ppc4xx: Add PMC440 config file

new file mode 100644
index 0000000..28f73e7
@@ -0,0 +1,497 @@
+/*
+ * (C) Copyright 2007
+ * Matthias Fuchs, esd gmbh, matthias.fuchs at esd-electronics.com.
+ * Based on the sequoia configuration file by Stefan Roese.
+ *
+ * (C) Copyright 2006-2007
+ * Stefan Roese, DENX Software Engineering, sr at denx.de.
+ *
+ * (C) Copyright 2006
+ * Jacqueline Pira-Ferriol, AMCC/IBM, jpira-ferriol at fr.ibm.com
+ * Alain Saurel,            AMCC/IBM, alain.saurel at fr.ibm.com
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/************************************************************************
+ * sequoia.h - configuration for Sequoia & Rainier boards
+ ***********************************************************************/
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*-----------------------------------------------------------------------
+ * High Level Configuration Options
+ *----------------------------------------------------------------------*/
+#define CONFIG_440EPX		1		/* Specific PPC440EPx	*/
+#define CONFIG_440		1		/* ... PPC440 family	*/
+#define CONFIG_4xx		1		/* ... PPC4xx family	*/
+
+#define CONFIG_SYS_CLK_FREQ     33333400
+
+#define CONFIG_4xx_DCACHE			/* enable dcache	*/
+
+#define CONFIG_BOARD_EARLY_INIT_F 1		/* Call board_early_init_f */
+#define CONFIG_MISC_INIT_R	1		/* Call misc_init_r	*/
+#define CONFIG_BOARD_TYPES	1	        /* support board types  */
+/*-----------------------------------------------------------------------
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ *----------------------------------------------------------------------*/
+#define CFG_MONITOR_LEN		(384  * 1024)   /* Reserve 384 kB for Monitor	*/
+#define CFG_MALLOC_LEN		(1024 * 1024)   /* Reserve 256 kB for malloc()	*/
+
+#define CONFIG_PRAM             0               /* use pram variable to overwrite */
+
+#define CFG_BOOT_BASE_ADDR	0xf0000000
+#define CFG_SDRAM_BASE		0x00000000	/* _must_ be 0		*/
+#define CFG_FLASH_BASE		0xfc000000	/* start of FLASH	*/
+#define CFG_MONITOR_BASE	TEXT_BASE
+#define CFG_NAND_ADDR		0xd0000000      /* NAND Flash		*/
+#define CFG_OCM_BASE		0xe0010000      /* ocm			*/
+#define CFG_OCM_DATA_ADDR	CFG_OCM_BASE
+#define CFG_PCI_BASE		0xe0000000      /* Internal PCI regs	*/
+#define CFG_PCI_MEMBASE		0x80000000	/* mapped pci memory	*/
+#define CFG_PCI_MEMBASE1	CFG_PCI_MEMBASE  + 0x10000000
+#define CFG_PCI_MEMBASE2	CFG_PCI_MEMBASE1 + 0x10000000
+#define CFG_PCI_MEMBASE3	CFG_PCI_MEMBASE2 + 0x10000000
+#define CFG_PCI_MEMSIZE 	0x80000000	/* 2GB! */
+
+
+/* Don't change either of these */
+#define CFG_PERIPHERAL_BASE	0xef600000	/* internal peripherals	*/
+
+#define CFG_USB2D0_BASE		0xe0000100
+#define CFG_USB_DEVICE		0xe0000000
+#define CFG_USB_HOST		0xe0000400
+#define CFG_FPGA_BASE0		0xef000000 /* 32 bit */
+#define CFG_FPGA_BASE1		0xef100000 /* 16 bit */
+
+/*-----------------------------------------------------------------------
+ * Initial RAM & stack pointer
+ *----------------------------------------------------------------------*/
+/* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache	*/
+#define CFG_INIT_RAM_ADDR	CFG_OCM_BASE	/* OCM			*/
+#define CFG_INIT_RAM_END	(4 << 10)
+#define CFG_GBL_DATA_SIZE	256		/* num bytes initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET	CFG_POST_WORD_ADDR
+
+/*-----------------------------------------------------------------------
+ * Serial Port
+ *----------------------------------------------------------------------*/
+#undef CFG_EXT_SERIAL_CLOCK	
+#define CONFIG_BAUDRATE		115200
+#define CONFIG_SERIAL_MULTI     1
+#undef CONFIG_UART1_CONSOLE /* console on front panel */
+
+#define CFG_BAUDRATE_TABLE						\
