2.6.24-rc6-git12: Reported regressions from 2.6.23
This message contains a list of some regressions from 2.6.23 reported since 2.6.24-rc1 was released, for which there are no fixes in the mainline I know of. If any of them have been fixed already, please let me know.
If you know of any other unresolved regressions from 2.6.23, please let me know either and I'll add them to the list. Also, please let me know if any of the entries below are invalid.
Listed regressions statistics:
Date Total Pending Unresolved
----------------------------------------
Today 139 28 15 2008-01-01 139 38 23 2007-12-21 118 21 13 2007-12-18 115 29 15 2007-12-12 106 31 17 2007-12-08 98 29 19 2007-12-01 85 29 18 2007-11-24 75 25 21 2007-11-19 68 26 21 2007-11-17 65 25 20
Unresolved regressions
----------------------
Subject : EHCI causes system to resume instantly from S4
Submitter : Maxim Levitsky <[email protected]>
Date : 2007-10-28 14:56
References : http://lkml.org/lkml/2007/10/27/66
http://bugzilla.kernel.org/show_bug.cgi?id=9258
David Brownell <[email protected]> Alan Stern <[email protected]>
Workaround : http://bugzilla.kernel.org/show_bug.cgi?id=9258#c30
Subject : SError: { DevExch } occuring and causing disruption
Submitter : Avuton Olrich <[email protected]>
Date : 2007-11-15 22:39
References : http://bugzilla.kernel.org/show_bug.cgi?id=9393
Mark Lord <[email protected]>
Subject : 20000+ wake-ups/second in 2.6.24
Submitter : Mark Lord <[email protected]>
Date : 2007-12-02 04:23
References : http://lkml.org/lkml/2007/12/1/141
http://bugzilla.kernel.org/show_bug.cgi?id=9489
Subject : soft lockup - CPU#1 stuck for 15s! [swapper:0]
Submitter : "Parag Warudkar" <[email protected]>
Date : 2007-12-07 18:14
References : http://lkml.org/lkml/2007/12/7/299
http://bugzilla.kernel.org/show_bug.cgi?id=9525
Thomas Gleixner <[email protected]> Ingo Molnar <[email protected]>
Subject : BUG: bad unlock balance detected!
Submitter : Krzysztof Oledzki <[email protected]>
Date : 2007-12-11 03:17
References : http://bugzilla.kernel.org/show_bug.cgi?id=9542
Herbert Xu <[email protected]>
Subject : PATA_HPT37X embezzles two ports
Submitter : "Bjoern Olausson" <[email protected]>
Date : 2007-12-12 11:05
References : http://lkml.org/lkml/2007/12/12/161
http://bugzilla.kernel.org/show_bug.cgi?id=9551
Handled-By :
Subject : Could not set non-blocking flag with 2.6.24-rc5
Submitter : Tino Keitel <[email protected]>
Date : 2007-12-13 16:27
References : http://lkml.org/lkml/2007/12/13/392
http://bugzilla.kernel.org/show_bug.cgi?id=9557
Handled-By :
Subject : swapping in 2.6.24-rc5-git3
Submitter : Lukas Hejtmanek <[email protected]>
Date : 2007-12-17 14:04
References : http://lkml.org/lkml/2007/12/17/98
http://bugzilla.kernel.org/show_bug.cgi?id=9592
Subject : Problems on booting
Submitter : "werner" <[email protected]>
Date : 2007-12-22 14:29
References : http://lkml.org/lkml/2007/12/22/110
http://bugzilla.kernel.org/show_bug.cgi?id=9621
Handled-By :
Subject : ACPI or radeon: spontaneous reboot regression
Submitter : Matt Mackall <[email protected]>
Date : 2007-12-22 16:09
References : http://lkml.org/lkml/2007/12/22/139
http://bugzilla.kernel.org/show_bug.cgi?id=9624
Handled-By :
Subject : iptables won't work
Submitter : Kristoffer Malmström <[email protected]>
Date : 2007-12-28
References : http://bugzilla.kernel.org/show_bug.cgi?id=9657
Subject : in 2.6.24-rc6 function keys stopped working - toshiba u300-13m, FSC V5505
Submitter : Keepa Mihail Sergeevich <[email protected]>
Date : 2007-12-29 16:07
References : http://bugzilla.kernel.org/show_bug.cgi?id=9663
Subject : lockdep warning with LTP dio test (v2.6.24-rc6-125-g5356f66)
Submitter : Erez Zadok <[email protected]>
Date : 2007-12-24 18:02
References : http://lkml.org/lkml/2007/12/24/107
http://bugzilla.kernel.org/show_bug.cgi?id=9670
Handled-By :
Subject : IDE/ACPI related hibernation regression: Second attempt fails
Submitter : Mikko Vinni <[email protected]>
