Skip to contentSkip to conversation

Syba 8-Port Serial Card Unidentified By Kernel

DISCUSSION Chris Bergeron 5 participants 22 messages Oct 5, 2007 – Sep 20, 2008 2 messages not in the archive

lore
Share & tools
lore
#0 lore raw

Hello all,

I've just installed a multiport serial card released by an outfit called Syba. This is an 8 port serial-only card with an Octopus style breakout cable. The main chipset on it is an ITE IT8871F.

I've got two questions on this: Is there a driver I should try force loading on it (and if so, what options to use)? and is there any useful testing I can do to report back to the LKML on this card?

Thanks for your time, diagnostic output follows.
-- Chris

The following comes up from an "lspci -vv"

01:06.0 Serial controller: PLX Technology, Inc. Unknown device 9016 (rev 01) (prog-if 02 [16550])
Subsystem: Unknown device 544e:0008
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

       Interrupt: pin A routed to IRQ 16
       Region 0: I/O ports at a000 [size=64]
       Region 1: I/O ports at a400 [size=16]
       Region 2: I/O ports at a800 [size=16]
       Region 3: Memory at f5000000 (32-bit, non-prefetchable) [size=4K]
       Region 4: Memory at f5001000 (32-bit, non-prefetchable) [size=4K]
       Region 5: Memory at f5002000 (32-bit, non-prefetchable) [size=4K]

and "lshw" outputs:

*-communication UNCLAIMED
description: Serial controller
product: PLX Technology, Inc.
vendor: PLX Technology, Inc.
physical id: 6
bus info: pci@0000:01:06.0
version: 01
width: 32 bits
clock: 33MHz
capabilities: 16550
configuration: latency=0

#1 lore raw
Quoted 22 lines · Chris Bergeron

Hello all,

I've just installed a multiport serial card released by an outfit called Syba. This is an 8 port serial-only card with an Octopus style breakout cable. The main chipset on it is an ITE IT8871F.

I've got two questions on this: Is there a driver I should try force loading on it (and if so, what options to use)? and is there any useful testing I can do to report back to the LKML on this card?

Thanks for your time, diagnostic output follows.
-- Chris

The following comes up from an "lspci -vv"

01:06.0 Serial controller: PLX Technology, Inc. Unknown device 9016 (rev
01) (prog-if 02 [16550])
Subsystem: Unknown device 544e:0008
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

Quoted 7 lines
        Interrupt: pin A routed to IRQ 16
        Region 0: I/O ports at a000 [size=64]
        Region 1: I/O ports at a400 [size=16]
        Region 2: I/O ports at a800 [size=16]
        Region 3: Memory at f5000000 (32-bit, non-prefetchable) [size=4K]
        Region 4: Memory at f5001000 (32-bit, non-prefetchable) [size=4K]
        Region 5: Memory at f5002000 (32-bit, non-prefetchable) [size=4K]

Try echo -n "10b5 9016" > /sys/bus/pci/drivers/serial/new_id and let Russell King ([email protected]) know if it works (or if it doesn't, for that matter).

Signature · 1 line
Nicholas Miell <[email protected]>
#2 lore raw
In reply to Chris Bergeron
Quoted 3 lines · Chris Bergeron

I've just installed a multiport serial card released by an outfit called Syba. This is an 8 port serial-only card with an Octopus style breakout cable. The main chipset on it is an ITE IT8871F.

Well 8250_pci.c mentions IT8871, so it is probably 8250 style in interface then.

Quoted 3 lines

I've got two questions on this: Is there a driver I should try force loading on it (and if so, what options to use)? and is there any useful testing I can do to report back to the LKML on this card?

How many serial ports is your kernel configured to use?

CONFIG_SERIAL_8250_NR_UARTS=16
CONFIG_SERIAL_8250_RUNTIME_UARTS=4

That is from my Debian system's kernel, and it won't activate more than 4 ports automatically. It will allow up to 16 to be activated though. I don't remember what the boot command is to override those values to make the system look for more ports.

--
Len Sorensen

#3 lore raw
Quoted 9 lines · Lennart Sorensen
Quoted 2 lines · Chris Bergeron

I've just installed a multiport serial card released by an outfit called Syba. This is an 8 port serial-only card with an Octopus style breakout cable. The main chipset on it is an ITE IT8871F.

Well 8250_pci.c mentions IT8871, so it is probably 8250 style in interface then.

That's what I had thought too after a quick LKML search. Doing a bit more research (I'm starting to think the IT8871F on the chip is misleading) it looks like that support is for a single parallel multi I/O card (with the other 887x cards being serial/parport PCI cards).

Quoted 5 lines
Quoted 2 lines

I've got two questions on this: Is there a driver I should try force loading on it (and if so, what options to use)? and is there any useful testing I can do to report back to the LKML on this card?

How many serial ports is your kernel configured to use?

The kernel I'm using has 16 for both the NR_UARTS and RUNTIME_UARTS (these machines generally have a minimum of 4 ports). dmesg doesn't show the kernel as recognizing the card and only ttyS0 and ttyS1 (the two onboard ports) show up on boot.

-- Chris

#4 lore raw
In reply to Chris Bergeron
Quoted 5 lines · Chris Bergeron

Hello all,

I've just installed a multiport serial card released by an outfit called Syba. This is an 8 port serial-only card with an Octopus style breakout cable. The main chipset on it is an ITE IT8871F.

Are you sure ? IIRC IT887x are PCI-ISA bridges with additional periphery and your lspci shows PLX chip. Can you send complete lspci -vv output ? Output of dmesg could be useful too.

Quoted 44 lines

I've got two questions on this: Is there a driver I should try force loading on it (and if so, what options to use)? and is there any useful testing I can do to report back to the LKML on this card?

Thanks for your time, diagnostic output follows.
-- Chris

The following comes up from an "lspci -vv"

01:06.0 Serial controller: PLX Technology, Inc. Unknown device 9016 (rev
01) (prog-if 02 [16550])
Subsystem: Unknown device 544e:0008
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

       Interrupt: pin A routed to IRQ 16
       Region 0: I/O ports at a000 [size=64]
       Region 1: I/O ports at a400 [size=16]
       Region 2: I/O ports at a800 [size=16]
       Region 3: Memory at f5000000 (32-bit, non-prefetchable) [size=4K]
       Region 4: Memory at f5001000 (32-bit, non-prefetchable) [size=4K]
       Region 5: Memory at f5002000 (32-bit, non-prefetchable) [size=4K]

and "lshw" outputs:

*-communication UNCLAIMED
description: Serial controller
product: PLX Technology, Inc.
vendor: PLX Technology, Inc.
physical id: 6
bus info: pci@0000:01:06.0
version: 01
width: 32 bits
clock: 33MHz
capabilities: 16550
configuration: latency=0

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Signature · 2 lines
Andrey Panin		| Linux and UNIX system administrator
[email protected]		| PGP key: wwwkeys.pgp.net
#5 lore raw
Quoted 13 lines · Andrey Panin
Quoted 4 lines · Chris Bergeron

Hello all,

I've just installed a multiport serial card released by an outfit called Syba. This is an 8 port serial-only card with an Octopus style breakout cable. The main chipset on it is an ITE IT8871F.