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+/*-----------------------------------------------------------------------
+ * Environment
+ *----------------------------------------------------------------------*/
+#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
+#define CFG_ENV_IS_IN_EEPROM    1	/* use FLASH for environment vars	*/
+#else
+#define CFG_ENV_IS_IN_NAND	1	/* use NAND for environment vars	*/
+#define CFG_ENV_IS_EMBEDDED	1	/* use embedded environment */
+#endif
+
+/*-----------------------------------------------------------------------
+ * RTC
+ *----------------------------------------------------------------------*/
+#define CONFIG_RTC_RX8025
+
+/*-----------------------------------------------------------------------
+ * FLASH related
+ *----------------------------------------------------------------------*/
+#define CFG_FLASH_CFI				/* The flash is CFI compatible	*/
+#define CFG_FLASH_CFI_DRIVER			/* Use common CFI driver	*/
+
+#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE }
+
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
+#define CFG_MAX_FLASH_SECT	512	/* max number of sectors on one chip	*/
+
+#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
+#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+
+#define CFG_FLASH_USE_BUFFER_WRITE 1	/* use buffered writes (20x faster)	*/
+#define CFG_FLASH_PROTECTION	1	/* use hardware flash protection	*/
+
+#define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_QUIET_TEST	1	/* don't warn upon unknown flash	*/
+
+#ifdef CFG_ENV_IS_IN_FLASH
+#define CFG_ENV_SECT_SIZE	0x20000	/* size of one complete sector		*/
+#define CFG_ENV_ADDR		((-CFG_MONITOR_LEN)-CFG_ENV_SECT_SIZE)
+#define	CFG_ENV_SIZE		0x2000	/* Total Size of Environment Sector	*/
+
+/* Address and size of Redundant Environment Sector	*/
+#define CFG_ENV_ADDR_REDUND	(CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
+#define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
+#endif
+
+#ifdef CFG_ENV_IS_IN_EEPROM
+#define CFG_ENV_OFFSET		0	/* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE		0x1000	/* 4096 bytes may be used for env vars*/
+#endif
+
+/*
+ * IPL (Initial Program Loader, integrated inside CPU)
+ * Will load first 4k from NAND (SPL) into cache and execute it from there.
+ *
+ * SPL (Secondary Program Loader)
+ * Will load special U-Boot version (NUB) from NAND and execute it. This SPL
+ * has to fit into 4kByte. It sets up the CPU and configures the SDRAM
+ * controller and the NAND controller so that the special U-Boot image can be
+ * loaded from NAND to SDRAM.
+ *
+ * NUB (NAND U-Boot)
+ * This NAND U-Boot (NUB) is a special U-Boot version which can be started
+ * from RAM. Therefore it mustn't (re-)configure the SDRAM controller.
+ *
+ * On 440EPx the SPL is copied to SDRAM before the NAND controller is
+ * set up. While still running from cache, I experienced problems accessing
+ * the NAND controller.	sr - 2006-08-25
+ */
+#define CFG_NAND_BOOT_SPL_SRC	0xfffff000	/* SPL location			*/
+#define CFG_NAND_BOOT_SPL_SIZE	(4 << 10)	/* SPL size			*/
+#define CFG_NAND_BOOT_SPL_DST	(CFG_OCM_BASE + (12 << 10)) /* Copy SPL here	*/
+#define CFG_NAND_U_BOOT_DST	0x01000000	/* Load NUB to this addr	*/
+#define CFG_NAND_U_BOOT_START	CFG_NAND_U_BOOT_DST /* Start NUB from this addr	*/
+#define CFG_NAND_BOOT_SPL_DELTA	(CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST)
+
+/*
+ * Define the partitioning of the NAND chip (only RAM U-Boot is needed here)
+ */
+#define CFG_NAND_U_BOOT_OFFS	(16 << 10)	/* Offset to RAM U-Boot image	*/
+#define CFG_NAND_U_BOOT_SIZE	(384 << 10)	/* Size of RAM U-Boot image	*/
+
+/*
+ * Now the NAND chip has to be defined (no autodetection used!)
