Skip to contentSkip to conversation

x86: validate against acpi motherboard resources

PATCH In review Yinghai Lu 2 participants 8 messages Feb 12, 2008

Subsystems (3)
lore
Share & tools
lore

Yinghai Lu

author
#0 lore raw

PATCH 1/4 x86: validate against acpi motherboard resources

From: Robert Hancock <[email protected]>

This path adds validation of the MMCONFIG table against the ACPI reserved motherboard resources. If the MMCONFIG table is found to be reserved in ACPI, we don't bother checking the E820 table. The PCI Express firmware spec apparently tells BIOS developers that reservation in ACPI is required and E820 reservation is optional, so checking against ACPI first makes sense. Many BIOSes don't reserve the MMCONFIG region in E820 even though it is perfectly functional, the existing check needlessly disables MMCONFIG in these cases.

In order to do this, MMCONFIG setup has been split into two phases. If PCI configuration type 1 is not available then MMCONFIG is enabled early as before. Otherwise, it is enabled later after the ACPI interpreter is enabled, since we need to be able to execute control methods in order to check the ACPI reserved resources. Presently this is just triggered off the end of ACPI interpreter initialization.

There are a few other behavioral changes here:

- Validate all MMCONFIG configurations provided, not just the first one.

- Validate the entire required length of each configuration according to the provided ending bus number is reserved, not just the minimum required allocation.

- Validate that the area is reserved even if we read it from the chipset directly and not from the MCFG table. This catches the case where the BIOS didn't set the location properly in the chipset and has mapped it over other things it shouldn't have.

This also cleans up the MMCONFIG initialization functions so that they simply do nothing if MMCONFIG is not compiled in.

Based on an original patch by Rajesh Shah from Intel.

---

 arch/x86/pci/init.c            |    4 
 arch/x86/pci/mmconfig-shared.c |  151 +++++++++++++++++++++++++++----
 arch/x86/pci/pci.h             |    1 
 drivers/acpi/bus.c             |    2 
 include/linux/pci.h            |    8 +
 5 files changed, 144 insertions(+), 22 deletions(-)
arch/x86/pci/init.c +1 -3
Index: linux-2.6/arch/x86/pci/init.c
===================================================================
@@ -11,9 +11,7 @@ static __init int pci_access_init(void)
 #ifdef CONFIG_PCI_DIRECT
 	type = pci_direct_probe();
 #endif
-#ifdef CONFIG_PCI_MMCONFIG
-	pci_mmcfg_init(type);
-#endif
+	pci_mmcfg_early_init(type);
 	if (raw_pci_ops)
 		return 0;
 #ifdef CONFIG_PCI_BIOS
arch/x86/pci/mmconfig-shared.c +132 -17

178 lines not on this page · raw message

arch/x86/pci/pci.h +0 -1
Index: linux-2.6/arch/x86/pci/pci.h
===================================================================
@@ -100,7 +100,6 @@ extern struct pci_raw_ops pci_direct_con
 extern int pci_direct_probe(void);
 extern void pci_direct_init(int type);
 extern void pci_pcbios_init(void);
-extern void pci_mmcfg_init(int type);
 extern void pcibios_sort(void);
 
 /* pci-mmconfig.c */
drivers/acpi/bus.c +2 -0
Index: linux-2.6/drivers/acpi/bus.c
===================================================================
@@ -35,6 +35,7 @@
 #ifdef CONFIG_X86
 #include <asm/mpspec.h>
 #endif
+#include <linux/pci.h>
 #include <acpi/acpi_bus.h>
 #include <acpi/acpi_drivers.h>
 
@@ -783,6 +784,7 @@ static int __init acpi_init(void)
 	result = acpi_bus_init();
 
 	if (!result) {
+		pci_mmcfg_late_init();
 		if (!(pm_flags & PM_APM))
 			pm_flags |= PM_ACPI;
 		else {
include/linux/pci.h +8 -0
Index: linux-2.6/include/linux/pci.h
===================================================================
@@ -1050,5 +1050,13 @@ extern unsigned long pci_cardbus_mem_siz
 
 extern int pcibios_add_platform_entries(struct pci_dev *dev);
 
+#ifdef CONFIG_PCI_MMCONFIG
+extern void __init pci_mmcfg_early_init(int type);
+extern void __init pci_mmcfg_late_init(void);
+#else
+static inline void pci_mmcfg_early_init(int type) { }
+static inline void pci_mmcfg_late_init(void) { }
+#endif
+
 #endif /* __KERNEL__ */
 #endif /* LINUX_PCI_H */
author
#1 lore raw