Are you sure ? IIRC IT887x are PCI-ISA bridges with additional periphery and your lspci shows PLX chip. Can you send complete lspci -vv output ? Output of dmesg could be useful too.

I'm sure that's what it says on the largest chip on the PCI card. It could be that the other two chips are more relevant... the numbers from them are included below.

I've posted up a quick text only page with the diagnostic information from the system (full dmesg, lspci, etc) plus links to pictures of the board (since others might see something important that I'm not aware of). You can access that at http://pcburn.com/files/Syba_serial_controller/index.html

One chip has "ITE IT8871F 0641-AYS ZF1M04L" written on it, and the other two have a stylized celtic knot looking "T" followed by "TG16C554CJG FTA6M-001 0620-B".

#6 lore raw
Quoted 10 lines · Chris Bergeron

I'm sure that's what it says on the largest chip on the PCI card. It could be that the other two chips are more relevant... the numbers from them are included below.

I've posted up a quick text only page with the diagnostic information from the system (full dmesg, lspci, etc) plus links to pictures of the board (since others might see something important that I'm not aware of). You can access that at
http://pcburn.com/files/Syba_serial_controller/index.html

Quoted 3 lines

One chip has "ITE IT8871F 0641-AYS ZF1M04L" written on it, and the other two have a stylized celtic knot looking "T" followed by "TG16C554CJG FTA6M-001 0620-B".

Well TG16C554 sounds awfully similar to 16550 which is a common UART type. Perhaps 554 indicates it is 4 16550s in one chip. There are two of those chips in one of the pictures.

Here is a data sheet for it:
http://www.twistsemi.com/downloads/TG16C554V1.5.pdf

It is in fact a quad UART chip. It appears to have 4 chip select lines to pick between the 4 UARTS, 3 address lines to access the 8 16550 registers, and 8 data lines to read and write those registers as well as a pair of read and write enable lines. They are NOT PCI chips, so quite likely the IT8871 is there as a PCI to parallel convertor and then the parallel interface connects to the UARTs. No idea where the IRQ line from the chips would connect to (one of the parallel port signals that generates an IRQ?)

The 8 small chips are probably RS232 level convertors.

The 8871 is a single PCI parallel port, so certainly somehow they are controlling the two serial to parallel chips through that pci parallel port.

I included the diff of the files you had on your web page and the originals founds in 2.4.20 (which is what they claim they replace).

I can't really tell if there is any code there to deal with their quad uart chip or not.

tmp/serial_20.c renamed from char/serial.c +176 -1
@@ -257,6 +257,13 @@
 
 static struct timer_list serial_timer;
 
+//struct pci_dev *pcidev = NULL;
+// ITE8872 ITE8872
+u32 ITE8872_INTC[8];
+int ITEBOARDNUMBER=0;
+u8 ITE8872_IRQ[8];
+
+
 /* serial subtype definitions */
 #ifndef SERIAL_TYPE_NORMAL
 #define SERIAL_TYPE_NORMAL	1
@@ -4165,6 +4172,163 @@
 }
 EXPORT_SYMBOL(pci_siig20x_fn);
 
