arm64: dts: rockchip: Fix microSD in Sapphire board
Subsystems (2)
PATCH 1/1 arm64: dts: rockchip: Fix microSD in Sapphire board
The microSD card slot in the Sapphire board is not working because of several issues:
1.- The vmmc power supply is missing in the DTS. It is capable of 3.0V and has a GPIO-based enable control.
2.- The vqmmc power supply can provide up to 3.3V, but it is capped in the DTS to just 3.0V because of the vmmc capability. This results in a conflict from the mmc driver requesting an unsupportable voltage range from 3.3V to 3.0V (min > max) as reported in dmesg. So, extend the range up to 3.3V. The hw should be able to stand this 0.3V tolerance. See mmc_regulator_set_vqmmc in drivers/mmc/core/core.c.
3.- The card detect signal is non-working. There is a known conflict with jtag, but the workaround in drivers/soc/rockchip/grf.c does not work. Adding the broken-cd attribute to the DTS fixes the issue.
--- .../boot/dts/rockchip/rk3399-sapphire.dtsi | 24 ++++++++++++++++++- 1 file changed, 23 insertions(+), 1 deletion(-)
arch/arm64/boot/dts/rockchip/rk3399-sapphire.dtsi +23 -1
@@ -130,6 +130,19 @@ vin-supply = <&vcc_1v8>; }; + vcc3v0_sd: vcc3v0-sd { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio0 RK_PA1 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc0_pwr_h>; + regulator-always-on; + regulator-max-microvolt = <3000000>; + regulator-min-microvolt = <3000000>; + regulator-name = "vcc3v0_sd"; + vin-supply = <&vcc3v3_sys>; + }; + vcc3v3_sys: vcc3v3-sys { compatible = "regulator-fixed"; regulator-name = "vcc3v3_sys";
@@ -343,7 +356,7 @@ regulator-always-on; regulator-boot-on; regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; regulator-state-mem { regulator-on-in-suspend; regulator-suspend-microvolt = <3000000>;
@@ -503,6 +516,13 @@ }; }; + sd { + sdmmc0_pwr_h: sdmmc0-pwr-h { + rockchip,pins = + <RK_GPIO0 RK_PA1 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + usb2 { vcc5v0_host_en: vcc5v0-host-en { rockchip,pins =
@@ -533,6 +553,7 @@ }; &sdmmc { + broken-cd; bus-width = <4>; cap-mmc-highspeed; cap-sd-highspeed;
@@ -541,6 +562,7 @@ max-frequency = <150000000>; pinctrl-names = "default"; pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>; + vmmc-supply = <&vcc3v0_sd>; vqmmc-supply = <&vcc_sdio>; status = "okay"; };
Signature · 1 line
2.19.0
A message that is not in the archive (sent off-list or not yet received): 20180917134714.2197-1-vicencb-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org
Am Montag, 17. September 2018, 15:47:14 CEST schrieb Vicente Bergas:
Quoted 14 lines
The microSD card slot in the Sapphire board is not working because of several issues:
1.- The vmmc power supply is missing in the DTS. It is capable of 3.0V and has a GPIO-based enable control.
2.- The vqmmc power supply can provide up to 3.3V, but it is capped in the DTS to just 3.0V because of the vmmc capability. This results in a conflict from the mmc driver requesting an unsupportable voltage range from 3.3V to 3.0V (min > max) as reported in dmesg. So, extend the range up to 3.3V. The hw should be able to stand this 0.3V tolerance. Seemmc_regulator_set_vqmmcindrivers/mmc/core/core.c.
3.- The card detect signal is non-working. There is a known conflict with jtag, but the workaround indrivers/soc/rockchip/grf.cdoes not work. Adding the broken-cd attribute to the DTS fixes the issue.
Quoted 1 line
Signed-off-by Vicente Bergas <[email protected]>
applied for 4.20
Thanks
Heiko