PATCH 2/4 x86: clear pci_mmcfg_virt when mmcfg get rejected

From: Yinghai Lu <[email protected]>

For x86_64, need to free pci_mmcfg_virt, and iounmap some pointers when MMCONF is not reserved in E820 or acpi _CRS and get rejected

Cc Greg KH <[email protected]>
Cc Ingo Molnar <[email protected]>
Cc Thomas Gleixner <[email protected]>
Cc Andi Kleen <[email protected]>

---

 arch/x86/pci/mmconfig-shared.c |    1 +
 arch/x86/pci/mmconfig_32.c     |    4 ++++
 arch/x86/pci/mmconfig_64.c     |   22 +++++++++++++++++++++-
 arch/x86/pci/pci.h             |    1 +
 4 files changed, 27 insertions(+), 1 deletion(-)
arch/x86/pci/mmconfig-shared.c +1 -0
Index: linux-2.6/arch/x86/pci/mmconfig-shared.c
===================================================================
@@ -300,6 +300,7 @@ static void __init pci_mmcfg_reject_brok
 
 reject:
 	printk(KERN_ERR "PCI: Not using MMCONFIG.\n");
+	pci_mmcfg_arch_free();
 	kfree(pci_mmcfg_config);
 	pci_mmcfg_config = NULL;
 	pci_mmcfg_config_num = 0;
arch/x86/pci/mmconfig_32.c +4 -0
Index: linux-2.6/arch/x86/pci/mmconfig_32.c
===================================================================
@@ -136,3 +136,7 @@ int __init pci_mmcfg_arch_init(void)
 	raw_pci_ext_ops = &pci_mmcfg;
 	return 1;
 }
+
+void __init pci_mmcfg_arch_free(void)
+{
+}
arch/x86/pci/mmconfig_64.c +21 -1
Index: linux-2.6/arch/x86/pci/mmconfig_64.c
===================================================================
@@ -127,7 +127,7 @@ static void __iomem * __init mcfg_iorema
 int __init pci_mmcfg_arch_init(void)
 {
 	int i;
-	pci_mmcfg_virt = kmalloc(sizeof(*pci_mmcfg_virt) *
+	pci_mmcfg_virt = kzalloc(sizeof(*pci_mmcfg_virt) *
 				 pci_mmcfg_config_num, GFP_KERNEL);
 	if (pci_mmcfg_virt == NULL) {
 		printk(KERN_ERR "PCI: Can not allocate memory for mmconfig structures\n");
@@ -141,9 +141,29 @@ int __init pci_mmcfg_arch_init(void)
 			printk(KERN_ERR "PCI: Cannot map mmconfig aperture for "
 					"segment %d\n",
 				pci_mmcfg_config[i].pci_segment);
+			pci_mmcfg_arch_free();
 			return 0;
 		}
 	}
 	raw_pci_ext_ops = &pci_mmcfg;
 	return 1;
 }
+
+void __init pci_mmcfg_arch_free(void)
+{
+	int i;
+
+	if (pci_mmcfg_virt == NULL)
+		return;
+
+	for (i = 0; i < pci_mmcfg_config_num; ++i) {
+		if (pci_mmcfg_virt[i].virt) {
+			iounmap(pci_mmcfg_virt[i].virt);
+			pci_mmcfg_virt[i].virt = NULL;
+			pci_mmcfg_virt[i].cfg = NULL;
+		}
+	}
+
+	kfree(pci_mmcfg_virt);
+	pci_mmcfg_virt = NULL;
+}
arch/x86/pci/pci.h +1 -0
Index: linux-2.6/arch/x86/pci/pci.h
===================================================================
@@ -105,6 +105,7 @@ extern void pcibios_sort(void);
 /* pci-mmconfig.c */
 
 extern int __init pci_mmcfg_arch_init(void);
+extern void __init pci_mmcfg_arch_free(void);
 
 /*
  * AMD Fam10h CPUs are buggy, and cannot access MMIO config space
author
#2 lore raw

PATCH 3/4 x86: mmconf enable mcfg early

From: Yinghai Lu <[email protected]>

Patch
x86: validate against ACPI motherboard resources

changed the mmconf init sequence, and init MMCONF late in acpi_init.

here change it back to old sequence
1. check hostbridge in early
2. check MCFG with e820 in early
3. if all fail, will check MCFg with acpi _CRS in acpi_init

So we can make MCONF working again when acpi=off is set if hostbridge support that.

