Skip to contentSkip to conversation

MPC8360E-RDK: device tree, board file and defconfig

PATCH In review Anton Vorontsov 2 participants 4 messages Feb 1, 2008 – Feb 11, 2008

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH v4 1/1 MPC8360E-RDK: device tree, board file and defconfig

This is new board made by Freescale Semiconductor Inc. and Logic Product Development.

Currently supported:
1. UEC{1,2,7,4};
2. I2C;
3. SPI;
4. NS16550 serial;
5. PCI and miniPCI;
6. Intel NOR StrataFlash X16 64Mbit PC28F640P30T85;
7. Graphics controller, Fujitsu MB86277.

Not supported so far:
1. StMICRO NAND512W3A2BN6E, 512 Mbit (supported with FSL UPM patches);
2. QE Serial UCCs (tested to not work with ucc_uart driver, reason unknown, yet);
3. ADC AD7843 (tested to work, but support via device tree depends on major SPI rework, GPIO API, etc);
4. FHCI USB (will send RFC patches soon).

---

Hello Kumar,

It would be great if we can get this into the 2.6.25.

Changes since v3:
- rebased against recent tree;
- compatible = "fsl,mpc8360-immr", "fsl,immr", "simple-bus";
- now "qe" node is the child of the "soc" node;
- proper #{address,size}-cells for the muram node;
- unused par_io node removed (in favour of upcoming GPIO support).