+void ite8872_requestirq(int irq,void *dev_id,struct pt_regs *regs){
+	u8 itmp;
+	int i=0;
+	/* measure which INTC went to control */
+	for(i=0;i<8;i++)
+	  if(irq == ITE8872_IRQ[i])
+	 {
+	/* clean ITE8872 interrupt */
+	itmp = inb(ITE8872_INTC[i]+2);
+	if(itmp & 0x0f)
+	{
+	outb(itmp,ITE8872_INTC[i]+2);
+	break;
+	}
+	 }
+}
+
+
+/*
+Integrated Technology Express, Inc.
+IT887x Device Driver
+*/
+static int __devinit
+pci_ite8872_fn(struct pci_dev *pcidev, struct pci_board *board, int enable)
+{
+	int result,ite8872comnum=0,ite8872parportnum=0;
+	short INTA_Addr[8]={ 0x2a0,0x2c0,0x220,0x240,0x1E0,0x200,0x280};
+	u32 j=0,u32Tmp,itmp,ITE8872_COM1,ITE8872_COM2,ITE8872SET=0x64E00000,set60,set78,intc;
+       	u32 ite8872_lpt, ite8872_lpthi;
+	
+	printk(KERN_INFO "ITE8872 serial init\n");
+	if (!enable) return 0;
+
+	pci_read_config_dword(pcidev, 0x60,&set60);
+	pci_read_config_dword(pcidev, 0x78,&set78);
+
+	for(j=0; j<7; j++)
+       		if(check_region(INTA_Addr[j], 0x8) >=0){
+		pci_write_config_dword(pcidev, 0x60,0xE7000000|INTA_Addr[j]);
+			pci_write_config_dword(pcidev, 0x78,0x00000000|INTA_Addr[j]);
+        		itmp = inb( INTA_Addr[j]);
+        		if( itmp != 0xFF ) break;
+        	}
+  	       	
+	if( j>=7 ){
+       		printk(KERN_INFO "ITE8872 INTA cannot find.\n");
+       		return 0;
+       	}
+
+	itmp = INTA_Addr[j];
+	u32Tmp = inb(itmp+0x18);
+	u32Tmp &= 0x0F;
+	intc= INTA_Addr[j];
+	switch(u32Tmp){
+		case 0x2:
+			printk(KERN_INFO "ITE887x: ITE8871 found , Parallel*1 \n");
+			ITE8872SET = 0x64200000;
+			ite8872parportnum=1;
+			request_region(intc,0x8,"ite8871");
+			break;
+		case 0xA:
+			printk(KERN_INFO "ITE887x: ITE8875 found , Parallel*1 \n");
+			ITE8872SET = 0x64200000;
+			ite8872parportnum=1;
+			request_region(intc,0x8,"ite8875");
+			break;
+		case 0xE:
+			printk(KERN_INFO "ITE887x: ITE8872 found , Serial *2 , Parallel*1 \n");
+			ite8872comnum = 2;
+			ite8872parportnum=1;
+			ITE8872SET=0x64E00000;
+			request_region(intc,0x8,"ite8872");
+			break;
+		case 0x6:
+			printk(KERN_INFO "ITE887x: ITE8873 found , Serial *1 \n");
+			ite8872comnum = 1;
+			ITE8872SET=0x64800000;
+			request_region(intc,0x8,"ite8873");
+			break;
+		case 0x8:
+			printk(KERN_INFO "ITE887x: ITE8874 found , Serial *2 \n");
+			ite8872comnum = 2;
+			ITE8872SET=0x64C00000;
+			request_region(intc,0x8,"ite8874");
+			break;
+		default:
+			printk(KERN_INFO "ITE887x: unknow ITE887x \n");
+			printk(KERN_INFO "ITE887x: please mail lspci -nvv output to [email protected]\n");
+			pci_write_config_dword(pcidev, 0x60,set60);
+			pci_write_config_dword(pcidev, 0x78,set78);
+			return 0;
+			break;
+	}
+
+//	pci_read_config_dword(pcidev, 0x3c,&ITE8872_IRQ[ITEBOARDNUMBER]);
+	ITE8872_IRQ[ITEBOARDNUMBER]=pcidev->irq;
+	
+	printk(KERN_INFO "ITE887X_IRQ : %d \n", ITE8872_IRQ[ITEBOARDNUMBER]);
+	if (ite8872comnum>=1) {
+	result = request_irq(ITE8872_IRQ[ITEBOARDNUMBER],ite8872_requestirq,SA_SHIRQ,"ite8872",&ITE8872_IRQ[ITEBOARDNUMBER]);
+	if(result){
+	printk(KERN_INFO "ITE887x: can't get assign irq :%x \n",ITE8872_IRQ[ITEBOARDNUMBER]);
+		return 0;
+	 }
+	}
+
+
+	//INTC
+	pci_read_config_dword( pcidev, 0x10, &ITE8872_INTC[ITEBOARDNUMBER]);
+	ITE8872_INTC[ITEBOARDNUMBER] &= 0x0000FF00;
+	pci_write_config_dword( pcidev, 0x60, 0xE5000000|ITE8872_INTC[ITEBOARDNUMBER] );
+	pci_write_config_dword( pcidev, 0x78, ITE8872_INTC[ITEBOARDNUMBER] );
+
+	if (ite8872parportnum>=1)
+	{
+	//parport
+	pci_read_config_dword (pcidev, 0x1c, &ite8872_lpt);
+	ite8872_lpt &= 0x0000ff00;
+	pci_read_config_dword (pcidev, 0x20, &ite8872_lpthi);
+	ite8872_lpthi &= 0x0000ff00;
+	pci_write_config_dword (pcidev, 0x6c, 0xe3000000 | ite8872_lpt);
+	pci_write_config_dword (pcidev, 0x70, 0xe3000000 | ite8872_lpthi);
+	pci_write_config_dword (pcidev, 0x80, (ite8872_lpthi<<16) | ite8872_lpt);
+	// SET SPP&EPP , Parallel Port NO DMA , Enable All Function
+	// SET Parallel IRQ
+	printk (KERN_INFO "ITE887x: The PARALLEL I/O port is 0x%x.\n",
+		 ite8872_lpt);
+	printk (KERN_INFO "ITE887x: The PARALLEL I/O porthi is 0x%x.\n",
+		 ite8872_lpthi);
+	}
+	
+	if (ite8872comnum>=1){
+	//COM1
+	pci_read_config_dword( pcidev, 0x14,&ITE8872_COM1);
+	ITE8872_COM1 &= 0x0000FF00;
+	pci_write_config_dword( pcidev, 0x64, 0xE3000000|ITE8872_COM1);
+
+	//COM2
+	if(ite8872comnum == 2){
+	pci_read_config_dword( pcidev, 0x18,&ITE8872_COM2);
+	ITE8872_COM2 &= 0x0000FF00;
+	pci_write_config_dword( pcidev, 0x68, 0xE3000000|ITE8872_COM2);
+	}
+	else	ITE8872_COM2 = 0;
+	
+	pci_write_config_dword( pcidev, 0x7C, (ITE8872_COM2<<16)|(ITE8872_COM1) );
+	}
+	
+	// 9C write enable UART , IRQ Function
+	pci_write_config_dword( pcidev, 0x9c,ITE8872SET|(0x11111*ITE8872_IRQ[ITEBOARDNUMBER]));
+	// Add next interface
+	ITEBOARDNUMBER++;
+       return 0;
+
+}
+
+
 /* Added for EKF Intel i960 serial boards */
 static int __devinit
 pci_inteli960ni_fn(struct pci_dev *dev,
@@ -4348,6 +4512,9 @@
 #ifdef CONFIG_DDB5074
 	pbn_nec_nile4,
 #endif
+#if 1
+        pbn_ite_8872,
+#endif
 #if 0
 	pbn_dci_pccom8,
 #endif
@@ -4444,6 +4611,10 @@
 	{ SPCI_FL_BASE0, 1, 520833,			   /* pbn_nec_nile4 */
 		64, 3, NULL, 0x300 },
 #endif
+#if 1   /* PCI_DEVCE_ID_ITE_8872 */
+        {SPCI_FL_BASE1| SPCI_FL_BASE_TABLE, 2, 115200,
+		0, 0, pci_ite8872_fn, 0},
+#endif
 #if 0	/* PCI_DEVICE_ID_DCI_PCCOM8 ? */		   /* pbn_dci_pccom8 */
 	{ SPCI_FL_BASE3, 8, 115200, 8 },
 #endif
@@ -4906,7 +5077,11 @@
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
 		pbn_nec_nile4 },
 #endif
-
+#if 1	/* ITE 8872 Serial Simple Board */
+	{	PCI_VENDOR_ID_ITE, PCI_DEVICE_ID_ITE_8872,
+		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+		pbn_ite_8872 },
+#endif
 #if 0	/* PCI_DEVICE_ID_DCI_PCCOM8 ? */
 	{	PCI_VENDOR_ID_DCI, PCI_DEVICE_ID_DCI_PCCOM8,
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
tmp/parport_pc_20.c renamed from parport/parport_pc.c +16 -66

111 lines not on this page · raw message

--
Len Sorensen

#7 lore raw
Quoted 9 lines · Lennart Sorensen
Quoted 2 lines · Chris Bergeron

One chip has "ITE IT8871F 0641-AYS ZF1M04L" written on it, and the other two have a stylized celtic knot looking "T" followed by "TG16C554CJG FTA6M-001 0620-B".

The 8871 is a single PCI parallel port, so certainly somehow they are controlling the two serial to parallel chips through that pci parallel port.

Quoted 6 lines

I included the diff of the files you had on your web page and the originals founds in 2.4.20 (which is what they claim they replace).

I can't really tell if there is any code there to deal with their quad uart chip or not.

I'll see if I can compile up the appropriate kernel and test it with that code to see if it includes something to drive the card then, for starters.

-- Chris

#8 lore raw
In reply to Chris Bergeron
Quoted 20 lines · Chris Bergeron
Quoted 4 lines · Andrey Panin
Quoted 2 lines · Chris Bergeron

Hello all,

Quoted 11 lines
Quoted 4 lines

I've just installed a multiport serial card released by an outfit called Syba. This is an 8 port serial-only card with an Octopus style breakout cable. The main chipset on it is an ITE IT8871F.

Are you sure ? IIRC IT887x are PCI-ISA bridges with additional periphery and your lspci shows PLX chip. Can you send complete lspci -vv output ? Output of dmesg could be useful too.

I'm sure that's what it says on the largest chip on the PCI card. It could be that the other two chips are more relevant... the numbers from them are included below.

Quoted 5 lines

I've posted up a quick text only page with the diagnostic information from the system (full dmesg, lspci, etc) plus links to pictures of the board (since others might see something important that I'm not aware of). You can access that at
http://pcburn.com/files/Syba_serial_controller/index.html

Can you try an attached patch ? I hope it should at least detect UARTs on your board. Be ready that baudrate could be wrong, because we do not know what frequency is used to clock these UARTs.

Quoted 3 lines

One chip has "ITE IT8871F 0641-AYS ZF1M04L" written on it, and the other two have a stylized celtic knot looking "T" followed by "TG16C554CJG FTA6M-001 0620-B".

