Skip to contentSkip to conversation

CUSTODIANS: List of open issues / not applied patches

U-Boot-Users New Wolfgang Denk 17 participants 24 messages Jan 9, 2008 – Jan 16, 2008 Memory technology devices (MTD)

lore
Share & tools
lore

Wolfgang Denk

author
#0 lore raw

Hello everybody,

this is a heads-up especially for all custodians...

Please review the following list of postings / patches that - to the best of my knowledge - habve not been processed yet; at least I did not mark them as rejected, nor did I find them in the current U-Boot tree.

If possible, please apply and send pull requests ASAP! Thanks.

[It would be helpful to me if you could include my private message ID (the number in column 1) when referring to one of these postings; thanks.]

 9799  09/18 urwithsughosh at gma  Re: [U-Boot-Users] [PATCH]: Reset issue fix on mpc85xx
 9804  09/18 Jason Jin          [PATCH] fsl_pci_init Fix command register initialization issue.
 9952  09/24 Anatolij Gustschi  [U-Boot-Users] [PATCH] Add Fujitsu CoralP/Lime video driver
 9967  09/24 Troy Kisky         Re: [U-Boot-Users] PATCH - Fix oob data copied into supplied buffer
 9969  09/25 Shinya Kuribayash  Re: [U-Boot-Users] [MIPS] Make mips_io_port_base more generic
10068  09/28 Vasiliy Leoenenko  [PATCH] M18 flash (Sibley) support (attempt 2)
10078  09/28 Dan Wilson         [U-Boot-Users] [PATCH] tsec.c patch for receiver reset
10081  09/29 Shinya Kuribayash  [MIPS] Make mips_io_port_base more generic
10159  10/04 Vlad Lungu         [U-Boot-Users] [PATCH] Target support for qemu -M mips
10281  10/10 Vlad Lungu         [PATCH] Fixed pcnet io_base
10282  10/10 Vlad Lungu         [PATCH] Added Am79C970A chip id to pcnet
10397  10/12 Tony Li            [U-Boot-Users] [PATCH] mpc83xx: Add ATM makefile entry for MPC8360EM
10676  10/22 Anton Vorontsov    [U-Boot-Users] [PATCH] MPC8568E-MDS: reset UCCs to use them reliably
10686  10/23 Shinya Kuribayash  Re: [U-Boot-Users] [PATCH 1/1] Fix mips_io_port_base multiple declar
10690  10/22 Anton Vorontsov    [U-Boot-Users] [PATCH] MPC8568E-MDS: set up QE pario for UART1
10810  10/25 Johannes Stezenba  [U-Boot-Users] [patch 0/3] KB9202 CodeSourcery ARM EABI toolchain bu
11193  11/07 llandre            [U-Boot-Users] [PATCH] ARM optimized memcpy/memmove routines
11230  11/09 "Martin Krause"    RE: [U-Boot-Users] [PATCH] TQM5200B: update MTD partition layout
11473  11/19 Matthias Fuchs     Re: [U-Boot-Users] flash hardware protection with CFI driver does no
11522  11/20 stefano babic      [U-Boot-Users] [PATCH] Fix gcc issues in pxa-regs.h
11523  11/20 stefano babic      [U-Boot-Users] [PATCH] MMC for PXA 27X (resubmit)
11635  11/23 sivaji             [U-Boot-Users] MPC8548 problem in Boot Sequencer mode
11911  12/01 Daniel Mack        Re: [U-Boot-Users] [PATCH] add support for Toradex Colibri module
11928  12/03 Yoshihiro Shimoda  [PATCH] serial_sh: Add support for SH7720
11929  12/03 Yoshihiro Shimoda  [PATCH] sh: Add support SH3 and SH7720
11930  12/03 Yoshihiro Shimoda  [PATCH] Add support for MS7720RP02 board
12002  12/06 Ladislav Michl     [U-Boot-Users] [PATCH] ARM: Fix at91rm9200dk base address
12003  12/06 Ladislav Michl     [U-Boot-Users] [PATCH] ARM: AT91RM9200 based boards config cleanup
12007  12/07 Ladislav Michl     [U-Boot-Users] [PATCH] ARM: Board voiceblue update
