ide: use only ->set_pio_mode method for programming PIO modes (take 2)

Index: b/drivers/ide/cris/ide-cris.c
===================================================================
@@ -724,11 +724,6 @@ static int speed_cris_ide(ide_drive_t *d
 {
 	int cyc = 0, dvs = 0, strobe = 0, hold = 0;
 
-	if (speed >= XFER_PIO_0 && speed <= XFER_PIO_4) {
-		cris_set_pio_mode(drive, speed - XFER_PIO_0);
-		return ide_config_drive_speed(drive, speed);
-	}
-
 	switch(speed)
 	{
 		case XFER_UDMA_0:

Index: b/drivers/ide/ide-lib.c
===================================================================
@@ -398,6 +398,18 @@ int ide_set_xfer_rate(ide_drive_t *drive
 
 	rate = ide_rate_filter(drive, rate);
 
+	if (rate >= XFER_PIO_0 && rate <= XFER_PIO_5) {
+		if (hwif->set_pio_mode)
+			hwif->set_pio_mode(drive, rate - XFER_PIO_0);
+
+		/*
+		 * FIXME: this is incorrect to return zero here but
+		 * since all users of ide_set_xfer_rate() ignore
+		 * the return value it is not a problem currently
+		 */
+		return 0;
+	}
+
 	return hwif->speedproc(drive, rate);
 }
 

Index: b/drivers/ide/mips/au1xxx-ide.c
===================================================================
@@ -177,11 +177,6 @@ static int auide_tune_chipset(ide_drive_
 	mem_sttime = 0;
 	mem_stcfg  = au_readl(MEM_STCFG2);
 
-	if (speed >= XFER_PIO_0 && speed <= XFER_PIO_4) {
-		au1xxx_set_pio_mode(drive, speed - XFER_PIO_0);
-		return 0;
-	}
-
 	switch(speed) {
 #ifdef CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
 	case XFER_MW_DMA_2:

Index: b/drivers/ide/pci/alim15x3.c
===================================================================
@@ -421,11 +421,6 @@ static int ali15x3_tune_chipset(ide_driv
 	if (speed < XFER_PIO_0)
 		return 1;
 
-	if (speed >= XFER_PIO_0 && speed <= XFER_PIO_5) {
-		ali_tune_pio(drive, speed - XFER_PIO_0);
-		return ide_config_drive_speed(drive, speed);
-	}
-
 	if (speed == XFER_UDMA_6)
 		speed1 = 0x47;
 

Index: b/drivers/ide/pci/atiixp.c
===================================================================
@@ -178,11 +178,6 @@ static int atiixp_speedproc(ide_drive_t 
 	u16 tmp16;
 	u8 pio;
 
-	if (speed >= XFER_PIO_0 && speed <= XFER_PIO_4) {
-		atiixp_tune_pio(drive, speed - XFER_PIO_0);
-		return ide_config_drive_speed(drive, speed);
-	}
-
 	spin_lock_irqsave(&atiixp_lock, flags);
 
 	save_mdma_mode[drive->dn] = 0;

Index: b/drivers/ide/pci/cmd64x.c
===================================================================
@@ -323,14 +323,6 @@ static int cmd64x_tune_chipset(ide_drive
 	case XFER_MW_DMA_0:
 		program_cycle_times(drive, 480, 215);
 		break;
-	case XFER_PIO_5:
-	case XFER_PIO_4:
-	case XFER_PIO_3:
-	case XFER_PIO_2:
-	case XFER_PIO_1:
-	case XFER_PIO_0:
-		cmd64x_tune_pio(drive, speed - XFER_PIO_0);
-		break;
 	default:
 		return 1;
 	}

Index: b/drivers/ide/pci/cs5520.c
===================================================================
@@ -66,30 +66,13 @@ static struct pio_clocks cs5520_pio_cloc
 	{1, 2, 1}
 };
 
-static int cs5520_tune_chipset(ide_drive_t *drive, const u8 speed)
+static void cs5520_set_pio_mode(ide_drive_t *drive, const u8 pio)
 {
 	ide_hwif_t *hwif = HWIF(drive);
 	struct pci_dev *pdev = hwif->pci_dev;
-	int pio = speed;
-	u8 reg;
 	int controller = drive->dn > 1 ? 1 : 0;
+	u8 reg;
 
-	switch(speed)
-	{
-		case XFER_PIO_4:
-		case XFER_PIO_3:
-		case XFER_PIO_2:
-		case XFER_PIO_1:
-		case XFER_PIO_0:
-			pio -= XFER_PIO_0;
-			break;
-		default:
-			pio = 0;
-			printk(KERN_ERR "cs55x0: bad ide timing.\n");
-	}
-	
-	printk("PIO clocking = %d\n", pio);
-	
 	/* FIXME: if DMA = 1 do we need to set the DMA bit here ? */
 
 	/* 8bit CAT/CRT - 8bit command timing for channel */

@@ -114,12 +97,21 @@ static int cs5520_tune_chipset(ide_drive
 	reg |= 1<<((drive->dn&1)+5);
 	outb(reg, hwif->dma_base + 0x02 + 8*controller);
 