Thanks,

 arch/powerpc/boot/dts/mpc836x_rdk.dts      |  368 ++++++++++
 arch/powerpc/configs/mpc836x_rdk_defconfig | 1053 ++++++++++++++++++++++++++++
 arch/powerpc/platforms/83xx/Kconfig        |    8 +
 arch/powerpc/platforms/83xx/Makefile       |    1 +
 arch/powerpc/platforms/83xx/mpc836x_rdk.c  |  105 +++
 5 files changed, 1535 insertions(+), 0 deletions(-)
 create mode 100644 arch/powerpc/boot/dts/mpc836x_rdk.dts
 create mode 100644 arch/powerpc/configs/mpc836x_rdk_defconfig
 create mode 100644 arch/powerpc/platforms/83xx/mpc836x_rdk.c
arch/powerpc/boot/dts/mpc836x_rdk.dts new file +368 -0
new file mode 100644
index 0000000..b062f9b
@@ -0,0 +1,368 @@
+/*
+ * MPC8360E RDK Device Tree Source
+ *
+ * Copyright 2006 Freescale Semiconductor Inc.
+ * Copyright 2007 MontaVista Software, Inc.
+ * 		  Anton Vorontsov <[email protected]>
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+/dts-v1/;
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "fsl,mpc8360erdk";
+
+	aliases {
+		serial0 = &serial0;
+		serial1 = &serial1;
+		serial2 = &serial2;
+		serial3 = &serial3;
+		ethernet0 = &enet0;
+		ethernet1 = &enet1;
+		ethernet2 = &enet2;
+		ethernet3 = &enet3;
+		pci0 = &pci0;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		PowerPC,8360@0 {
+			device_type = "cpu";
+			reg = <0>;
+			d-cache-line-size = <32>;
+			i-cache-line-size = <32>;
+			d-cache-size = <32768>;
+			i-cache-size = <32768>;
+			/* filled by u-boot */
+			timebase-frequency = <0>;
+			bus-frequency = <0>;
+			clock-frequency = <0>;
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		/* filled by u-boot */
+		reg = <0 0>;
+	};
+
+	soc@e0000000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		device_type = "soc";
+		compatible = "fsl,mpc8360-immr", "fsl,immr", "simple-bus";
+		ranges = <0 0xe0000000 0x200000>;
+		reg = <0xe0000000 0x200>;
+		/* filled by u-boot */
+		bus-frequency = <0>;
+
+		wdt@200 {
+			compatible = "mpc83xx_wdt";
+			reg = <0x200 0x100>;
+		};
+
+		i2c@3000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			cell-index = <0>;
+			compatible = "fsl-i2c";
+			reg = <0x3000 0x100>;
+			interrupts = <14 8>;
+			interrupt-parent = <&ipic>;
+			dfsrr;
+		};
+
+		i2c@3100 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			cell-index = <1>;
+			compatible = "fsl-i2c";
+			reg = <0x3100 0x100>;
+			interrupts = <16 8>;
+			interrupt-parent = <&ipic>;
+			dfsrr;
+		};
+
+		serial0: serial@4500 {
+			device_type = "serial";
+			compatible = "ns16550";
+			reg = <0x4500 0x100>;
+			interrupts = <9 8>;
+			interrupt-parent = <&ipic>;
+			/* filled by u-boot */
+			clock-frequency = <0>;
+		};
+
+		serial1: serial@4600 {
+			device_type = "serial";
+			compatible = "ns16550";
+			reg = <0x4600 0x100>;
+			interrupts = <10 8>;
+			interrupt-parent = <&ipic>;
+			/* filled by u-boot */
+			clock-frequency = <0>;
+		};
+
+		crypto@30000 {
+			compatible = "fsl,sec2-crypto";
+			reg = <0x30000 0x10000>;
+			interrupts = <11 8>;
+			interrupt-parent = <&ipic>;
+			num-channels = <4>;
+			channel-fifo-len = <24>;
+			exec-units-mask = <0x7e>;
+			/*
+			 * desc mask is for rev1.x, we need runtime fixup
+			 * for >=2.x
+			 */
+			descriptor-types-mask = <0x1010ebf>;
+		};
+
+		ipic: interrupt-controller@700 {
+			#address-cells = <0>;
+			#interrupt-cells = <2>;
+			compatible = "fsl,pq2pro-pic", "fsl,ipic";
+			interrupt-controller;
+			reg = <0x700 0x100>;
+		};
+
+		qe@100000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			device_type = "qe";
+			compatible = "fsl,qe", "simple-bus";
+			ranges = <0 0x100000 0x100000>;
+			reg = <0x100000 0x480>;
+			/* filled by u-boot */
+			clock-frequency = <0>;
+			bus-frequency = <0>;
+			brg-frequency = <0>;
+
+			muram@10000 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				compatible = "fsl,qe-muram", "fsl,cpm-muram";
+				ranges = <0 0x10000 0xc000>;
+
+				data-only@0 {
+					compatible = "fsl,qe-muram-data",
+						     "fsl,cpm-muram-data";
+					reg = <0 0xc000>;
+				};
+			};
+
+			spi@4c0 {
+				cell-index = <0>;
+				compatible = "fsl,spi";
+				reg = <0x4c0 0x40>;
+				interrupts = <2>;
+				interrupt-parent = <&qeic>;
+				mode = "cpu-qe";
+			};
+
+			spi@500 {
+				cell-index = <1>;
+				compatible = "fsl,spi";
+				reg = <0x500 0x40>;
+				interrupts = <1>;
+				interrupt-parent = <&qeic>;
+				mode = "cpu-qe";
+			};
+
+			enet0: ucc@2000 {
+				device_type = "network";
+				compatible = "ucc_geth";
+				device-id = <1>;
+				reg = <0x2000 0x200>;
+				interrupts = <32>;
+				interrupt-parent = <&qeic>;
