f 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 86 0f 02 00 00 00 00 00

00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI #1 (rev 02) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 81ec
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at ffafec00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
00: 86 80 36 28 06 00 90 02 02 20 03 0c 00 00 00 00
10: 00 ec af ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 ec 81
30: 00 00 00 00 50 00 00 00 00 00 00 00 07 01 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 01 58 c2 c9 00 00 00 00 0a 00 a0 20 00 00 00 00
60: 20 20 ff 01 00 00 00 00 01 00 00 00 00 00 08 80
70: 00 00 cf 3f 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 aa ff 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 88 85 40 00 86 0f 02 00 06 97 02 20

00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev f2) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: ff900000-ff9fffff
Prefetchable memory behind bridge: 0000000080000000-00000000800fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Subsystem: ASUSTeK Computer Inc. Unknown device 821a
00: 86 80 4e 24 07 01 10 00 f2 01 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 04 04 20 c0 c0 80 22
20: 90 ff 90 ff 01 80 01 80 00 00 00 00 00 00 00 00
30: 00 00 00 00 50 00 00 00 00 00 00 00 ff 00 02 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 12 00 00
50: 0d 00 00 00 43 10 1a 82 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 86 0f 02 00 00 00 00 00

00:1f.0 ISA bridge: Intel Corporation 82801HB/HR (ICH8/R) LPC Interface Controller (rev 02)
Subsystem: ASUSTeK Computer Inc. Unknown device 821a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00: 86 80 10 28 07 00 10 02 02 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 1a 82
30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00
40: 01 08 00 00 80 00 00 00 81 04 00 00 10 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 8b 8a 85 8f d0 00 00 00 80 8e 83 87 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 0f 14 95 02 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 20 06 00 00 39 00 00 00 13 00 00 00 00 03 00 00
b0: 00 00 f0 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 33 22 11 00 67 45 00 00 c0 c0 00 00 00 00 00 00
e0: 09 00 0c 10 21 00 04 ca 60 00 00 00 00 00 00 00
f0: 01 c0 d1 fe 14 19 11 00 86 0f 02 00 00 00 00 00

00:1f.2 SATA controller: Intel Corporation 82801HR/HO/HH (ICH8R/DO/DH) SATA AHCI Controller (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: ASUSTeK Computer Inc. Unknown device 821a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 1276
Region 0: I/O ports at ec00 [size=8]
Region 1: I/O ports at e880 [size=4]
Region 2: I/O ports at e800 [size=8]
Region 3: I/O ports at e480 [size=4]
Region 4: I/O ports at e400 [size=32]
Region 5: Memory at ffaff800 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/4 Enable+
Address: fee0300c Data: 4191
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] #12 [0010]
00: 86 80 24 28 07 04 b0 02 02 01 06 01 00 00 00 00
10: 01 ec 00 00 81 e8 00 00 01 e8 00 00 81 e4 00 00
20: 01 e4 00 00 00 f8 af ff 00 00 00 00 43 10 1a 82
30: 00 00 00 00 80 00 00 00 00 00 00 00 0f 02 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 01 a8 03 40 08 00 00 00 00 00 00 00 00 00 00 00
80: 05 70 09 00 0c 30 e0 fe 91 41 00 00 00 00 00 00
90: 40 00 33 83 80 01 00 00 00 00 00 00 01 00 00 00
a0: 00 00 00 00 00 00 00 00 12 00 10 00 48 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 86 0f 02 00 00 00 00 00

00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 02)
Subsystem: ASUSTeK Computer Inc. Unknown device 821a
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at 80100000 (32-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 0400 [size=32]
00: 86 80 3e 28 03 00 80 02 02 00 05 0c 00 00 00 00
10: 00 00 10 80 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 04 00 00 00 00 00 00 00 00 00 00 43 10 1a 82
30: 00 00 00 00 00 00 00 00 00 00 00 00 0f 03 00 00
40: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 03 04 04 00 00 00 08 08 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 04 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 86 0f 02 00 00 00 00 00

01:00.0 VGA compatible controller: ATI Technologies Inc R480 [Radeon X800 GTO (PCIE)] (prog-if 00 [VGA])
Subsystem: PC Partner Limited Unknown device 1600
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at c0000000 (64-bit, prefetchable) [size=256M]
Region 2: Memory at ff7f0000 (64-bit, non-prefetchable) [size=64K]
Region 4: I/O ports at a000 [size=256]
Expansion ROM at ff7c0000 [disabled] [size=128K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <256ns, L1 <4us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port 0
Link: Latency L0s <256ns, L1 <2us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x16
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
00: 02 10 4f 5d 07 00 10 00 00 00 00 03 08 00 80 00
10: 0c 00 00 c0 00 00 00 00 04 00 7f ff 00 00 00 00
20: 01 a0 00 00 00 00 00 00 00 00 00 00 4b 17 00 16
30: 00 00 7c ff 50 00 00 00 00 00 00 00 0b 01 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 4b 17 00 16
50: 01 58 02 06 00 00 00 00 10 80 01 00 a0 04 00 00
60: 10 08 00 00 01 ad 00 00 40 00 01 11 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 05 00 80 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

01:00.1 Display controller: ATI Technologies Inc R480 [Radeon X800 GTO (PCIE)] (Secondary)
Subsystem: PC Partner Limited Unknown device 1601
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Region 0: Memory at ff7e0000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <256ns, L1 <4us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port 0
Link: Latency L0s <256ns, L1 <2us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x16
00: 02 10 6f 5d 07 00 10 00 00 00 80 03 08 00 00 00
10: 04 00 7e ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 4b 17 01 16
30: 00 00 00 00 50 00 00 00 00 00 00 00 ff 00 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 01 58 02 06 00 00 00 00 10 00 01 00 80 04 00 00
60: 00 00 00 00 01 ad 00 00 00 00 01 11 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