Cc Greg KH <[email protected]>
Cc Ingo Molnar <[email protected]>
Cc Thomas Gleixner <[email protected]>
Cc Andi Kleen <[email protected]>

---

 arch/x86/pci/mmconfig-shared.c |  106 +++++++++++++++++--------------
 1 file changed, 61 insertions(+), 45 deletions(-)
arch/x86/pci/mmconfig-shared.c +60 -46
Index: linux-2.6/arch/x86/pci/mmconfig-shared.c
===================================================================
@@ -241,7 +241,7 @@ static int __init is_acpi_reserved(unsig
 	return mcfg_res.flags;
 }
 
-static void __init pci_mmcfg_reject_broken(void)
+static void __init pci_mmcfg_reject_broken(int type, int early)
 {
 	typeof(pci_mmcfg_config[0]) *cfg;
 	int i;
@@ -266,34 +266,43 @@ static void __init pci_mmcfg_reject_brok
 	}
 
 	for (i = 0; i < pci_mmcfg_config_num; i++) {
+		int valid = 0;
 		u32 size = (cfg->end_bus_number + 1) << 20;
 		cfg = &pci_mmcfg_config[i];
-		printk(KERN_NOTICE "PCI: MCFG configuration %d: base %lu "
+		printk(KERN_NOTICE "PCI: MCFG configuration %d: base %lx "
 		       "segment %hu buses %u - %u\n",
 		       i, (unsigned long)cfg->address, cfg->pci_segment,
 		       (unsigned int)cfg->start_bus_number,
 		       (unsigned int)cfg->end_bus_number);
-		if (is_acpi_reserved(cfg->address, cfg->address + size - 1)) {
+
+		if (!early &&
+		    is_acpi_reserved(cfg->address, cfg->address + size - 1)) {
 			printk(KERN_NOTICE "PCI: MCFG area at %Lx reserved "
 			       "in ACPI motherboard resources\n",
 			       cfg->address);
-		} else {
+			valid = 1;
+		}
+
+		if (valid)
+			continue;
+
+		if (!early)
 			printk(KERN_ERR "PCI: BIOS Bug: MCFG area at %Lx is not"
 			       " reserved in ACPI motherboard resources\n",
 			       cfg->address);
-			/* Don't try to do this check unless configuration
-			   type 1 is available. */
-			if ((pci_probe & PCI_PROBE_CONF1) &&
-			    e820_all_mapped(cfg->address,
-					    cfg->address + size - 1,
-					    E820_RESERVED))
-				printk(KERN_NOTICE
-				       "PCI: MCFG area at %Lx reserved in "
-				       "E820\n",
-				       cfg->address);
-			else
-				goto reject;
+		/* Don't try to do this check unless configuration
+		   type 1 is available. */
+		if (type == 1 && e820_all_mapped(cfg->address,
+						  cfg->address + size - 1,
+						  E820_RESERVED)) {
+			printk(KERN_NOTICE
+			       "PCI: MCFG area at %Lx reserved in E820\n",
+			       cfg->address);
+			valid = 1;
 		}
+
+		if (!valid)
+			goto reject;
 	}
 
 	return;
@@ -306,46 +315,36 @@ reject:
 	pci_mmcfg_config_num = 0;
 }
 
-void __init pci_mmcfg_early_init(int type)
-{
-	if ((pci_probe & PCI_PROBE_MMCONF) == 0)
-		return;
-
-	/* If type 1 access is available, no need to enable MMCONFIG yet, we can
-	   defer until later when the ACPI interpreter is available to better
-	   validate things. */
-	if (type == 1)
-		return;
-
-	acpi_table_parse(ACPI_SIG_MCFG, acpi_parse_mcfg);
-
-	if ((pci_mmcfg_config_num == 0) ||
-	    (pci_mmcfg_config == NULL) ||
-	    (pci_mmcfg_config[0].address == 0))
-		return;
+static int __initdata known_bridge;
 
-	if (pci_mmcfg_arch_init())
-		pci_probe = (pci_probe & ~PCI_PROBE_MASK) | PCI_PROBE_MMCONF;
-}
-
-void __init pci_mmcfg_late_init(void)
+void __init __pci_mmcfg_init(int type, int early)
 {
-	int known_bridge = 0;
-
 	/* MMCONFIG disabled */
 	if ((pci_probe & PCI_PROBE_MMCONF) == 0)
 		return;
 
