mpc 860 boot linux2.6.23 problem
i am proting linux2.63.23 to mpc860t board with uboot1.1.4 as bootloader. my bootargs is root=/dev/ram rw init=/linuxrc.
i use debugger to see the regedits, find pc is run in the cpu_idle(). what is wrong with my kernel, plese give me some advice.thank you .
yours keng_629
keng_629
2007-10-15
Quoted 5 lines · keng_629 wrote:
i am proting linux2.63.23 to mpc860t board with uboot1.1.4 as bootloader. my bootargs is root=/dev/ram rw init=/linuxrc.
i use debugger to see the regedits, find pc is run in thecpu_idle(). what is wrong with my kernel, plese give me some advice.thank you .
Posting the same thing over and over again isn't going to change the response. Try head-of-Linus's-git, make sure you're using arch/powerpc, and post the device tree you're using. Without more information, we can't help you.
-Scott
Quoted 11 lines · In message <[email protected]> you wrote:
Quoted 5 lines · keng_629 wrote:
i am proting linux2.63.23 to mpc860t board with uboot1.1.4 as bootloader. my bootargs is root=/dev/ram rw init=/linuxrc.
i use debugger to see the regedits, find pc is run in thecpu_idle(). what is wrong with my kernel, plese give me some advice.thank you .Posting the same thing over and over again isn't going to change the response. Try head-of-Linus's-git, make sure you're using
arch/powerpc, and post the device tree you're using. Without more information, we can't help you.
Just to point out the obvious: U-Boot 1.1.4 is *way* too old to support any device-tree based kernel, so the fist step is to update U-Boot to a somewhat recent version (i. e. 1.3.0-rcX).
Best regards,
Wolfgang Denk
Signature · 4 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: [email protected] "Faith: not *wanting* to know what is true." - Friedrich Nietzsche
Quoted 7 lines · Wolfgang Denk
Quoted 6 lines · In message <[email protected]> you wrote:
Quoted 5 lines · keng_629 wrote:
i am proting linux2.63.23 to mpc860t board with uboot1.1.4 as bootloader. my bootargs is root=/dev/ram rw init=/linuxrc.
i use debugger to see the regedits, find pc is run in thecpu_idle(). what is wrong with my kernel, plese give me some advice.thank you .
Quoted 5 lines
Quoted 1 line
Posting the same thing over and over again isn't going to change the response. Try head-of-Linus's-git, make sure you're using
arch/powerpc, and post the device tree you're using. Without more information, we can't help you.Just to point out the obvious: U-Boot 1.1.4 is *way* too old to support any device-tree based kernel, so the fist step is to update U-Boot to a somewhat recent version (i. e. 1.3.0-rcX).
Upgrading to the latest u-boot certainly shouldn't hurt, but I don't think there's any device tree support for 8xx yet, so for now he should boot with cuImage.
-Scott
Quoted 2 lines · Scott Wood
Upgrading to the latest u-boot certainly shouldn't hurt, but I don't think there's any device tree support for 8xx yet,
Have you tried it? Works for me. In fact, most
of the development you see today was done
by Pantelis on the 8xx.
-- Dan
Quoted 9 lines · Dan Malek
Quoted 2 lines · Scott Wood
Upgrading to the latest u-boot certainly shouldn't hurt, but I don't think there's any device tree support for 8xx yet,
Have you tried it? Works for me. In fact, most
of the development you see today was done
by Pantelis on the 8xx.
I just pulled Wolfgang's latest u-boot tree, and I don't see any fdt or ft_ calls in cpu/mpc8xx, nor in any 8xx board that I recognize.
I may have been unclear in that I was talking about device tree support in u-boot, not the kernel. Obviously there's device tree support in the kernel, as evidenced by my reference to using cuImage.
-Scott
Quoted 1 line · Scott Wood
I just pulled Wolfgang's latest u-boot tree, and I don't see any fdt or
ft_calls in cpu/mpc8xx, nor in any 8xx board that I recognize.