Date : 2007-12-31 13:27
References : http://lkml.org/lkml/2007/12/31/135
http://bugzilla.kernel.org/show_bug.cgi?id=9673
Subject : kexec buffer error
Submitter : Randy Dunlap <[email protected]>
Date : 2008-01-04 22:54
References : http://lkml.org/lkml/2008/1/4/255
http://bugzilla.kernel.org/show_bug.cgi?id=9693
Handled-By :
Regressions with patches
------------------------
Subject : [2.6.24-rc6] pdflush still stuck in D state regression
Submitter : "Tvrtko A. Ursulin" <[email protected]>
Date : 2007-11-02 09:54
References : http://bugzilla.kernel.org/show_bug.cgi?id=9291
Patch : http://bugzilla.kernel.org/attachment.cgi?id=14219&action=view
Subject : snd_hda_intel 2.6.24-rc2 bug: interrupts don't always work on Lenovo X60s
Submitter : Roland Dreier <[email protected]>
Date : 2007-11-08 14:55
References : http://lkml.org/lkml/2007/11/8/255
http://bugzilla.kernel.org/show_bug.cgi?id=9332
Ingo Molnar <[email protected]>
Patch : http://lkml.org/lkml/2007/11/16/66
Subject : jiffies counter leaps in 2.6.24-rc3
Submitter : Stefano Brivio <[email protected]>
Date : 2007-11-29 08:36
References : http://lkml.org/lkml/2007/11/24/53
http://bugzilla.kernel.org/show_bug.cgi?id=9475
Patch : http://lkml.org/lkml/2007/12/7/132
Subject : Battery shows up twice in kpowersave
Submitter : Rolf Eike Beer <[email protected]>
Date : 2007-12-03 12:06
References : http://bugzilla.kernel.org/show_bug.cgi?id=9494
Patch : http://bugzilla.kernel.org/attachment.cgi?id=14137&action=view
Subject : 2.6.24-rc4 hwmon it87 probe fails
Submitter : Mike Houston <[email protected]>
Date : 2007-12-06 17:10
References : http://lkml.org/lkml/2007/12/4/466
http://bugzilla.kernel.org/show_bug.cgi?id=9514
Patch : http://bugzilla.kernel.org/attachment.cgi?id=14267&action=view
Subject : RTNL: assertion failed at net/ipv6/addrconf.c (2164)/RTNL: assertion failed at net/ipv4/devinet.c (1055)
Submitter : Krzysztof Oledzki <[email protected]>
Date : 2007-12-11 03:20
References : http://bugzilla.kernel.org/show_bug.cgi?id=9543
Herbert Xu <[email protected]> Jay Vosburgh <[email protected]>
Patch : http://bugzilla.kernel.org/show_bug.cgi?id=9543#c6
Subject : Regression: Battery method parse error
Submitter : Bruce Duncan <[email protected]>
Date : 2007-12-23 13:00
References : http://bugzilla.kernel.org/show_bug.cgi?id=9627
Patch : http://bugzilla.kernel.org/attachment.cgi?id=14181&action=view
Subject : 2.6.24-rc6 2.6.24-rc3 qstor timeouts during probe
Submitter : Alan Young <[email protected]>
Date : 2007-12-24 15:17
References : http://bugzilla.kernel.org/show_bug.cgi?id=9631
Patch : http://bugzilla.kernel.org/attachment.cgi?id=14259&action=view
Subject : Unaligned accesses in xfs_file_readdir
Submitter : Dustin Marquess <[email protected]>
Date : 2007-12-25 17:47
References : http://bugzilla.kernel.org/show_bug.cgi?id=9635
Patch : http://bugzilla.kernel.org/attachment.cgi?id=14255&action=view
Subject : restore ARMv6 OProfile support
Submitter : Adrian Bunk <[email protected]>
Date : 2007-12-28 11:39
References : http://bugzilla.kernel.org/show_bug.cgi?id=9653
http://lkml.org/lkml/2007/12/28/99
Patch : http://lkml.org/lkml/2007/12/29/111
Subject : restore blackfin HARDWARE_PM support
Submitter : Adrian Bunk <[email protected]>
Date : 2007-12-28 11:40
References : http://lkml.org/lkml/2007/12/28/100
http://bugzilla.kernel.org/show_bug.cgi?id=9654
Patch : http://lkml.org/lkml/2007/12/29/75
Subject : Booting from nfsroot fails
Submitter : Puzin, Dimitri <[email protected]>
Date : 2007-12-29 11:54
References : http://bugzilla.kernel.org/show_bug.cgi?id=9661
Patch : http://bugzilla.kernel.org/attachment.cgi?id=14224&action=view
Subject : max_cstate VMware regression
Submitter : Mark Lord <[email protected]>
Date : 2008-01-03 14:54
References : http://lkml.org/lkml/2008/1/2/328
http://bugzilla.kernel.org/show_bug.cgi?id=9683
Patch : http://lkml.org/lkml/2008/1/3/399
For details, please follow the links given in references.