12044  12/08 Jean-Christophe P  Re: [U-Boot-Users] PATCH: add support for MII-connected ethernet swi
12046  12/08 Jean-Christophe P  Re: [U-Boot-Users] PATCH: ixp42x UART: support 230400bps, enable RTS
12057  12/09 Jean-Christophe P  Re: [U-Boot-Users] PATCH: add support for MII-connected ethernet swi
12096  12/10 Jean-Christophe P  [U-Boot-Users] [PATCH] bf537-stamp: remove already defined is_zero_e
12257  12/13 Jean-Christophe P  [U-Boot-Users] [PATCH] Nios2: remove common/cmd_bdinfo.c unused vari
12382  12/18 Hebbar             Re: [U-Boot-Users] [PATCH] ARM926: compile cpu_init_crit function on
12383  12/18 Hebbar             Re: [U-Boot-Users] [PATCH] ARM926: Remove compiler warning: target C
12384  12/18 Hebbar             Re: [U-Boot-Users] [PATCH] ARM: I2C Init function call in lib_arm/bo
12385  12/18 Hebbar             Re: [U-Boot-Users] [PATCH] ARM926: Display Ethernet info in do_bdinf
12390  12/19 Kumar Gala         [U-Boot-Users] [PATCH] Reworked FSL Book-E TLB macros to be more rea
12392  12/19 Joakim Tjernlund   Re: [U-Boot-Users] 83xx, FSL_UEC reducing boot latency, printf causi
12393  12/19 Stefan Roese       [U-Boot-Users] fdt chosen node handling
12394  12/19 Joakim Tjernlund   Re: [U-Boot-Users] 83xx, FSL_UEC reducing boot latency, printf causi
12395  12/19 "Gururaja Hebbar   Re: [U-Boot-Users] [PATCH] ARM926: compile cpu_init_crit function on
12396  12/19 Dirk Behme         Re: [U-Boot-Users] [PATCH] ARM926: compile cpu_init_crit function on
12404  12/19 Harald Welte       [U-Boot-Users] [PATCH] ARM: arm920/s3c24xx: IRQ demulitplexer callba
12405  12/19 Harald Welte       [U-Boot-Users] [PATCH] ARM: arm920t: Allow use of 'gd' pointer from 
12408  12/19 Harald Welte       [U-Boot-Users] [PATCH] ARM: s3c24xx: Multiple serial port support
12412  12/19 Harald Welte       [U-Boot-Users] [PATCH] ARM: S3C24x0 SoC NAND controller support
12510  12/22 Jean-Christophe P  [U-Boot-Users] [PATCH 1/1] qemu-mips: active HUSH PARSER, AUTO_COMPL
12548  12/25 Anton Vorontsov    [U-Boot-Users] [PATCH] mpc83xx: UEC: add support for Broadcom BCM548
12549  12/25 Anton Vorontsov    [U-Boot-Users] [PATCH] mpc83xx: add support for the MPC8360E-RDK
12602  12/27 Wolfgang Denk      [U-Boot-Users] [PATCH] OMAP5912: fix FIFO handling in UART driver
12818  01/04 Jon Loeliger       [U-Boot-Users] [PATCH] Convert MPC8610HPCD to use libfdt.
12820  01/04 Timur Tabi         Re: [U-Boot-Users] [PATCH] 8610: Fix lingering compile warnings.
12859  01/07 Timur Tabi         [U-Boot-Users] [PATCH v2] 85xx: add ability to upload QE firmware
12866  01/07 Kumar Gala         Re: [U-Boot-Users] [PATCH] MPC85xx KGDB support
12870  01/08 Kumar Gala         [U-Boot-Users] [PATCH] 85xx: Remove cache config from configs.h
12934  01/08 Ben Warren         [U-Boot-Users] [PATCH] Fix Ethernet init() return codes
12938  01/08 Ben Warren         [U-Boot-Users] [PATCH V2] Fix Ethernet init() return codes.

Best regards,

Wolfgang Denk

Signature · 5 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Applying computer technology is simply finding the  right  wrench  to
pound in the correct screw.
#1 lore raw
Quoted 1 line · Wolfgang Denk

12820 01/04 Timur Tabi Re: [U-Boot-Users] [PATCH] 8610: Fix lingering compile warnings.