02:00.0 SATA controller: JMicron Technologies, Inc. JMicron 20360/20363 AHCI Controller (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: ASUSTeK Computer Inc. Unknown device 81e4
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 5: Memory at ff8fe000 (32-bit, non-prefetchable) [size=8K]
Expansion ROM at ff8e0000 [disabled] [size=64K]
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Express Legacy Endpoint IRQ 1
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s, Port 1
Link: Latency L0s <1us, L1 <16us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
00: 7b 19 63 23 07 00 10 00 02 01 06 01 08 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 e0 8f ff 00 00 00 00 43 10 e4 81
30: 00 00 8e ff 68 00 00 00 00 00 00 00 0b 01 00 00
40: b3 a1 c2 80 08 dc ff f1 20 00 00 24 03 00 00 00
50: 10 00 11 02 00 00 00 00 00 20 08 00 11 44 02 01
60: 40 00 11 10 00 00 00 00 01 50 02 40 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 08 08 00 00 a0 01 0a 00 0f aa 0f aa 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80
c0: c3 8b 38 00 03 45 02 00 9c 34 27 c0 49 86 00 00
d0: 18 00 80 80 01 00 00 00 01 00 eb 00 00 00 00 15
e0: 00 00 00 00 00 00 00 00 9c 34 27 c0 49 42 00 89
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

02:00.1 IDE interface: JMicron Technologies, Inc. JMicron 20360/20363 AHCI Controller (rev 02) (prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc. Unknown device 81e4
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at bc00 [size=8]
Region 1: I/O ports at b880 [size=4]
Region 2: I/O ports at b800 [size=8]
Region 3: I/O ports at b480 [size=4]
Region 4: I/O ports at b400 [size=16]
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 7b 19 63 23 05 00 10 00 02 85 01 01 00 00 00 00
10: 01 bc 00 00 81 b8 00 00 01 b8 00 00 81 b4 00 00
20: 01 b4 00 00 00 00 00 00 00 00 00 00 43 10 e4 81
30: 00 00 00 00 68 00 00 00 00 00 00 00 00 02 00 00
40: b3 a1 c2 80 08 dc ff f1 20 00 00 24 03 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 01 00 02 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 08 08 00 00 a0 01 0a 00 0f aa 0f aa 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80
c0: c3 8b 38 00 03 45 02 00 9c 34 27 c0 49 86 00 00
d0: 18 00 80 80 01 00 00 00 01 00 eb 00 00 00 00 15
e0: 00 00 00 00 00 00 00 00 9c 34 27 c0 49 42 00 89
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

04:00.0 Class ff00: Measurement Computing PCI-DAS6025 (rev 02)

	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64, Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 14
	Region 0: Memory at ff9ffc00 (32-bit, non-prefetchable) [size=256]
	Region 1: I/O ports at c800 [size=256]
	Region 2: Memory at ff9fe000 (32-bit, non-prefetchable) [size=4K]
	Region 3: Memory at ff9fd000 (32-bit, non-prefetchable) [size=4K]

00: 07 13 5e 00 17 00 80 02 02 00 00 ff 08 40 00 00 10: 00 fc 9f ff 01 c8 00 00 00 e0 9f ff 00 d0 9f ff 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 0e 01 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

04:01.0 Multimedia controller: Philips Semiconductors SAA7146 (rev 01)
Subsystem: Technotrend Systemtechnik GmbH Technotrend/Hauppauge DVB card rev2.1
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (3750ns min, 9500ns max)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at ff9ff800 (32-bit, non-prefetchable) [size=512]
00: 31 11 46 71 06 00 80 02 01 00 80 04 00 40 00 00
10: 00 f8 9f ff 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 c2 13 03 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 03 01 0f 26
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 80 00 00 00 80 00 00 00 80 00 00 00 80
90: 00 00 00 80 00 00 00 80 00 00 00 80 00 00 00 80
a0: 00 00 00 80 00 00 00 80 00 00 00 80 00 00 00 80
b0: 00 00 00 80 00 00 00 80 00 00 00 80 00 00 00 80
c0: 00 00 00 80 00 00 00 80 00 00 00 80 00 00 00 80
d0: 00 00 00 80 00 00 00 80 00 00 00 80 00 00 00 80
e0: 00 00 00 80 00 00 00 80 00 00 00 80 00 00 00 80
f0: 00 00 00 80 00 00 00 80 00 00 00 80 00 00 00 80

04:03.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev c0) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 81fe
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at ff9ff000 (32-bit, non-prefetchable) [size=2K]
Region 1: I/O ports at cc00 [size=128]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 44 30 17 00 10 02 c0 10 00 0c 08 40 00 00
10: 00 f0 9f ff 01 cc 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 fe 81
30: 00 00 00 00 50 00 00 00 00 00 00 00 0e 01 00 20
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 01 00 02 e4 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

04:04.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001 Gigabit Ethernet Controller (rev 14)
Subsystem: ASUSTeK Computer Inc. Marvell 88E8001 Gigabit Ethernet Controller (Asus)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 19
Region 0: Memory at ff9f8000 (32-bit, non-prefetchable) [size=16K]
Region 1: I/O ports at c400 [size=256]
Expansion ROM at 80000000 [disabled] [size=128K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
00: ab 11 20 43 13 00 b0 02 14 00 00 02 08 40 00 00
10: 00 80 9f ff 01 c4 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 1a 81
30: 00 00 9c ff 48 00 00 00 00 00 00 00 0f 01 17 1f
40: 00 00 f0 05 00 80 a0 01 01 50 02 fe 00 20 00 13
50: 03 00 00 80 00 00 00 01 00 00 04 01 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Stephen Hemminger

2007-09-11 12:36 UTC #3 lore raw

Quoted 16 lines · On Tue, 11 Sep 2007 12:58:24 +0200 Jan Gukelberger <[email protected]> wrote:

Quoted 2 lines · Stephen Hemminger
On Fri, 07 Sep 2007 18:42:35 +0200
Jan Gukelberger <[email protected]> wrote:
[...]
Quoted 11 lines
Quoted 9 lines
The key problem seem to be the following lines in dmesg:
------------------------------------------------------------------------
ACPI: PCI Interrupt 0000:04:04.0[A] -> GSI 19 (level, low) -> IRQ 19
PCI: Unable to reserve mem region #1:4000@ff9f8000 for device 0000:04:04.0 skge 0000:04:04.0: cannot obtain PCI resources
ACPI: PCI interrupt for device 0000:04:04.0 disabled
skge: probe of 0000:04:04.0 failed with error -16
------------------------------------------------------------------------
There is some kind of device conflict, please provide lspci -vvvxx output.

Quoted 8 lines

I'm attaching the output of 'lspci -vvvxx' on the working 2.6.20 kernel as well as the output of 'lspci -vvxxx' on 2.6.23-rc5 which I recorded earlier.
I you specifically need 'lspci -vvvxx' on 2.6.23-rc5 please drop me a note and I'll reboot quickly.
Thanks,
Jan

All looks in order, on the PCI tables. There is a firewire control just above the skge device, perhaps you enabled one of the firewire stacks in the configuration? Perhaps the console (dmesg) output will show some clue.