As you can see, there is a Bugzilla entry for each of the listed regressions. There also is a Bugzilla entry used for tracking the regressions from 2.6.23, unresolved as well as resolved, at:
http://bugzilla.kernel.org/show_bug.cgi?id=9243
Please let me know if there are any Bugzilla entries that should be added to the list in there.
Thanks,
Rafael
Quoted 5 lines
Subject :
PATA_HPT37Xembezzles two ports
Submitter : "Bjoern Olausson" <[email protected]>
Date : 2007-12-12 11:05
References : http://lkml.org/lkml/2007/12/12/161http://bugzilla.kernel.org/show_bug.cgi?id=9551
HPT374 patch was posted.
We also have a newly reported regression in USB pl2303
See [pl2303 regression] Linux 2.6.23 breaks gpsbabel's DG-100 support on [email protected]
No bug # yet but will try and sort a patch out next week.
Quoted 7 lines · Alan Cox
Quoted 5 lines
Subject :
PATA_HPT37Xembezzles two ports
Submitter : "Bjoern Olausson" <[email protected]>
Date : 2007-12-12 11:05
References : http://lkml.org/lkml/2007/12/12/161http://bugzilla.kernel.org/show_bug.cgi?id=9551HPT374 patch was posted.
Udated status, thanks.
Quoted 6 lines
We also have a newly reported regression in USB pl2303
See [pl2303 regression] Linux 2.6.23 breaks gpsbabel's DG-100 support on [email protected]
No bug # yet but will try and sort a patch out next week.
Well, that's not a regression from 2.6.23.
Quoted 3 lines · Rafael J. Wysocki
This message contains a list of some regressions from 2.6.23 reported since 2.6.24-rc1 was released, for which there are no fixes in the mainline I know of. If any of them have been fixed already, please let me know.
..
Quoted 7 lines
Subject : 20000+ wake-ups/second in 2.6.24
Submitter : Mark Lord <[email protected]>
Date : 2007-12-02 04:23
References : http://lkml.org/lkml/2007/12/1/141http://bugzilla.kernel.org/show_bug.cgi?id=9489Handled-By Arjan van de Ven <[email protected]>
..
I have only seen that one once, and I think it was Arjan who said that it has been observed rarely by other people as well. The bugzilla entry is mostly just to track the darned thing, but it seems unlikely that anyone will find/fix it for 2.6.24. No big deal, but it would be good to have somebody knowledgeable in clocks/interrupts try and track it down.
I wonder if it's just a babbling IRQ on resume, before the driver has run it's resume code or something ?
Cheers
Quoted 21 lines · Mark Lord
Quoted 3 lines · Rafael J. Wysocki
This message contains a list of some regressions from 2.6.23 reported since 2.6.24-rc1 was released, for which there are no fixes in the mainline I know of. If any of them have been fixed already, please let me know.
..
Quoted 7 lines
Subject : 20000+ wake-ups/second in 2.6.24
Submitter : Mark Lord <[email protected]>
Date : 2007-12-02 04:23
References : http://lkml.org/lkml/2007/12/1/141http://bugzilla.kernel.org/show_bug.cgi?id=9489Handled-By Arjan van de Ven <[email protected]>..