-	return ide_config_drive_speed(drive, speed);
+	(void)ide_config_drive_speed(drive, XFER_PIO_0 + pio);
 }
 
-static void cs5520_set_pio_mode(ide_drive_t *drive, const u8 pio)
+static int cs5520_tune_chipset(ide_drive_t *drive, const u8 speed)
 {
-	cs5520_tune_chipset(drive, XFER_PIO_0 + pio);
+	printk(KERN_ERR "cs55x0: bad ide timing.\n");
+
+	cs5520_set_pio_mode(drive, 0);
+
+	/*
+	 * FIXME: this is incorrect to return zero here but
+	 * since all users of ide_set_xfer_rate() ignore
+	 * the return value it is not a problem currently
+	 */
+	return 0;
 }
 
 static int cs5520_config_drive_xfer_rate(ide_drive_t *drive)

Index: b/drivers/ide/pci/cs5530.c
===================================================================
@@ -163,13 +163,6 @@ static int cs5530_tune_chipset(ide_drive
 		case XFER_MW_DMA_0:	timings = 0x00077771; break;
 		case XFER_MW_DMA_1:	timings = 0x00012121; break;
 		case XFER_MW_DMA_2:	timings = 0x00002020; break;
-		case XFER_PIO_4:
-		case XFER_PIO_3:
-		case XFER_PIO_2:
-		case XFER_PIO_1:
-		case XFER_PIO_0:
-			cs5530_tunepio(drive, mode - XFER_PIO_0);
-			return 0;
 		default:
 			BUG();
 			break;

Index: b/drivers/ide/pci/it8213.c
===================================================================
@@ -132,11 +132,6 @@ static int it8213_tune_chipset(ide_drive
 	u16			reg4042, reg4a;
 	u8			reg48, reg54, reg55;
 
-	if (speed >= XFER_PIO_0 && speed <= XFER_PIO_4) {
-		it8213_tune_pio(drive, speed - XFER_PIO_0);
-		return ide_config_drive_speed(drive, speed);
-	}
-
 	pci_read_config_word(dev, maslave, &reg4042);
 	pci_read_config_byte(dev, 0x48, &reg48);
 	pci_read_config_word(dev, 0x4a, &reg4a);

Index: b/drivers/ide/pci/it821x.c
===================================================================
@@ -418,15 +418,6 @@ static int it821x_tune_chipset(ide_drive
 	ide_hwif_t *hwif	= drive->hwif;
 	struct it821x_dev *itdev = ide_get_hwifdata(hwif);
 
-	switch (speed) {
-	case XFER_PIO_4:
-	case XFER_PIO_3:
-	case XFER_PIO_2:
-	case XFER_PIO_1:
-	case XFER_PIO_0:
-		return it821x_tunepio(drive, speed - XFER_PIO_0);
-	}
-
 	if (itdev->smart == 0) {
 		switch (speed) {
 			/* MWDMA tuning is really hard because our MWDMA and PIO

Index: b/drivers/ide/pci/piix.c
===================================================================
@@ -242,11 +242,6 @@ static int piix_tune_chipset(ide_drive_t
 	u16			reg4042, reg4a;
 	u8			reg48, reg54, reg55;
 
-	if (speed >= XFER_PIO_0 && speed <= XFER_PIO_4) {
-		piix_tune_pio(drive, speed - XFER_PIO_0);
-		return ide_config_drive_speed(drive, speed);
-	}
-
 	pci_read_config_word(dev, maslave, &reg4042);
 	sitre = (reg4042 & 0x4000) ? 1 : 0;
 	pci_read_config_byte(dev, 0x48, &reg48);

Index: b/drivers/ide/pci/sc1200.c
===================================================================
@@ -152,16 +152,6 @@ static int sc1200_tune_chipset(ide_drive
 	if (sc1200_set_xfer_mode(drive, mode))
 		return 1;	/* failure */
 
-	switch (mode) {
-	case XFER_PIO_4:
-	case XFER_PIO_3:
-	case XFER_PIO_2:
-	case XFER_PIO_1:
-	case XFER_PIO_0:
-		sc1200_tunepio(drive, mode - XFER_PIO_0);
-		return 0;
-	}
-
 	pci_clock = sc1200_get_pci_clock();
 
 	/*

Index: b/drivers/ide/pci/scc_pata.c
===================================================================
@@ -270,13 +270,6 @@ static int scc_tune_chipset(ide_drive_t 
 	case XFER_UDMA_0:
 		idx = speed - XFER_UDMA_0;
 		break;
-	case XFER_PIO_4:
-	case XFER_PIO_3:
-	case XFER_PIO_2:
-	case XFER_PIO_1:
-	case XFER_PIO_0:
-		scc_tune_pio(drive, speed - XFER_PIO_0);
-		return ide_config_drive_speed(drive, speed);
 	default:
 		return 1;
 	}

