Skip to contentSkip to conversation

ssb: Add Gigabit Ethernet driver

PATCH New Michael Buesch 1 participant 1 message Feb 29, 2008

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 ssb: Add Gigabit Ethernet driver

This adds the Gigabit Ethernet driver for the SSB Gigabit Ethernet core. This driver actually is a frontend to the Tigon3 driver. So the real work is done by tg3. This device is used in the Linksys WRT350N.

---

For 2.6.26

drivers/ssb/Kconfig +9 -0
Index: wireless-testing/drivers/ssb/Kconfig
===================================================================
@@ -125,4 +125,13 @@ config SSB_DRIVER_EXTIF
 
 	  If unsure, say N
 
+config SSB_DRIVER_GIGE
+	bool "SSB Broadcom Gigabit Ethernet driver"
+	depends on SSB_PCIHOST_POSSIBLE && SSB_EMBEDDED && MIPS
+	help
+	  Driver for the Sonics Silicon Backplane attached
+	  Broadcom Gigabit Ethernet.
+
+	  If unsure, say N
+
 endmenu
drivers/ssb/Makefile +1 -0
Index: wireless-testing/drivers/ssb/Makefile
===================================================================
@@ -11,6 +11,7 @@ ssb-y					+= driver_chipcommon.o
 ssb-$(CONFIG_SSB_DRIVER_MIPS)		+= driver_mipscore.o
 ssb-$(CONFIG_SSB_DRIVER_EXTIF)		+= driver_extif.o
 ssb-$(CONFIG_SSB_DRIVER_PCICORE)	+= driver_pcicore.o
+ssb-$(CONFIG_SSB_DRIVER_GIGE)		+= driver_gige.o
 
 # b43 pci-ssb-bridge driver
 # Not strictly a part of SSB, but kept here for convenience
drivers/ssb/driver_gige.c new file +294 -0

294 lines not on this page · raw message

include/linux/ssb/ssb_driver_gige.h new file +174 -0

174 lines not on this page · raw message

drivers/ssb/driver_pcicore.c +89 -71

172 lines not on this page · raw message

drivers/ssb/embedded.c +90 -0

99 lines not on this page · raw message

include/linux/ssb/ssb.h +7 -0
Index: wireless-testing/include/linux/ssb/ssb.h
===================================================================
@@ -422,5 +422,12 @@ extern int ssb_bus_powerup(struct ssb_bu
 extern u32 ssb_admatch_base(u32 adm);
 extern u32 ssb_admatch_size(u32 adm);
 
+/* PCI device mapping and fixup routines.
+ * Called from the architecture pcibios init code.
+ * These are only available on SSB_EMBEDDED configurations. */
+#ifdef CONFIG_SSB_EMBEDDED
+int ssb_pcibios_plat_dev_init(struct pci_dev *dev);
+int ssb_pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin);
+#endif /* CONFIG_SSB_EMBEDDED */
 
 #endif /* LINUX_SSB_H_ */
include/linux/ssb/ssb_driver_pci.h +19 -0
Index: wireless-testing/include/linux/ssb/ssb_driver_pci.h
===================================================================
@@ -1,6 +1,11 @@
 #ifndef LINUX_SSB_PCICORE_H_
 #define LINUX_SSB_PCICORE_H_
 
+#include <linux/types.h>
+
+struct pci_dev;
+
+
 #ifdef CONFIG_SSB_DRIVER_PCICORE
 
 /* PCI core registers. */
@@ -88,6 +93,9 @@ extern void ssb_pcicore_init(struct ssb_
 extern int ssb_pcicore_dev_irqvecs_enable(struct ssb_pcicore *pc,
 					  struct ssb_device *dev);
 
+int ssb_pcicore_plat_dev_init(struct pci_dev *d);
+int ssb_pcicore_pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin);
+
 