I have only seen that one once, and I think it was Arjan who said that it has been observed rarely by other people as well. The bugzilla entry is mostly just to track the darned thing, but it seems unlikely that anyone will find/fix it for 2.6.24. No big deal, but it would be good to have somebody knowledgeable in clocks/interrupts try and track it down.
Quoted 2 lines
I wonder if it's just a babbling IRQ on resume, before the driver has run it's resume code or something ?
i've read the discussions, and i cannot see it analyzed anywhere _what_ causes the wakeups. And how are these wakeups counted? Is this based on powertop output:
Wakeups-from-idle per second : 20.4 interval: 1.8s
? Somewhere i saw it mentioned that "the CPU throws out of C mode". What does that mean - does it mean we try to idle again and again, but we immediately return from C mode - while this all looks like "idle" time to the scheduler (so 'top' will show lots of idle time), but the ACPI wakeup counters are going up like mad? What is /proc/interrupts doing when this happens - is any of the irq sources going upwards?
Ingo
Quoted 26 lines · On Sun, 6 Jan 2008 10:55:01 +0100 Ingo Molnar <[email protected]> wrote:
Quoted 14 lines · Mark Lord
Quoted 4 lines · Rafael J. Wysocki
This message contains a list of some regressions from 2.6.23 reported since 2.6.24-rc1 was released, for which there are no fixes in the mainline I know of. If any of them have been fixed already, please let me know.
..
Quoted 7 lines
Subject : 20000+ wake-ups/second in 2.6.24
Submitter : Mark Lord <[email protected]>
Date : 2007-12-02 04:23
References : http://lkml.org/lkml/2007/12/1/141http://bugzilla.kernel.org/show_bug.cgi?id=9489Handled-By Arjan van de Ven <[email protected]>Quoted 2 lines
I wonder if it's just a babbling IRQ on resume, before the driver has run it's resume code or something ?
i've read the discussions, and i cannot see it analyzed anywhere _what_ causes the wakeups. And how are these wakeups counted? Is this based on powertop output:
Wakeups-from-idle per second : 20.4 interval: 1.8s
Quoted 8 lines
? Somewhere i saw it mentioned that "the CPU throws out of C mode". What does that mean - does it mean we try to idle again and again, but we immediately return from C mode - while this all looks like "idle" time to the scheduler (so 'top' will show lots of idle time), but the ACPI wakeup counters are going up like mad? What is
/proc/interruptsdoing when this happens - is any of the irq sources going upwards?
what seems to happen (and this is based on seeing this on my own devel laptop, as well as several other reports; Mark is by far not the only one) is something hardware related, it's been seen on lots of different kernel versions.
It seems to mostly (but not 100%) happen with TI cardbus bridges, where for some reason, once the yenta driver is loaded (unloading it later makes no difference), once in a while we get into a mode where the CPU always immediately goes out of the C-state again. On a hardware level, there are only a few things that cause a CPU to exit a C-state, and one of them is a pending interrupt of some kind, which is the most likely thing going on here; some device or apic being stuck with interrupt high, but somehow the CPU isn't actually seeing the interrupt itself (or has it blocked!)
To call this a 2.6.24 regression is a mistake (as I've said before), it's not new to .24 by any means.
Signature · 3 lines
If you want to reach me at my work email, use [email protected] For development, discussion and tips for power savings, visit http://www.lesswatts.org
Quoted 50 lines · Arjan van de Ven
Quoted 26 lines · On Sun, 6 Jan 2008 10:55:01 +0100 Ingo Molnar <[email protected]> wrote:
Quoted 14 lines · Mark Lord
Quoted 4 lines · Rafael J. Wysocki
This message contains a list of some regressions from 2.6.23 reported since 2.6.24-rc1 was released, for which there are no fixes in the mainline I know of. If any of them have been fixed already, please let me know.
..