Signature · 2 lines
Andrey Panin		| Linux and UNIX system administrator
[email protected]		| PGP key: wwwkeys.pgp.net
drivers/serial/8250_pci.c +12 -0
diff -urdpNX /usr/share/dontdiff linux-2.6.23.vanilla/drivers/serial/8250_pci.c linux-2.6.23/drivers/serial/8250_pci.c
@@ -1036,6 +1036,7 @@ enum pci_board_num_t {
 	pbn_b0_2_115200,
 	pbn_b0_4_115200,
 	pbn_b0_5_115200,
+	pbn_b0_8_115200,
 
 	pbn_b0_1_921600,
 	pbn_b0_2_921600,
@@ -1172,6 +1173,12 @@ static struct pciserial_board pci_boards
 		.base_baud	= 115200,
 		.uart_offset	= 8,
 	},
+	[pbn_b0_8_115200] = {
+		.flags		= FL_BASE0,
+		.num_ports	= 8,
+		.base_baud	= 115200,
+		.uart_offset	= 8,
+	},
 
 	[pbn_b0_1_921600] = {
 		.flags		= FL_BASE0,
@@ -2520,6 +2527,11 @@ static struct pci_device_id serial_pci_t
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
 		pbn_b3_8_115200 },
 
+	/* Syba PCI8871-PR8 8-port serial card */
+	{	PCI_VENDOR_ID_PLX, 0x9016,
+		0x544e, 0x0008, 0, 0,
+		pbn_b0_8_115200 },
+
 	/*
 	 * Exar Corp. XR17C15[248] Dual/Quad/Octal UART
 	 */
#9 lore raw
Quoted 17 lines · Andrey Panin
Quoted 15 lines · Chris Bergeron
Quoted 13 lines · Andrey Panin
Quoted 5 lines · Chris Bergeron

Hello all,

I've just installed a multiport serial card released by an outfit called Syba. This is an 8 port serial-only card with an Octopus style breakout cable. The main chipset on it is an ITE IT8871F.

Are you sure ? IIRC IT887x are PCI-ISA bridges with additional periphery and your lspci shows PLX chip. Can you send complete lspci -vv output ? Output of dmesg could be useful too.

Quoted 9 lines
Quoted 4 lines

I'm sure that's what it says on the largest chip on the PCI card. It could be that the other two chips are more relevant... the numbers from them are included below.

I've posted up a quick text only page with the diagnostic information from the system (full dmesg, lspci, etc) plus links to pictures of the board (since others might see something important that I'm not aware of). You can access that at http://pcburn.com/files/Syba_serial_controller/index.html

Can you try an attached patch ? I hope it should at least detect UARTs on your board. Be ready that baudrate could be wrong, because we do not know what frequency is used to clock these UARTs.

Alright,finally had another machine to try the attached patch. I get an odd error regarding IRQ 17:

"irq 17: nobody cared (try booting with the "irqpoll" option)"

along with a long error message (but the kernel continues to load). Aside from that the ports now allow me to run a getty on them and the DTR line lights up on my serial tester (as it does with a working port) but the device on the other end doesn't function.

I've updated the web page with lspci -vv and dmesg output. I can also post it here if that's desirable, just figured I'd save everyone the inbox flooding :).

-- Chris

#10 lore raw
Quoted 34 lines · Chris Bergeron
Quoted 28 lines · Andrey Panin
Quoted 19 lines · Chris Bergeron
Quoted 4 lines · Andrey Panin
Quoted 2 lines · Chris Bergeron

Hello all,

Quoted 9 lines
Quoted 4 lines

I've just installed a multiport serial card released by an outfit called Syba. This is an 8 port serial-only card with an Octopus style breakout cable. The main chipset on it is an ITE IT8871F.

Are you sure ? IIRC IT887x are PCI-ISA bridges with additional periphery and your lspci shows PLX chip. Can you send complete lspci -vv output ? Output of dmesg could be useful too.

I'm sure that's what it says on the largest chip on the PCI card. It could be that the other two chips are more relevant... the numbers from them are included below.

Quoted 6 lines

I've posted up a quick text only page with the diagnostic information from the system (full dmesg, lspci, etc) plus links to pictures of the board (since others might see something important that I'm not aware of).
You can access that at
http://pcburn.com/files/Syba_serial_controller/index.html

Quoted 5 lines

Can you try an attached patch ? I hope it should at least detect UARTs on your board. Be ready that baudrate could be wrong, because we do not know what frequency is used to clock these UARTs.

Quoted 4 lines

Alright,finally had another machine to try the attached patch. I get an odd error regarding IRQ 17:

"irq 17: nobody cared (try booting with the "irqpoll" option)"

This message apearred after firewire driver initialization and firewire chip shares IRQ with serial card. It's hard to say who is guilty here :)

Quoted 4 lines

along with a long error message (but the kernel continues to load). Aside from that the ports now allow me to run a getty on them and the DTR line lights up on my serial tester (as it does with a working port) but the device on the other end doesn't function.

Is it possible to connect two ports and run getty on one port and minicom on another ? We should check that UARTs are really working.

Quoted 5 lines

I've updated the web page with lspci -vv and dmesg output. I can also post it here if that's desirable, just figured I'd save everyone the inbox flooding :).

-- Chris

Signature · 2 lines
Andrey Panin		| Linux and UNIX system administrator
[email protected]		| PGP key: wwwkeys.pgp.net
#11 lore raw
Quoted 5 lines · Andrey Panin

Is it possible to connect two ports and run getty on one port and minicom on another ? We should check that UARTs are really working.

I used the on-board serial port as a known working control (after getting it to work with the other onboard serial port) to try and connect over to one of the Syba card ports (using Cutecom & getty). The lines light up, but there's nothing getting sent from the 8-port as far as I can see. The onboard port works as I'd expect, the Syba (running getty identically from inittab) doesn't.

-- Chris

#12 lore raw
Quoted 11 lines · Chris Bergeron
Quoted 6 lines · Andrey Panin

Is it possible to connect two ports and run getty on one port and minicom on
another ? We should check that UARTs are really working.

I used the on-board serial port as a known working control (after getting it to work with the other onboard serial port) to try and connect over to one of the Syba card ports (using Cutecom & getty). The lines light up, but there's nothing getting sent from the 8-port as far as I can see.

Oh crap... I missed this fscking "Disabling IRQ #17" line in your dmesg. Can you try with firewire controller disabled somehow ?

Signature · 2 lines
Andrey Panin		| Linux and UNIX system administrator
[email protected]		| PGP key: wwwkeys.pgp.net
#13 lore raw
Quoted 9 lines · Andrey Panin
Quoted 7 lines · Chris Bergeron
Quoted 5 lines · Andrey Panin

Is it possible to connect two ports and run getty on one port and minicom on another ? We should check that UARTs are really working.

Quoted 7 lines
Quoted 2 lines

I used the on-board serial port as a known working control (after getting it to work with the other onboard serial port) to try and connect over to one of the Syba card ports (using Cutecom & getty). The lines light up, but there's nothing getting sent from the 8-port as far as I can see.

Oh crap... I missed this fscking "Disabling IRQ #17" line in your dmesg. Can you try with firewire controller disabled somehow ?

Ah, I forgot to make note of that. I did actually turn off Firewire in the BIOS. Assuming that worked (and it looks like it did) the following section probably contains the relevant bits. Still getting the IRQ 17 error.