+				rx-clock-name = "none";
+				tx-clock-name = "clk9";
+				phy-handle = <&phy2>;
+				phy-connection-type = "rgmii-id";
+				/* filled by u-boot */
+				local-mac-address = [ 00 00 00 00 00 00 ];
+			};
+
+			enet1: ucc@3000 {
+				device_type = "network";
+				compatible = "ucc_geth";
+				device-id = <2>;
+				reg = <0x3000 0x200>;
+				interrupts = <33>;
+				interrupt-parent = <&qeic>;
+				rx-clock-name = "none";
+				tx-clock-name = "clk4";
+				phy-handle = <&phy4>;
+				phy-connection-type = "rgmii-id";
+				/* filled by u-boot */
+				local-mac-address = [ 00 00 00 00 00 00 ];
+			};
+
+			enet2: ucc@2600 {
+				device_type = "network";
+				compatible = "ucc_geth";
+				device-id = <7>;
+				reg = <0x2600 0x200>;
+				interrupts = <42>;
+				interrupt-parent = <&qeic>;
+				rx-clock-name = "clk20";
+				tx-clock-name = "clk19";
+				phy-handle = <&phy1>;
+				phy-connection-type = "mii";
+				/* filled by u-boot */
+				local-mac-address = [ 00 00 00 00 00 00 ];
+			};
+
+			enet3: ucc@3200 {
+				device_type = "network";
+				compatible = "ucc_geth";
+				device-id = <4>;
+				reg = <0x3200 0x200>;
+				interrupts = <35>;
+				interrupt-parent = <&qeic>;
+				rx-clock-name = "clk8";
+				tx-clock-name = "clk7";
+				phy-handle = <&phy3>;
+				phy-connection-type = "mii";
+				/* filled by u-boot */
+				local-mac-address = [ 00 00 00 00 00 00 ];
+			};
+
+			mdio@2120 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "fsl,ucc-mdio";
+				reg = <0x2120 0x18>;
+
+				phy1: ethernet-phy@1 {
+					device_type = "ethernet-phy";
+					compatible = "national,DP83848VV";
+					reg = <1>;
+				};
+
+				phy2: ethernet-phy@2 {
+					device_type = "ethernet-phy";
+					compatible = "broadcom,BCM5481UA2KMLG";
+					reg = <2>;
+				};
+
+				phy3: ethernet-phy@3 {
+					device_type = "ethernet-phy";
+					compatible = "national,DP83848VV";
+					reg = <3>;
+				};
+
+				phy4: ethernet-phy@4 {
+					device_type = "ethernet-phy";
+					compatible = "broadcom,BCM5481UA2KMLG";
+					reg = <4>;
+				};
+			};
+
+			serial2: ucc@2400 {
+				device_type = "serial";
+				compatible = "ucc_uart";
+				reg = <0x2400 0x200>;
+				device-id = <5>;
+				port-number = <0>;
+				rx-clock-name = "brg7";
+				tx-clock-name = "brg8";
+				interrupts = <40>;
+				interrupt-parent = <&qeic>;
+				soft-uart;
+			};
+
+			serial3: ucc@3400 {
+				device_type = "serial";
+				compatible = "ucc_uart";
+				reg = <0x3400 0x200>;
+				device-id = <6>;
+				port-number = <1>;
+				rx-clock-name = "brg13";
+				tx-clock-name = "brg14";
+				interrupts = <41>;
+				interrupt-parent = <&qeic>;
+				soft-uart;
+			};
+
+			qeic: interrupt-controller@80 {
+				#address-cells = <0>;
+				#interrupt-cells = <1>;
+				compatible = "fsl,qe-ic";
+				interrupt-controller;
+				reg = <0x80 0x80>;
+				big-endian;
+				interrupts = <32 8 33 8>;
+				interrupt-parent = <&ipic>;
+			};
+		};
+	};
+
+	localbus@e0005000 {
+		#address-cells = <2>;
+		#size-cells = <1>;
+		compatible = "fsl,mpc8360-localbus", "fsl,pq2pro-localbus",
+			     "simple-bus";
+		reg = <0xe0005000 0xd8>;
+		ranges = <0 0 0xff800000 0x0800000
+			  2 0 0x70000000 0x4000000>;
+
+		nor-flash@0,0 {
+			compatible = "intel,PC28F640P30T85", "cfi-flash";
+			reg = <0 0 0x800000>;
+			bank-width = <2>;
+			device-width = <1>;
+		};
+
+		display@2,0 {
+			device_type = "display";
+			compatible = "fujitsu,MB86277", "fujitsu,mint";
+			reg = <2 0 0x4000000>;
+			fujitsu,sh3;
+			little-endian;
+			/* filled by u-boot */
+			address = <0>;
+			depth = <0>;
+			width = <0>;
+			height = <0>;
+			linebytes = <0>;
+			/* linux,opened; - added by uboot */
+		};
+	};
+
+	pci0: pci@e0008500 {
+		#address-cells = <3>;
+		#size-cells = <2>;
+		#interrupt-cells = <1>;
+		device_type = "pci";
+		compatible = "fsl,mpc8360-pci", "fsl,mpc8349-pci";
+		reg = <0xe0008500 0x100>;
+		ranges = <0x02000000 0 0x90000000 0x90000000 0 0x10000000
+			  0x42000000 0 0x80000000 0x80000000 0 0x10000000
+			  0x01000000 0 0xe0300000 0xe0300000 0 0x00100000>;
+		interrupts = <66 8>;
+		interrupt-parent = <&ipic>;
+		interrupt-map-mask = <0xf800 0 0 7>;
+		interrupt-map = </* miniPCI0 IDSEL 0x14 AD20 */
+				 0xa000 0 0 1 &ipic 18 8
+				 0xa000 0 0 2 &ipic 19 8
+
+				 /* PCI1 IDSEL 0x15 AD21 */
+				 0xa800 0 0 1 &ipic 19 8
+				 0xa800 0 0 2 &ipic 20 8
+				 0xa800 0 0 3 &ipic 21 8
+				 0xa800 0 0 4 &ipic 18 8>;
+		/* filled by u-boot */
+		bus-range = <0 0>;
+		clock-frequency = <0>;
+	};
+};
arch/powerpc/configs/mpc836x_rdk_defconfig new file +1053 -0