 	/* MMCONFIG already enabled */
-	if (!(pci_probe & PCI_PROBE_MASK & ~PCI_PROBE_MMCONF))
+	if (!early && !(pci_probe & PCI_PROBE_MASK & ~PCI_PROBE_MMCONF))
 		return;
 
-	if ((pci_probe & PCI_PROBE_CONF1) && pci_mmcfg_check_hostbridge())
-		known_bridge = 1;
-	else
-		acpi_table_parse(ACPI_SIG_MCFG, acpi_parse_mcfg);
+	/* for late to exit */
+	if (known_bridge)
+		return;
 
-	pci_mmcfg_reject_broken();
+	if (early && type == 1) {
+		if (pci_mmcfg_check_hostbridge())
+			known_bridge = 1;
+#if 0
+	/* check e820 in late? */
+		else
+			return;
+#endif
+	}
+
+	if (!known_bridge) {
+		acpi_table_parse(ACPI_SIG_MCFG, acpi_parse_mcfg);
+		pci_mmcfg_reject_broken(type, early);
+	}
 
 	if ((pci_mmcfg_config_num == 0) ||
 	    (pci_mmcfg_config == NULL) ||
@@ -365,6 +364,21 @@ void __init pci_mmcfg_late_init(void)
 	}
 }
 
+void __init pci_mmcfg_early_init(int type)
+{
+	__pci_mmcfg_init(type, 1);
+}
+
+void __init pci_mmcfg_late_init(void)
+{
+	int type = 0;
+
+	if (pci_probe & PCI_PROBE_CONF1)
+		type = 1;
+
+	__pci_mmcfg_init(type, 0);
+}
+
 static int __init pci_mmcfg_late_insert_resources(void)
 {
 	/*
author
#3 lore raw

PATCH 4/4 x86_64: check msr to get mmconfig for amd family 10h opteron v3

From: Yinghai Lu <[email protected]>

so even booting kernel with acpi=off or even MCFG is not there, we still can use MMCONFIG.

Cc Thomas Gleixner <[email protected]>
Cc Ingo Molnar <[email protected]>
Cc Andi Kleen <[email protected]>
Cc Greg KH <[email protected]>
Cc "H. Peter Anvin" <[email protected]>

---

 arch/x86/pci/mmconfig-shared.c |   67 ++++++++++++++++++++++++++++---
 1 file changed, 61 insertions(+), 6 deletions(-)
arch/x86/pci/mmconfig-shared.c +61 -6
Index: linux-2.6/arch/x86/pci/mmconfig-shared.c
===================================================================
@@ -100,33 +100,88 @@ static const char __init *pci_mmcfg_inte
 	return "Intel Corporation 945G/GZ/P/PL Express Memory Controller Hub";
 }
 
+static const char __init *pci_mmcfg_amd_fam10h(void)
+{
+	u32 low, high, address;
+	u64 base, msr;
+	int i;
+	unsigned segnbits = 0, busnbits;
+
+	address = MSR_FAM10H_MMIO_CONF_BASE;
+	if (rdmsr_safe(address, &low, &high))
+		return NULL;
+
+	msr = high;
+	msr <<= 32;
+	msr |= low;
+
+	/* mmconfig is not enable */
+	if (!(msr & FAM10H_MMIO_CONF_ENABLE))
+		return NULL;
+
+	base = msr & (FAM10H_MMIO_CONF_BASE_MASK<<FAM10H_MMIO_CONF_BASE_SHIFT);
+
+	busnbits = (msr >> FAM10H_MMIO_CONF_BUSRANGE_SHIFT) &
+			 FAM10H_MMIO_CONF_BUSRANGE_MASK;
+	if (busnbits > 8) {
+		segnbits = busnbits - 8;
+		busnbits = 8;
+	}
+
+	pci_mmcfg_config_num = (1 << segnbits);
+	pci_mmcfg_config = kzalloc(sizeof(pci_mmcfg_config[0]) *
+				   pci_mmcfg_config_num, GFP_KERNEL);
+	if (!pci_mmcfg_config)
+		return NULL;
+
+	for (i = 0; i < (1 << segnbits); i++) {
+		pci_mmcfg_config[i].address = base + (1<<28) * i;
+		pci_mmcfg_config[i].pci_segment = i;
+		pci_mmcfg_config[i].start_bus_number = 0;
+		pci_mmcfg_config[i].end_bus_number = (1 << busnbits) - 1;
+	}
+
+	return "AMD Family 10h NB";
+}
+
 struct pci_mmcfg_hostbridge_probe {
+	u32 bus;
+	u32 devfn;
 	u32 vendor;
 	u32 device;
 	const char *(*probe)(void);
 };
 