Jan Gukelberger

author

2007-09-11 13:39 UTC #4 lore raw

Quoted 25 lines · Stephen Hemminger

Quoted 22 lines · On Tue, 11 Sep 2007 12:58:24 +0200 Jan Gukelberger <[email protected]> wrote:
Quoted 2 lines · Stephen Hemminger
On Fri, 07 Sep 2007 18:42:35 +0200
Jan Gukelberger <[email protected]> wrote:
[...]
Quoted 11 lines
Quoted 9 lines
The key problem seem to be the following lines in dmesg:
------------------------------------------------------------------------
ACPI: PCI Interrupt 0000:04:04.0[A] -> GSI 19 (level, low) -> IRQ 19
PCI: Unable to reserve mem region #1:4000@ff9f8000 for device 0000:04:04.0 skge 0000:04:04.0: cannot obtain PCI resources
ACPI: PCI interrupt for device 0000:04:04.0 disabled
skge: probe of 0000:04:04.0 failed with error -16
------------------------------------------------------------------------
There is some kind of device conflict, please provide lspci -vvvxx output.
I'm attaching the output of 'lspci -vvvxx' on the working 2.6.20 kernel as well as the output of 'lspci -vvxxx' on 2.6.23-rc5 which I recorded earlier.
I you specifically need 'lspci -vvvxx' on 2.6.23-rc5 please drop me a note and I'll reboot quickly.

Quoted 6 lines

Quoted 2 lines
Thanks,
Jan
All looks in order, on the PCI tables. There is a firewire control just above the skge device, perhaps you enabled one of the firewire stacks in the configuration?

I did a quick diff of the respective kernel .config's (this is the configuration you mean, right?) and haven't found any notable differences in the firewire options.

Quoted 1 line

Perhaps the console (dmesg) output will show some clue.

I'm attaching a diff between dmesg of a working and a non-working boot. You can find the full dmesg records in my first mail and in the Debian BTS respectively.

The only thing I can see there is the old kernel having some problems with the SATA controller - even though I did never notice any unusual behaviour apart from these messages:
------------------------------------------------------------------------
PCI: Device 0000:02:00.0 not available because of resource collisions
ahci: probe of 0000:02:00.0 failed with error -22
JMB363: IDE controller at PCI slot 0000:02:00.0
PCI: Device 0000:02:00.0 not available because of resource collisions
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
JMB363: BIOS configuration fixed.
------------------------------------------------------------------------

Don't know whether this could be related?

Thanks,
Jan

dmesg-2.6.23-rc5 renamed from home/jan/dmesg-2.6.20 +154 ~~-147~~

@@ -1,4 +1,4 @@
-Linux version 2.6.20-1-amd64 (Debian 2.6.20-3) ([email protected]) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP Tue Apr 24 21:10:58 UTC 2007
+Linux version 2.6.23-rc5-amd64 (Debian 2.6.23~rc5-1~experimental.1~snapshot.9462) ([email protected]) (gcc version 4.1.3 20070718 (prerelease) (Debian 4.1.2-14+1)) #1 SMP Thu Sep 6 06:18:52 UTC 2007
 Command line: root=/dev/sda6 ro quiet vga=791 
 BIOS-provided physical RAM map:
  BIOS-e820: 0000000000000000 - 000000000009ec00 (usable)

@@ -14,18 +14,19 @@
 Entering add_active_range(0, 256, 520080) 1 entries of 3200 used
 end_pfn_map = 1048576
 DMI 2.4 present.
-ACPI: RSDP (v002 ACPIAM                                ) @ 0x00000000000fad70
-ACPI: XSDT (v001 NEC             0x05000730 MSFT 0x00000097) @ 0x000000007ef90100
-ACPI: FADT (v003 MSTEST OEMFACP  0x05000730 MSFT 0x00000097) @ 0x000000007ef90290
-ACPI: MADT (v001 MSTEST OEMAPIC  0x05000730 MSFT 0x00000097) @ 0x000000007ef90390
-ACPI: MCFG (v001 MSTEST OEMMCFG  0x05000730 MSFT 0x00000097) @ 0x000000007ef90400
-ACPI: SLIC (v001 NEC             0x05000730 MSFT 0x00000097) @ 0x000000007ef90440
-ACPI: OEMB (v001 MSTEST AMI_OEM  0x05000730 MSFT 0x00000097) @ 0x000000007ef9e040
-ACPI: HPET (v001 MSTEST OEMHPET  0x05000730 MSFT 0x00000097) @ 0x000000007ef9a250
-ACPI: GSCI (v001 MSTEST GMCHSCI  0x05000730 MSFT 0x00000097) @ 0x000000007ef9e0c0
-ACPI: SSDT (v001    AMI   CPU1PM 0x00000001 INTL 0x20060113) @ 0x000000007efa00f0
-ACPI: SSDT (v001    AMI   CPU2PM 0x00000001 INTL 0x20060113) @ 0x000000007efa02b0
-ACPI: DSDT (v001  A0579 A0579000 0x00000000 INTL 0x20060113) @ 0x0000000000000000
+ACPI: RSDP 000FAD70, 0024 (r2 ACPIAM)
+ACPI: XSDT 7EF90100, 006C (r1 NEC              5000730 MSFT       97)
+ACPI: FACP 7EF90290, 00F4 (r3 MSTEST OEMFACP   5000730 MSFT       97)
+ACPI: DSDT 7EF905C0, 9C85 (r1  A0579 A0579000        0 INTL 20060113)
+ACPI: FACS 7EF9E000, 0040
+ACPI: APIC 7EF90390, 006C (r1 MSTEST OEMAPIC   5000730 MSFT       97)
+ACPI: MCFG 7EF90400, 003C (r1 MSTEST OEMMCFG   5000730 MSFT       97)
+ACPI: SLIC 7EF90440, 0176 (r1 NEC              5000730 MSFT       97)
+ACPI: OEMB 7EF9E040, 007B (r1 MSTEST AMI_OEM   5000730 MSFT       97)
+ACPI: HPET 7EF9A250, 0038 (r1 MSTEST OEMHPET   5000730 MSFT       97)
+ACPI: GSCI 7EF9E0C0, 2024 (r1 MSTEST GMCHSCI   5000730 MSFT       97)
+ACPI: SSDT 7EFA00F0, 01BF (r1    AMI   CPU1PM        1 INTL 20060113)
+ACPI: SSDT 7EFA02B0, 0133 (r1    AMI   CPU2PM        1 INTL 20060113)
 No NUMA configuration found
 Faking a node at 0000000000000000-000000007ef90000
 Entering add_active_range(0, 0, 158) 0 entries of 3200 used