Index: b/drivers/ide/pci/serverworks.c
===================================================================
@@ -157,11 +157,6 @@ static int svwks_tune_chipset(ide_drive_
 
 	u8 ultra_enable	 = 0, ultra_timing = 0, dma_timing = 0;
 
-	if (speed >= XFER_PIO_0 && speed <= XFER_PIO_4) {
-		svwks_tune_pio(drive, speed - XFER_PIO_0);
-		return ide_config_drive_speed(drive, speed);
-	}
-
 	/* If we are about to put a disk into UDMA mode we screwed up.
 	   Our code assumes we never _ever_ do this on an OSB4 */
 	   

Index: b/drivers/ide/pci/siimage.c
===================================================================
@@ -284,13 +284,6 @@ static int siimage_tune_chipset(ide_driv
 	scsc = is_sata(hwif) ? 1 : scsc;
 
 	switch(speed) {
-		case XFER_PIO_4:
-		case XFER_PIO_3:
-		case XFER_PIO_2:
-		case XFER_PIO_1:
-		case XFER_PIO_0:
-			sil_tune_pio(drive, speed - XFER_PIO_0);
-			return ide_config_drive_speed(drive, speed);
 		case XFER_MW_DMA_2:
 		case XFER_MW_DMA_1:
 		case XFER_MW_DMA_0:

Index: b/drivers/ide/pci/sis5513.c
===================================================================
@@ -519,15 +519,10 @@ static void config_art_rwp_pio (ide_driv
 	}
 }
 
-static int sis5513_tune_drive(ide_drive_t *drive, const u8 pio)
-{
-	config_art_rwp_pio(drive, pio);
-	return ide_config_drive_speed(drive, XFER_PIO_0 + pio);
-}
-
 static void sis_set_pio_mode(ide_drive_t *drive, const u8 pio)
 {
-	(void)sis5513_tune_drive(drive, pio);
+	config_art_rwp_pio(drive, pio);
+	(void)ide_config_drive_speed(drive, XFER_PIO_0 + pio);
 }
 
 static int sis5513_tune_chipset(ide_drive_t *drive, const u8 speed)

@@ -537,9 +532,6 @@ static int sis5513_tune_chipset(ide_driv
 	u32 regdw;
 	u8 drive_pci, reg;
 
-	if (speed >= XFER_PIO_0 && speed <= XFER_PIO_4)
-		return sis5513_tune_drive(drive, speed - XFER_PIO_0);
-
 	/* See config_art_rwp_pio for drive pci config registers */
 	drive_pci = 0x40;
 	if (chipset_family >= ATA_133) {

Index: b/drivers/ide/pci/sl82c105.c
===================================================================
@@ -139,14 +139,6 @@ static int sl82c105_tune_chipset(ide_dri
 			pci_write_config_word(dev, reg, drv_ctrl);
 		}
 		break;
-	case XFER_PIO_5:
-	case XFER_PIO_4:
-	case XFER_PIO_3:
-	case XFER_PIO_2:
-	case XFER_PIO_1:
-	case XFER_PIO_0:
-		sl82c105_tune_pio(drive, speed - XFER_PIO_0);
-		break;
 	default:
 		return -1;
 	}

Index: b/drivers/ide/pci/slc90e66.c
===================================================================
@@ -110,11 +110,6 @@ static int slc90e66_tune_chipset(ide_dri
 	int u_speed = 0, u_flag = 1 << drive->dn;
 	u16			reg4042, reg44, reg48, reg4a;
 
-	if (speed >= XFER_PIO_0 && speed <= XFER_PIO_4) {
-		slc90e66_tune_pio(drive, speed - XFER_PIO_0);
-		return ide_config_drive_speed(drive, speed);
-	}
-
 	pci_read_config_word(dev, maslave, &reg4042);
 	sitre = (reg4042 & 0x4000) ? 1 : 0;
 	pci_read_config_word(dev, 0x44, &reg44);

Index: b/drivers/ide/ppc/pmac.c
===================================================================
@@ -917,7 +917,7 @@ set_timings_mdma(ide_drive_t *drive, int
 
 /* 
  * Speedproc. This function is called by the core to set any of the standard
- * timing (PIO, MDMA or UDMA) to both the drive and the controller.
+ * DMA timing (MDMA or UDMA) to both the drive and the controller.
  * You may notice we don't use this function on normal "dma check" operation,
  * our dedicated function is more precise as it uses the drive provided
  * cycle time value. We should probably fix this one to deal with that too...

@@ -964,13 +964,6 @@ static int pmac_ide_tune_chipset(ide_dri
 		case XFER_SW_DMA_0:
 			return 1;
 #endif /* CONFIG_BLK_DEV_IDEDMA_PMAC */
-		case XFER_PIO_4:
-		case XFER_PIO_3:
-		case XFER_PIO_2:
-		case XFER_PIO_1:
-		case XFER_PIO_0:
-			pmac_ide_set_pio_mode(drive, speed & 0x07);
-			return 0;
 		default:
 			ret = 1;
 	}