 static struct pci_mmcfg_hostbridge_probe pci_mmcfg_probes[] __initdata = {
-	{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_E7520_MCH, pci_mmcfg_e7520 },
-	{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82945G_HB, pci_mmcfg_intel_945 },
+	{ 0, PCI_DEVFN(0, 0), PCI_VENDOR_ID_INTEL,
+	  PCI_DEVICE_ID_INTEL_E7520_MCH, pci_mmcfg_e7520 },
+	{ 0, PCI_DEVFN(0, 0), PCI_VENDOR_ID_INTEL,
+	  PCI_DEVICE_ID_INTEL_82945G_HB, pci_mmcfg_intel_945 },
+	{ 0, PCI_DEVFN(0x18, 0), PCI_VENDOR_ID_AMD,
+	  0x1200, pci_mmcfg_amd_fam10h },
+	{ 0xff, PCI_DEVFN(0, 0), PCI_VENDOR_ID_AMD,
+	  0x1200, pci_mmcfg_amd_fam10h },
 };
 
 static int __init pci_mmcfg_check_hostbridge(void)
 {
 	u32 l;
+	u32 bus, devfn;
 	u16 vendor, device;
 	int i;
 	const char *name;
 
-	pci_direct_conf1.read(0, 0, PCI_DEVFN(0,0), 0, 4, &l);
-	vendor = l & 0xffff;
-	device = (l >> 16) & 0xffff;
-
 	pci_mmcfg_config_num = 0;
 	pci_mmcfg_config = NULL;
 	name = NULL;
 
 	for (i = 0; !name && i < ARRAY_SIZE(pci_mmcfg_probes); i++) {
+		bus =  pci_mmcfg_probes[i].bus;
+		devfn = pci_mmcfg_probes[i].devfn;
+		pci_direct_conf1.read(0, bus, devfn, 0, 4, &l);
+		vendor = l & 0xffff;
+		device = (l >> 16) & 0xffff;
+
 		if (pci_mmcfg_probes[i].vendor == vendor &&
 		    pci_mmcfg_probes[i].device == device)
 			name = pci_mmcfg_probes[i].probe();
#4 lore raw

Re: [PATCH 4/4] x86_64: check msr to get mmconfig for amd family 10h opteron v3

Quoted 5 lines · On Mon, 11 Feb 2008 16:48:35 -0800 Yinghai Lu <[email protected]> wrote:

From: Yinghai Lu <[email protected]>

so even booting kernel with acpi=off or even MCFG is not there, we still can use MMCONFIG.

This patch threw a big reject. I didn't check why.

arch/x86/pci/mmconfig-shared.c static const char __init *pci_mmcfg_inte · line 181

Quoted 1 line
arch/x86/pci/mmconfig-shared.c +1 -0
+		pci_direct_conf1.read(0, bus, devfn, 0, 4, &l);

When I fixed the reject, compilation failed here.

arch/x86/pci/mmconfig-shared.c: In function 'pci_mmcfg_check_hostbridge':
arch/x86/pci/mmconfig-shared.c:214: error: 'pci_direct_conf1' undeclared (first use in this function)

What kernel are you patching?

author
#5 lore raw

Re: [PATCH 4/4] x86_64: check msr to get mmconfig for amd family 10h opteron v3

Quoted 16 lines · Andrew Morton
Quoted 5 lines · On Mon, 11 Feb 2008 16:48:35 -0800 Yinghai Lu <[email protected]> wrote:

From: Yinghai Lu <[email protected]>

so even booting kernel with acpi=off or even MCFG is not there, we still can use MMCONFIG.

This patch threw a big reject. I didn't check why.

arch/x86/pci/mmconfig-shared.c static const char __init *pci_mmcfg_inte · line 181

Quoted 1 line
arch/x86/pci/mmconfig-shared.c +1 -0
+		pci_direct_conf1.read(0, bus, devfn, 0, 4, &l);

When I fixed the reject, compilation failed here.