@@ -35,16 +36,18 @@
   DMA             0 ->     4096
   DMA32        4096 ->  1048576
   Normal    1048576 ->  1048576
+Movable zone start PFN for each node
 early_node_map[2] active PFN ranges
     0:        0 ->      158
     0:      256 ->   520080
 On node 0 totalpages: 519982
   DMA zone: 56 pages used for memmap
-  DMA zone: 972 pages reserved
-  DMA zone: 2970 pages, LIFO batch:0
+  DMA zone: 1044 pages reserved
+  DMA zone: 2898 pages, LIFO batch:0
   DMA32 zone: 7054 pages used for memmap
   DMA32 zone: 508930 pages, LIFO batch:31
   Normal zone: 0 pages used for memmap
+  Movable zone: 0 pages used for memmap
 ACPI: PM-Timer IO Port: 0x808
 ACPI: Local APIC address 0xfee00000
 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)

@@ -60,31 +63,35 @@
 ACPI: IRQ0 used by override.
 ACPI: IRQ2 used by override.
 ACPI: IRQ9 used by override.
-Setting APIC routing to physical flat
+Setting APIC routing to flat
 ACPI: HPET id: 0x8086a202 base: 0xfed00000
 Using ACPI (MADT) for SMP configuration information
-Nosave address range: 000000000009e000 - 000000000009f000
-Nosave address range: 000000000009f000 - 00000000000a0000
-Nosave address range: 00000000000a0000 - 00000000000e4000
-Nosave address range: 00000000000e4000 - 0000000000100000
+swsusp: Registered nosave memory region: 000000000009e000 - 000000000009f000
+swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
+swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e4000
+swsusp: Registered nosave memory region: 00000000000e4000 - 0000000000100000
 Allocating PCI resources starting at 80000000 (gap: 7f000000:7fe00000)
 SMP: Allowing 4 CPUs, 2 hotplug CPUs
-PERCPU: Allocating 36992 bytes of per cpu data
-Built 1 zonelists.  Total pages: 511900
+PERCPU: Allocating 35176 bytes of per cpu data
+Built 1 zonelists in Node order.  Total pages: 511828
+Policy zone: DMA32
 Kernel command line: root=/dev/sda6 ro quiet vga=791 
 Initializing CPU#0
 PID hash table entries: 4096 (order: 12, 32768 bytes)
+Extended CMOS year: 2000
+time.c: Detected 2399.997 MHz processor.
 Console: colour dummy device 80x25
-Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
-Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
+console [tty0] enabled
 Checking aperture...
 Calgary: detecting Calgary via BIOS EBDA area
 Calgary: Unable to locate Rio Grande table in EBDA - bailing!
-Memory: 2038324k/2080320k available (1970k kernel code, 41604k reserved, 920k data, 284k init)
-Calibrating delay using timer specific routine.. 4804.04 BogoMIPS (lpj=9608092)
+Memory: 2041096k/2080320k available (2066k kernel code, 38832k reserved, 977k data, 304k init)
+Calibrating delay using timer specific routine.. 4803.34 BogoMIPS (lpj=9606690)
 Security Framework v1.0.0 initialized
 SELinux:  Disabled at boot.
 Capability LSM initialized
+Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
+Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
 Mount-cache hash table entries: 256
 CPU: L1 I cache: 32K, L1 D cache: 32K
 CPU: L2 cache: 4096K

@@ -94,14 +101,14 @@
 CPU: Processor Core ID: 0
 CPU0: Thermal monitoring enabled (TM2)
 SMP alternatives: switching to UP code
-ACPI: Core revision 20060707
+ACPI: Core revision 20070126
 Using local APIC timer interrupts.
-result 16666675
+result 16666629
 Detected 16.666 MHz APIC timer.
 SMP alternatives: switching to SMP code
 Booting processor 1/2 APIC 0x1
 Initializing CPU#1
-Calibrating delay using timer specific routine.. 4800.01 BogoMIPS (lpj=9600034)
+Calibrating delay using timer specific routine.. 4800.03 BogoMIPS (lpj=9600060)
 CPU: L1 I cache: 32K, L1 D cache: 32K
 CPU: L2 cache: 4096K
 CPU 1/1 -> Node 0

@@ -109,25 +116,20 @@
 CPU: Processor Core ID: 1
 CPU1: Thermal monitoring enabled (TM2)
 Intel(R) Core(TM)2 CPU          6600  @ 2.40GHz stepping 06
+checking TSC synchronization [CPU#0 -> CPU#1]: passed.
 Brought up 2 CPUs
-testing NMI watchdog ... OK.
-time.c: Using 14.318180 MHz WALL HPET GTOD HPET/TSC timer.
-time.c: Detected 2400.003 MHz processor.
-migration_cost=20
 NET: Registered protocol family 16
 ACPI: bus type pci registered
 PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
 PCI: Not using MMCONFIG.
 PCI: Using configuration type 1
+ACPI: EC: Look up EC in DSDT
 ACPI: Interpreter enabled
+ACPI: (supports S0 S1 S3)
 ACPI: Using IOAPIC for interrupt routing
 ACPI: PCI Root Bridge [PCI0] (0000:00)
-PCI: Probing PCI hardware (bus 00)
 PCI quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
 PCI quirk: region 0480-04bf claimed by ICH6 GPIO
-Boot video device is 0000:01:00.0
-0000:02:00.0: cannot adjust BAR2 (not I/O)
-0000:02:00.0: cannot adjust BAR3 (not I/O)
 PCI: Transparent bridge - 0000:00:1e.0
 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]

@@ -142,8 +144,10 @@
 ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 *14 15)
 ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 5 6 7 10 11 12 14 15)
 ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 10 11 12 14 15)
+ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] -  CD, should be C4 [20070126]
 Linux Plug and Play Support v0.97 (c) Adam Belay
 pnp: PnP ACPI init
+ACPI: bus type pnp registered
 pnp: ACPI device : hid PNP0A08
 pnp: ACPI device : hid PNP0C01
 pnp: ACPI device : hid PNP0200