Quoted 7 lines
Subject : 20000+ wake-ups/second in 2.6.24
Submitter : Mark Lord <[email protected]>
Date : 2007-12-02 04:23
References : http://lkml.org/lkml/2007/12/1/141http://bugzilla.kernel.org/show_bug.cgi?id=9489Handled-By Arjan van de Ven <[email protected]>Quoted 2 lines
I wonder if it's just a babbling IRQ on resume, before the driver has run it's resume code or something ?
i've read the discussions, and i cannot see it analyzed anywhere _what_ causes the wakeups. And how are these wakeups counted? Is this based on powertop output:
Wakeups-from-idle per second : 20.4 interval: 1.8s
Quoted 8 lines
? Somewhere i saw it mentioned that "the CPU throws out of C mode". What does that mean - does it mean we try to idle again and again, but we immediately return from C mode - while this all looks like "idle" time to the scheduler (so 'top' will show lots of idle time), but the ACPI wakeup counters are going up like mad? What is
/proc/interruptsdoing when this happens - is any of the irq sources going upwards?what seems to happen (and this is based on seeing this on my own devel laptop, as well as several other reports; Mark is by far not the only one) is something hardware related, it's been seen on lots of different kernel versions.
It seems to mostly (but not 100%) happen with TI cardbus bridges, where for some reason, once the yenta driver is loaded (unloading it later makes no difference), once in a while we get into a mode where the CPU always immediately goes out of the C-state again. On a hardware level, there are only a few things that cause a CPU to exit a C-state, and one of them is a pending interrupt of some kind, which is the most likely thing going on here; some device or apic being stuck with interrupt high, but somehow the CPU isn't actually seeing the interrupt itself (or has it blocked!)
Quoted 2 lines
To call this a 2.6.24 regression is a mistake (as I've said before), it's not new to .24 by any means.
Thanks for the explanation, I'm removing this from the regressions list, then.
Greetings,
Rafael
Quoted 7 lines · Rafael J. Wysocki
Subject : jiffies counter leaps in 2.6.24-rc3
Submitter : Stefano Brivio <[email protected]>
Date : 2007-11-29 08:36
References : http://lkml.org/lkml/2007/11/24/53http://bugzilla.kernel.org/show_bug.cgi?id=9475Handled-By Ingo Molnar <[email protected]>
this holds a series of problems, we've applied everything we wanted to 2.6.24 already we'll do the full stack of fixes for this in 2.6.25. (changing printk was deemed inappropriate so late in the -rc cycle) So perhaps mark this as WILL_FIX_LATER and unmark it as a regression? Stefano, do you agree? b43 works fine for you in the latest .24-rc kernel, correct?
Ingo
Quoted 11 lines · Ingo Molnar
Quoted 7 lines · Rafael J. Wysocki
Subject : jiffies counter leaps in 2.6.24-rc3
Submitter : Stefano Brivio <[email protected]>
Date : 2007-11-29 08:36
References : http://lkml.org/lkml/2007/11/24/53http://bugzilla.kernel.org/show_bug.cgi?id=9475Handled-By Ingo Molnar <[email protected]>
Quoted 4 lines
this holds a series of problems, we've applied everything we wanted to 2.6.24 already we'll do the full stack of fixes for this in 2.6.25. (changing printk was deemed inappropriate so late in the -rc cycle) So perhaps mark this as
WILL_FIX_LATERand unmark it as a regression?
I'll be fine with that if Stefano agrees.
Thanks,
Rafael
Quoted 10 lines · On Sun, 6 Jan 2008 10:38:53 +0100 Ingo Molnar <[email protected]> wrote:
Quoted 7 lines · Rafael J. Wysocki
Subject : jiffies counter leaps in 2.6.24-rc3
Submitter : Stefano Brivio <[email protected]>
Date : 2007-11-29 08:36
References : http://lkml.org/lkml/2007/11/24/53http://bugzilla.kernel.org/show_bug.cgi?id=9475Handled-By Ingo Molnar <[email protected]>
Quoted 5 lines
this holds a series of problems, we've applied everything we wanted to 2.6.24 already we'll do the full stack of fixes for this in 2.6.25. (changing printk was deemed inappropriate so late in the -rc cycle) So perhaps mark this as
WILL_FIX_LATERand unmark it as a regression? Stefano, do you agree?
Agreed.
Quoted 1 line
b43 works fine for you in the latest .24-rc kernel, correct?