-- Chris

PCI: Setting latency timer of device 0000:00:05.0 to 64
NET: Registered protocol family 17
eth0: no IPv6 routers present
irq 17: nobody cared (try booting with the "irqpoll" option)

[<c0104f45>] show_trace_log_lvl+0x1a/0x2f
[<c0105939>] show_trace+0x12/0x14
[<c0105951>] dump_stack+0x16/0x18
[<c0152f90>] __report_bad_irq+0x39/0x79
[<c01531af>] note_interrupt+0x1df/0x218
[<c0153754>] handle_fasteoi_irq+0x91/0xb6
[<c0105fef>] do_IRQ+0x7c/0x95
[<c0104946>] common_interrupt+0x2e/0x34
[<c010233a>] cpu_idle+0x1c/0xc2
[<c02deed9>] rest_init+0x4d/0x4f
[<c03e7979>] start_kernel+0x32a/0x332

[<00000000>] 0x0
=======================
handlers:
[<c023ecae>] (serial8250_interrupt+0x0/0x115)
Disabling IRQ #17
hda: DMA timeout retry

full dmesg output at http://pcburn.com/files/Syba_serial_controller/dmesg_with_1394_disabled.txt

#14 lore raw
Quoted 50 lines · Chris Bergeron
Quoted 9 lines · Andrey Panin
Quoted 7 lines · Chris Bergeron
Quoted 5 lines · Andrey Panin

Is it possible to connect two ports and run getty on one port and minicom on
another ? We should check that UARTs are really working.

Quoted 10 lines
Quoted 5 lines

I used the on-board serial port as a known working control (after getting it to work with the other onboard serial port) to try and connect over to one of the Syba card ports (using Cutecom & getty). The lines light up, but there's nothing getting sent from the 8-port as far as I can see.

Oh crap... I missed this fscking "Disabling IRQ #17" line in your dmesg. Can you try with firewire controller disabled somehow ?

Ah, I forgot to make note of that. I did actually turn off Firewire in the BIOS. Assuming that worked (and it looks like it did) the following section probably contains the relevant bits. Still getting the IRQ 17 error.

-- Chris

PCI: Setting latency timer of device 0000:00:05.0 to 64
NET: Registered protocol family 17
eth0: no IPv6 routers present
irq 17: nobody cared (try booting with the "irqpoll" option)

[<c0104f45>] show_trace_log_lvl+0x1a/0x2f
[<c0105939>] show_trace+0x12/0x14
[<c0105951>] dump_stack+0x16/0x18
[<c0152f90>] __report_bad_irq+0x39/0x79
[<c01531af>] note_interrupt+0x1df/0x218
[<c0153754>] handle_fasteoi_irq+0x91/0xb6
[<c0105fef>] do_IRQ+0x7c/0x95
[<c0104946>] common_interrupt+0x2e/0x34
[<c010233a>] cpu_idle+0x1c/0xc2
[<c02deed9>] rest_init+0x4d/0x4f
[<c03e7979>] start_kernel+0x32a/0x332

[<00000000>] 0x0
=======================
handlers:
[<c023ecae>] (serial8250_interrupt+0x0/0x115)
Disabling IRQ #17
hda: DMA timeout retry

Quoted 2 lines

full dmesg output at
http://pcburn.com/files/Syba_serial_controller/dmesg_with_1394_disabled.txt

So the card probably generates screaming interrupt... that's bad. I found some docs for IT887x chips, according to these docs IT887x have simple interrupt controller inside. Further investigation is needed.

Can you post output of lspci -xxx ?

Signature · 2 lines
Andrey Panin		| Linux and UNIX system administrator
[email protected]		| PGP key: wwwkeys.pgp.net
#15 lore raw
Quoted 5 lines · Andrey Panin

So the card probably generates screaming interrupt... that's bad. I found some docs for IT887x chips, according to these docs IT887x have simple interrupt controller inside. Further investigation is needed.

Can you post output of lspci -xxx ?

Is it possible they put a chip on to generate a PCI interrupt on perhaps PCIB on the slot from the serial chips directly, so that they didn't have to turn interrupts from the serial chips into a signal that forces the parallel port to generate an interrupt? After all that would reduce latency, and if you use PCIA for the parallel port, PCIB for the first serial chip and PCIC for the second, you might get a much more efficient design, although the driver would have to register all those IRQs.

What IRQ is each PCI device in that system using right now? perhaps we could figure out what irq 17 would be on that PCI slot.

--
Len Sorensen

#16 lore raw
Quoted 7 lines · Lennart Sorensen
Quoted 5 lines · Andrey Panin

So the card probably generates screaming interrupt... that's bad. I found some docs for IT887x chips, according to these docs IT887x have simple interrupt controller inside. Further investigation is needed.

Can you post output of lspci -xxx ?

Quoted 7 lines

Is it possible they put a chip on to generate a PCI interrupt on perhaps PCIB on the slot from the serial chips directly, so that they didn't have to turn interrupts from the serial chips into a signal that forces the parallel port to generate an interrupt? After all that would reduce latency, and if you use PCIA for the parallel port, PCIB for the first serial chip and PCIC for the second, you might get a much more efficient design, although the driver would have to register all those IRQs.

I dont think so. IT887x has builtin interrupt controller which multiplexes 16 external IRQ pins with IRQs from builtin devices (parallel port, UARTs and GPIO) into single INTA# line. IT887x also contains 8-bit ISA-like bus and 16 chip select lines and it's all you need to glue UARTs to PCI bus.

I suspect that it's interrupt controller problem, probably edge/level triggered settings.

Quoted 2 lines

What IRQ is each PCI device in that system using right now? perhaps we could figure out what irq 17 would be on that PCI slot.

Signature · 2 lines
Andrey Panin		| Linux and UNIX system administrator
[email protected]		| PGP key: wwwkeys.pgp.net
#17 lore raw
In reply to Andrey Panin
Quoted 9 lines · Andrey Panin

On 291, 10 18, 2007 at 01:00:06 -0400, Chris Bergeron wrote:

So the card probably generates screaming interrupt... that's bad. I found some docs for IT887x chips, according to these docs IT887x have simple interrupt controller inside. Further investigation is needed.

Can you post output of lspci -xxx ?

Full output at http://pcburn.com/files/Syba_serial_controller/lspci_xxx.out. The relevant part for the Syba card is probably:

01:08.0 Serial controller: PLX Technology, Inc. Unknown device 9016 (rev 01) 00: b5 10 16 90 07 00 80 02 01 02 00 07 00 00 00 00
10: 01 a4 00 00 01 a8 00 00 01 ac 00 00 00 00 00 f5
20: 00 10 00 f5 00 20 00 f5 00 00 00 00 4e 54 08 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 05 01 00 00
40: 3f 3f 08 00 00 8c 20 8b 45 54 55 45 00 00 10 d2
50: 01 01 71 03 01 03 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 03 00 06 f8 03 f8 02
80: 78 03 78 07 00 08 00 07 00 01 20 01 40 01 60 01
90: 00 00 00 00 00 00 00 00 00 00 00 00 70 43 25 64
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

-- Chris

#18 lore raw
Quoted 23 lines · Chris Bergeron
Quoted 8 lines · Andrey Panin

On 291, 10 18, 2007 at 01:00:06 -0400, Chris Bergeron wrote:
So the card probably generates screaming interrupt... that's bad.
I found some docs for IT887x chips, according to these docs IT887x have simple interrupt controller inside. Further investigation is needed.

Can you post output of lspci -xxx ?