Quoted 6 lines

arch/x86/pci/mmconfig-shared.c: In function 'pci_mmcfg_check_hostbridge':
arch/x86/pci/mmconfig-shared.c:214: error: 'pci_direct_conf1' undeclared (first use in this function)

What kernel are you patching?

linus tree.

other three are ok?

YH

#6 lore raw

Re: [PATCH 4/4] x86_64: check msr to get mmconfig for amd family 10h opteron v3

Quoted 17 lines · On Mon, 11 Feb 2008 18:20:46 -0800 Yinghai Lu <[email protected]> wrote:
Quoted 16 lines · Andrew Morton
Quoted 5 lines · On Mon, 11 Feb 2008 16:48:35 -0800 Yinghai Lu <[email protected]> wrote:

From: Yinghai Lu <[email protected]>

so even booting kernel with acpi=off or even MCFG is not there, we still can use MMCONFIG.

This patch threw a big reject. I didn't check why.

arch/x86/pci/mmconfig-shared.c static const char __init *pci_mmcfg_inte · line 181

Quoted 1 line
arch/x86/pci/mmconfig-shared.c +1 -0
+		pci_direct_conf1.read(0, bus, devfn, 0, 4, &l);

When I fixed the reject, compilation failed here.

Quoted 8 lines
Quoted 6 lines

arch/x86/pci/mmconfig-shared.c: In function 'pci_mmcfg_check_hostbridge':
arch/x86/pci/mmconfig-shared.c:214: error: 'pci_direct_conf1' undeclared (first use in this function)

What kernel are you patching?

linus tree.

hm. So why didn't it compile? pci_direct_conf1 is defined over in arch/x86/pci/direct.c and is not mentioned in any header file.

Quoted 1 line

other three are ok?

Well, they applied, but I didn't review, build-test or merge them.

author
#7 lore raw

Re: [PATCH 4/4] x86_64: check msr to get mmconfig for amd family 10h opteron v3

Quoted 23 lines · Andrew Morton
Quoted 21 lines · On Mon, 11 Feb 2008 18:20:46 -0800 Yinghai Lu <[email protected]> wrote:
Quoted 20 lines · Andrew Morton
Quoted 5 lines · On Mon, 11 Feb 2008 16:48:35 -0800 Yinghai Lu <[email protected]> wrote:

From: Yinghai Lu <[email protected]>

so even booting kernel with acpi=off or even MCFG is not there, we still can use MMCONFIG.

This patch threw a big reject. I didn't check why.

Review

Quoted 1 line
(quoted diff) +1 -0
+		pci_direct_conf1.read(0, bus, devfn, 0, 4, &l);

When I fixed the reject, compilation failed here.

arch/x86/pci/mmconfig-shared.c: In function 'pci_mmcfg_check_hostbridge':
arch/x86/pci/mmconfig-shared.c:214: error: 'pci_direct_conf1' undeclared (first use in this function)

Quoted 7 lines
Quoted 4 lines
Quoted 2 lines

What kernel are you patching?

linus tree.

hm. So why didn't it compile? pci_direct_conf1 is defined over in arch/x86/pci/direct.c and is not mentioned in any header file.

it is in arch/x86/pci/pci.h

and arch/x86/pci/mmconf_shared.c has one
#include "pci.h"

did you compile that for 32 bit?

YH

http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=b6ce068a1285a24185b01be8a49021827516b3e1

arch/x86/pci/pci.h +11 -4
index 36cb44c..3431518 100644 (file)
@@ -85,10 +85,17 @@ extern spinlock_t pci_config_lock;
 extern int (*pcibios_enable_irq)(struct pci_dev *dev);
 extern void (*pcibios_disable_irq)(struct pci_dev *dev);
 
-extern int pci_conf1_write(unsigned int seg, unsigned int bus,
-                          unsigned int devfn, int reg, int len, u32 value);
-extern int pci_conf1_read(unsigned int seg, unsigned int bus,
-                         unsigned int devfn, int reg, int len, u32 *value);
+struct pci_raw_ops {
+       int (*read)(unsigned int domain, unsigned int bus, unsigned int devfn,
+                                               int reg, int len, u32 *val);
+       int (*write)(unsigned int domain, unsigned int bus, unsigned int devfn,
+                                               int reg, int len, u32 val);
+};
+
+extern struct pci_raw_ops *raw_pci_ops;
+extern struct pci_raw_ops *raw_pci_ext_ops;
+
+extern struct pci_raw_ops pci_direct_conf1;
 
 extern int pci_direct_probe(void);
 extern void pci_direct_init(int type);