Correct. :)
--
Ciao
Stefano
Quoted 8 lines · Rafael J. Wysocki
Subject : soft lockup - CPU#1 stuck for 15s! [swapper:0]
Submitter : "Parag Warudkar" <[email protected]>
Date : 2007-12-07 18:14
References : http://lkml.org/lkml/2007/12/7/299http://bugzilla.kernel.org/show_bug.cgi?id=9525Handled-By "Pallipadi, Venkatesh" <[email protected]>Thomas Gleixner <[email protected]> Ingo Molnar <[email protected]>
i think this only occurs with cpuidle, right? drivers/cpuidle/ and CPU_IDLE is new in 2.6.24 so this appears to be a bug in that code (or a bug elsewhere triggered by that code), not a regression from v2.6.23.
this commit might also have improved things:
------------>
commit 2bacec8c318ca0418c0ee9ac662ee44207765dd4
Author: Ingo Molnar <[email protected]>
Date: Tue Dec 18 15:21:13 2007 +0100
sched: touch softlockup watchdog after idling
touch softlockup watchdog after idling.
<------------
albeit Parag reported actual real, human-noticeable delays in system behavior and those cannot be false positives.
Ingo
Quoted 12 lines · Ingo Molnar
Quoted 8 lines · Rafael J. Wysocki
Subject : soft lockup - CPU#1 stuck for 15s! [swapper:0]
Submitter : "Parag Warudkar" <[email protected]>
Date : 2007-12-07 18:14
References : http://lkml.org/lkml/2007/12/7/299http://bugzilla.kernel.org/show_bug.cgi?id=9525Handled-By "Pallipadi, Venkatesh" <[email protected]>Thomas Gleixner <[email protected]> Ingo Molnar <[email protected]>
Quoted 3 lines
i think this only occurs with cpuidle, right?
drivers/cpuidle/andCPU_IDLEis new in 2.6.24 so this appears to be a bug in that code (or a bug elsewhere triggered by that code), not a regression from v2.6.23.
OK, removed from the regressions list.
Thanks,
Rafael
Quoted 13 lines · Rafael J. Wysocki
Quoted 12 lines · Ingo Molnar
Quoted 8 lines · Rafael J. Wysocki
Subject : soft lockup - CPU#1 stuck for 15s! [swapper:0]
Submitter : "Parag Warudkar" <[email protected]>
Date : 2007-12-07 18:14
References : http://lkml.org/lkml/2007/12/7/299http://bugzilla.kernel.org/show_bug.cgi?id=9525Handled-By "Pallipadi, Venkatesh" <[email protected]>Thomas Gleixner <[email protected]> Ingo Molnar <[email protected]>
Quoted 5 lines
Quoted 3 lines
i think this only occurs with cpuidle, right?
drivers/cpuidle/andCPU_IDLEis new in 2.6.24 so this appears to be a bug in that code (or a bug elsewhere triggered by that code), not a regression from v2.6.23.OK, removed from the regressions list.
Nope - actually it did happen without CPU_IDLE so it is definitely a regression. (See http://lkml.org/lkml/2007/12/17/93 )
And it does happen with latest git which I believe has your patch Ingo.
So I would suggest to keep it on the list of regressions.
Thanks
Parag
Quoted 18 lines · Parag Warudkar
Quoted 17 lines · Rafael J. Wysocki
Quoted 15 lines · Ingo Molnar
Quoted 8 lines · Rafael J. Wysocki
Subject : soft lockup - CPU#1 stuck for 15s! [swapper:0]
Submitter : "Parag Warudkar" <[email protected]>
Date : 2007-12-07 18:14
References : http://lkml.org/lkml/2007/12/7/299http://bugzilla.kernel.org/show_bug.cgi?id=9525Handled-By "Pallipadi, Venkatesh" <[email protected]>Thomas Gleixner <[email protected]> Ingo Molnar <[email protected]>
i think this only occurs with cpuidle, right?
drivers/cpuidle/andCPU_IDLEis new in 2.6.24 so this appears to be a bug in that code (or a bug elsewhere triggered by that code), not a regression from v2.6.23.
Quoted 8 lines
Quoted 1 line
OK, removed from the regressions list.
Nope - actually it did happen without
CPU_IDLEso it is definitely a regression. (See http://lkml.org/lkml/2007/12/17/93 )And it does happen with latest git which I believe has your patch Ingo.
So I would suggest to keep it on the list of regressions.
OK
Thanks for the clarification.