@@ -161,26 +165,39 @@
 pnp: ACPI device : hid PNP0C02
 pnp: ACPI device : hid PNP0C01
 pnp: PnP ACPI: found 16 devices
+ACPI: ACPI bus type pnp unregistered
 usbcore: registered new interface driver usbfs
 usbcore: registered new interface driver hub
 usbcore: registered new device driver usb
 PCI: Using ACPI for IRQ routing
 PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
-PCI: Cannot allocate resource region 2 of device 0000:02:00.0
-PCI: Cannot allocate resource region 3 of device 0000:02:00.0
 NET: Registered protocol family 8
 NET: Registered protocol family 20
+PCI-GART: No AMD northbridge found.
 hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
 hpet0: 3 64-bit timers, 14318180 Hz
-PCI-GART: No AMD northbridge found.
+ACPI: RTC can wake from S4
+Time: tsc clocksource has been installed.
 pnp: the driver 'system' has been registered
 pnp: match found with the PnP device '00:01' and the driver 'system'
+pnp: 00:01: iomem range 0xfed14000-0xfed19fff has been reserved
 pnp: match found with the PnP device '00:08' and the driver 'system'
 pnp: 00:08: ioport range 0x290-0x297 has been reserved
 pnp: match found with the PnP device '00:09' and the driver 'system'
+pnp: 00:09: iomem range 0xfed1c000-0xfed1ffff has been reserved
+pnp: 00:09: iomem range 0xfed20000-0xfed8ffff has been reserved
+pnp: 00:09: iomem range 0xff9fa000-0xff9fafff has been reserved
+pnp: 00:09: iomem range 0xfff00000-0xfffffffe could not be reserved
 pnp: match found with the PnP device '00:0b' and the driver 'system'
+pnp: 00:0b: iomem range 0xfec00000-0xfec00fff has been reserved
+pnp: 00:0b: iomem range 0xfee00000-0xfee00fff could not be reserved
 pnp: match found with the PnP device '00:0e' and the driver 'system'
+pnp: 00:0e: iomem range 0xe0000000-0xefffffff has been reserved
 pnp: match found with the PnP device '00:0f' and the driver 'system'
+pnp: 00:0f: iomem range 0x0-0x9ffff could not be reserved
+pnp: 00:0f: iomem range 0xc0000-0xcffff has been reserved
+pnp: 00:0f: iomem range 0xe0000-0xfffff could not be reserved
+pnp: 00:0f: iomem range 0x100000-0x7effffff could not be reserved
 PCI: Bridge: 0000:00:01.0
   IO window: 8000-afff
   MEM window: ff700000-ff7fffff

@@ -206,20 +223,21 @@
 PCI: Setting latency timer of device 0000:00:1e.0 to 64
 NET: Registered protocol family 2
 IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
-TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
+TCP established hash table entries: 262144 (order: 10, 6291456 bytes)
 TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
 TCP: Hash tables configured (established 262144 bind 65536)
 TCP reno registered
 checking if image is initramfs... it is
-Freeing initrd memory: 5937k freed
+Freeing initrd memory: 5950k freed
 audit: initializing netlink socket (disabled)
-audit(1181990747.912:1): initialized
+audit(1189181505.780:1): initialized
 VFS: Disk quotas dquot_6.5.1
 Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
 io scheduler noop registered
 io scheduler anticipatory registered
 io scheduler deadline registered
 io scheduler cfq registered (default)
+Boot video device is 0000:01:00.0
 PCI: Setting latency timer of device 0000:00:01.0 to 64
 assign_interrupt_mode Found MSI capability
 Allocate Port Service[0000:00:01.0:pcie00]

@@ -231,7 +249,7 @@
 assign_interrupt_mode Found MSI capability
 Allocate Port Service[0000:00:1c.4:pcie00]
 Allocate Port Service[0000:00:1c.4:pcie02]
-vesafb: framebuffer at 0xc0000000, mapped to 0xffffc20000080000, using 3072k, total 16384k
+vesafb: framebuffer at 0xc0000000, mapped to 0xffffc20000b00000, using 3072k, total 16384k
 vesafb: mode is 1024x768x16, linelength=2048, pages=9
 vesafb: scrolling: redraw
 vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0

@@ -239,7 +257,7 @@
 fb0: VESA VGA frame buffer device
 Real Time Clock Driver v1.12ac
 hpet_resources: 0xfed00000 is busy
-Linux agpgart interface v0.101 (c) Dave Jones
+Linux agpgart interface v0.102
 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
 serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
 pnp: the driver 'serial' has been registered

@@ -257,11 +275,10 @@
 TCP bic registered
 NET: Registered protocol family 1
 NET: Registered protocol family 17
-ACPI: (supports S0 S1 S3 S4 S5)
-Freeing unused kernel memory: 284k freed
+Freeing unused kernel memory: 304k freed
 input: AT Translated Set 2 keyboard as /class/input/input0
-ACPI Exception (acpi_processor-0677): AE_NOT_FOUND, Processor Device is not present [20060707]
-ACPI Exception (acpi_processor-0677): AE_NOT_FOUND, Processor Device is not present [20060707]
+ACPI Exception (processor_core-0797): AE_NOT_FOUND, Processor Device is not present [20070126]
+ACPI Exception (processor_core-0797): AE_NOT_FOUND, Processor Device is not present [20070126]
 USB Universal Host Controller Interface driver v3.0
 ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 16
 PCI: Setting latency timer of device 0000:00:1a.0 to 64

@@ -274,10 +291,9 @@
 Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
 pnp: the driver 'ide' has been registered
-SCSI subsystem initialized
-ieee1394: Initialized config rom entry `ip1394'
 Floppy drive(s): fd0 is 1.44M
-libata version 2.00 loaded.
+SCSI subsystem initialized
+libata version 2.21 loaded.
 FDC 0 is a post-1991 82077
 ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 17 (level, low) -> IRQ 17
 PCI: Setting latency timer of device 0000:00:1a.1 to 64