This is just a comment to a patch from Jon.

Quoted 1 line

12859 01/07 Timur Tabi [U-Boot-Users] [PATCH v2] 85xx: add ability to upload QE firmware

Andy sent a pull request earlier today to pick up this patch.

Signature · 2 lines
Timur Tabi
Linux kernel developer at Freescale
#2 lore raw
In reply to Wolfgang Denk
Quoted 9 lines · Wolfgang Denk

Hello everybody,

this is a heads-up especially for all custodians...

Please review the following list of postings / patches that - to the best of my knowledge - habve not been processed yet; at least I did not mark them as rejected, nor did I find them in the current U-Boot tree.

Quoted 7 lines

If possible, please apply and send pull requests ASAP! Thanks.

[It would be helpful to me if you could include my private message ID (the number in column 1) when referring to one of these postings; thanks.]

12393 12/19 Stefan Roese [U-Boot-Users] fdt chosen node handling

This was discussion email, culminating in my patch "[PATCH] Fine grained per property /chosen updating." which has been applied.
<http://article.gmane.org/gmane.comp.boot-loaders.u-boot/34563/>

Thanks,
gvb

#3 lore raw
In reply to Wolfgang Denk
Quoted 1 line · Wolfgang Denk

9799 09/18 urwithsughosh at gma Re: [U-Boot-Users] [PATCH]: Reset issue fix on mpc85xx

A version of this patch is already committed:
df90968b48fb34fa9072fab150db2ac89678f537

Quoted 3 lines

9804 09/18 Jason Jin [PATCH] fsl_pci_init Fix command register initialization issue.

10078 09/28 Dan Wilson [U-Boot-Users] [PATCH] tsec.c patch for receiver reset

This one was commited: 5c7ea64bb74a850a2b2303f853a8270695ad8602

Quoted 2 lines
10676  10/22 Anton Vorontsov    [U-Boot-Users] [PATCH] MPC8568E-MDS: reset UCCs to use them reliably
10690  10/22 Anton Vorontsov    [U-Boot-Users] [PATCH] MPC8568E-MDS: set up QE pario for UART1

These two are in the current pull request

Quoted 1 line

11635 11/23 sivaji [U-Boot-Users] MPC8548 problem in Boot Sequencer mode

This isn't a patch, but I am tracking the issue. :)

Quoted 1 line

12390 12/19 Kumar Gala [U-Boot-Users] [PATCH] Reworked FSL Book-E TLB macros to be more rea

This is in the current pull request

Quoted 1 line

12859 01/07 Timur Tabi [U-Boot-Users] [PATCH v2] 85xx: add ability to upload QE firmware

In the current pull request

Quoted 1 line

12866 01/07 Kumar Gala Re: [U-Boot-Users] [PATCH] MPC85xx KGDB support

This one has some outstanding issues, so unless I hear something from the author (not Kumar, but I don't have the name in front of me at the moment), it won't go into the next release.

Quoted 1 line

12870 01/08 Kumar Gala [U-Boot-Users] [PATCH] 85xx: Remove cache config from configs.h

In the current pull request

Oh, and sorry about top-posting and over-quoting. I can only guess it was because I was tired. :)

I have rebased my tree, and will send another pull request soon.

Andy

#4 lore raw
In reply to Wolfgang Denk
Quoted 1 line · Wolfgang Denk

11473 11/19 Matthias Fuchs Re: [U-Boot-Users] flash hardware protection with CFI driver does no

This issue did not made it into any patch. We discussed it and ended up with an idea how to add a config option to allow board specific protected flash ranges.

Because I have an open issue on this I will try to provide a patch 'til the end of this week.

Wolfgang, thanks for the reminder.

Matthias

#5 lore raw
In reply to Wolfgang Denk
Quoted 4 lines · On Wed, 09 Jan 2008 22:36:14 +0100 Wolfgang Denk <[email protected]> wrote:

Please review the following list of postings / patches that - to the best of my knowledge - habve not been processed yet; at least I did not mark them as rejected, nor did I find them in the current U-Boot tree.