+ */
+#define CFG_NAND_PAGE_SIZE	512		/* NAND chip page size		*/
+#define CFG_NAND_BLOCK_SIZE	(16 << 10)	/* NAND chip block size		*/
+#define CFG_NAND_PAGE_COUNT	32		/* NAND chip page count		*/
+#define CFG_NAND_BAD_BLOCK_POS	5		/* Location of bad block marker	*/
+#undef CFG_NAND_4_ADDR_CYCLE			/* No fourth addr used (<=32MB)	*/
+
+#define CFG_NAND_ECCSIZE	256
+#define CFG_NAND_ECCBYTES	3
+#define CFG_NAND_ECCSTEPS	(CFG_NAND_PAGE_SIZE / CFG_NAND_ECCSIZE)
+#define CFG_NAND_OOBSIZE	16
+#define CFG_NAND_ECCTOTAL	(CFG_NAND_ECCBYTES * CFG_NAND_ECCSTEPS)
+#define CFG_NAND_ECCPOS		{0, 1, 2, 3, 6, 7}
+
+#ifdef CFG_ENV_IS_IN_NAND
+/*
+ * For NAND booting the environment is embedded in the U-Boot image. Please take
+ * look@the file board/amcc/sequoia/u-boot-nand.lds for details.
+ */
+#define CFG_ENV_SIZE		CFG_NAND_BLOCK_SIZE
+#define CFG_ENV_OFFSET		(CFG_NAND_U_BOOT_OFFS + CFG_ENV_SIZE)
+#define CFG_ENV_OFFSET_REDUND	(CFG_ENV_OFFSET + CFG_ENV_SIZE)
+#endif
+
+/*-----------------------------------------------------------------------
+ * DDR SDRAM
+ *----------------------------------------------------------------------*/
+#define CFG_MBYTES_SDRAM        (256)		/* 256MB			*/
+#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
+#define CONFIG_DDR_DATA_EYE			/* use DDR2 optimization	*/
+#endif
+
+/*-----------------------------------------------------------------------
+ * I2C
+ *----------------------------------------------------------------------*/
+#define CONFIG_HARD_I2C		1		/* I2C with hardware support	*/
+#undef	CONFIG_SOFT_I2C				/* I2C bit-banged		*/
+#define CFG_I2C_SPEED		100000		/* I2C speed and slave address	*/
+#define CFG_I2C_SLAVE		0x7F
+
+#define CONFIG_I2C_CMD_TREE     1
+#define CONFIG_I2C_MULTI_BUS    1
+
+#define CFG_I2C_MULTI_EEPROMS
+
+#define CFG_I2C_EEPROM_ADDR	0x54
+#define CFG_I2C_EEPROM_ADDR_LEN 2
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+#define CFG_EEPROM_PAGE_WRITE_BITS 5
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
+#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x01
+
+#define CFG_EEPROM_WREN         1
+#define CFG_I2C_BOOT_EEPROM_ADDR 0x52
+
+
+/*
+ * standard dtt sensor configuration - bottom bit will determine local or
+ * remote sensor of the TMP401
+ */
+#define CONFIG_DTT_SENSORS		{ 0, 1 }
+
+/*
+ * The PMC440 uses a TI TMP401 temperature sensor. This part
+ * is basically compatible to the ADM1021 that is supported 
+ * by U-Boot.