@@ -312,8 +328,42 @@
 hub 5-0:1.0: USB hub found
 hub 5-0:1.0: 2 ports detected
 ACPI: PCI Interrupt 0000:04:04.0[A] -> GSI 19 (level, low) -> IRQ 19
-skge 1.9 addr 0xff9f8000 irq 19 chip Yukon-Lite rev 9
-skge eth0: addr 00:18:f3:90:8e:7b
+PCI: Unable to reserve mem region #1:4000@ff9f8000 for device 0000:04:04.0
+skge 0000:04:04.0: cannot obtain PCI resources
+ACPI: PCI interrupt for device 0000:04:04.0 disabled
+skge: probe of 0000:04:04.0 failed with error -16
+ACPI: PCI Interrupt 0000:04:03.0[A] -> GSI 21 (level, low) -> IRQ 21
+firewire_ohci: Added fw-ohci device 0000:04:03.0, OHCI version 1.10
+ahci 0000:00:1f.2: version 2.3
+ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
+firewire_core: created new fw device fw0 (0 config rom retries, S400)
+ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0x33 impl SATA mode
+ahci 0000:00:1f.2: flags: 64bit ncq sntf ilck stag pm led clo pmp pio slum part 
+PCI: Setting latency timer of device 0000:00:1f.2 to 64
+scsi0 : ahci
+scsi1 : ahci
+scsi2 : ahci
+scsi3 : ahci
+scsi4 : ahci
+scsi5 : ahci
+ata1: SATA max UDMA/133 cmd 0xffffc20000ac2900 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 1276
+ata2: SATA max UDMA/133 cmd 0xffffc20000ac2980 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 1276
+ata3: DUMMY
+ata4: DUMMY
+ata5: SATA max UDMA/133 cmd 0xffffc20000ac2b00 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 1276
+ata6: SATA max UDMA/133 cmd 0xffffc20000ac2b80 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 1276
+ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
+ata1.00: ATA-7: SAMSUNG HD401LJ, ZZ100-15, max UDMA7
+ata1.00: 781422768 sectors, multi 0: LBA48 NCQ (not used)
+ata1.00: configured for UDMA/133
+ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
+ata2.00: ATAPI: HL-DT-STDVD-RAM GSA-H30N, 1.01, max UDMA/100
+ata2.00: configured for UDMA/100
+ata5: SATA link down (SStatus 0 SControl 300)
+ata6: SATA link down (SStatus 0 SControl 300)
+scsi 0:0:0:0: Direct-Access     ATA      SAMSUNG HD401LJ  ZZ10 PQ: 0 ANSI: 5
+scsi 1:0:0:0: CD-ROM            HL-DT-ST DVD-RAM GSA-H30N 1.01 PQ: 0 ANSI: 5
+ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
 ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 18
 PCI: Setting latency timer of device 0000:00:1a.7 to 64
 ehci_hcd 0000:00:1a.7: EHCI Host Controller

@@ -325,6 +375,15 @@
 usb usb6: configuration #1 chosen from 1 choice
 hub 6-0:1.0: USB hub found
 hub 6-0:1.0: 4 ports detected
+ahci 0000:02:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
+ahci 0000:02:00.0: flags: 64bit ncq pm led clo pmp pio slum part 
+PCI: Setting latency timer of device 0000:02:00.0 to 64
+scsi6 : ahci
+scsi7 : ahci
+ata7: SATA max UDMA/133 cmd 0xffffc20000ac4100 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 16
+ata8: SATA max UDMA/133 cmd 0xffffc20000ac4180 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 16
+ata7: SATA link down (SStatus 0 SControl 300)
+ata8: SATA link down (SStatus 0 SControl 300)
 ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
 PCI: Setting latency timer of device 0000:00:1d.7 to 64
 ehci_hcd 0000:00:1d.7: EHCI Host Controller