Full output at
http://pcburn.com/files/Syba_serial_controller/lspci_xxx.out. The relevant part for the Syba card is probably:

01:08.0 Serial controller: PLX Technology, Inc. Unknown device 9016 (rev
01)
00: b5 10 16 90 07 00 80 02 01 02 00 07 00 00 00 00
10: 01 a4 00 00 01 a8 00 00 01 ac 00 00 00 00 00 f5
20: 00 10 00 f5 00 20 00 f5 00 00 00 00 4e 54 08 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 05 01 00 00
40: 3f 3f 08 00 00 8c 20 8b 45 54 55 45 00 00 10 d2
50: 01 01 71 03 01 03 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 03 00 06 f8 03 f8 02

Quoted 8 lines

80: 78 03 78 07 00 08 00 07 00 01 20 01 40 01 60 01 90: 00 00 00 00 00 00 00 00 00 00 00 00 70 43 25 64
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Can you test an attached patch against 2.6.24-rc1 ?

Signature · 2 lines
Andrey Panin		| Linux and UNIX system administrator
[email protected]		| PGP key: wwwkeys.pgp.net
drivers/serial/8250_pci.c +95 -23
diff -urdpNX dontdiff linux-2.6.24.vanilla/drivers/serial/8250_pci.c linux-2.6.24/drivers/serial/8250_pci.c
@@ -610,45 +610,49 @@ static int pci_netmos_init(struct pci_de
 /* enable IO_Space bit */
 #define ITE_887x_POSIO_ENABLE		(1 << 31)
 
-static int pci_ite887x_init(struct pci_dev *dev)
+static int pci_ite_887x_allocate_io(struct pci_dev *dev)
 {
-	/* inta_addr are the configuration addresses of the ITE */
-	static const short inta_addr[] = { 0x2a0, 0x2c0, 0x220, 0x240, 0x1e0,
-							0x200, 0x280, 0 };
-	int ret, i, type;
-	struct resource *iobase = NULL;
-	u32 miscr, uartbar, ioport;
+	static const short inta_addr[] = {
+		0x2a0, 0x2c0, 0x220, 0x240, 0x1e0, 0x200, 0x280, 0
+	};
+	int ret, i;
 
-	/* search for the base-ioport */
-	i = 0;
-	while (inta_addr[i] && iobase == NULL) {
-		iobase = request_region(inta_addr[i], ITE_887x_IOSIZE,
-								"ite887x");
-		if (iobase != NULL) {
+	for (i = 0; i < ARRAY_SIZE(inta_addr); i++) {
+		int iobase = inta_addr[i];
+
+		if (request_region(iobase, ITE_887x_IOSIZE, "ite887x")) {
 			/* write POSIO0R - speed | size | ioport */
 			pci_write_config_dword(dev, ITE_887x_POSIO0,
 				ITE_887x_POSIO_ENABLE | ITE_887x_POSIO_SPEED |
-				ITE_887x_POSIO_IOSIZE_32 | inta_addr[i]);
+				ITE_887x_POSIO_IOSIZE_32 | iobase);
+
 			/* write INTCBAR - ioport */
-			pci_write_config_dword(dev, ITE_887x_INTCBAR, inta_addr[i]);
-			ret = inb(inta_addr[i]);
+			pci_write_config_dword(dev, ITE_887x_INTCBAR, iobase);
+			ret = inb(iobase);
 			if (ret != 0xff) {
 				/* ioport connected */
-				break;
+				return iobase;
 			}
-			release_region(iobase->start, ITE_887x_IOSIZE);
-			iobase = NULL;
+			release_region(iobase, ITE_887x_IOSIZE);
 		}
-		i++;
 	}
 
-	if (!inta_addr[i]) {
+	return 0;
+}
+
+static int pci_ite887x_init(struct pci_dev *dev)
+{
+	int i, ret, type, iobase;
+	u32 miscr, uartbar, ioport;
+
+	iobase = pci_ite_887x_allocate_io(dev);
+	if (!iobase) {
 		printk(KERN_ERR "ite887x: could not find iobase\n");
 		return -ENODEV;
 	}
 
 	/* start of undocumented type checking (see parport_pc.c) */
-	type = inb(iobase->start + 0x18) & 0x0f;
+	type = inb(iobase + 0x18) & 0x0f;
 
 	switch (type) {
 	case 0x2:	/* ITE8871 (1P) */
@@ -697,7 +701,7 @@ static int pci_ite887x_init(struct pci_d
 
 	if (ret <= 0) {
 		/* the device has no UARTs if we get here */
-		release_region(iobase->start, ITE_887x_IOSIZE);
+		release_region(iobase, ITE_887x_IOSIZE);
 	}
 
 	return ret;
@@ -712,6 +716,57 @@ static void __devexit pci_ite887x_exit(s
 	release_region(ioport, ITE_887x_IOSIZE);
 }
 
+#define ITE_887x_IRR0	0
+#define ITE_887x_IRR1	1
+#define ITE_887x_IRR2	2
+#define ITE_887x_IMR0	4
+#define ITE_887x_IMR1	5
+#define ITE_887x_IMR2	6
+#define ITE_887x_IER0	8
+#define ITE_887x_IER1	9
+#define ITE_887x_IER2	10
+#define ITE_887x_ITR0	12
+#define ITE_887x_ITR1	13
+#define ITE_887x_ITR2	14
+
+static int pci_syba_ite887x_init(struct pci_dev *dev)
+{
+	int iobase = pci_ite_887x_allocate_io(dev);
+
+	if (!iobase) {
+		printk(KERN_ERR "ite887x: could not find iobase\n");
+		return -ENODEV;
+	}
+
+	/* DEBUG */
+	printk(KERN_INFO "ite887x: io base at %#x\n", iobase);
+	printk(KERN_INFO "ite887x: IRR0=%02x IMR0=%02x IER0=%02x\n", 
+		inb(iobase + ITE_887x_IRR0), inb(iobase + ITE_887x_IMR0), inb(iobase + ITE_887x_IER0));
+	printk(KERN_INFO "ite887x: IRR1=%02x IMR1=%02x IER1=%02x\n", 
+		inb(iobase + ITE_887x_IRR1), inb(iobase + ITE_887x_IMR1), inb(iobase + ITE_887x_IER1));
+	printk(KERN_INFO "ite887x: IRR2=%02x IMR2=%02x IER2=%02x\n", 
+		inb(iobase + ITE_887x_IRR2), inb(iobase + ITE_887x_IMR2), inb(iobase + ITE_887x_IER2));
+
+	/* Clear s/w interrupt genaration register (just in case) */
+	outb(0, iobase + ITE_887x_IER0);
+	outb(0, iobase + ITE_887x_IER1);
+	outb(0, iobase + ITE_887x_IER2);
+
+	/* Clear IRQ latches */
+	outb(0, iobase + ITE_887x_IRR0);
+	outb(0, iobase + ITE_887x_IRR1);
+	outb(0, iobase + ITE_887x_IRR2);
+
+	/* Mask interrupts from on-chip devices (unused on this card) */
+	outb(0xf, iobase + ITE_887x_IMR2);
+
+	/* Set external IRQ mode to level-triggered */
+	outb(0xff, iobase + ITE_887x_IER0);
+	outb(0xff, iobase + ITE_887x_IER1);
+
+	return 8;
+}
+
 static int
 pci_default_setup(struct serial_private *priv, struct pciserial_board *board,
 		  struct uart_port *port, int idx)
@@ -797,6 +852,18 @@ static struct pci_serial_quirk pci_seria
 		.exit		= __devexit_p(pci_ite887x_exit),
 	},
 	/*
+	 * Syba
+	 */
+	{
+		.vendor		= PCI_VENDOR_ID_PLX,
+		.device		= 0x9016,
+		.subvendor	= 0x544e,
+		.subdevice	= 0x0008,
+		.init		= pci_syba_ite887x_init,
+		.setup		= pci_default_setup,
+		.exit		= __devexit_p(pci_ite887x_exit),
+	},
+	/*
 	 * Panacom
 	 */
 	{
@@ -2527,6 +2594,11 @@ static struct pci_device_id serial_pci_t
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
 		pbn_b3_8_115200 },
 