+ *
+ * - i2c addr 0x4c
+ * - conversion rate 0x02 = 0.25 conversions/second
+ * - ALERT ouput disabled
+ * - local temp sensor enabled, min set to 0 deg, max set to 70 deg
+ * - remote temp sensor enabled, min set to 0 deg, max set to 70 deg
+ */
+#define CONFIG_DTT_ADM1021
+#define CFG_DTT_ADM1021		{ { 0x4c, 0x02, 0, 1, 70, 0, 1, 70, 0} }
+
+#define CONFIG_PREBOOT                  /* enable preboot variable      */
+
+#undef	CONFIG_BOOTARGS
+
+/* Setup some board specific values for the default environment variables */
+#define CONFIG_HOSTNAME	        pmc440
+#define CFG_BOOTFILE		"bootfile=/tftpboot/pmc440/uImage\0"
+#define CFG_ROOTPATH		"rootpath=/opt/eldk_410/ppc_4xx\0"
+
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+	CFG_BOOTFILE							\
+	CFG_ROOTPATH							\
+	"netdev=eth0\0"							\
+	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
+		"nfsroot=${serverip}:${rootpath}\0"			\
+	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
+	"addip=setenv bootargs ${bootargs} "				\
+		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
+		":${hostname}:${netdev}:off panic=1\0"			\
+	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
+	"flash_nfs=run nfsargs addip addtty;"				\
+		"bootm ${kernel_addr}\0"				\
+	"flash_self=run ramargs addip addtty;"				\
+		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
+	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"     \
+	        "bootm\0"						\
+	"kernel_addr=FC000000\0"					\
+	"ramdisk_addr=FC180000\0"					\
+	"load=tftp 200000 /tftpboot/pmc440/u-boot.bin\0"		\
+	"update=protect off FFFA0000 FFFFFFFF;era FFFA0000 FFFFFFFF;"	\
+		"cp.b 200000 FFFA0000 60000\0"			        \
+	""
+
+#define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds	*/
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
+#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
+
+#define	CONFIG_IBM_EMAC4_V4	1
+#define CONFIG_MII		1	/* MII PHY management		*/
+#define CONFIG_PHY_ADDR		0	/* PHY address, See schematics	*/
+
+#define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
+
+#define CONFIG_HAS_ETH0
+#define CFG_RX_ETH_BUFFER	32	/* Number of ethernet rx buffers & descriptors */
+
+#define CONFIG_NET_MULTI	1
+#define CONFIG_HAS_ETH1		1	/* add support for "eth1addr"	*/
+#define CONFIG_PHY1_ADDR	1
+#define CONFIG_RESET_PHY_R      1
+
+/* USB */
+#define CONFIG_USB_OHCI_NEW
+#define CONFIG_USB_STORAGE
+#define CFG_OHCI_BE_CONTROLLER
+
+#undef CFG_USB_OHCI_BOARD_INIT
+#define CFG_USB_OHCI_CPU_INIT	1
+#define CFG_USB_OHCI_REGS_BASE	CFG_USB_HOST
+#define CFG_USB_OHCI_SLOT_NAME	"ppc440"
+#define CFG_USB_OHCI_MAX_ROOT_PORTS 15
+
+/* Comment this out to enable USB 1.1 device */
+#define USB_2_0_DEVICE
+
+/* Partitions */
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+#define CONFIG_ISO_PARTITION
+
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_BSP
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DTT
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_USB
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SDRAM
+
+/* POST support */
+#define CONFIG_POST		(CFG_POST_MEMORY   | \
+				 CFG_POST_CPU	   | \
+				 CFG_POST_UART	   | \
+				 CFG_POST_I2C	   | \
+				 CFG_POST_CACHE	   | \
+				 CFG_POST_FPU      | \
+				 CFG_POST_ETHER	   | \
+				 CFG_POST_SPR)
+
+#define CFG_POST_WORD_ADDR	(CFG_GBL_DATA_OFFSET - 0x4)
+#define CONFIG_LOGBUFFER
+#define CFG_POST_CACHE_ADDR	0x10000000 /* free virtual address	*/
+
+#define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
+
+#define CONFIG_SUPPORT_VFAT
+
+/*-----------------------------------------------------------------------
+ * Miscellaneous configurable options
+ *----------------------------------------------------------------------*/
+#define CFG_LONGHELP			/* undef to save memory		*/
+#define CFG_PROMPT	        "=> "	/* Monitor Command Prompt	*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE	        1024	/* Console I/O Buffer Size	*/
+#else
+#define CFG_CBSIZE	        256	/* Console I/O Buffer Size	*/
+#endif
+#define CFG_PBSIZE              (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS	        16	/* max number of command args	*/