Greetings,
Rafael
Quoted 25 lines · Rafael J. Wysocki
Quoted 23 lines · Parag Warudkar
Quoted 13 lines · Rafael J. Wysocki
Quoted 12 lines · Ingo Molnar
Quoted 8 lines · Rafael J. Wysocki
Subject : soft lockup - CPU#1 stuck for 15s! [swapper:0]
Submitter : "Parag Warudkar" <[email protected]>
Date : 2007-12-07 18:14
References : http://lkml.org/lkml/2007/12/7/299http://bugzilla.kernel.org/show_bug.cgi?id=9525Handled-By "Pallipadi, Venkatesh" <[email protected]>Thomas Gleixner <[email protected]> Ingo Molnar <[email protected]>
Quoted 5 lines
Quoted 3 lines
i think this only occurs with cpuidle, right?
drivers/cpuidle/andCPU_IDLEis new in 2.6.24 so this appears to be a bug in that code (or a bug elsewhere triggered by that code), not a regression from v2.6.23.OK, removed from the regressions list.
Nope - actually it did happen without
CPU_IDLEso it is definitely a regression. (See http://lkml.org/lkml/2007/12/17/93 )
Quoted 8 lines
Quoted 3 lines
And it does happen with latest git which I believe has your patch Ingo.
So I would suggest to keep it on the list of regressions.
OK
Thanks for the clarification.
BTW, I have so far tested 2.6.24-rc4/5/6/7 and 2.6.23.12 - all of which have this problem.
Yesterday I went back to using 2.6.22.15 and after a day's uptime it has not reproduced with the same config.
Time for git-bisect I suppose? (the only problem is that this takes anywhere between 20 minutes to 8 hrs to confirm reliably.)
Parag
Quoted 30 lines · Parag Warudkar
Quoted 29 lines · Rafael J. Wysocki
Quoted 26 lines · Parag Warudkar
Quoted 13 lines · Rafael J. Wysocki
Quoted 12 lines · Ingo Molnar
Quoted 8 lines · Rafael J. Wysocki
Subject : soft lockup - CPU#1 stuck for 15s! [swapper:0]
Submitter : "Parag Warudkar" <[email protected]>
Date : 2007-12-07 18:14
References : http://lkml.org/lkml/2007/12/7/299http://bugzilla.kernel.org/show_bug.cgi?id=9525Handled-By "Pallipadi, Venkatesh" <[email protected]>Thomas Gleixner <[email protected]> Ingo Molnar <[email protected]>
Quoted 5 lines
Quoted 3 lines
i think this only occurs with cpuidle, right?
drivers/cpuidle/andCPU_IDLEis new in 2.6.24 so this appears to be a bug in that code (or a bug elsewhere triggered by that code), not a regression from v2.6.23.OK, removed from the regressions list.
Nope - actually it did happen without
CPU_IDLEso it is definitely a regression. (See http://lkml.org/lkml/2007/12/17/93 )And it does happen with latest git which I believe has your patch Ingo.
So I would suggest to keep it on the list of regressions.
Quoted 7 lines
Quoted 4 lines
OK
Thanks for the clarification.
BTW, I have so far tested 2.6.24-rc4/5/6/7 and 2.6.23.12 - all of which have this problem.
Well, now you're saying 2.6.23.12 is also affected, so this doesn't seem to be a recent regression in fact?
Rafael
Quoted 3 lines · Rafael J. Wysocki
Well, now you're saying 2.6.23.12 is also affected, so this doesn't seem to be a recent regression in fact?
I have run 2.6.23 series before but my usage pattern seems to have not triggered the bug before.
But yes, this is a 6 month old regression based on today's findings. (2.6.22 which doesn't have this issue was released on July 8).
Parag
Quoted 10 lines · Parag Warudkar
Quoted 3 lines · Rafael J. Wysocki
Well, now you're saying 2.6.23.12 is also affected, so this doesn't seem to be a recent regression in fact?
I have run 2.6.23 series before but my usage pattern seems to have not triggered the bug before.
But yes, this is a 6 month old regression based on today's findings. (2.6.22 which doesn't have this issue was released on July 8).
Hmm. Can you try plain 2.6.23 ? If it does not show the problem we know that it is caused by one of the patches in the stable series.
Thanks,
tglx