The STx XTc 885 is supported and was used for a majority of the FT development in u-boot. I just built it a few months ago, it worked fine, so if it isn't working today the changes should be minimal to bring it up to date.
Thanks.
-- Dan
Quoted 10 lines · Dan Malek
Quoted 1 line · Scott Wood
I just pulled Wolfgang's latest u-boot tree, and I don't see any fdt or
ft_calls in cpu/mpc8xx, nor in any 8xx board that I recognize.The STx XTc 885 is supported and was used for a majority of the FT development in u-boot. I just built it a few months ago, it worked fine, so if it isn't working today the changes should be minimal to bring it up to date.
OK, that wasn't a board I recognized. :-P
Still, most 8xx boards are not yet converted AFAICT. Not that it'd be hard to do so, but it might be a bit misleading to say "upgrade u-boot and get device tree support". :-)
-Scott
A message that is not in the archive (sent off-list or not yet received): [email protected]
the problem has solved ,it is the serial cpm dug,but i don't know where it is. i used the denx linux tree,it works fine,thank you for you help. thank you
keng_629
2007-10-19
发件人: Scott Wood
发送时间: 2007-10-18 01:32:05
收件人: Dan Malek
抄送: [email protected]
主题: Re: mpc 860 boot linux2.6.23 problem
Quoted 11 lines · Dan Malek
Quoted 2 lines · Scott Wood
I just pulled Wolfgang's latest u-boot tree, and I don't see any fdt or ft_ calls in cpu/mpc8xx, nor in any 8xx board that I recognize.The STx XTc 885 is supported and was used for
a majority of the FT development in u-boot. I just built it a few months ago, it worked fine, soif it isn't working today the changes should be minimal to bring it up to date.
OK, that wasn't a board I recognized. :-P
Still, most 8xx boards are not yet converted AFAICT. Not that it'd be hard to do so, but it might be a bit misleading to say "upgrade u-boot
and get device tree support". :-)
-Scott
_______________________________________________
Linuxppc-embedded mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-embedded
Hi Scott,
Quoted 4 lines
I just pulled Wolfgang's latest u-boot tree, and I don't see any fdt or
ft_calls in cpu/mpc8xx, nor in any 8xx board that I recognize.I may have been unclear in that I was talking about device tree support in u-boot, not the kernel. Obviously there's device tree support in the kernel, as evidenced by my reference to using cuImage.
Can u-boot work on dtb trees embedded in an cuImage, at all? How would command line arguments work without a chosen node?
I tried to boot a mpc823 using the 3 argument mboot command. u-boot processed the dtb and added the chosen node correctly, however the kernel immediately oopsed with unable to access virtual memory when accessing the dtb memory as this memory was not contained in the kernel MMU space.
Thanks,
Jochen
Quoted 8 lines · Jochen Friedrich
Hi Scott,
Quoted 4 lines
I just pulled Wolfgang's latest u-boot tree, and I don't see any fdt or
ft_calls in cpu/mpc8xx, nor in any 8xx board that I recognize.I may have been unclear in that I was talking about device tree support in u-boot, not the kernel. Obviously there's device tree support in the kernel, as evidenced by my reference to using cuImage.
Can u-boot work on dtb trees embedded in an cuImage, at all?
No. If you want that, you need to use a normal uImage.
Quoted 2 lines
How would command line arguments work without a chosen node?
The bad old way: argument registers and the bd_t. The bootwrapper fills in /chosen/bootargs and other things based on that.
It's just for compatibility; use uImage if you can.
Quoted 5 lines
I tried to boot a mpc823 using the 3 argument mboot command. u-boot processed the dtb and added the chosen node correctly, however the kernel immediately oopsed with unable to access virtual memory when accessing the dtb memory as this memory was not contained in the kernel MMU space.
Make sure your version of u-boot understands the new bindings for things like brg frequency, or (less preferred) set it manually in your dts.
-Scott