+#define CFG_BARGSIZE	        CFG_CBSIZE /* Boot Argument Buffer Size	*/
+
+#define CFG_MEMTEST_START	0x0400000 /* memtest works on		*/
+#define CFG_MEMTEST_END		0x0C00000 /* 4 ... 12 MB in DRAM	*/
+
+#define CFG_LOAD_ADDR		0x100000  /* default load address	*/
+#define CFG_EXTBDINFO		1	/* To use extended board_into (bd_t) */
+
+#define CFG_HZ		        1000	/* decrementer freq: 1 ms ticks	*/
+
+#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
+#define CONFIG_LOOPW            1       /* enable loopw command         */
+#define CONFIG_MX_CYCLIC        1       /* enable mdc/mwc commands      */
+#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
+#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *----------------------------------------------------------------------*/
+/* General PCI */
+#define CONFIG_PCI			/* include pci support	        */
+#define CONFIG_PCI_PNP			/* do (not) pci plug-and-play   */
+#define CFG_PCI_CACHE_LINE_SIZE	0       /* to avoid problems with PNP   */
+#define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup  */
+#define CFG_PCI_TARGBASE        0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE*/
+
+/* Board-specific PCI */
+#define CFG_PCI_TARGET_INIT
+#define CFG_PCI_MASTER_INIT
+
+/* PCI identification */
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE  /* PCI Vendor ID: esd gmbh      */
+#define CFG_PCI_SUBSYS_ID_NONMONARCH 0x0441  /* PCI Device ID: Non-Monarch */
+#define CFG_PCI_SUBSYS_ID_MONARCH 0x0440     /* PCI Device ID: Monarch */
+#define CFG_PCI_CLASSCODE_NONMONARCH    PCI_CLASS_PROCESSOR_POWERPC
+#define CFG_PCI_CLASSCODE_MONARCH       PCI_CLASS_BRIDGE_HOST
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * FPGA stuff
+ *----------------------------------------------------------------------*/
+#if 0 /* disabled until my FPGA changes will get it into U-Boot :-) */
+#define CONFIG_FPGA
+#define CONFIG_FPGA_XILINX
+#define CONFIG_FPGA_SPARTAN2
+#define CONFIG_FPGA_SPARTAN3
+
+#define CONFIG_FPGA_COUNT       2
+#endif
+/*-----------------------------------------------------------------------
+ * External Bus Controller (EBC) Setup
+ *----------------------------------------------------------------------*/
+
+/*
+ * On Sequoia CS0 and CS3 are switched when configuring for NAND booting
+ */
+#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
+#define CFG_NAND_CS		2		/* NAND chip connected to CSx	*/
+
+/* Memory Bank 0 (NOR-FLASH) initialization					*/
+#define CFG_EBC_PB0AP		0x03017200
+#define CFG_EBC_PB0CR		(CFG_FLASH_BASE | 0xda000)
+
+/* Memory Bank 2 (NAND-FLASH) initialization					*/
+#define CFG_EBC_PB2AP		0x018003c0
+#define CFG_EBC_PB2CR		(CFG_NAND_ADDR | 0x1c000)
+#else
+#define CFG_NAND_CS		0		/* NAND chip connected to CSx	*/
+/* Memory Bank 2 (NOR-FLASH) initialization					*/
+#define CFG_EBC_PB2AP		0x03017200
+#define CFG_EBC_PB2CR		(CFG_FLASH_BASE | 0xda000)
+
+/* Memory Bank 0 (NAND-FLASH) initialization					*/
+#define CFG_EBC_PB0AP		0x018003c0
+#define CFG_EBC_PB0CR		(CFG_NAND_ADDR | 0x1c000)
+#endif
+
+/* Memory Bank 4 (FPGA / 32Bit) initialization						*/
+#define CFG_EBC_PB4AP		0x03840f40 /* BME=0,TWT=7,CSN=1,TH=7,RE=1,SOR=0,BEM=1 */
+#define CFG_EBC_PB4CR		(CFG_FPGA_BASE0 | 0x1c000) /* BS=1M,BU=R/W,BW=32bit */
+
+/* Memory Bank 5 (FPGA / 16Bit) initialization						*/
+#define CFG_EBC_PB5AP		0x03840f40 /* BME=0,TWT=3,CSN=1,TH=0,RE=1,SOR=0,BEM=1 */
+#define CFG_EBC_PB5CR		(CFG_FPGA_BASE1 | 0x1a000) /* BS=1M,BU=R/W,BW=16bit */ 
+
+/*-----------------------------------------------------------------------
+ * NAND FLASH
+ *----------------------------------------------------------------------*/
+#define CFG_MAX_NAND_DEVICE	1
+#define NAND_MAX_CHIPS		1
+#define CFG_NAND_BASE		(CFG_NAND_ADDR + CFG_NAND_CS)
+#define CFG_NAND_SELECT_DEVICE  1	/* nand driver supports mutipl. chips	*/
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
+#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2	    /* which serial port to use */
+#endif
+#endif	/* __CONFIG_H */