+	/* Syba PCI8871-PR8 8-port serial card */
+	{	PCI_VENDOR_ID_PLX, 0x9016,
+		0x544e, 0x0008, 0, 0,
+		pbn_b0_8_115200 },
+
 	/*
 	 * Exar Corp. XR17C15[248] Dual/Quad/Octal UART
 	 */
#19 lore raw
Quoted 7 lines · Andrey Panin
Quoted 6 lines · Chris Bergeron
Quoted 5 lines · Andrey Panin

On 291, 10 18, 2007 at 01:00:06 -0400, Chris Bergeron wrote:
So the card probably generates screaming interrupt... that's bad.
I found some docs for IT887x chips, according to these docs IT887x have simple interrupt controller inside. Further investigation is needed.

Can you point me to any of those IT887x docs? I haven't been able to dig any up myself.

Quoted 1 line

Can you test an attached patch against 2.6.24-rc1 ?

I tested basically the same patch against a current upstream tree, and the syba ports don't work, even with "irqpoll". Here's the discovery:

Serial: 8250/16550 driver16 ports, IRQ sharing enabled <FF>serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
pnp: the driver 'serial' has been registered 00:10: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial 00:10: driver attached
00:11: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A serial 00:11: driver attached
serial 0000:00:01.0: check 0x2a0
serial 0000:00:01.0: got 0x0
serial 0000:00:01.0: syba at 0x000002a0
serial 0000:00:01.0: ite887x: io base at 0x2a0 serial 0000:00:01.0: ite887x: IRR0=00 IMR0=00 IER0=00 serial 0000:00:01.0: ite887x: IRR1=00 IMR1=00 IER1=00 serial 0000:00:01.0: ite887x: IRR2=00 IMR2=00 IER2=00 0000:00:01.0: ttyS4 at I/O 0x1000 (irq = 16) is a 16550A 0000:00:01.0: ttyS5 at I/O 0x1008 (irq = 16) is a 16550A 0000:00:01.0: ttyS6 at I/O 0x1010 (irq = 16) is a 16550A 0000:00:01.0: ttyS7 at I/O 0x1018 (irq = 16) is a 16550A 0000:00:01.0: ttyS8 at I/O 0x1020 (irq = 16) is a 16550A 0000:00:01.0: ttyS9 at I/O 0x1028 (irq = 16) is a 16550A 0000:00:01.0: ttyS10 at I/O 0x1030 (irq = 16) is a 16550A 0000:00:01.0: ttyS11 at I/O 0x1038 (irq = 16) is a 16550A

The entire dmesg log is at http://helgaas.com/tmp/sybase.txt
The patch I tested is at http://helgaas.com/tmp/sybase.patch

Here's the "lspci -xxx" output:

00:01.0 Serial controller: PLX Technology, Inc. Unknown device 9016 (rev 01) 00: b5 10 16 90 03 01 80 02 01 02 00 07 00 00 00 00
10: 01 10 00 00 d1 10 00 00 c1 10 00 00 00 30 24 e8
20: 00 20 24 e8 00 10 24 e8 00 00 00 00 4e 54 08 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 00 00
40: 3f 3f 08 00 00 8c 20 8b 45 54 55 45 00 00 10 d2
50: 01 01 71 03 01 03 00 00 00 00 00 00 00 00 00 00
60: a0 02 00 e5 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 a0 02 00 00 f8 03 f8 02
80: 78 03 78 07 00 08 00 07 00 01 20 01 40 01 60 01
90: 00 00 00 00 00 00 00 00 00 00 00 00 70 43 25 64
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

#20 lore raw

Here's a 2.6.27-rc3 patch that works for me.

I only have one card, so I can't test this with multiple cards. I don't know whether there's any way the INTC_GPIO base addresses would get programmed to non-conflicting values. My card comes up with the INTC_GPIO area at I/O ports 0x0300-0x031f, but that might be a default that's just hardwired into the card.

It looks like we could allocate this region when we claim the device, which should let us support multiple cards, but I haven't tried this.

If anybody tries this out, let me know how it works.

Bjorn

drivers/serial/8250_pci.c +74 -0
index c2f2393..d442ddb 100644
@@ -737,6 +737,55 @@ static void __devexit pci_ite887x_exit(struct pci_dev *dev)
 	release_region(ioport, ITE_887x_IOSIZE);
 }
 
+#define ITE_887x_IRR0  0
+#define ITE_887x_IRR1  1
+#define ITE_887x_IRR2  2
+#define ITE_887x_IMR0  4
+#define ITE_887x_IMR1  5
+#define ITE_887x_IMR2  6
+#define ITE_887x_IER0  8
+#define ITE_887x_IER1  9
+#define ITE_887x_IER2  10
+#define ITE_887x_ITR0  12
+#define ITE_887x_ITR1  13
+#define ITE_887x_ITR2  14
+
+static int pci_syba_ite887x_init(struct pci_dev *dev)
+{
+	u32 ddma_intc_base, intc_base;
+	struct resource *iobase;
+
+	pci_read_config_dword(dev, ITE_887x_INTCBAR, &ddma_intc_base);
+	intc_base = ddma_intc_base & 0xffff;
+
+	iobase = request_region(intc_base, ITE_887x_IOSIZE, "ite887x");
+	if (!iobase) {
+		dev_err(&dev->dev, "can't request INTC_Base at 0x%x\n",
+			intc_base);
+		return -ENODEV;
+	}
+
+	outb(0x00, intc_base + ITE_887x_IMR0);	/* mask external IRQ 0-7 */
+	outb(0xff, intc_base + ITE_887x_IMR1);	/* mask external IRQ 8-15 */
+	outb(0xff, intc_base + ITE_887x_IMR2);	/* mask internal interrupts */
+
+	outb(0xff, intc_base + ITE_887x_IER0);	/* IRQ 0-7 level-triggered */
+	outb(0x00, intc_base + ITE_887x_IER1);	/* IRQ 8-15 edge (unused) */
+	outb(0x00, intc_base + ITE_887x_IER2);	/* internal edge (unused) */
+
+	outb(0x00, intc_base + ITE_887x_ITR0);	/* clear SW-generated ints */
+	outb(0x00, intc_base + ITE_887x_ITR1);
+	outb(0x00, intc_base + ITE_887x_ITR2);
+
+	outb(0x00, intc_base + ITE_887x_IRR0);	/* clear any pending ints */
+	outb(0x00, intc_base + ITE_887x_IRR1);
+	outb(0x00, intc_base + ITE_887x_IRR2);
+
+	outb(0x00, intc_base + ITE_887x_IMR0);	/* unmask external IRQ 0-7 */
+
+	return 8;
+}
+
 static int
 pci_default_setup(struct serial_private *priv, struct pciserial_board *board,
 		  struct uart_port *port, int idx)
@@ -835,6 +884,18 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = {
 		.exit		= __devexit_p(pci_ite887x_exit),
 	},
 	/*
+	 * Syba
+	 */
+	{
+		.vendor		= PCI_VENDOR_ID_PLX,
+		.device		= 0x9016,
+		.subvendor	= 0x544e,
+		.subdevice	= 0x0008,
+		.init		= pci_syba_ite887x_init,
+		.setup		= pci_default_setup,
+	/*	.exit		= __devexit_p(pci_ite887x_exit), */
+	},
+	/*
 	 * Panacom
 	 */
 	{
@@ -1085,6 +1146,8 @@ enum pci_board_num_t {
 	pbn_b0_5_115200,
 	pbn_b0_8_115200,
 