I can't see this one anywhere:

[PATCH] Conditionally add -fno-stack-protector to CFLAGS
http://groups.google.com.mx/group/osdeve_mirror_boot-loaders_u-boot/browse_thread/thread/c7a0045307cde22

It doesn't matter all that much to me, but I get lots of build errors on powerpc without it. Other arches may be affected too.

Haavard

#6 lore raw
In reply to Wolfgang Denk
Quoted 9 lines · Wolfgang Denk

Hello everybody,

this is a heads-up especially for all custodians...

Please review the following list of postings / patches that - to the best of my knowledge - habve not been processed yet; at least I did not mark them as rejected, nor did I find them in the current U-Boot tree.

Quoted 7 lines

If possible, please apply and send pull requests ASAP! Thanks.

[It would be helpful to me if you could include my private message ID (the number in column 1) when referring to one of these postings; thanks.]

12046 12/08 Jean-Christophe P Re: [U-Boot-Users] PATCH: ixp42x UART: support 230400bps, enable RTS

Replace by IXP: Add full baud-rate support for ixp42x, ixp45x and ixp46x

	and already in the tree as commit 7b74ebe723e576baedf5a8b6240589b19b845a1b
#7 lore raw
In reply to Wolfgang Denk
Quoted 4 lines

If possible, please apply and send pull requests ASAP! Thanks.

12257 12/13 Jean-Christophe P [U-Boot-Users] [PATCH] Nios2: remove common/cmd_bdinfo.c unused vari

Done.

Regards,
--Scott

#8 lore raw
In reply to Wolfgang Denk
Quoted 16 lines · Wolfgang Denk

Hello everybody,

this is a heads-up especially for all custodians...

Please review the following list of postings / patches that - to the best of my knowledge - habve not been processed yet; at least I did not mark them as rejected, nor did I find them in the current U-Boot tree.

If possible, please apply and send pull requests ASAP! Thanks.

[It would be helpful to me if you could include my private message ID (the number in column 1) when referring to one of these postings; thanks.]

<snip>

Quoted 2 lines

10078 09/28 Dan Wilson [U-Boot-Users] [PATCH] tsec.c patch for receiver reset

Looks like Andy already applied this one:
http://article.gmane.org/gmane.comp.boot-loaders.u-boot/32643

Quoted 4 lines

12044 12/08 Jean-Christophe P Re: [U-Boot-Users] PATCH: add support for MII-connected ethernet swi

12057 12/09 Jean-Christophe P Re: [U-Boot-Users] PATCH: add support for MII-connected ethernet swi

These are both responses to a patch submitted by Michael Schwingen. A revised patch was never submitted that I know of.

Quoted 2 lines

12096 12/10 Jean-Christophe P [U-Boot-Users] [PATCH] bf537-stamp: remove already defined is_zero_e

I'll pull this one in.

Quoted 2 lines

12548 12/25 Anton Vorontsov [U-Boot-Users] [PATCH] mpc83xx: UEC: add support for Broadcom BCM548

I've asked Anton for changes to this one

Quoted 3 lines
12934  01/08 Ben Warren         [U-Boot-Users] [PATCH] Fix Ethernet init() return codes
12938  01/08 Ben Warren         [U-Boot-Users] [PATCH V2] Fix Ethernet init() return codes.

You've pulled this in. Sorry for being Captain Obvious.

regards,
Ben

#9 lore raw
In reply to Wolfgang Denk
Quoted 1 line · On Wed, 09 Jan 2008 22:36:14 +0100 Wolfgang Denk <[email protected]> wrote:

10397 10/12 Tony Li [U-Boot-Users] [PATCH] mpc83xx: Add ATM makefile entry for MPC8360EM

this is already in your mainline tree (commit
281df457c1aa50d2752165d0c5c3282d4027b974).

Quoted 1 line

12392 12/19 Joakim Tjernlund Re: [U-Boot-Users] 83xx, FSL_UEC reducing boot latency, printf causi

this was never intended to be a final patch; we're still working out the issues.

Quoted 1 line

12394 12/19 Joakim Tjernlund Re: [U-Boot-Users] 83xx, FSL_UEC reducing boot latency, printf causi

same as above. I'll try and get back to it before the Jan. 17 deadline.