@@ -336,114 +395,69 @@
 usb usb7: configuration #1 chosen from 1 choice
 hub 7-0:1.0: USB hub found
 hub 7-0:1.0: 6 ports detected
-ACPI: PCI Interrupt 0000:04:03.0[A] -> GSI 21 (level, low) -> IRQ 21
-ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[21]  MMIO=[ff9ff000-ff9ff7ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
-ahci 0000:00:1f.2: version 2.0
-ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
-PCI: Setting latency timer of device 0000:00:1f.2 to 64
-ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0x33 impl SATA mode
-ahci 0000:00:1f.2: flags: 64bit ncq ilck stag pm led clo pmp pio slum part 
-ata1: SATA max UDMA/133 cmd 0xFFFFC20000056900 ctl 0x0 bmdma 0x0 irq 1276
-ata2: SATA max UDMA/133 cmd 0xFFFFC20000056980 ctl 0x0 bmdma 0x0 irq 1276
-ata3: DUMMY
-ata4: DUMMY
-ata5: SATA max UDMA/133 cmd 0xFFFFC20000056B00 ctl 0x0 bmdma 0x0 irq 1276
-ata6: SATA max UDMA/133 cmd 0xFFFFC20000056B80 ctl 0x0 bmdma 0x0 irq 1276
-scsi0 : ahci
-ieee1394: Host added: ID:BUS[0-00:1023]  GUID[0011d80000ec51d2]
-ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
-ata1.00: ATA-7, max UDMA7, 781422768 sectors: LBA48 NCQ (depth 31/32)
-ata1.00: configured for UDMA/133
-scsi1 : ahci
-ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
-ata2.00: ATAPI, max UDMA/100
-ata2.00: configured for UDMA/100
-scsi2 : ahci
-scsi3 : ahci
-scsi4 : ahci
-ata5: SATA link down (SStatus 0 SControl 300)
-scsi5 : ahci
-ata6: SATA link down (SStatus 0 SControl 300)
-scsi 0:0:0:0: Direct-Access     ATA      SAMSUNG HD401LJ  ZZ10 PQ: 0 ANSI: 5
-scsi 1:0:0:0: CD-ROM            HL-DT-ST DVD-RAM GSA-H30N 1.01 PQ: 0 ANSI: 5
-PCI: Device 0000:02:00.0 not available because of resource collisions
-ahci: probe of 0000:02:00.0 failed with error -22
-JMB363: IDE controller at PCI slot 0000:02:00.0
-PCI: Device 0000:02:00.0 not available because of resource collisions
-ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
-JMB363: BIOS configuration fixed.
+sd 0:0:0:0: [sda] 781422768 512-byte hardware sectors (400088 MB)
+sd 0:0:0:0: [sda] Write Protect is off
+sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
+sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
+sd 0:0:0:0: [sda] 781422768 512-byte hardware sectors (400088 MB)
+sd 0:0:0:0: [sda] Write Protect is off
+sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
+sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
+ sda: sda1 sda2 sda3 < sda5 sda6 sda7 >
+sd 0:0:0:0: [sda] Attached SCSI disk
+JMB363: IDE controller at PCI slot 0000:02:00.1
+PCI: Enabling device 0000:02:00.1 (0000 -> 0001)
+ACPI: PCI Interrupt 0000:02:00.1[B] -> GSI 17 (level, low) -> IRQ 17
 JMB363: chipset revision 2
-JMB363: 100% native mode on irq 16
-JMB363: dma_base is invalid
-ide0: JMB363 Bus-Master DMA disabled (BIOS)
-JMB363: dma_base is invalid
-ide1: JMB363 Bus-Master DMA disabled (BIOS)
+JMB363: 100% native mode on irq 17
+PCI: Setting latency timer of device 0000:02:00.1 to 64
+    ide0: BM-DMA at 0xb400-0xb407, BIOS settings: hda:DMA, hdb:DMA
+    ide1: BM-DMA at 0xb408-0xb40f, BIOS settings: hdc:pio, hdd:pio
 Probing IDE interface ide0...
-SCSI device sda: 781422768 512-byte hdwr sectors (400088 MB)
-sda: Write Protect is off
-sda: Mode Sense: 00 3a 00 00
-SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
-SCSI device sda: 781422768 512-byte hdwr sectors (400088 MB)
-sda: Write Protect is off
-sda: Mode Sense: 00 3a 00 00
-SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
- sda: sda1 sda2 sda3 < sda5 sda6 >
-sd 0:0:0:0: Attached scsi disk sda
 sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
 Uniform CD-ROM driver Revision: 3.20
 sr 1:0:0:0: Attached scsi CD-ROM sr0
 sd 0:0:0:0: Attached scsi generic sg0 type 0
 sr 1:0:0:0: Attached scsi generic sg1 type 5
+hdb: WDC WD400BB-00AUA1, ATA DISK drive
+hdb: selected mode 0x45
+ide0 at 0xbc00-0xbc07,0xb882 on irq 17
 Probing IDE interface ide1...
-JMB363: IDE controller at PCI slot 0000:02:00.1
-PCI: Enabling device 0000:02:00.1 (0000 -> 0001)
-ACPI: PCI Interrupt 0000:02:00.1[B] -> GSI 17 (level, low) -> IRQ 17
-JMB363: chipset revision 2
-JMB363: 100% native mode on irq 17
-PCI: Setting latency timer of device 0000:02:00.1 to 64
-    ide2: BM-DMA at 0xb400-0xb407, BIOS settings: hde:DMA, hdf:DMA
-    ide3: BM-DMA at 0xb408-0xb40f, BIOS settings: hdg:pio, hdh:pio
-Probing IDE interface ide2...
-hdf: WDC WD400BB-00AUA1, ATA DISK drive
-hdf: hw_config=6b00
-hdf: hw_config=6b00
-ide2 at 0xbc00-0xbc07,0xb882 on irq 17
-Probing IDE interface ide3...
-hdf: max request size: 128KiB
-hdf: 78165360 sectors (40020 MB) w/2048KiB Cache, CHS=65535/16/63<6>hdf: hw_config=6b00
-, UDMA(100)
-hdf: cache flushes not supported
- hdf: hdf1 hdf2 < hdf5 hdf6 hdf7 hdf8 hdf9 hdf10 hdf11 >
+hdb: max request size: 128KiB
+hdb: 78165360 sectors (40020 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
+hdb: cache flushes not supported
+ hdb: hdb1 hdb2 < hdb5 hdb6 hdb7 hdb8 hdb9 hdb10 hdb11 >
 kjournald starting.  Commit interval 5 seconds
 EXT3-fs: mounted filesystem with ordered data mode.
-eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
-PCI: Enabling device 0000:00:1f.3 (0001 -> 0003)
-ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 18 (level, low) -> IRQ 18
-agpgart: Detected an Intel 965G Chipset.
-agpgart: AGP aperture is 256M @ 0x0
-iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (11-Nov-2006)
+input: PC Speaker as /class/input/input1
+iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
 iTCO_wdt: Found a ICH8 or ICH8R TCO device (Version=2, TCOBASE=0x0860)
 iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
-input: PC Speaker as /class/input/input1
+input: Power Button (FF) as /class/input/input2
+ACPI: Power Button (FF) [PWRF]
+input: Power Button (CM) as /class/input/input3
+ACPI: Power Button (CM) [PWRB]
+ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
+PCI: Setting latency timer of device 0000:00:1b.0 to 64
+hda_codec: Unknown model for AD1988, trying auto-probe from BIOS...
 Linux video capture interface: v2.00
+PCI: Enabling device 0000:00:1f.3 (0001 -> 0003)
+ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 18 (level, low) -> IRQ 18
 logips2pp: Detected unknown logitech mouse model 95
 saa7146: register extension 'dvb'.
 ACPI: PCI Interrupt 0000:04:01.0[A] -> GSI 22 (level, low) -> IRQ 22
-saa7146: found saa7146 @ mem ffffc2000039c800 (revision 1, irq 22) (0x13c2,0x0003).
-DVB: registering new adapter (Technotrend/Hauppauge WinTV Nexus-S rev2.X).
-ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
-PCI: Setting latency timer of device 0000:00:1b.0 to 64
+saa7146: found saa7146 @ mem ffffc20000ace800 (revision 1, irq 22) (0x13c2,0x0003).
+DVB: registering new adapter (Technotrend/Hauppauge WinTV Nexus-S rev2.X)
 adapter has MAC addr = 00:d0:5c:22:68:cc
 dvb-ttpci: gpioirq unknown type=0 len=0
 dvb-ttpci: info @ card 0: firm f0240009, rtsl b0250018, vid 71010068, app 80002622
 dvb-ttpci: firmware @ card 0 supports CI link layer interface
-hda_codec: Unknown model for AD1988, trying auto-probe from BIOS...
-input: ImExPS/2 Logitech Explorer Mouse as /class/input/input2
+input: ImExPS/2 Logitech Explorer Mouse as /class/input/input4
 dvb-ttpci: adac type set to 0 @ card 0
 saa7146_vv: saa7146 (0): registered device video0 [v4l2]
 saa7146_vv: saa7146 (0): registered device vbi0 [v4l2]
 DVB: registering frontend 0 (ST STV0299 DVB-S)...
-input: DVB on-card IR receiver as /class/input/input3
+input: DVB on-card IR receiver as /class/input/input5
 dvb-ttpci: found av7110-0.
 EXT3 FS on sda6, internal journal
 device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: [email protected]

@@ -452,23 +466,16 @@
 EXT3-fs: mounted filesystem with ordered data mode.
 kjournald starting.  Commit interval 5 seconds
 EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
-EXT3 FS on hdf10, internal journal
+EXT3 FS on sda7, internal journal
 EXT3-fs: mounted filesystem with ordered data mode.
-skge eth0: enabling interface
-skge eth0: Link is up at 1000 Mbps, full duplex, flow control both
 NET: Registered protocol family 10
 lo: Disabled Privacy Extensions
-input: Power Button (FF) as /class/input/input4
-ACPI: Power Button (FF) [PWRF]
-input: Power Button (CM) as /class/input/input5
-ACPI: Power Button (CM) [PWRB]
 pnp: the driver 'parport_pc' has been registered
 lp: driver loaded but no devices found
 ppdev: user-space parallel port driver
-eth0: no IPv6 routers present
 [drm] Initialized drm 1.1.0 20060810
 ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
-[drm] Initialized radeon 1.25.0 20060524 on minor 0
+[drm] Initialized radeon 1.28.0 20060524 on minor 0
 [drm] Setting GART location based on new memory map
 [drm] Loading R300 Microcode
 [drm] writeback test succeeded in 1 usecs

Jan Gukelberger

author

2007-09-19 20:57 UTC #5 lore raw

Hi,

seems as if there are currently no more ideas?

