ide-{floppy,tape}: remove debug code for dumping identify data
PATCH 2/2 ide-{floppy,tape}: remove debug code for dumping identify data
IDE core supports dumping raw identify data in hdparm friendly format now so verbose identify dumping in ide-{floppy,tape}.c device drivers (done iff IDE{FLOPPY,TAPE}_DEBUG_INFO is defined to '1' and it is '0' by default) is no longer nedeed.
Signed-off-by Bartlomiej Zolnierkiewicz <[email protected]>
--- drivers/ide/ide-floppy.c | 50 --------------------------------------- drivers/ide/ide-tape.c | 59 ----------------------------------------------- 2 files changed, 109 deletions(-)
drivers/ide/ide-floppy.c +0 -50
@@ -1658,7 +1658,6 @@ static int idefloppy_identify_device (id {struct idefloppy_id_gcw gcw;#if IDEFLOPPY_DEBUG_INFO -u16 mask,i;char buffer[80 ];#endif /* IDEFLOPPY_DEBUG_INFO */
@@ -1705,55 +1704,6 @@ static int idefloppy_identify_device (id default: sprintf(buffer, "Reserved");break; }printk (KERN_INFO "Command Packet Size: %s\n" , buffer); -printk (KERN_INFO "Model: %.40s\n" ,id->model); -printk (KERN_INFO "Firmware Revision: %.8s\n" ,id->fw_rev); -printk (KERN_INFO "Serial Number: %.20s\n" ,id->serial_no); -printk (KERN_INFO "Write buffer size(?): %d bytes\n" ,id->buf_size*512 ); -printk (KERN_INFO "DMA: %s" ,id->capability &0x01 ?"Yes\n" :"No\n" ); -printk (KERN_INFO "LBA: %s" ,id->capability &0x02 ?"Yes\n" :"No\n" ); -printk (KERN_INFO "IORDY can be disabled: %s" ,id->capability &0x04 ?"Yes\n" :"No\n" ); -printk (KERN_INFO "IORDY supported: %s" ,id->capability &0x08 ?"Yes\n" :"Unknown\n" ); -printk (KERN_INFO "ATAPI overlap supported: %s" ,id->capability &0x20 ?"Yes\n" :"No\n" ); -printk (KERN_INFO "PIO Cycle Timing Category: %d\n" ,id->tPIO); -printk (KERN_INFO "DMA Cycle Timing Category: %d\n" ,id->tDMA); -printk (KERN_INFO "Single Word DMA supported modes:\n" ); -for (i=0 ,mask=1 ;i<8 ;i++,mask=mask <<1 ) { -if (id->dma_1word & mask) -printk (KERN_INFO " Mode %d%s\n" , i, - (id->dma_1word & (mask <<8 )) ?" (active)" :"" ); - } -printk (KERN_INFO "Multi Word DMA supported modes:\n" ); -for (i=0 ,mask=1 ;i<8 ;i++,mask=mask <<1 ) { -if (id->dma_mword & mask) -printk (KERN_INFO " Mode %d%s\n" , i, - (id->dma_mword & (mask <<8 )) ?" (active)" :"" ); - } -if (id->field_valid &0x0002 ) { -printk (KERN_INFO "Enhanced PIO Modes: %s\n" , - id->eide_pio_modes &1 ?"Mode 3" :"None" ); -if (id->eide_dma_min ==0 ) -sprintf (buffer,"Not supported" ); -else -sprintf (buffer,"%d ns" ,id->eide_dma_min); -printk (KERN_INFO "Minimum Multi-word DMA cycle per word: %s\n" , buffer); -if (id->eide_dma_time ==0 ) -sprintf (buffer,"Not supported" ); -else -sprintf (buffer,"%d ns" ,id->eide_dma_time); -printk (KERN_INFO "Manufacturer\'s Recommended Multi-word cycle: %s\n" , buffer); -if (id->eide_pio ==0 ) -sprintf (buffer,"Not supported" ); -else -sprintf (buffer,"%d ns" ,id->eide_pio); -printk (KERN_INFO "Minimum PIO cycle without IORDY: %s\n" , - buffer); -if (id->eide_pio_iordy ==0 ) -sprintf (buffer,"Not supported" ); -else -sprintf (buffer,"%d ns" ,id->eide_pio_iordy); -printk (KERN_INFO "Minimum PIO cycle with IORDY: %s\n" , buffer); - }else -printk (KERN_INFO "According to the device, fields 64-70 are not valid.\n" );#endif /* IDEFLOPPY_DEBUG_INFO */ if (gcw.protocol !=2 )
drivers/ide/ide-tape.c +0 -59
71 lines not on this page · raw message