Quoted 1 line

12548 12/25 Anton Vorontsov [U-Boot-Users] [PATCH] mpc83xx: UEC: add support for Broadcom BCM548

Ben Warren is handling the newer version of this one (and it looks like Anton will resubmit it again).

Quoted 1 line

12549 12/25 Anton Vorontsov [U-Boot-Users] [PATCH] mpc83xx: add support for the MPC8360E-RDK

I'm about to ask you to pull the newer version of this.

so, assuming you pull on my next request, the above can be removed from your list.

Kim

#10 lore raw
In reply to Wolfgang Denk

u-boot-users-bounces at lists.sourceforge.net wrote on :

Quoted 9 lines

Hello everybody,

this is a heads-up especially for all custodians...

Please review the following list of postings / patches that - to the best of my knowledge - habve not been processed yet; at least I did not mark them as rejected, nor did I find them in the current U-Boot tree.

Quoted 8 lines

If possible, please apply and send pull requests ASAP! Thanks.

[It would be helpful to me if you could include my private message ID (the number in column 1) when referring to one of these postings; thanks.]

11230 11/09 "Martin Krause" RE: [U-Boot-Users] [PATCH] TQM5200B: update
MTD partition layout

After the first version of the patch was NAKed, I reveived no (positiv) answer to my then proposed alternative flash layout and the offer to submit a new patch. So I assumed the patch will also not be accepted and did no further work on this.

Best regards,
Martin Krause

#11 lore raw
In reply to Wolfgang Denk

(resend due to mailserver problems)

Quoted 8 lines · Wolfgang Denk

Hello everybody,

this is a heads-up especially for all custodians...

Please review the following list of postings / patches that - to the best of my knowledge - habve not been processed yet; at least I did not mark them as rejected, nor did I find them in the current U-Boot tree.

Not sure about the source of the problem, but the CONFIG_CFI_FLASH_LEGACY support seems to be broken - the code for flash_read_jedec_ids_intel and flash_read_jedec_ids_amd which are called in cfi_flash.c seems to be missing. I do not see any missing/outstanding patches that seem relevant to this problem.

Am I looking at the wrong branch?

cu
Michael

#12 lore raw

Hi Michael,

Quoted 7 lines · Michael Schwingen
Quoted 6 lines

this is a heads-up especially for all custodians...

Please review the following list of postings / patches that - to the best of my knowledge - habve not been processed yet; at least I did not mark them as rejected, nor did I find them in the current U-Boot tree.

Quoted 7 lines

Not sure about the source of the problem, but the CONFIG_CFI_FLASH_LEGACY support seems to be broken - the code for flash_read_jedec_ids_intel and flash_read_jedec_ids_amd which are called in cfi_flash.c seems to be missing. I do not see any missing/outstanding patches that seem relevant to this problem.

Am I looking at the wrong branch?

No. You CFI/JEDEC rework should be available in the official repository right now. Could be that something slipped though. Best would be if you would provide a patch that adds the missing JEDEC stuff.

Thanks.

Best regards,
Stefan

=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================

#13 lore raw

PATCH 1/1 fix CONFIG_FLASH_CFI_LEGACY compilation

Quoted 4 lines · Stefan Roese

No. You CFI/JEDEC rework should be available in the official repository right now. Could be that something slipped though. Best would be if you would provide a patch that adds the missing JEDEC stuff.

Okay - after a closer look, just a small change is required.

Signed-off-by Michael Schwingen <[email protected]>
drivers/mtd/cfi_flash.c +2 -2
index 4f61e36..3a3439c 100644
@@ -1446,11 +1446,11 @@ static void flash_read_jedec_ids (flash_info_t * info)
 	switch (info->vendor) {
 	case CFI_CMDSET_INTEL_STANDARD:
 	case CFI_CMDSET_INTEL_EXTENDED:
-		flash_read_jedec_ids_intel(info);
+		cmdset_amd_read_jedec_ids(info);
 		break;
 	case CFI_CMDSET_AMD_STANDARD:
 	case CFI_CMDSET_AMD_EXTENDED:
-		flash_read_jedec_ids_amd(info);
+		cmdset_intel_read_jedec_ids(info);
 		break;
 	default:
 		break;
author
#14 lore raw

PATCH 1/1 fix CONFIG_FLASH_CFI_LEGACY compilation

Quoted 7 lines · In message <[email protected]> you wrote:
Quoted 4 lines · Stefan Roese

No. You CFI/JEDEC rework should be available in the official repository right now. Could be that something slipped though. Best would be if you would provide a patch that adds the missing JEDEC stuff.