So shall I perhaps open a bug in Kernel Bugzilla?

Thanks,
Jan

Quoted 59 lines · Jan Gukelberger

Quoted 25 lines · Stephen Hemminger
Quoted 22 lines · On Tue, 11 Sep 2007 12:58:24 +0200 Jan Gukelberger <[email protected]> wrote:
Quoted 2 lines · Stephen Hemminger
On Fri, 07 Sep 2007 18:42:35 +0200
Jan Gukelberger <[email protected]> wrote:
[...]
Quoted 11 lines
Quoted 9 lines
The key problem seem to be the following lines in dmesg:
------------------------------------------------------------------------
ACPI: PCI Interrupt 0000:04:04.0[A] -> GSI 19 (level, low) -> IRQ 19
PCI: Unable to reserve mem region #1:4000@ff9f8000 for device 0000:04:04.0 skge 0000:04:04.0: cannot obtain PCI resources
ACPI: PCI interrupt for device 0000:04:04.0 disabled
skge: probe of 0000:04:04.0 failed with error -16
------------------------------------------------------------------------
There is some kind of device conflict, please provide lspci -vvvxx output.
I'm attaching the output of 'lspci -vvvxx' on the working 2.6.20 kernel as well as the output of 'lspci -vvxxx' on 2.6.23-rc5 which I recorded earlier.
I you specifically need 'lspci -vvvxx' on 2.6.23-rc5 please drop me a note and I'll reboot quickly.
Quoted 6 lines
Quoted 2 lines
Thanks,
Jan
All looks in order, on the PCI tables. There is a firewire control just above the skge device, perhaps you enabled one of the firewire stacks in the configuration?
I did a quick diff of the respective kernel .config's (this is the configuration you mean, right?) and haven't found any notable differences in the firewire options.
Quoted 1 line
Perhaps the console (dmesg) output will show some clue.
I'm attaching a diff between dmesg of a working and a non-working boot. You can find the full dmesg records in my first mail and in the Debian BTS respectively.
The only thing I can see there is the old kernel having some problems with the SATA controller - even though I did never notice any unusual behaviour apart from these messages:
------------------------------------------------------------------------
PCI: Device 0000:02:00.0 not available because of resource collisions
ahci: probe of 0000:02:00.0 failed with error -22
JMB363: IDE controller at PCI slot 0000:02:00.0
PCI: Device 0000:02:00.0 not available because of resource collisions
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
JMB363: BIOS configuration fixed.
------------------------------------------------------------------------
Don't know whether this could be related?
Thanks,
Jan

Stephen Hemminger

2007-11-21 22:31 UTC #6 lore raw

Quoted 70 lines · On Wed, 19 Sep 2007 22:57:49 +0200 Jan Gukelberger <[email protected]> wrote:

Hi,
seems as if there are currently no more ideas?
So shall I perhaps open a bug in Kernel Bugzilla?
Thanks,
Jan
Quoted 59 lines · Jan Gukelberger
Quoted 25 lines · Stephen Hemminger
Quoted 22 lines · On Tue, 11 Sep 2007 12:58:24 +0200 Jan Gukelberger <[email protected]> wrote:
Quoted 2 lines · Stephen Hemminger
On Fri, 07 Sep 2007 18:42:35 +0200
Jan Gukelberger <[email protected]> wrote:
[...]
Quoted 11 lines
Quoted 9 lines
The key problem seem to be the following lines in dmesg:
------------------------------------------------------------------------
ACPI: PCI Interrupt 0000:04:04.0[A] -> GSI 19 (level, low) -> IRQ 19
PCI: Unable to reserve mem region #1:4000@ff9f8000 for device 0000:04:04.0 skge 0000:04:04.0: cannot obtain PCI resources
ACPI: PCI interrupt for device 0000:04:04.0 disabled
skge: probe of 0000:04:04.0 failed with error -16
------------------------------------------------------------------------
There is some kind of device conflict, please provide lspci -vvvxx output.
I'm attaching the output of 'lspci -vvvxx' on the working 2.6.20 kernel as well as the output of 'lspci -vvxxx' on 2.6.23-rc5 which I recorded earlier.
I you specifically need 'lspci -vvvxx' on 2.6.23-rc5 please drop me a note and I'll reboot quickly.
Quoted 6 lines
Quoted 2 lines
Thanks,
Jan
All looks in order, on the PCI tables. There is a firewire control just above the skge device, perhaps you enabled one of the firewire stacks in the configuration?
I did a quick diff of the respective kernel .config's (this is the configuration you mean, right?) and haven't found any notable differences in the firewire options.
Quoted 1 line
Perhaps the console (dmesg) output will show some clue.
I'm attaching a diff between dmesg of a working and a non-working boot. You can find the full dmesg records in my first mail and in the Debian BTS respectively.
The only thing I can see there is the old kernel having some problems with the SATA controller - even though I did never notice any unusual behaviour apart from these messages:
------------------------------------------------------------------------
PCI: Device 0000:02:00.0 not available because of resource collisions
ahci: probe of 0000:02:00.0 failed with error -22
JMB363: IDE controller at PCI slot 0000:02:00.0
PCI: Device 0000:02:00.0 not available because of resource collisions
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
JMB363: BIOS configuration fixed.
------------------------------------------------------------------------
Don't know whether this could be related?
Thanks,
Jan

The problem is in the tables (ACPI) from the BIOS. So ACPI driver (and/or BIOS) have to work out the resource assignments, the driver really has nothing to do with it.

Signature · 1 line

Stephen Hemminger <[email protected]>