1,053 lines not on this page · raw message

arch/powerpc/platforms/83xx/Kconfig +8 -0
index 13587e2..a5f72bb 100644
@@ -58,6 +58,14 @@ config MPC836x_MDS
 	help
 	  This option enables support for the MPC836x MDS Processor Board.
 
+config MPC836x_RDK
+	bool "Freescale/Logic MPC836x RDK"
+	select DEFAULT_UIMAGE
+	select QUICC_ENGINE
+	help
+	  This option enables support for the MPC836x RDK Processor Board,
+	  also known as ZOOM PowerQUICC Kit.
+
 config MPC837x_MDS
 	bool "Freescale MPC837x MDS"
 	select DEFAULT_UIMAGE
arch/powerpc/platforms/83xx/Makefile +1 -0
index 7e6dd3e..1fcda8e 100644
@@ -8,6 +8,7 @@ obj-$(CONFIG_MPC832x_RDB)	+= mpc832x_rdb.o
 obj-$(CONFIG_MPC834x_MDS)	+= mpc834x_mds.o
 obj-$(CONFIG_MPC834x_ITX)	+= mpc834x_itx.o
 obj-$(CONFIG_MPC836x_MDS)	+= mpc836x_mds.o
+obj-$(CONFIG_MPC836x_RDK)	+= mpc836x_rdk.o
 obj-$(CONFIG_MPC832x_MDS)	+= mpc832x_mds.o
 obj-$(CONFIG_MPC837x_MDS)	+= mpc837x_mds.o
 obj-$(CONFIG_SBC834x)		+= sbc834x.o
arch/powerpc/platforms/83xx/mpc836x_rdk.c new file +105 -0

105 lines not on this page · raw message

Signature · 1 line
1.5.2.2
#1 lore raw
Quoted 20 lines · Anton Vorontsov

This is new board made by Freescale Semiconductor Inc. and Logic Product Development.

Currently supported:
1. UEC{1,2,7,4};
2. I2C;
3. SPI;
4. NS16550 serial;
5. PCI and miniPCI;
6. Intel NOR StrataFlash X16 64Mbit PC28F640P30T85;
7. Graphics controller, Fujitsu MB86277.

Not supported so far:
1. StMICRO NAND512W3A2BN6E, 512 Mbit (supported with FSL UPM patches);
2. QE Serial UCCs (tested to not work with ucc_uart driver, reason unknown, yet);
3. ADC AD7843 (tested to work, but support via device tree depends on major SPI rework, GPIO API, etc);
4. FHCI USB (will send RFC patches soon).

Quoted 6 lines

---

Hello Kumar,

It would be great if we can get this into the 2.6.25.

Is there any chance this will hit 2.6.25?..

Thanks,

Signature · 4 lines
Anton Vorontsov
email: [email protected]
backup email: [email protected]
irc://irc.freenode.net/bd2
#2 lore raw
Quoted 21 lines · Anton Vorontsov
Quoted 20 lines · Anton Vorontsov

This is new board made by Freescale Semiconductor Inc. and Logic Product Development.

Currently supported:
1. UEC{1,2,7,4};
2. I2C;
3. SPI;
4. NS16550 serial;
5. PCI and miniPCI;
6. Intel NOR StrataFlash X16 64Mbit PC28F640P30T85;
7. Graphics controller, Fujitsu MB86277.

Not supported so far:
1. StMICRO NAND512W3A2BN6E, 512 Mbit (supported with FSL UPM patches);
2. QE Serial UCCs (tested to not work with ucc_uart driver, reason unknown, yet);
3. ADC AD7843 (tested to work, but support via device tree depends on major SPI rework, GPIO API, etc);
4. FHCI USB (will send RFC patches soon).

Quoted 8 lines
Quoted 6 lines

---

Hello Kumar,

It would be great if we can get this into the 2.6.25.

Is there any chance this will hit 2.6.25?..

Not really. It seemed like there were a lot of other patches this really depend on getting so I was waiting to see how that fell out. As Linus, just released 2.6.25-rc1 lets queue this up for 2.6.26.

- k

#3 lore raw
Quoted 28 lines · Kumar Gala
Quoted 25 lines · Anton Vorontsov
Quoted 24 lines · Anton Vorontsov

This is new board made by Freescale Semiconductor Inc. and Logic Product Development.

Currently supported:
1. UEC{1,2,7,4};
2. I2C;
3. SPI;
4. NS16550 serial;
5. PCI and miniPCI;
6. Intel NOR StrataFlash X16 64Mbit PC28F640P30T85;
7. Graphics controller, Fujitsu MB86277.

Not supported so far:
1. StMICRO NAND512W3A2BN6E, 512 Mbit (supported with FSL UPM patches);
2. QE Serial UCCs (tested to not work with ucc_uart driver, reason unknown, yet);
3. ADC AD7843 (tested to work, but support via device tree depends on major SPI rework, GPIO API, etc);
4. FHCI USB (will send RFC patches soon).

---

Quoted 8 lines
Quoted 5 lines
Quoted 3 lines

Hello Kumar,

It would be great if we can get this into the 2.6.25.

Is there any chance this will hit 2.6.25?..

Not really. It seemed like there were a lot of other patches this really depend on getting so I was waiting to see how that fell out.

Hm... This particular patch doesn't depend on any other patches.

This is "basic support" patch with intent to be in time for .25.

NAND/ADC/FHCI support is .26 material, of course, and that's exactly why "basic support" patch doesn't include these bits.

Signature · 4 lines
Anton Vorontsov
email: [email protected]
backup email: [email protected]
irc://irc.freenode.net/bd2