Okay - after a closer look, just a small change is required.

Hm... either you got the patch inverse, or something is seriously broken:

drivers/mtd/cfi_flash.c static void flash_read_jedec_ids (flash_info_t * info) · line 1450

Quoted 5 lines
drivers/mtd/cfi_flash.c +1 -1
 	case CFI_CMDSET_INTEL_STANDARD:
 	case CFI_CMDSET_INTEL_EXTENDED:
-		flash_read_jedec_ids_intel(info);
+		cmdset_amd_read_jedec_ids(info);
 		break;

For INTEL flashes use the AMD command set, and ...

drivers/mtd/cfi_flash.c static void flash_read_jedec_ids (flash_info_t * info) · line 1453

Quoted 4 lines
drivers/mtd/cfi_flash.c +1 -1
 	case CFI_CMDSET_AMD_STANDARD:
 	case CFI_CMDSET_AMD_EXTENDED:
-		flash_read_jedec_ids_amd(info);
+		cmdset_intel_read_jedec_ids(info);

...for AMD flashes use the INTEL command set?

This makes no sense to me.

Best regards,

Wolfgang Denk

Signature · 4 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
"If anything can go wrong, it will."                   - Edsel Murphy
#15 lore raw

PATCH 1/1 fix CONFIG_FLASH_CFI_LEGACY compilation

Quoted 2 lines · Wolfgang Denk

Hm... either you got the patch inverse, or something is seriously broken:

I vote for the second option - don't know what got into me. The strange thing is that it worked, nevertheless ...

cu
Michael

Signed-off-by Michael Schwingen <[email protected]>
drivers/mtd/cfi_flash.c +2 -2
index 4f61e36..eb509f5 100644
@@ -1446,11 +1446,11 @@ static void flash_read_jedec_ids (flash_info_t * info)
 	switch (info->vendor) {
 	case CFI_CMDSET_INTEL_STANDARD:
 	case CFI_CMDSET_INTEL_EXTENDED:
-		flash_read_jedec_ids_intel(info);
+		cmdset_intel_read_jedec_ids(info);
 		break;
 	case CFI_CMDSET_AMD_STANDARD:
 	case CFI_CMDSET_AMD_EXTENDED:
-		flash_read_jedec_ids_amd(info);
+		cmdset_amd_read_jedec_ids(info);
 		break;
 	default:
 		break;
#16 lore raw

PATCH 1/1 fix CONFIG_FLASH_CFI_LEGACY compilation

Quoted 11 lines · Michael Schwingen
Quoted 2 lines · Wolfgang Denk

Hm... either you got the patch inverse, or something is seriously broken:

I vote for the second option - don't know what got into me. The strange thing is that it worked, nevertheless ...

cu
Michael

Signed-off-by Michael Schwingen <[email protected]>

Thanks. Applied to cfi-flash repository.

Pull request will follow soon.

Best regards,
Stefan

=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================

#17 lore raw
In reply to Michael Schwingen
Quoted 5 lines · On Fri, 11 Jan 2008 22:06:30 +0100 rincewind at discworld.dascon.de (Michael…

Not sure about the source of the problem, but the CONFIG_CFI_FLASH_LEGACY support seems to be broken - the code for flash_read_jedec_ids_intel and flash_read_jedec_ids_amd which are called in cfi_flash.c seems to be missing. I do not see any missing/outstanding patches that seem relevant to this problem.

Hmm...I guess my compile tests didn't hit the CONFIG_CFI_FLASH_LEGACY case. Are there any boards that are actually using this in mainline?

Thanks for fixing it.

Haavard

#18 lore raw
Quoted 3 lines · Haavard Skinnemoen

Hmm...I guess my compile tests didn't hit the CONFIG_CFI_FLASH_LEGACY case. Are there any boards that are actually using this in mainline?