 #else /* CONFIG_SSB_DRIVER_PCICORE */
 
@@ -107,5 +115,16 @@ int ssb_pcicore_dev_irqvecs_enable(struc
 	return 0;
 }
 
+static inline
+int ssb_pcicore_plat_dev_init(struct pci_dev *d)
+{
+	return -ENODEV;
+}
+static inline
+int ssb_pcicore_pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
+{
+	return -ENODEV;
+}
+
 #endif /* CONFIG_SSB_DRIVER_PCICORE */
 #endif /* LINUX_SSB_PCICORE_H_ */
drivers/ssb/main.c +29 -1
Index: wireless-testing/drivers/ssb/main.c
===================================================================
@@ -14,6 +14,7 @@
 #include <linux/io.h>
 #include <linux/ssb/ssb.h>
 #include <linux/ssb/ssb_regs.h>
+#include <linux/ssb/ssb_driver_gige.h>
 #include <linux/dma-mapping.h>
 #include <linux/pci.h>
 
@@ -68,6 +69,25 @@ found:
 }
 #endif /* CONFIG_SSB_PCIHOST */
 
+int ssb_for_each_bus_call(unsigned long data,
+			  int (*func)(struct ssb_bus *bus, unsigned long data))
+{
+	struct ssb_bus *bus;
+	int res;
+
+	ssb_buses_lock();
+	list_for_each_entry(bus, &buses, list) {
+		res = func(bus, data);
+		if (res >= 0) {
+			ssb_buses_unlock();
+			return res;
+		}
+	}
+	ssb_buses_unlock();
+
+	return -ENODEV;
+}
+
 static struct ssb_device *ssb_device_get(struct ssb_device *dev)
 {
 	if (dev)
@@ -1171,7 +1191,14 @@ static int __init ssb_modinit(void)
 	err = b43_pci_ssb_bridge_init();
 	if (err) {
 		ssb_printk(KERN_ERR "Broadcom 43xx PCI-SSB-bridge "
-			   "initialization failed");
+			   "initialization failed\n");
+		/* don't fail SSB init because of this */
+		err = 0;
+	}
+	err = ssb_gige_init();
+	if (err) {
+		ssb_printk(KERN_ERR "SSB Broadcom Gigabit Ethernet "
+			   "driver initialization failed\n");
 		/* don't fail SSB init because of this */
 		err = 0;
 	}
@@ -1185,6 +1212,7 @@ fs_initcall(ssb_modinit);
 
 static void __exit ssb_modexit(void)
 {
+	ssb_gige_exit();
 	b43_pci_ssb_bridge_exit();
 	bus_unregister(&ssb_bustype);
 }
drivers/ssb/ssb_private.h +2 -0
Index: wireless-testing/drivers/ssb/ssb_private.h
===================================================================
@@ -118,6 +118,8 @@ extern u32 ssb_calc_clock_rate(u32 pllty
 extern int ssb_devices_freeze(struct ssb_bus *bus);
 extern int ssb_devices_thaw(struct ssb_bus *bus);
 extern struct ssb_bus *ssb_pci_dev_to_bus(struct pci_dev *pdev);
+int ssb_for_each_bus_call(unsigned long data,
+			  int (*func)(struct ssb_bus *bus, unsigned long data));
 
 /* b43_pci_bridge.c */
 #ifdef CONFIG_SSB_B43_PCI_BRIDGE
drivers/ssb/driver_mipscore.c +1 -0
Index: wireless-testing/drivers/ssb/driver_mipscore.c
===================================================================
@@ -209,6 +209,7 @@ void ssb_mipscore_init(struct ssb_mipsco
 			/* fallthrough */
 		case SSB_DEV_PCI:
 		case SSB_DEV_ETHERNET:
+		case SSB_DEV_ETHERNET_GBIT:
 		case SSB_DEV_80211:
 		case SSB_DEV_USB20_HOST:
 			/* These devices get their own IRQ line if available, the rest goes on IRQ0 */
Signature · 1 line
Greetings Michael.