+	pbn_b0_8_460800,
+
 	pbn_b0_1_921600,
 	pbn_b0_2_921600,
 	pbn_b0_4_921600,
@@ -1226,6 +1289,12 @@ static struct pciserial_board pci_boards[] __devinitdata = {
 		.base_baud	= 115200,
 		.uart_offset	= 8,
 	},
+	[pbn_b0_8_460800] = {
+		.flags		= FL_BASE0,
+		.num_ports	= 8,
+		.base_baud	= 460800,
+		.uart_offset	= 8,
+	},
 	[pbn_b0_1_921600] = {
 		.flags		= FL_BASE0,
 		.num_ports	= 1,
@@ -2581,6 +2650,11 @@ static struct pci_device_id serial_pci_tbl[] = {
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
 		pbn_b3_8_115200 },
 
+	/* Syba PCI8871-PR8 8-port serial card */
+	{	PCI_VENDOR_ID_PLX, 0x9016,
+		0x544e, 0x0008, 0, 0,
+		pbn_b0_8_460800 },
+
 	/*
 	 * Exar Corp. XR17C15[248] Dual/Quad/Octal UART
 	 */

A message that is not in the archive (sent off-list or not yet received): [email protected]

A message that is not in the archive (sent off-list or not yet received): [email protected]

#23 lore raw

I intended to mask all the interrupts before configuring them, but an editing mistake left the UART interrupts enabled. Can you try the patch below instead?

If this doesn't work, I'll have to add some debug and try to figure out what is happening, but let's try the easy thing first.

Bjorn

drivers/serial/8250_pci.c +74 -0
index c2f2393..dc59a1f 100644
@@ -737,6 +737,55 @@ static void __devexit pci_ite887x_exit(struct pci_dev *dev)
 	release_region(ioport, ITE_887x_IOSIZE);
 }
 
+#define ITE_887x_IRR0  0
+#define ITE_887x_IRR1  1
+#define ITE_887x_IRR2  2
+#define ITE_887x_IMR0  4
+#define ITE_887x_IMR1  5
+#define ITE_887x_IMR2  6
+#define ITE_887x_IER0  8
+#define ITE_887x_IER1  9
+#define ITE_887x_IER2  10
+#define ITE_887x_ITR0  12
+#define ITE_887x_ITR1  13
+#define ITE_887x_ITR2  14
+
+static int pci_syba_ite887x_init(struct pci_dev *dev)
+{
+	u32 ddma_intc_base, intc_base;
+	struct resource *iobase;
+
+	pci_read_config_dword(dev, ITE_887x_INTCBAR, &ddma_intc_base);
+	intc_base = ddma_intc_base & 0xffff;
+
+	iobase = request_region(intc_base, ITE_887x_IOSIZE, "ite887x");
+	if (!iobase) {
+		dev_err(&dev->dev, "can't request INTC_Base at 0x%x\n",
+			intc_base);
+		return -ENODEV;
+	}
+
+	outb(0xff, intc_base + ITE_887x_IMR0);	/* mask external IRQ 0-7 */
+	outb(0xff, intc_base + ITE_887x_IMR1);	/* mask external IRQ 8-15 */
+	outb(0xff, intc_base + ITE_887x_IMR2);	/* mask internal interrupts */
+
+	outb(0xff, intc_base + ITE_887x_IER0);	/* IRQ 0-7 level-triggered */
+	outb(0x00, intc_base + ITE_887x_IER1);	/* IRQ 8-15 edge (unused) */
+	outb(0x00, intc_base + ITE_887x_IER2);	/* internal edge (unused) */
+
+	outb(0x00, intc_base + ITE_887x_ITR0);	/* clear SW-generated ints */
+	outb(0x00, intc_base + ITE_887x_ITR1);
+	outb(0x00, intc_base + ITE_887x_ITR2);
+
+	outb(0x00, intc_base + ITE_887x_IRR0);	/* clear any pending ints */
+	outb(0x00, intc_base + ITE_887x_IRR1);
+	outb(0x00, intc_base + ITE_887x_IRR2);
+
+	outb(0x00, intc_base + ITE_887x_IMR0);	/* unmask external IRQ 0-7 */
+
+	return 8;
+}
+
 static int
 pci_default_setup(struct serial_private *priv, struct pciserial_board *board,
 		  struct uart_port *port, int idx)
@@ -835,6 +884,18 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = {
 		.exit		= __devexit_p(pci_ite887x_exit),
 	},
 	/*
+	 * Syba
+	 */
+	{
+		.vendor		= PCI_VENDOR_ID_PLX,
+		.device		= 0x9016,
+		.subvendor	= 0x544e,
+		.subdevice	= 0x0008,
+		.init		= pci_syba_ite887x_init,
+		.setup		= pci_default_setup,
+	/*	.exit		= __devexit_p(pci_ite887x_exit), */
+	},
+	/*
 	 * Panacom
 	 */
 	{
@@ -1085,6 +1146,8 @@ enum pci_board_num_t {
 	pbn_b0_5_115200,
 	pbn_b0_8_115200,
 
+	pbn_b0_8_460800,
+
 	pbn_b0_1_921600,
 	pbn_b0_2_921600,
 	pbn_b0_4_921600,
@@ -1226,6 +1289,12 @@ static struct pciserial_board pci_boards[] __devinitdata = {
 		.base_baud	= 115200,
 		.uart_offset	= 8,
 	},
+	[pbn_b0_8_460800] = {
+		.flags		= FL_BASE0,
+		.num_ports	= 8,
+		.base_baud	= 460800,
+		.uart_offset	= 8,
+	},
 	[pbn_b0_1_921600] = {
 		.flags		= FL_BASE0,
 		.num_ports	= 1,
@@ -2581,6 +2650,11 @@ static struct pci_device_id serial_pci_tbl[] = {
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
 		pbn_b3_8_115200 },
 
+	/* Syba PCI8871-PR8 8-port serial card */
+	{	PCI_VENDOR_ID_PLX, 0x9016,
+		0x544e, 0x0008, 0, 0,
+		pbn_b0_8_460800 },
+
 	/*
 	 * Exar Corp. XR17C15[248] Dual/Quad/Octal UART
 	 */