Not yet. AcTux-4 will be, as soon as it is fit for inclusion.

cu
Michael

#19 lore raw
In reply to Wolfgang Denk

Hi,

Quoted 3 lines · Wolfgang Denk
 9969  09/25 Shinya Kuribayash  Re: [U-Boot-Users] [MIPS] Make mips_io_port_base more generic
10081  09/29 Shinya Kuribayash  [MIPS] Make mips_io_port_base more generic
10686  10/23 Shinya Kuribayash  Re: [U-Boot-Users] [PATCH 1/1] Fix mips_io_port_base multiple declar

these are already in v1.3.0. Please drop them from your list.

Quoted 2 lines
10159  10/04 Vlad Lungu         [U-Boot-Users] [PATCH] Target support for qemu -M mips
12510  12/22 Jean-Christophe P  [U-Boot-Users] [PATCH 1/1] qemu-mips: active HUSH PARSER, AUTO_COMPL

I don't feel no need to be in a rush to these stuffs. And they needs some possible cleanups, a MAINTAINER file entry, and so on. With these changes, I'll pull request in the future.

Shinya

#20 lore raw
Quoted 9 lines · Shinya Kuribayashi
Quoted 4 lines
  
10159  10/04 Vlad Lungu         [U-Boot-Users] [PATCH] Target support for qemu -M mips
12510  12/22 Jean-Christophe P  [U-Boot-Users] [PATCH 1/1] qemu-mips: active HUSH PARSER, AUTO_COMPL

I don't feel no need to be in a rush to these stuffs. And they needs some possible cleanups, a MAINTAINER file entry, and so on. With these changes, I'll pull request in the future.

Just saw your comments on JC's patch. Last message in:

http://www.nabble.com/Target-support-for-qemu--M-mips-td14375017.html

Can you please be more specific about the issues you have with my patch? I haven't seen any negative feedback (or much positive feedback :-] ) on the list or in private e-mail. I'm open to suggestions, as long as I get any ;-)

As for pushing into mainline, I don't want to rush this, but I have sent and re-sent this since end of September. If the next merge window opens in the summer,
I'll just give up.

Vlad

#21 lore raw
Quoted 8 lines · Vlad Lungu

Just saw your comments on JC's patch. Last message in:

http://www.nabble.com/Target-support-for-qemu--M-mips-td14375017.html

Can you please be more specific about the issues you have with my patch? I haven't seen any negative feedback (or much positive feedback :-] ) on the list or in private e-mail. I'm open to suggestions, as long as I get any ;-)

Ok, I'll review the patch. Wait a while.

Quoted 4 lines

As for pushing into mainline, I don't want to rush this, but I have sent and re-sent this since end of September. If the next merge window opens in the summer,
I'll just give up.

So I have to push this now :-)

Shinya

#22 lore raw
Quoted 5 lines · Shinya Kuribayashi
Quoted 4 lines · Vlad Lungu

Just saw your comments on JC's patch. Last message in:

http://www.nabble.com/Target-support-for-qemu--M-mips-td14375017.html

Quoted 8 lines
Quoted 5 lines

Can you please be more specific about the issues you have with my patch? I haven't seen any negative feedback (or much positive feedback :-] )
on the list or in private e-mail. I'm open to suggestions, as long as I get any ;-)

Ok, I'll review the patch. Wait a while.

OK.

Quoted 6 lines
Quoted 4 lines

As for pushing into mainline, I don't want to rush this, but I have sent and re-sent this since end of September. If the next merge window opens in the summer,
I'll just give up.

So I have to push this now :-)

You don't HAVE to, but it would be nice to consider it.

Vlad

#23 lore raw
In reply to Wolfgang Denk
Quoted 3 lines · On Wed, 09 Jan 2008 22:36:14 +0100 Wolfgang Denk <[email protected]> wrote:
11928  12/03 Yoshihiro Shimoda  [PATCH] serial_sh: Add support for SH7720
11929  12/03 Yoshihiro Shimoda  [PATCH] sh: Add support SH3 and SH7720
11930  12/03 Yoshihiro Shimoda  [PATCH] Add support for MS7720RP02 board

I picked up and apply these patches.
These patches are included in next request-pull.

regards,
Nobuhiro

Signature · 2 lines
Nobuhiro Iwamatsu
	GPG ID : 3170EBE9